| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fixes from Rafael Wysocki:
"All of these fix recent regressions in ACPICA, in the ACPI PCI IRQ
management code and in the ACPI AML debugger.
Specifics:
- Fix a lock ordering issue in ACPICA introduced by a recent commit
that attempted to fix a deadlock in the dynamic table loading code
which in turn appeared after changes related to the handling of
module-level AML also made in this cycle (Lv Zheng).
- Fix a recent regression in the ACPI IRQ management code that may
cause PCI drivers to be unable to register an IRQ if that IRQ
happens to be shared with a device on the ISA bus, like the
parallel port, by reverting one commit entirely and restoring the
previous behavior in two other places (Sinan Kaya).
- Fix a recent regression in the ACPI AML debugger introduced by the
commit that removed incorrect usage of IS_ERR_VALUE() from multiple
places (Lv Zheng)"
* tag 'acpi-4.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / debugger: Fix regression introduced by IS_ERR_VALUE() removal
ACPICA: Namespace: Fix namespace/interpreter lock ordering
ACPI,PCI,IRQ: separate ISA penalty calculation
Revert "ACPI, PCI, IRQ: remove redundant code in acpi_irq_penalty_init()"
ACPI,PCI,IRQ: factor in PCI possible
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"One fix for a recent cpuidle core change that, against all odds,
introduced a functional regression on Power systems and the fix for
the crash during resume from hibernation on x86-64 that has been in
the works for the last few weeks (it actually was ready last week, but
I wanted to allow the reporters to test if for some more time).
Specifics:
- Fix a recent performance regression on Power systems (powernv and
pseries) introduced by a core cpuidle commit that decreased the
precision of the last_residency conversion from nano- to
microseconds, which should not matter in theory, but turned out to
play not-so-well with the special "snooze" idle state on Power
(Shreyas B Prabhu).
- Fix a crash during resume from hibernation on x86-64 caused by
possible corruption of the kernel text part of page tables in the
last phase of image restoration exposed by a security-related
change during the 4.3 development cycle (Rafael Wysocki)"
* tag 'pm-4.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: Fix last_residency division
x86/power/64: Fix kernel text mapping corruption during image restoration
|
|
Pull block IO fixes from Jens Axboe:
"Three small fixes that have been queued up and tested for this series:
- A bug fix for xen-blkfront from Bob Liu, fixing an issue with
incomplete requests during migration.
- A fix for an ancient issue in retrieving the IO priority of a
different PID than self, preventing that task from going away while
we access it. From Omar.
- A writeback fix from Tahsin, fixing a case where we'd call ihold()
with a zero ref count inode"
* 'for-linus' of git://git.kernel.dk/linux-block:
block: fix use-after-free in sys_ioprio_get()
writeback: inode cgroup wb switch should not call ihold()
xen-blkfront: save uncompleted reqs in blkfront_resume()
|
|
Pull configfs fix from Christoph Hellwig:
"A fix from Marek for ppos handling in configfs_write_bin_file, which
was introduced in Linux 4.5, but didn't have any users until recently"
* tag 'configfs-for-4.7' of git://git.infradead.org/users/hch/configfs:
configfs: Remove ppos increment in configfs_write_bin_file
|
|
* acpica-fixes:
ACPICA: Namespace: Fix namespace/interpreter lock ordering
* acpi-pci-fixes:
ACPI,PCI,IRQ: separate ISA penalty calculation
Revert "ACPI, PCI, IRQ: remove redundant code in acpi_irq_penalty_init()"
ACPI,PCI,IRQ: factor in PCI possible
* acpi-debug-fixes:
ACPI / debugger: Fix regression introduced by IS_ERR_VALUE() removal
|
|
* pm-cpuidle-fixes:
cpuidle: Fix last_residency division
* pm-sleep-fixes:
x86/power/64: Fix kernel text mapping corruption during image restoration
|
|
The "expert" menu was broken (split) such that all entries in it after
KALLSYMS were displayed in the "General setup" area instead of in the
"Expert users" area. Fix this by adding one kconfig dependency.
Yes, the Expert users menu is fragile. Problems like this have happened
several times in the past. I will attempt to isolate the Expert users
menu if there is interest in that.
