| Age | Commit message (Collapse) | Author |
|---|
|
The D-Link DGE-530T rev C1 is a re-badged Realtek 8169 named DLG10028C,
unlike the previous revisions which were skge based. It is probably
the same as the discontinued DGE-528T (0x4300) other than the PCI ID.
The PCI ID is 0x1186:0x4302.
Adding it to r8169.c where 0x1186:0x4300 is already found makes the card
be detected and work.
This fixes https://bugzilla.kernel.org/show_bug.cgi?id=38862
Signed-off-by: Len Sorensen <lsorense@csclub.uwaterloo.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mike McLagan hasn't contributed in many years and his email bounces.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: David Miller <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=34552
Signed-off-by: Klement Fish <klement2@azet.sk>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the min and max bit lengths for AES-CTR (RFC3686) keys.
The number of bits in key spec is the key length (128/256)
plus 32 bits of nonce.
This change takes care of the "Invalid key length" errors
reported by setkey when specifying 288 bit keys for aes-ctr.
Signed-off-by: Tushar Gohad <tgohad@mvista.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for voltage, current, and temperature peak (historic maximum)
attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
Add support for voltage, current, and temperature peak (historic maximum)
attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
|
|
Add support for voltage and temperature peak (historic maximum) attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
Add support for voltage and current peak (historic maximum) attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
Most PMBus devices provide manufacturer specific commands to read low and/or
high peak values for some or all of its sensors.
To support providing those values as lowest/highest attributes to the user,
introduce virtual PMBus commands. Those commands reside outside the normal
command set and have to be implemented in device specific code, which map the
virtual commands to device specific commands.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
Add the following attributes to the sysfs ABI.
in[0-*]_average
in[0-*]_lowest
in[0-*]_highest
in[0-*]_reset_history
in_reset_history
curr[1-*]_average
curr[1-*]_lowest
curr[1-*]_highest
curr[1-*]_reset_history
curr_reset_history
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
With virtual register page support, it is now possible that the status register
on virtual pages does not exist or is itself virtual. To take this into account
when creating alarm attributes, generate those attributes only if the status
register on the respective page is known to exist.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
Some PMBus chips have non-standard sensor registers. An easy way to
support such sensors is to introduce virtual pages and map the non-standard
registers into standard registers on an extra page.
For this to work, the code verifying if the configured number of pages exists
has to be removed. Since a wrong number of pages can only be configured in a
front-end driver, this should not have a practical impact since the resulting
errors should be found during development and testing.
Also, functions to read the chip status while checking if a command register
exists must be modified to no longer set the page register before reading the
status, since the physical page associated with the checked register may not
exist. This does not make a functional difference since the page was already set
when the attempt to read the register was made.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
specific code
Some PMBus devices use non-standard registers for some of the sensors and/or
limits. To support such devices, add code to support reading and writing of word
size registers in device specific code.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
CB tuning is needed to handle potential process variations that might
cause clock jitter for certain PLL settings. However, we were setting
it incorrectly since we were using the wrong M value as a check (M1 when
we needed to use the whole M value). Fix it up, making my HDMI
attached display a little prettier (used to have occasional dots crawl
across the display).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
|
Writes to the plane control register are buffered in the chip until a
write to the DSPADDR (pre-965) or DSPSURF (post-965) register occurs.
This patch adds flushes in:
intel_enable_plane
gen6_init_clock_gating
ivybridge_init_clock_gating
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
After writing to the plane control reg we need to write to the surface
reg to trigger the double buffered register latch. On previous
chipsets, writing to DSPADDR was enough, but on ILK+ DSPSURF is the reg
that triggers the double buffer latch.
v2: write DSPADDR too to cover pre-965 chipsets
v3: use flush_display_plane instead, that's what it's for
v4: send the right patch
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Tested-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
On CougarPoint and PantherPoint PCH chips, the timing generator may fail
to start after DP training completes. This is due to a bug in the
FDI autotraining detect logic (which will stall the timing generator and
re-enable it once training completes), so disable it to avoid silent DP
mode setting failures.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
This corrects the DPMS mode tracking so that the DPMS code will
actually turn the CRTC off the next time the screen saves.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
|
|
This reverts commit 885a50147f00a8a80108904bf58a18af357717f3.
We actually *do* need to track DPMS state so that on hotplug, we don't
retrain the link until DPMS is disabled.
However, that code had avery small bug -- it wouldn't set the
dpms_mode at mode set time, and so link retraining would not actually
occur on monitor hotplug until the monitor had gone through a DPMS
off/DPMS on cycle.
Signed-off-by: Keith Packard <keithp@keithp.com>
Tested-by: Andrew Lutomirski <luto@mit.edu>
|
|
Display port pipe selection on CPT is not done with a bit in the
output register, rather it is controlled by a couple of bits in the
separate transcoder register which indicate which display port output
is connected to the transcoder.
This patch replaces the simplistic macro DP_PIPE_ENABLED with the
rather more complicated function dp_pipe_enabled which checks the
output register to see if that is enabled, and then goes on to either
check the output register pipe selection bit (on non-CPT) or the
transcoder DP selection bits (on CPT).
