| Age | Commit message (Collapse) | Author |
|---|
|
The general interrupt handler returns IRQ_HANDLED whether an IRQ
was handled or not.
Determine if an IRQ was handled and return the correct value.
Reviewed-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Reviewed-by: Michael J. Ruhl <michael.j.ruhl@intel.com>
Signed-off-by: Kamenee Arumugam <kamenee.arumugam@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Relying on a trailing magic value is incorrect. There are instances where
this is not present as trailing magic value has a specific purpose which is
not partition validation. Instead use the header magic value which is
present in all variants of the platform configuration and is intended for
validation. This is also used in other locations in the driver.
Fixes: bc5214ee2922 (IB/hfi1: Handle missing magic values in config file)
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Jan Sokolowski <jan.sokolowski@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
QSFP reset enables AOC transmitters by default. They should be off
before moving to high power mode to complete the setup. There is no
need to reset the QSFP during LNI failure as it was reset at link down.
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
Offline.quietDuration was added in the 8051 firmware, and the driver
only turns off the AOC transmitters when offline.quiet is reached.
However, the AOC transmitters need to be turned off at the new state.
Therefore, turn off the AOC transmitters at any offline substates
including offline.quiet and offline.quietDuration, then recheck we
reached offline.quiet to support backwards compatibility.
Reviewed-by: Jakub Byczkowski <jakub.byczkowski@intel.com>
Reviewed-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Sebastian Sanchez <sebastian.sanchez@intel.com>
Signed-off-by: Dennis Dalessandro <dennis.dalessandro@intel.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The definition of map_sg was split during a recent addition to iommu_ops.
Put it back together.
Fixes: add02cfdc9bc ("iommu: Introduce Interface for IOMMU TLB Flushing")
Signed-off-by: Jean-Philippe Brucker <jean-philippe.brucker@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
pr_err() messages should end with a new-line to avoid other messages
being concatenated. So replace '/n' with '\n'.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Fixes: 45a01c42933b ('iommu/amd: Add function copy_dev_tables()')
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The ARM short descriptor has already limited the physical address
to 32bit after the commit <76557391433c> ("iommu/io-pgtable: Sanitise
map/unmap addresses"). But in MediaTek 4GB mode, the physical address
is from 0x1_0000_0000 to 0x1_ffff_ffff. this will cause:
WARNING: CPU: 4 PID: 3900 at
xxx/drivers/iommu/io-pgtable-arm-v7s.c:482 arm_v7s_map+0x40/0xf8
Modules linked in:
CPU: 4 PID: 3900 Comm: weston Tainted: G S W 4.9.44 #1
Hardware name: MediaTek MT2712m1v1 board (DT)
task: ffffffc0eaa5b280 task.stack: ffffffc0e9858000
PC is at arm_v7s_map+0x40/0xf8
LR is at mtk_iommu_map+0x64/0x90
pc : [<ffffff80085b09e8>] lr : [<ffffff80085b29fc>] pstate: 000001c5
sp : ffffffc0e985b920
x29: ffffffc0e985b920 x28: 0000000127d00000
x27: 0000000000100000 x26: ffffff8008f9e000
x25: 0000000000000003 x24: 0000000000100000
x23: 0000000127d00000 x22: 00000000ff800000
x21: ffffffc0f7ec8ce0 x20: 0000000000000003
x19: 0000000000000003 x18: 0000000000000002
x17: 0000007f7e5d72c0 x16: ffffff80082b0f08
x15: 0000000000000001 x14: 000000000000003f
x13: 0000000000000000 x12: 0000000000000028
x11: 0088000000000000 x10: 0000000000000000
x9 : ffffff80092fa000 x8 : ffffffc0e9858000
x7 : ffffff80085b29d8 x6 : 0000000000000000
x5 : ffffff80085b09a8 x4 : 0000000000000003
x3 : 0000000000100000 x2 : 0000000127d00000
x1 : 00000000ff800000 x0 : 0000000000000001
...