Fixes: 4d5d5664c900 ("x86: kallsyms: disable absolute percpu symbols on !SMP")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: stable@vger.kernel.org # 4.6
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull networking fixes from David Miller:
1) All users of AF_PACKET's fanout feature want a symmetric packet
header hash for load balancing purposes, so give it to them.
2) Fix vlan state synchronization in e1000e, from Jarod Wilson.
3) Use correct socket pointer in ip_skb_dst_mtu(), from Shmulik
Ladkani.
4) mlx5 bug fixes from Mohamad Haj Yahia, Daniel Jurgens, Matthew
Finlay, Rana Shahout, and Shaker Daibes. Mostly to do with
operation timeouts and PCI error handling.
5) Fix checksum handling in mirred packet action, from WANG Cong.
6) Set skb->dev correctly when transmitting in !protect_frames case of
macsec driver, from Daniel Borkmann.
7) Fix MTU calculation in geneve driver, from Haishuang Yan.
8) Missing netif_napi_del() in unregister path of qeth driver, from
Ursula Braun.
9) Handle malformed route netlink messages in decnet properly, from
Vergard Nossum.
10) Memory leak of percpu data in ipv6 routing code, from Martin KaFai
Lau.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
ipv6: Fix mem leak in rt6i_pcpu
net: fix decnet rtnexthop parsing
cxgb4: update latest firmware version supported
net/mlx5: Avoid setting unused var when modifying vport node GUID
bonding: fix enslavement slave link notifications
r8152: fix runtime function for RTL8152
qeth: delete napi struct when removing a qeth device
Revert "fsl/fman: fix error handling"
fsl/fman: fix error handling
cdc_ncm: workaround for EM7455 "silent" data interface
RDS: fix rds_tcp_init() error path
geneve: fix max_mtu setting
net: phy: dp83867: Fix initialization of PHYCR register
enc28j60: Fix race condition in enc28j60 driver
net: stmmac: Fix null-function call in ISR on stmmac1000
tipc: fix nl compat regression for link statistics
net: bcmsysport: Device stats are unsigned long
macsec: set actual real device for xmit when !protect_frames
net_sched: fix mirrored packets checksum
packet: Use symmetric hash for PACKET_FANOUT_HASH.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Here are a collection of small fixes: at this time, we've got a
slightly high amount, but all small and trivial fixes, and nothing
scary can be seen there"
* tag 'sound-4.7-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (21 commits)
ALSA: hda/realtek: Add Lenovo L460 to docking unit fixup
ALSA: timer: Fix negative queue usage by racy accesses
ASoC: rt5645: fix reg-2f default value.
ASoC: fsl_ssi: Fix number of words per frame for I2S-slave mode
ALSA: au88x0: Fix calculation in vortex_wtdma_bufshift()
ALSA: hda - Add PCI ID for Kabylake-H
ALSA: echoaudio: Fix memory allocation
ASoC: Intel: atom: fix missing breaks that would cause the wrong operation to execute
ALSA: hda - fix read before array start
ASoC: cx20442: set tty->receiver_room in v253_open
ASoC: ak4613: Enable cache usage to fix crashes on resume
ASoC: wm8940: Enable cache usage to fix crashes on resume
ASoC: Intel: Skylake: Initialize module list for Broxton
ASoC: wm5102: Correct supported channels on trace compressed DAI
ASoC: wm5110: Add missing route from OUT3R to SYSCLK
ASoC: rt5670: fix HP Playback Volume control
ASoC: hdmi-codec: select CONFIG_HDMI
ASoC: davinci-mcasp: Fix dra7 DMA offset when using CFG port
ASoC: hdac_hdmi: Fix potential NULL dereference
ASoC: ak4613: Remove owner assignment from platform_driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform
Pull chrome platform fix from Olof Johansson:
"A single fix this time, closing a window where ioctl args are fetched
twice"
* tag 'chrome-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
platform/chrome: cros_ec_dev - double fetch bug in ioctl
|
|
It was first reported and reproduced by Petr (thanks!) in
https://bugzilla.kernel.org/show_bug.cgi?id=119581
free_percpu(rt->rt6i_pcpu) used to always happen in ip6_dst_destroy().
However, after fixing a deadlock bug in
commit 9c7370a166b4 ("ipv6: Fix a potential deadlock when creating pcpu rt"),
free_percpu() is not called before setting non_pcpu_rt->rt6i_pcpu to NULL.