Before this patch, any time the mode of pipe A was changed, any
display port outputs on pipe B would get disabled as
intel_disable_pch_ports would ensure that the mode setting operation
could occur on pipe A without interference from other outputs
connected to that pch port
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
|
|
Eliminates an open-coded read and also gains the retry behaviour of
intel_dp_get_dpcd, which seems like a good idea.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
|
|
This describes the function better, allowing it to be used where the
DPCD value is relevant.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
|
|
This uses the common dpcd reading routine, i915_dp_detect_common,
instead of open-coding a call to intel_dp_aux_native_read. Besides
reducing duplicated code, this also gains the read retries which
may be necessary when a cable is first plugged back in and the link
needs to be retrained.
Signed-off-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Adam Jackson <ajax@redhat.com>
|
|
drm_helper_hpd_irq_event queues another work proc to go and deliver
the user-space event, and that function also wants to hold the config
mutex, so we shouldn't hold the mutex across the
drm_helper_hpd_irq_event call.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
Some hwmon sysfs attributes have a length of 20 bytes (plus terminating 0).
I2C_NAME_SIZE is defined as 20 and thus can not be used to define the length
of hwmon sysfs attributes. Replace it with PMBUS_NAME_SIZE, set to 24.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
Add ADP4000, NCP4200 and NCP4208 to the list of devices supported by the generic
PMBus driver, and add device IDs to enable explicit instantiation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
|
|
In VID mode, output voltages are measured and reported as VID values, and
have to be converted to voltages using VID conversion tables or functions.
Support is added for VR11 only at this time.
This patch enables support for PMBus devices supporting VID VR11 based output
voltage selection such as NCP4200 and NCP4208.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
Since 43cc71eed1250755986da4c0f9898f9a635cb3bf (platform: prefix MODALIAS
with "platform:"), the platform modalias is prefixed with "platform:".
This patch changes the MODULE_ALIAS to "platform:ab8500-gpio".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
Allow GPIO drivers to use of_gpio_simple_xlate. This is useful for the
generic GPIO driver for example where gpio_chip is embedded in
bgpio_chip and doesn't need of_mm_gpio_chip but has a simple 1:1 GPIO
mapping.
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
iscsi target code uses lots on network interface functions, so it
should depend on NET. Fixes many build errors when NET is not enabled:
ERROR: "kernel_sendmsg" [drivers/target/iscsi/iscsi_target_mod.ko] undefined!
ERROR: "in_aton" [drivers/target/iscsi/iscsi_target_mod.ko] undefined!
ERROR: "sock_release" [drivers/target/iscsi/iscsi_target_mod.ko] undefined!
ERROR: "kernel_listen" [drivers/target/iscsi/iscsi_target_mod.ko] undefined!
ERROR: "kernel_setsockopt" [drivers/target/iscsi/iscsi_target_mod.ko] undefined!
ERROR: "kernel_recvmsg" [drivers/target/iscsi/iscsi_target_mod.ko] undefined!
ERROR: "kernel_accept" [drivers/target/iscsi/iscsi_target_mod.ko] undefined!
ERROR: "sock_create" [drivers/target/iscsi/iscsi_target_mod.ko] undefined!
ERROR: "kernel_bind" [drivers/target/iscsi/iscsi_target_mod.ko] undefined!
ERROR: "in6_pton" [drivers/target/iscsi/iscsi_target_mod.ko] undefined!
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
|
|
The logic at em28xx_isoc_dvb_max_packetsize() sucks, at least for newer
the needed packet size. Yet, it is better than nothing.
Rewrite the code in order to change the default to 752 for em2884 and
newer chips and provide a better way to handle per-chipset specifics.
For em2874, the current default should be enough, as the only em2874
board is currently a 1-seg ISDB-T board, so, it needs only a limited
amount of bandwidth.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Currently, the driver assumes that all QAM carriers are spaced with
8MHz. This is wrong, and may decrease QoS on Countries like Brazil,
that have DVB-C carriers with 6MHz-spaced.
Fortunately, both ITU-T J-83 and EN 300 429 specifies a way to
associate the symbol rate with the bandwidth needed for it.
For ITU-T J-83 2007 annex A, the maximum symbol rate for 6 MHz is:
6 MHz / 1.15 = 5217391 Bauds
For ITU-T J-83 2007 annex C, the maximum symbol rate for 6 MHz is:
6 MHz / 1.13 = 5309735 Bauds.
As this tuner is currently used only for DRX-K, and it is currently
hard-coded to annex A, I've opted to use the roll-off factor of 0.15,
instead of 0.13.
If we ever support annex C, the better would be to add a DVB S2API
call to allow changing between Annex A and C, and add the 0.13 roll-off
factor to it.
This code is currently being used on other frontends, so I think we
should later add a core function with this code, to warrant that
it will be properly implemented everywhere.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Since the number of PMBus drivers is getting large, move them into
directory drivers/hwmon/pmbus to improve readability and scalability.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
|
|
My previous commit left the file empty and present in the
Makefile, which is a bit dirty and caused problems with
'make distclean', as pointed out by David Howells.