Call trace:
[<ffffff80085b09e8>] arm_v7s_map+0x40/0xf8
[<ffffff80085b29fc>] mtk_iommu_map+0x64/0x90
[<ffffff80085ab5f8>] iommu_map+0x100/0x3a0
[<ffffff80085ab99c>] default_iommu_map_sg+0x104/0x168
[<ffffff80085aead8>] iommu_dma_alloc+0x238/0x3f8
[<ffffff8008098b30>] __iommu_alloc_attrs+0xa8/0x260
[<ffffff80085f364c>] mtk_drm_gem_create+0xac/0x180
[<ffffff80085f3894>] mtk_drm_gem_dumb_create+0x54/0xc8
[<ffffff80085d576c>] drm_mode_create_dumb_ioctl+0xa4/0xd8
[<ffffff80085cb2a0>] drm_ioctl+0x1c0/0x490
In order to satify this, Limit the physical address to 32bit.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Fix the commit 81b3c2521844 ("iommu/io-pgtable: Introduce explicit
coherency"). If there is no IO_PGTABLE_QUIRK_NO_DMA, we should call
dma_sync_single_for_device for cache synchronization.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Fixes: 81b3c2521844 ('iommu/io-pgtable: Introduce explicit coherency')
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Commit 1eeef2d7483a ("mtd: handle partitioning on devices with 0
erasesize") introduced a regression on heterogeneous erase region
devices. Alignment of the partition was tested against the master
eraseblock size which can be bigger than the slave one, thus leading
to some partitions being marked as read-only.
Update wr_alignment to match this slave erasesize after this erasesize
has been determined by picking the biggest erasesize of all the regions
embedded in the MTD partition.
Reported-by: Mathias Thore <Mathias.Thore@infinera.com>
Fixes: 1eeef2d7483a ("mtd: handle partitioning on devices with 0 erasesize")
Cc: <stable@vger.kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Mathias Thore <Mathias.Thore@infinera.com>
Reviewed-by: Mathias Thore <Mathias.Thore@infinera.com>
|
|
The simplify part: do not touch pi_desc.nv, we can set it when the
VCPU is first created. Likewise, pi_desc.sn is only handled by
vmx_vcpu_pi_load, do not touch it in __pi_post_block.
The fix part: do not check kvm_arch_has_assigned_device, instead
check the SN bit to figure out whether vmx_vcpu_pi_put ran before.
This matches what the previous patch did in pi_post_block.
Cc: Huangweidong <weidong.huang@huawei.com>
Cc: Gonglei <arei.gonglei@huawei.com>
Cc: wangxin <wangxinxin.wang@huawei.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Tested-by: Longpeng (Mike) <longpeng2@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
In some cases, for example involving hot-unplug of assigned
devices, pi_post_block can forget to remove the vCPU from the
blocked_vcpu_list. When this happens, the next call to
pi_pre_block corrupts the list.
Fix this in two ways. First, check vcpu->pre_pcpu in pi_pre_block
and WARN instead of adding the element twice in the list. Second,
always do the list removal in pi_post_block if vcpu->pre_pcpu is
set (not -1).
The new code keeps interrupts disabled for the whole duration of
pi_pre_block/pi_post_block. This is not strictly necessary, but
easier to follow. For the same reason, PI.ON is checked only
after the cmpxchg, and to handle it we just call the post-block
code. This removes duplication of the list removal code.
Cc: Huangweidong <weidong.huang@huawei.com>
Cc: Gonglei <arei.gonglei@huawei.com>
Cc: wangxin <wangxinxin.wang@huawei.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Tested-by: Longpeng (Mike) <longpeng2@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Simple code movement patch, preparing for the next one.