It is worth to note that rt6i_pcpu is protected by table->tb6_lock.
kmemleak somehow did not report it. We nailed it down by
observing the pcpu entries in /proc/vmallocinfo (first suggested
by Hannes, thanks!).
Signed-off-by: Martin KaFai Lau <kafai@fb.com>
Fixes: 9c7370a166b4 ("ipv6: Fix a potential deadlock when creating pcpu rt")
Reported-by: Petr Novopashenniy <pety@rusnet.ru>
Tested-by: Petr Novopashenniy <pety@rusnet.ru>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Hannes Frederic Sowa <hannes@stressinduktion.org>
Cc: Petr Novopashenniy <pety@rusnet.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dn_fib_count_nhs() could enter an infinite loop if nhp->rtnh_len == 0
(i.e. if userspace passes a malformed netlink message).
Let's use the helpers from net/nexthop.h which take care of all this
stuff. We can do exactly the same as e.g. fib_count_nexthops() and
fib_get_nhs() from net/ipv4/fib_semantics.c.
This fixes the softlockup for me.
Cc: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The FIFO unlocking mechanism in acpi_dbg has been broken by the
following commit:
Commit: 287980e49ffc0f6d911601e7e352a812ed27768e
Subject: remove lots of IS_ERR_VALUE abuses
It converted !IS_ERR_VALUE(ret) into !ret which was not entirely
correct. Fix the regression by taking ret > 0 into account too as
appropriate.
Fixes: 287980e49ffc (remove lots of IS_ERR_VALUE abuses)
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Simplifications, changelog & subject massage ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
We verify "u_cmd.outsize" and "u_cmd.insize" but we need to make sure
that those values have not changed between the two copy_from_user()
calls. Otherwise it could lead to a buffer overflow.
Additionally, cros_ec_cmd_xfer() can set s_cmd->insize to a lower value.
We should use the new smaller value so we don't copy too much data to
the user.
Reported-by: Pengfei Wang <wpengfeinudt@gmail.com>
Fixes: a841178445bb ('mfd: cros_ec: Use a zero-length array for command data')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Tested-by: Gwendal Grignou <gwendal@chromium.org>
Cc: <stable@vger.kernel.org> # v4.2+
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
There is a lock order issue in acpi_load_tables(). The namespace lock
is held before holding the interpreter lock.
With ACPI_MUTEX_DEBUG enabled in the kernel, this is printed to the
log during boot:
[ 0.885699] ACPI Error: Invalid acquire order: Thread 405884224 owns [ACPI_MTX_Namespace], wants [ACPI_MTX_Interpreter] (20160422/utmutex-263)
[ 0.885881] ACPI Error: Could not acquire AML Interpreter mutex (20160422/exutils-95)
[ 0.893846] ACPI Error: Mutex [0x0] is not acquired, cannot release (20160422/utmutex-326)
[ 0.894019] ACPI Error: Could not release AML Interpreter mutex (20160422/exutils-133)
The issue has been introduced by the following commit:
Commit: 2f38b1b16d9280689e5cfa47a4c50956bf437f0d
ACPICA Commit: bfe03ffcde8ed56a7eae38ea0b188aeb12f9c52e
Subject: ACPICA: Namespace: Fix a regression that MLC support triggers
dead lock in dynamic table loading
Which fixed a deadlock issue for acpi_ns_load_table() in
acpi_ex_add_table() but didn't take care of the lock order in
acpi_ns_load_table() correctly.
Originally (before the above commit), ACPICA used the
namespace/interpreter locks in the following 2 key code
paths:
1. Table loading:
acpi_ns_load_table
L(Namespace)
acpi_ns_parse_table
acpi_ns_one_complete_parse
U(Namespace)
2. Object evaluation:
acpi_ns_evaluate
L(Interpreter)
acpi_ps_execute_method
U(Interpreter)
acpi_ns_load_table
L(Namespace)
U(Namespace)
acpi_ev_initialize_region
L(Namespace)
U(Namespace)
address_space.setup
L(Namespace)
U(Namespace)
address_space.handler
L(Namespace)
U(Namespace)
acpi_os_wait_semaphore
acpi_os_acquire_mutex
acpi_os_sleep
L(Interpreter)
U(Interpreter)
During runtime, while acpi_ns_evaluate is called, the lock order is
always Interpreter -> Namespace.