This hopefully cleans it up the right way.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: John Linn <john.linn@xilinx.com>
|
|
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
|
|
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
|
|
instead of reading the registers everytime
the current implementation respect the following constrain:
- allow 1 to n soc to be enabled
- allow to have a virtual cpu type and subtype
- always detect the cpu type and subtype and report it
- detect if the soc support is enabled
- prepare for sysfs export support
- drop soc specific code via compiler when the soc not enabled
(via cpu_is_xxx)
Today if we read the exid we will have the same value for 9g35 and 9m11
and we will need to check the cidr too
with the new implementation we just need to check the soc subtype
this will also allow to have specific virtual subtype for rm9200 which the
board will have to specify via at91rm9200_set_type(int) as we have no way to
detect it.
this implementation is inspired by the SH cpu detection support
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
|
|
to make the soc base specified at runtime instead of compiled time
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
|
|
they are the same except the default priority
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
|
|
On all at91 except rm9200 and x40 have the System Controller starts
at address 0xffffc000 and has a size of 16KiB.
On rm9200 it's start at 0xfffe4000 of 111KiB with non reserved data starting
at 0xfffff000
This patch removes the individual definitions of AT91_BASE_SYS and
replaces them with a common version at base 0xfffffc000 and size 16KiB
and map the same memory space
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Patrice Vilchez <patrice.vilchez@atmel.com>
|
|
Convert array index from the loop bound to the loop index.
A simplified version of the semantic patch that fixes this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2,ar;
@@
for(e1 = 0; e1 < e2; e1++) { <...
ar[
- e2
+ e1
]
...> }
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
n2_crypto: Attach on Niagara-T3.
n2rng: Attach on Niagara-T3.
sparc: Detect and handle UltraSPARC-T3 cpu types.
sparc: Don't do expensive hypervisor PCR write unless necessary.
sparc: Add T3 sun4v cpu type and hypervisor group defines.
sparc: Don't leave sparc_pmu_type NULL on sun4v.
|
|
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (32 commits)
tg3: Remove 5719 jumbo frames and TSO blocks
tg3: Break larger frags into 4k chunks for 5719
tg3: Add tx BD budgeting code
tg3: Consolidate code that calls tg3_tx_set_bd()
tg3: Add partial fragment unmapping code
tg3: Generalize tg3_skb_error_unmap()
tg3: Remove short DMA check for 1st fragment
tg3: Simplify tx bd assignments
tg3: Reintroduce tg3_tx_ring_info
ASIX: Use only 11 bits of header for data size
ASIX: Simplify condition in rx_fixup()
Fix cdc-phonet build
bonding: reduce noise during init
bonding: fix string comparison errors
net: Audit drivers to identify those needing IFF_TX_SKB_SHARING cleared
net: add IFF_SKB_TX_SHARED flag to priv_flags
net: sock_sendmsg_nosec() is static
forcedeth: fix vlans
gianfar: fix bug caused by 87c288c6e9aa31720b72e2bc2d665e24e1653c3e
gro: Only reset frag0 when skb can be pulled
...
|
|
* 'for-linus' of git://neil.brown.name/md: (75 commits)
md/raid10: handle further errors during fix_read_error better.
md/raid10: Handle read errors during recovery better.
md/raid10: simplify read error handling during recovery.
md/raid10: record bad blocks due to write errors during resync/recovery.
md/raid10: attempt to fix read errors during resync/check
md/raid10: Handle write errors by updating badblock log.
md/raid10: clear bad-block record when write succeeds.
md/raid10: avoid writing to known bad blocks on known bad drives.
md/raid10 record bad blocks as needed during recovery.
md/raid10: avoid reading known bad blocks during resync/recovery.
md/raid10 - avoid reading from known bad blocks - part 3
md/raid10: avoid reading from known bad blocks - part 2
md/raid10: avoid reading from known bad blocks - part 1
md/raid10: Split handle_read_error out from raid10d.
md/raid10: simplify/reindent some loops.
md/raid5: Clear bad blocks on successful write.
md/raid5. Don't write to known bad block on doubtful devices.
md/raid5: write errors should be recorded as bad blocks if possible.
md/raid5: use bad-block log to improve handling of uncorrectable read errors.
md/raid5: avoid reading from known bad blocks.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
sound: oss: rename local change_bits to avoid powerpc bitsops.h definition
ALSA: hda - Fix duplicated DAC assignments for Realtek
ALSA: asihpi - off by one in asihpi_hpi_ioctl()
ALSA: hda - Fix Oops with Realtek quirks with NULL adc_nids
ALSA: asihpi - bug fix pa use before init.
ALSA: hda - Add support for vref-out based mute LED control on IDT codecs
|
|
Reduce high order allocations in do_tune_cpucache() for some setups.
(NR_CPUS=4096 -> we need 64KB)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Christoph Lameter <cl@linux.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
|