Cc: Huangweidong <weidong.huang@huawei.com>
Cc: Gonglei <arei.gonglei@huawei.com>
Cc: wangxin <wangxinxin.wang@huawei.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Tested-by: Longpeng (Mike) <longpeng2@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
When the kernel is entered at EL2 on an ARMv8.0 system, we construct
the EL1 pstate and make sure this uses the the EL1 stack pointer
(we perform an exception return to EL1h).
But if the kernel is either entered at EL1 or stays at EL2 (because
we're on a VHE-capable system), we fail to set SPsel, and use whatever
stack selection the higher exception level has choosen for us.
Let's not take any chance, and make sure that SPsel is set to one
before we decide the mode we're going to run in.
Cc: <stable@vger.kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Eric has reported that since commit d2faa415166b "quota: Do not acquire
dqio_sem for dquot overwrites in v2 format" test generic/232
occasionally fails due to quota information being incorrect. Indeed that
commit was too eager to remove dqio_sem completely from the path that
just overwrites quota structure with updated information. Although that
is innocent on its own, another process that inserts new quota structure
to the same block can perform read-modify-write cycle of that block thus
effectively discarding quota information update if they race in a wrong
way.
Fix the problem by acquiring dqio_sem for reading for overwrites of
quota structure. Note that it *is* possible to completely avoid taking
dqio_sem in the overwrite path however that will require modifying path
inserting / deleting quota structures to avoid RMW cycles of the full
block and for now it is not clear whether it is worth the hassle.
Fixes: d2faa415166b2883428efa92f451774ef44373ac
Reported-and-tested-by: Eric Whitney <enwlinux@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
My Fujitsu-Siemens Lifebook S6120 doesn't have the FUJ02E3 device,
but it does have FUJ02B1. That means we do register the backlight
device (and it even seems to work), but the code will oops as soon
as we try to set the backlight brightness because it's trying to
call call_fext_func() with a NULL device. Let's just skip those
function calls when the FUJ02E3 device is not present.
Cc: Jonathan Woithe <jwoithe@just42.net>
Cc: Andy Shevchenko <andy@infradead.org>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: <stable@vger.kernel.org> # 4.13.x
Signed-off-by: Darren Hart (VMware) <dvhart@infradead.org>
|
|
The sctp_for_each_transport() function takes an pointer to int. The
cb->args[] array holds longs so it's only using the high 32 bits. It
works on little endian system but will break on big endian 64 bit
machines.
Fixes: d25adbeb0cdb ("sctp: fix an use-after-free issue in sctp_sock_dump")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for 4.14
Quite a lot of fixes this time. Most notable is the brcmfmac fix for a
CVE issue.
iwlwifi
* a couple of bugzilla bugs related to multicast handling
* two fixes for WoWLAN bugs that were causing queue hangs and
re-initialization problems
* two fixes for potential uninitialized variable use reported by Dan
Carpenter in relation to a recently introduced patch
* a fix for buffer reordering in the newly supported 9000 device
family
* fix a race when starting aggregation
* small fix for a recent patch to wake mac80211 queues
* send non-bufferable management frames in the generic queue so they
are not sent on queues that are under power-save
ath10k
* fix a PCI PM related gcc warning
brcmfmac
* CVE-2017-0786: add length check scan results from firmware
* respect passive scan requests from user space
qtnfmac
* fix race in tx path when using multiple interfaces
* cancel ongoing scan when removing the wireless interface
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
- sdhci-pci: Fix voltage switch for some Intel host controllers
- tmio: remove broken and noisy debug macro
* tag 'mmc-v4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: sdhci-pci: Fix voltage switch for some Intel host controllers
mmc: tmio: remove broken and noisy debug macro
|
|
In generic_file_llseek_size, return -ENXIO for negative offsets as well
as offsets beyond EOF. This affects filesystems which don't implement
SEEK_HOLE / SEEK_DATA internally, possibly because they don't support
holes.
Fixes xfstest generic/448.