In turn, the problematic commit acquires the locks in the following
order:
3. Table loading:
acpi_ns_load_table
L(Namespace)
acpi_ns_parse_table
L(Interpreter)
acpi_ns_one_complete_parse
U(Interpreter)
U(Namespace)
To fix the lock order issue, move the interpreter lock to
acpi_ns_load_table() to ensure the lock order correctness:
4. Table loading:
acpi_ns_load_table
L(Interpreter)
L(Namespace)
acpi_ns_parse_table
acpi_ns_one_complete_parse
U(Namespace)
U(Interpreter)
However, this doesn't fix the current design issues related to the
namespace lock. For example, we can notice that in acpi_ns_evaluate(),
outside of acpi_ns_load_table(), the namespace objects may be created
by the named object creation control methods. And the creation of
the method-owned namespace objects are not locked by the namespace
lock. This patch doesn't try to fix such kind of existing issues.
Fixes: 2f38b1b16d92 (ACPICA: Namespace: Fix a regression that MLC support triggers dead lock in dynamic table loading)
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Change t4fw_version.h to update latest firmware version number
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GCC complains on unused-but-set-variable, clean this up.
Fixes: 23898c763f4a ('net/mlx5: E-Switch, Modify node guid on vf set MAC')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, link notifications are not sent by
bond_set_slave_link_state() upon enslavement if
the slave is enslaved when up.
This happens because slave->link default init value
is 0, which is the same as BOND_LINK_UP, resulting
in bond_set_slave_link_state() ignoring this transition.
This patch sets the default value of slave->link to
BOND_LINK_NOCHANGE, assuring it will count as a state
transition and thus trigger notification logic.
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RTL8152 doesn't have U1U2 and U2P3 features, so use different
runtime functions for RTL812 and RTL8153 by adding autosuspend_en()
to rtl_ops.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This solves the issue that a headphone is not working on the docking
unit.
Signed-off-by: Torsten Hilbrich <torsten.hilbrich@secunet.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A qeth_card contains a napi_struct linked to the net_device during
device probing. This struct must be deleted when removing the qeth
device, otherwise Panic on oops can occur when qeth devices are
repeatedly removed and added.
Fixes: a1c3ed4c9ca ("qeth: NAPI support for l2 and l3 discipline")
Cc: stable@vger.kernel.org # v2.6.37+
Signed-off-by: Ursula Braun <ubraun@linux.vnet.ibm.com>
Tested-by: Alexander Klein <ALKL@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit a788a4a040e003574b8ad17115706ab1601ec572.
This patch is wrong, the type returned doesn't fit
what the error pointer macros expect.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is likely that checking 'fman->fifo_offset' instead of
'fman->cam_offset' is expected here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several Lenovo users have reported problems with their Sierra
Wireless EM7455 modem. The driver has loaded successfully and
the MBIM management channel has appeared to work, including
establishing a connection to the mobile network. But no frames
have been received over the data interface.
The problem affects all EM7455 and MC7455, and is assumed to
affect other modems based on the same Qualcomm chipset and
baseband firmware.
Testing narrowed the problem down to what seems to be a
firmware timing bug during initialization. Adding a short sleep
while probing is sufficient to make the problem disappear.
Experiments have shown that 1-2 ms is too little to have any
effect, while 10-20 ms is enough to reliably succeed.
Reported-by: Stefan Armbruster <ml001@armbruster-it.de>
Reported-by: Ralph Plawetzki <ralph@purejava.org>
Reported-by: Andreas Fett <andreas.fett@secunet.com>
Reported-by: Rasmus Lerdorf <rasmus@lerdorf.com>
Reported-by: Samo Ratnik <samo.ratnik@gmail.com>
Reported-and-tested-by: Aleksander Morgado <aleksander@aleksander.es>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If register_pernet_subsys() fails, we shouldn't try to call
unregister_pernet_subsys().
Fixes: 467fa15356 ("RDS-TCP: Support multiple RDS-TCP listen endpoints, one per netns.")