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Igor Russkikh says:
====================
aquantia: Atlantic driver bugfixes und improvements
This series contains bugfixes for aQuantia Atlantic driver.
Changes in v2:
Review comments applied:
- min_mtu set removed
- extra mtu range check is removed
- err codes handling improved
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call skb_frag_dma_map multiple times if tx length is greater than
device max and avoid processing tx ring until entire packet has been
sent.
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: Pavel Belous <pavel.belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Due to a bug in aquantia atlantic card firmware, it sometimes reports
invalid link speed bits. That caused driver to report link down events,
although link itself is totally fine.
This patch ignores such out of blue readings.
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver did a poor job in managing its Tx queues: Sometimes it could stop
tx queues due to link down condition in aq_nic_xmit - but never waked up
them. That led to Tx path total suspend.
This patch fixes this and improves generic queue management:
- introduces queue restart counter
- uses generic netif_ interface to disable and enable tx path
- refactors link up/down condition and introduces dmesg log event when
link changes.
- introduces new constant for minimum descriptors count required for queue
wakeup
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Although hardware is capable for almost 16K MTU, without max_mtu field
correctly set it only allows standard MTU to be used.
This patch enables max MTU, calculating it from hardware maximum frame size
of 16352 octets (including FCS).
Fixes: 5513e16421cb ("net: ethernet: aquantia: Fixes for aq_ndev_change_mtu")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: Igor Russkikh <igor.russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit fd26a88093ba we added a worst case estimate for rmapbt blocks
needed to satisfy the block mapping request. Since then, we added the
ability to reserve enough space in each AG such that we should never run
out of blocks to grow the rmapbt, which makes this calculation
unnecessary. Revert the commit because it makes the extra delalloc
indlen accounting unnecessary and incorrect.
Reported-by: Eryu Guan <eguan@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
My previous patch: d3a304b6292168b83b45d624784f973fdc1ca674 check for
XFS_LI_FAILED flag xfs_iflush done, so the failed item can be properly
resubmitted.
In the loop scanning other inodes being completed, it should check the
current item for the XFS_LI_FAILED, and not the initial one.
The state of the initial inode is checked after the loop ends
Kudos to Eric for catching this.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
We call __xfs_ag_resv_init to make a per-AG reservation for each AG.
This makes the reservation per-AG, not per-filesystem. Therefore, it
is incorrect to adjust m_ag_max_usable for each AG. Adjust it only
when we're reserving AG 0's blocks so that we only do it once per fs.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
|
|
Since commit d531d91d6990 ("xfs: always use unwritten extents for
direct I/O writes"), we start allocating unwritten extents for all
direct writes to allow appending aio in XFS.
But for dio writes that could extend file size we update the in-core
inode size first, then convert the unwritten extents to real
allocations at dio completion time in xfs_dio_write_end_io(). Thus a
racing direct read could see the new i_size and find the unwritten
extents first and read zeros instead of actual data, if the direct
writer also takes a shared iolock.
Fix it by updating the in-core inode size after the unwritten extent
conversion. To do this, introduce a new boolean argument to
xfs_iomap_write_unwritten() to tell if we want to update in-core
i_size or not.
Suggested-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Brian Foster <bfoster@redhat.com>
Signed-off-by: Eryu Guan <eguan@redhat.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
Executing xfs/104 test in a loop on Linux-v4.13 kernel on a ppc64
machine can cause the following NULL pointer dereference,
.queue_work_on+0x4c/0x80
.iomap_dio_bio_end_io+0xbc/0x1f0
.bio_endio+0x118/0x1f0
.blk_update_request+0xd0/0x470
.blk_mq_end_request+0x24/0xc0
.lo_complete_rq+0x40/0xe0
.__blk_mq_complete_request_remote+0x28/0x40
.flush_smp_call_function_queue+0xc4/0x1e0
.smp_ipi_demux_relaxed+0x8c/0x100
.icp_hv_ipi_action+0x54/0xa0
.__handle_irq_event_percpu+0x84/0x2c0
.handle_irq_event_percpu+0x28/0x80
.handle_percpu_irq+0x78/0xc0
.generic_handle_irq+0x40/0x70
.__do_irq+0x88/0x200
.call_do_irq+0x14/0x24
.do_IRQ+0x84/0x130
This occurs due to the following sequence of events,
1. Allocate dio for Direct I/O write.
2. Invoke iomap_apply() until iov_iter_count() bytes have been submitted.
- Assume that we have submitted atleast one bio. Hence iomap_dio->ref value
will be >= 2.
- If during the second iteration, iomap_apply() ends up returning -ENOSPC, we would
break out of the loop and since the 'ret' value is a negative number we
end up not allocating memory for super_block->s_dio_done_wq.
3. Meanwhile, iomap_dio_bio_end_io() is invoked for bios that have been
submitted and here the code ends up dereferencing the NULL pointer stored
at super_block->s_dio_done_wq.
This commit fixes the bug by allocating memory for
super_block->s_dio_done_wq before iomap_apply() is invoked.
Reported-by: Eryu Guan <eguan@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Eryu Guan <eguan@redhat.com>
Signed-off-by: Chandan Rajendra <chandan@linux.vnet.ibm.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
Currently only the blocksize is checked, but we should really be calling
bdev_dax_supported() which also tests to make sure we can get a
struct dax_device and that the dax_direct_access() path is working.
This is the same check that we do for the "-o dax" mount option in
xfs_fs_fill_super().
This does not fix the race issues that caused the XFS DAX inode option to
be disabled, so that option will still be disabled. If/when we re-enable
it, though, I think we will want this issue to have been fixed. I also do
think that we want to fix this in stable kernels.
Signed-off-by: Ross Zwisler <ross.zwisler@linux.intel.com>
CC: stable@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
If we try to delete the same tunnel twice, the first delete operation
does a lookup (l2tp_tunnel_get), finds the tunnel, calls
l2tp_tunnel_delete, which queues it for deletion by
l2tp_tunnel_del_work.
The second delete operation also finds the tunnel and calls
l2tp_tunnel_delete. If the workqueue has already fired and started
running l2tp_tunnel_del_work, then l2tp_tunnel_delete will queue the
same tunnel a second time, and try to free the socket again.
Add a dead flag to prevent firing the workqueue twice. Then we can
remove the check of queue_work's result that was meant to prevent that
race but doesn't.
Reproducer:
ip l2tp add tunnel tunnel_id 3000 peer_tunnel_id 4000 local 192.168.0.2 remote 192.168.0.1 encap udp udp_sport 5000 udp_dport 6000
ip l2tp add session name l2tp1 tunnel_id 3000 session_id 1000 peer_session_id 2000
ip link set l2tp1 up
ip l2tp del tunnel tunnel_id 3000
ip l2tp del tunnel tunnel_id 3000
Fixes: f8ccac0e4493 ("l2tp: put tunnel socket release on a workqueue")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Guillaume Nault <g.nault@alphalink.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running LTP IPsec tests, KASan might report:
BUG: KASAN: use-after-free in vti_tunnel_xmit+0xeee/0xff0 [ip_vti]
Read of size 4 at addr ffff880dc6ad1980 by task swapper/0/0
...
Call Trace:
<IRQ>
dump_stack+0x63/0x89
print_address_description+0x7c/0x290
kasan_report+0x28d/0x370
? vti_tunnel_xmit+0xeee/0xff0 [ip_vti]
__asan_report_load4_noabort+0x19/0x20
vti_tunnel_xmit+0xeee/0xff0 [ip_vti]
? vti_init_net+0x190/0x190 [ip_vti]
? save_stack_trace+0x1b/0x20
? save_stack+0x46/0xd0
dev_hard_start_xmit+0x147/0x510
? icmp_echo.part.24+0x1f0/0x210
__dev_queue_xmit+0x1394/0x1c60
...