Cc: stable@vger.kernel.org
Cc: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Acked-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For ipv6+udp+geneve encapsulation data, the max_mtu should subtract
sizeof(ipv6hdr), instead of sizeof(iphdr).
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Snooze is a poll idle state in powernv and pseries platforms. Snooze
has a timeout so that if a CPU stays in snooze for more than target
residency of the next available idle state, then it would exit
thereby giving chance to the cpuidle governor to re-evaluate and
promote the CPU to a deeper idle state. Therefore whenever snooze
exits due to this timeout, its last_residency will be target_residency
of the next deeper state.
Commit e93e59ce5b85 "cpuidle: Replace ktime_get() with local_clock()"
changed the math around last_residency calculation. Specifically,
while converting last_residency value from nano- to microseconds, it
carries out right shift by 10. Because of that, in snooze timeout
exit scenarios last_residency calculated is roughly 2.3% less than
target_residency of the next available state. This pattern is picked
up by get_typical_interval() in the menu governor and therefore
expected_interval in menu_select() is frequently less than the
target_residency of any state other than snooze.
Due to this we are entering snooze at a higher rate, thereby
affecting the single thread performance.
Fix this by using more precise division via ktime_us_delta().
Fixes: e93e59ce5b85 "cpuidle: Replace ktime_get() with local_clock()"
Reported-by: Anton Blanchard <anton@samba.org>
Bisected-by: Shilpasri G Bhat <shilpa.bhat@linux.vnet.ibm.com>
Signed-off-by: Shreyas B. Prabhu <shreyas@linux.vnet.ibm.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Balbir Singh <bsingharora@gmail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The user timer tu->qused counter may go to a negative value when
multiple concurrent reads are performed since both the check and the
decrement of tu->qused are done in two individual locked contexts.
This results in bogus read outs, and the endless loop in the
user-space side.
The fix is to move the decrement of the tu->qused counter into the
same spinlock context as the zero-check of the counter.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse fix from Miklos Szeredi:
"This makes sure userspace filesystems are not broken by the parallel
lookups and readdir feature"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: serialize dirops by default
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs fixes from Miklos Szeredi:
"This contains fixes for a dentry leak, a regression in 4.6 noticed by
Docker users and missing write access checking in truncate"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: warn instead of error if d_type is not supported
ovl: get_write_access() in truncate
ovl: fix dentry leak for default_permissions
|
|
overlay needs underlying fs to support d_type. Recently I put in a
patch in to detect this condition and started failing mount if
underlying fs did not support d_type.
But this breaks existing configurations over kernel upgrade. Those who
are running docker (partially broken configuration) with xfs not
supporting d_type, are surprised that after kernel upgrade docker does
not run anymore.
https://github.com/docker/docker/issues/22937#issuecomment-229881315
So instead of erroring out, detect broken configuration and warn
about it. This should allow existing docker setups to continue
working after kernel upgrade.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: 45aebeaf4f67 ("ovl: Ensure upper filesystem supports d_type")
Cc: <stable@vger.kernel.org> 4.6
|
|
Pull MIPS fix from Ralf Baechle:
"Only a single fix for 4.7 pending at this point. It fixes an issue
that may lead to corruption of the cache mode bits in the page table"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix possible corruption of cache mode by mprotect.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
- tm: Always reclaim in start_thread() for exec() class syscalls from
Cyril Bur
- tm: Avoid SLB faults in treclaim/trecheckpoint when RI=0 from Michael
Neuling
- eeh: Fix wrong argument passed to eeh_rmv_device() from Gavin Shan
- Initialise pci_io_base as early as possible from Darren Stevens
* tag 'powerpc-4.7-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Initialise pci_io_base as early as possible
powerpc/tm: Avoid SLB faults in treclaim/trecheckpoint when RI=0
powerpc/eeh: Fix wrong argument passed to eeh_rmv_device()
powerpc/tm: Always reclaim in start_thread() for exec() class syscalls
|
|
When initializing the PHY control register, the FIFO depth bits are
written without reading the previous register value, i.e. all other
bits are overwritten with zero. This disables automatic MDI-X
configuration, which is enabled by default. Fix initialization by doing
a read/modify/write operation.
Signed-off-by: Stefan Hauser <stefan@shauser.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The interrupt worker code for the enc28j60 relies only on the TXIF flag to
determinate if the packet transmission was completed. However the datasheet
specifies in section 12.1.3 that TXERIF will clear the TXRTS after a
transmit abort. Also in section 12.1.4 that TXIF will be set
when TXRTS transitions from '1' to '0'. Therefore the TXIF flag is enabled
during transmission errors.
This causes a race condition, since the worker code will invoke
enc28j60_tx_clear() -> netif_wake_queue(), potentially invoking the
ndo_start_xmit function to send a new packet. The enc28j60_send_packet function
uses a workqueue that invokes enc28j60_hw_tx(). In between this function is
called, the worker from the interrupt handler will enter the path for error
handler because of the TXERIF flag, causing to invoke enc28j60_tx_clear() again
and releasing the packet scheduled for transmission, causing a kernel crash with
due a NULL pointer.
These crashes due a NULL pointer were observed under stress conditions of the
device. A BUG_ON() sequence was used to validate the issue was fixed, and has
been running without problems for 2 years now.
Signed-off-by: Diego Dompe <dompe@hpe.com>
Acked-by: Sergio Valverde <sergio.valverde@hpe.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
(resent due to overhelpful mail client corrupting patch)
At least on Meson GXBB, the CORE_IRQ_MTL_RX_OVERFLOW interrupt is thrown
with the stmmac1000 driver, which does not support set_rx_tail_ptr. With
this patch and the clock fixes, 1G ethernet works on ODROID-C2.
Signed-off-by: Matt Corallo <git@bluematt.me>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://people.freedesktop.org/~airlied/linux
Pull drm fixes frlm Dave Airlie:
"Just some AMD and Intel fixes, the AMD ones are further production
Polaris fixes, and the Intel ones fix some early timeouts, some PCI ID
changes and a couple of other fixes.
Still a bit Internet challenged here, hopefully end of next week will
solve it"
* tag 'drm-fixes-for-v4.7-rc6' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Fix missing unlock on error in i915_ppgtt_info()
drm/amd/powerplay: workaround for UVD clock issue
drm/amdgpu: add ACLK_CNTL setting for polaris10
drm/amd/powerplay: fix issue uvd dpm can't enabled on Polaris11.
drm/amd/powerplay: Workaround for Memory EDC Error on Polaris10.
drm/i915: Removing PCI IDs that are no longer listed as Kabylake.
drm/i915: Add more Kabylake PCI IDs.
drm/i915: Avoid early timeout during AUX transfers
drm/i915/hsw: Avoid early timeout during LCPLL disable/restore
drm/i915/lpt: Avoid early timeout during FDI PHY reset
drm/i915/bxt: Avoid early timeout during PLL enable
drm/i915: Refresh cached DP port register value on resume
drm/amd/powerplay: Update CKS on/ CKS off voltage offset calculation
drm/amd/powerplay: disable FFC.
drm/amd/powerplay: add some definition for FFC feature on polaris.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A few small driver-specific fixes for SPI, all in the normal important
if you hit them category especially the rockchip driver fix which
addresses a race which has been exposed more frequently with some
recent performance improvements"
* tag 'spi-fix-v4.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: sunxi: fix transfer timeout
spi: sun4i: fix FIFO limit
spi: rockchip: Signal unfinished DMA transfers
spi: spi-ti-qspi: Suspend the queue before removing the device
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator fixes from Mark Brown:
"Two small fixes for the regulator subsystem - one fixing a crash with
one of the devices supported by the max77620 driver, another fixing
startup for the anatop regulator when it starts up with the regulator
in bypass mode"
* tag 'regulator-fix-v4.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator:
regulator: max77620: check for valid regulator info
regulator: anatop: allow regulator to be in bypass mode
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A small fix for the newly added oxnas clk driver and a handful of
rockchip clk driver fixes for newly added rk3399 support"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: Fix return value check in oxnas_stdclk_probe()
clk: rockchip: release io resource when failing to init clk on rk3399
clk: rockchip: fix cpuclk registration error handling
clk: rockchip: Revert "clk: rockchip: reset init state before mmc card initialization"
clk: rockchip: fix incorrect parent for rk3399's {c,g}pll_aclk_perihp_src
clk: rockchip: mark rk3399 GIC clocks as critical
clk: rockchip: initialize flags of clk_init_data in mmc-phase clock
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v4.7
A small clutch of hardware specific fixes for various ASoC devices, all
small individually and important if you have that device but not
otherwise.