Freed by task 0:
save_stack_trace+0x1b/0x20
save_stack+0x46/0xd0
kasan_slab_free+0x70/0xc0
kmem_cache_free+0x81/0x1e0
kfree_skbmem+0xb1/0xe0
kfree_skb+0x75/0x170
kfree_skb_list+0x3e/0x60
__dev_queue_xmit+0x1298/0x1c60
dev_queue_xmit+0x10/0x20
neigh_resolve_output+0x3a8/0x740
ip_finish_output2+0x5c0/0xe70
ip_finish_output+0x4ba/0x680
ip_output+0x1c1/0x3a0
xfrm_output_resume+0xc65/0x13d0
xfrm_output+0x1e4/0x380
xfrm4_output_finish+0x5c/0x70
Can be fixed if we get skb->len before dst_output().
Fixes: b9959fd3b0fa ("vti: switch to new ip tunnel code")
Fixes: 22e1b23dafa8 ("vti6: Support inter address family tunneling.")
Signed-off-by: Alexey Kodanev <alexey.kodanev@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As raw_cpu_generic_read() is a plain read from a raw_cpu_ptr() address,
it's possible (albeit unlikely) that the compiler will split the access
across multiple instructions.
In this_cpu_generic_read() we disable preemption but not interrupts
before calling raw_cpu_generic_read(). Thus, an interrupt could be taken
in the middle of the split load instructions. If a this_cpu_write() or
RMW this_cpu_*() op is made to the same variable in the interrupt
handling path, this_cpu_read() will return a torn value.
For native word types, we can avoid tearing using READ_ONCE(), but this
won't work in all cases (e.g. 64-bit types on most 32-bit platforms).
This patch reworks this_cpu_generic_read() to use READ_ONCE() where
possible, otherwise falling back to disabling interrupts.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Christoph Lameter <cl@linux.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Pranith Kumar <bobby.prani@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arch@vger.kernel.org
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The clk of grf must be enabled before writing grf
register for rk3399.
Signed-off-by: Nickey Yang <nickey.yang@rock-chips.com>
[the grf clock is already part of the binding since march 2017]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Amir reported a bug discovered by his cleaned up version of my
dm-log-writes xfstests where we were missing csums at certain replay
points. This is because fsx was doing an msync(), which essentially
fsync()'s a specific range of a file. We will log all modified extents,
but only search for the checksums in the range we are being asked to
sync. We cannot simply log the extents in the range we're being asked
because we are logging the inode item as it is currently, which if it
has had a i_size update before the msync means we will miss extents when
replaying. We could possibly get around this by marking the inode with
the transaction that extended the i_size to see if we have this case,
but this would be racy and we'd have to lock the whole range of the
inode to make sure we didn't have an ordered extent outside of our range
that was in the middle of completing.
Fix this simply by keeping track of the modified extents range and
logging the csums for the entire range of extents that we are logging.
This makes the xfstest pass.
Reported-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
commit 4246a0b63bd8 ("block: add a bi_error field to struct bio")
changed the logic of how dio read endio reports errors.
For single stripe dio read, %bio->bi_status reflects the error before
verifying checksum, and now we're updating it when data block matches
with its checksum, while in the mismatching case, %bio->bi_status is
not updated to relfect that.
When some blocks in a file have been corrupted on disk, reading such a
file ends up with
1) checksum errors are reported in kernel log
2) read(2) returns successfully with some content being 0x01.
In order to fix it, we need to report its checksum mismatch error to
the upper layer (dio layer in this case) as well.
Fixes: 4246a0b63bd8 ("block: add a bi_error field to struct bio")
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reported-by: Goffredo Baroncelli <kreijack@inwind.it>
Tested-by: Goffredo Baroncelli <kreijack@inwind.it>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Previously, we were calling del_qgroup_item, and ignoring the return code
resulting in a potential to have divergent in-memory state without an
error. Perhaps, it makes sense to handle this error code, and put the
filesystem into a read only, or similar state.