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
here's a batch of i915 fixes for 4.7.
* tag 'drm-intel-fixes-2016-06-30' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Fix missing unlock on error in i915_ppgtt_info()
drm/i915: Removing PCI IDs that are no longer listed as Kabylake.
drm/i915: Add more Kabylake PCI IDs.
drm/i915: Avoid early timeout during AUX transfers
drm/i915/hsw: Avoid early timeout during LCPLL disable/restore
drm/i915/lpt: Avoid early timeout during FDI PHY reset
drm/i915/bxt: Avoid early timeout during PLL enable
drm/i915: Refresh cached DP port register value on resume
|
|
into drm-fixes
Just a few more late fixes for Polaris cards.
* 'drm-fixes-4.7' of git://people.freedesktop.org/~agd5f/linux:
drm/amd/powerplay: workaround for UVD clock issue
drm/amdgpu: add ACLK_CNTL setting for polaris10
drm/amd/powerplay: fix issue uvd dpm can't enabled on Polaris11.
drm/amd/powerplay: Workaround for Memory EDC Error on Polaris10.
drm/amd/powerplay: Update CKS on/ CKS off voltage offset calculation
drm/amd/powerplay: disable FFC.
drm/amd/powerplay: add some definition for FFC feature on polaris.
|
|
The following testcase may result in a page table entries with a invalid
CCA field being generated:
static void *bindstack;
static int sysrqfd;
static void protect_low(int protect)
{
mprotect(bindstack, BINDSTACK_SIZE, protect);
}
static void sigbus_handler(int signal, siginfo_t * info, void *context)
{
void *addr = info->si_addr;
write(sysrqfd, "x", 1);
printf("sigbus, fault address %p (should not happen, but might)\n",
addr);
abort();
}
static void run_bind_test(void)
{
unsigned int *p = bindstack;
p[0] = 0xf001f001;
write(sysrqfd, "x", 1);
/* Set trap on access to p[0] */
protect_low(PROT_NONE);
write(sysrqfd, "x", 1);
/* Clear trap on access to p[0] */
protect_low(PROT_READ | PROT_WRITE | PROT_EXEC);
write(sysrqfd, "x", 1);
/* Check the contents of p[0] */
if (p[0] != 0xf001f001) {
write(sysrqfd, "x", 1);
/* Reached, but shouldn't be */
printf("badness, shouldn't happen but does\n");
abort();
}
}
int main(void)
{
struct sigaction sa;
sysrqfd = open("/proc/sysrq-trigger", O_WRONLY);
if (sigprocmask(SIG_BLOCK, NULL, &sa.sa_mask)) {
perror("sigprocmask");
return 0;
}
sa.sa_sigaction = sigbus_handler;
sa.sa_flags = SA_SIGINFO | SA_NODEFER | SA_RESTART;
if (sigaction(SIGBUS, &sa, NULL)) {
perror("sigaction");
return 0;
}
bindstack = mmap(NULL,
BINDSTACK_SIZE,
PROT_READ | PROT_WRITE | PROT_EXEC,
MAP_PRIVATE | MAP_ANONYMOUS, -1, 0);
if (bindstack == MAP_FAILED) {
perror("mmap bindstack");
return 0;
}
printf("bindstack: %p\n", bindstack);
run_bind_test();
printf("done\n");
return 0;
}
There are multiple ingredients for this:
1) PAGE_NONE is defined to _CACHE_CACHABLE_NONCOHERENT, which is CCA 3
on all platforms except SB1 where it's CCA 5.
2) _page_cachable_default must have bits set which are not set
_CACHE_CACHABLE_NONCOHERENT.
3) Either the defective version of pte_modify for XPA or the standard
version must be in used. However pte_modify for the 36 bit address
space support is no affected.
In that case additional bits in the final CCA mode may generate an invalid
value for the CCA field. On the R10000 system where this was tracked
down for example a CCA 7 has been observed, which is Uncached Accelerated.
Fixed by:
1) Using the proper CCA mode for PAGE_NONE just like for all the other
PAGE_* pte/pmd bits.
2) Fix the two affected variants of pte_modify.