This patch only adds reporting of the error if the error is fatal,
(any error other than qgroup not found).
Signed-off-by: Sargun Dhillon <sargun@sargun.me>
Reviewed-by: Qu Wenruo <quwenruo.btrfs@gmx.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Currently even if the underlying disk reports failure on IO,
compressed read endio still gets to verify checksum and reports it as
a checksum error.
In fact, if some IO have failed during reading a compressed data
extent , there's no way the checksum could match, therefore, we can
skip that in order to return error quickly to the upper layer.
Please note that we need to do this after recording the failed mirror
index so that read-repair in the upper layer's endio can work
properly.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Tested-by: Paul Jones <paul@pauljones.id.au>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
The kernel oops happens at
kernel BUG at fs/btrfs/extent_io.c:2104!
...
RIP: clean_io_failure+0x263/0x2a0 [btrfs]
It's showing that read-repair code is using an improper mirror index.
This is due to the fact that compression read's endio hasn't recorded
the failed mirror index in %cb->orig_bio.
With this, btrfs's read-repair can work properly on reading compressed
data.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reported-by: Paul Jones <paul@pauljones.id.au>
Tested-by: Paul Jones <paul@pauljones.id.au>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
This seems to be a leftover of commit cf8cddd38bab ("btrfs: don't
abuse REQ_OP_* flags for btrfs_map_block").
It should use btrfs_op() helper to provide one of 'enum btrfs_map_op'
types.
Fixes: cf8cddd38bab ("btrfs: don't abuse REQ_OP_* flags for btrfs_map_block")
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: Satoru Takeuchi <satoru.takeuchi@gmail.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
It doesn't make sense to backup tree roots when doing fsync, since
during fsync those tree roots have not been consistent on disk.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: Qu Wenruo <quwenruo.btrfs@gmx.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Currently, "btrfs quota enable" would fail after "btrfs quota disable" on
the first time with syslog output "qgroup_rescan_init failed with -22", but
it would succeed on the second time.
When "quota disable" is called, BTRFS_FS_QUOTA_DISABLING flag bit will be
set in fs_info->flags in btrfs_quota_disable(), but it will not be droppd
in btrfs_run_qgroups() (which is called in btrfs_commit_transaction())
because quota_root has already been freed. If "quota enable" is called
after that, both BTRFS_FS_QUOTA_DISABLING and BTRFS_FS_QUOTA_ENABLED flag
would be dropped in the btrfs_run_qgroups() since quota_root is not NULL.
This leads to the failure of "quota enable" on the first time.
BTRFS_FS_QUOTA_DISABLING flag is not used outside of "quota disable"
context and is equivalent to whether quota_root is NULL or not.
btrfs_run_qgroups() checks whether quota_root is NULL or not in the first
place.
So, let's remove BTRFS_FS_QUOTA_DISABLING flag.
Signed-off-by: Tomohiro Misono <misono.tomohiro@jp.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
btrfs_cmp_data_prepare() (almost) always returns 0 i.e. ignoring errors
from gather_extent_pages(). While the pages are freed by
btrfs_cmp_data_free(), cmp->num_pages still has > 0. Then,
btrfs_extent_same() try to access the already freed pages causing faults
(or violates PageLocked assertion).
This patch just return the error as is so that the caller stop the process.
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Fixes: f441460202cb ("btrfs: fix deadlock with extent-same and readpage")
Cc: <stable@vger.kernel.org> # 4.2
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
`btrfs sub set-default` succeeds to set an ID which isn't corresponding to any
fs/file tree. If such the bad ID is set to a filesystem, we can't mount this
filesystem without specifying `subvol` or `subvolid` mount options.