Further code inspection also shows the same issue to exist in pmd_modify
which would affect huge page systems.
Issue in pte_modify tracked down by Alastair Bridgewater, PAGE_NONE
and pmd_modify issue found by me.
The history of this goes back beyond Linus' git history. Chris Dearman's
commit 351336929ccf222ae38ff0cb7a8dd5fd5c6236a0 ("[MIPS] Allow setting of
the cache attribute at run time.") missed the opportunity to fix this
but it was originally introduced in lmo commit
d523832cf12007b3242e50bb77d0c9e63e0b6518 ("Missing from last commit.")
and 32cc38229ac7538f2346918a09e75413e8861f87 ("New configuration option
CONFIG_MIPS_UNCACHED.")
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reported-by: Alastair Bridgewater <alastair.bridgewater@gmail.com>
|
|
Since commit 103544d86976 (ACPI,PCI,IRQ: reduce resource requirements)
the penalty values are calculated on the fly rather than at boot time.
This works fine for PCI interrupts but not so well for ISA interrupts.
The information on whether or not an ISA interrupt is in use is not
available to the pci_link.c code directly. That information is
obtained from the outside via acpi_penalize_isa_irq(). [If its
"active" argument is true, then the IRQ is in use by ISA.]
Since the current code relies on PCI Link objects for determination
of penalties, we are factoring in the PCI penalty twice after
acpi_penalize_isa_irq() function is called.
To avoid that, limit the newly added functionality to just PCI
interrupts so that old behavior is still maintained.
Fixes: 103544d86976 (ACPI,PCI,IRQ: reduce resource requirements)
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Tested-by: Wim Osterholt <wim@djo.tudelft.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Trying to make the ISA and PCI init functionality common turned out
to be a bad idea, because the ISA path depends on external
functionality.
Restore the previous behavior and limit the refactoring to PCI
interrupts only.
Fixes: 1fcb6a813c4f "ACPI,PCI,IRQ: remove redundant code in acpi_irq_penalty_init()"
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Tested-by: Wim Osterholt <wim@djo.tudelft.nl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The change introduced in commit 103544d86976 (ACPI,PCI,IRQ: reduce
resource requirements) omitted the initially applied PCI_POSSIBLE
penalty when the IRQ is active.
Incorrect calculation of the penalty leads the ACPI code to assigning
a wrong interrupt number to a PCI INTx interrupt.
This would not be as bad as it sounds in theory. It would just cause
the interrupts to be shared and result in performance penalty.
However, some drivers (like the parallel port driver) don't like
interrupt sharing and in the above case they will causes all of
the PCI drivers wanting to share the interrupt to be unable to
request it.
The issue has not been caught in testing because the behavior is
platform-specific and depends on the peripherals ending up sharing
the IRQ and their drivers.
Before the above commit the code would add the PCI_POSSIBLE value
divided by the number of possible IRQ users to the IRQ penalty
during initialization.
Later in that code path, if the IRQ is chosen as the active IRQ or
if it is used by ISA; additional penalties are added.
Fixes: 103544d86976 (ACPI,PCI,IRQ: reduce resource requirements)
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Tested-by: Wim Osterholt <wim@djo.tudelft.nl>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Fix an expression in the ACPI PCI IRQ management code added by a
recent commit that overlooked missing parens in it, so the result of
the computation is incorrect in some cases (Sinan Kaya)"
* tag 'acpi-4.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI,PCI,IRQ: correct operator precedence
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"Three cpufreq fixes, one in the core (stable-candidate) and two in
drivers (intel_pstate and cpufreq-dt).
Specifics:
- Fix a recent intel_pstate regression that caused the number of
wakeups to increase significantly on an idle system in some cases
due to excessive synchronize_sched() invocations (Rafael Wysocki).
- Fix unnecessary invocations of WARN_ON() in the cpufreq core after
cpufreq has been suspended introduced during the 4.6 cycla (Rafael
Wysocki).
- Fix an error code path in the cpufreq-dt-platdev driver that
forgets to drop a reference to a DT node (Masahiro Yamada)"
* tag 'pm-4.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: Avoid false-positive WARN_ON()s in cpufreq_update_policy()
cpufreq: dt: call of_node_put() before error out
intel_pstate: Do not clear utilization update hooks on policy changes
|