Fixes: 6ef5ed0d386b ("Btrfs: add ioctl and incompat flag to set the default mount subvol")
Cc: <stable@vger.kernel.org>
Signed-off-by: Satoru Takeuchi <satoru.takeuchi@gmail.com>
Reviewed-by: Qu Wenruo <quwenruo.btrfs@gmx.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
ENOTSUPP should not be returned to the user program.
(cf. include/linux/errno.h)
Therefore, EOPNOTSUPP is used instead of ENOTSUPP.
Signed-off-by: Tsutomu Itoh <t-itoh@jp.fujitsu.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
__del_reloc_root should be called before freeing up reloc_root->node.
If not, calling __del_reloc_root() dereference reloc_root->node, causing
the system BUG.
Fixes: 6bdf131fac23 ("Btrfs: don't leak reloc root nodes on error")
Cc: <stable@vger.kernel.org> # 4.9
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
__endio_write_update_ordered() repeats the search until it reaches the end
of the specified range. This works well with direct IO path, because before
the function is called, it's ensured that there are ordered extents filling
whole the range. It's not the case, however, when it's called from
run_delalloc_range(): it is possible to have error in the midle of the loop
in e.g. run_delalloc_nocow(), so that there exisits the range not covered
by any ordered extents. By cleaning such "uncomplete" range,
__endio_write_update_ordered() stucks at offset where there're no ordered
extents.
Since the ordered extents are created from head to tail, we can stop the
search if there are no offset progress.
Fixes: 524272607e88 ("btrfs: Handle delalloc error correctly to avoid ordered extent hang")
Cc: <stable@vger.kernel.org> # 4.12
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: Qu Wenruo <quwenruo.btrfs@gmx.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Commit 524272607e88 ("btrfs: Handle delalloc error correctly to avoid
ordered extent hang") introduced btrfs_cleanup_ordered_extents() to cleanup
submitted ordered extents. However, it does not clear the ordered bit
(Private2) of corresponding pages. Thus, the following BUG occurs from
free_pages_check_bad() (on btrfs/125 with nospace_cache).
BUG: Bad page state in process btrfs pfn:3fa787
page:ffffdf2acfe9e1c0 count:0 mapcount:0 mapping: (null) index:0xd
flags: 0x8000000000002008(uptodate|private_2)
raw: 8000000000002008 0000000000000000 000000000000000d 00000000ffffffff
raw: ffffdf2acf5c1b20 ffffb443802238b0 0000000000000000 0000000000000000
page dumped because: PAGE_FLAGS_CHECK_AT_FREE flag(s) set
bad because of flags: 0x2000(private_2)
This patch clears the flag same as other places calling
btrfs_dec_test_ordered_pending() for every page in the specified range.
Fixes: 524272607e88 ("btrfs: Handle delalloc error correctly to avoid ordered extent hang")
Cc: <stable@vger.kernel.org> # 4.12
Signed-off-by: Naohiro Aota <naohiro.aota@wdc.com>
Reviewed-by: Qu Wenruo <quwenruo.btrfs@gmx.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
fs_info->super_copy->{node,sector}size are little-endian, but the ioctl
should return the values in native endianness. Use the cached values in
btrfs_fs_info instead. Found with sparse.
Fixes: 80a773fbfc2d ("btrfs: retrieve more info from FS_INFO ioctl")
Signed-off-by: Omar Sandoval <osandov@fb.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
flush_epd_write_bio() sets bio->bi_opf by itself to honor REQ_SYNC,
but it's not needed at all since bio->bi_opf has set up properly in
both __extent_writepage() and write_one_eb(), and in the case of
write_one_eb(), it also sets REQ_META, which we will lose in
flush_epd_write_bio().
This remove this unnecessary bio->bi_opf setting.
Signed-off-by: Liu Bo <bo.li.liu@oracle.com>
Reviewed-by: David Sterba <dsterba@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
