summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-05-25m68k: mac: Remove misleading commentFinn Thain
This code path was tested on a Quadra 950 a long time ago and the comment isn't needed. Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Cc: Joshua Thompson <funaho@jurai.org> Link: https://lore.kernel.org/r/10dff3e7c17d363a4b239aae7b3ebab32bef3547.1589949122.git.fthain@telegraphics.com.au Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2020-05-25m68k: mac: Don't call via_flush_cache() on Mac IIfxFinn Thain
There is no VIA2 chip on the Mac IIfx, so don't call via_flush_cache(). This avoids a boot crash which appeared in v5.4. printk: console [ttyS0] enabled printk: bootconsole [debug0] disabled printk: bootconsole [debug0] disabled Calibrating delay loop... 9.61 BogoMIPS (lpj=48064) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) devtmpfs: initialized random: get_random_u32 called from bucket_table_alloc.isra.27+0x68/0x194 with crng_init=0 clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns futex hash table entries: 256 (order: -1, 3072 bytes, linear) NET: Registered protocol family 16 Data read fault at 0x00000000 in Super Data (pc=0x8a6a) BAD KERNEL BUSERR Oops: 00000000 Modules linked in: PC: [<00008a6a>] via_flush_cache+0x12/0x2c SR: 2700 SP: 01c1fe3c a2: 01c24000 d0: 00001119 d1: 0000000c d2: 00012000 d3: 0000000f d4: 01c06840 d5: 00033b92 a0: 00000000 a1: 00000000 Process swapper (pid: 1, task=01c24000) Frame format=B ssw=0755 isc=0200 isb=fff7 daddr=00000000 dobuf=01c1fed0 baddr=00008a6e dibuf=0000004e ver=f Stack from 01c1fec4: 01c1fed0 00007d7e 00010080 01c1fedc 0000792e 00000001 01c1fef4 00006b40 01c80000 00040000 00000006 00000003 01c1ff1c 004a545e 004ff200 00040000 00000000 00000003 01c06840 00033b92 004a5410 004b6c88 01c1ff84 000021e2 00000073 00000003 01c06840 00033b92 0038507a 004bb094 004b6ca8 004b6c88 004b6ca4 004b6c88 000021ae 00020002 00000000 01c0685d 00000000 01c1ffb4 0049f938 00409c85 01c06840 0045bd40 00000073 00000002 00000002 00000000 Call Trace: [<00007d7e>] mac_cache_card_flush+0x12/0x1c [<00010080>] fix_dnrm+0x2/0x18 [<0000792e>] cache_push+0x46/0x5a [<00006b40>] arch_dma_prep_coherent+0x60/0x6e [<00040000>] switched_to_dl+0x76/0xd0 [<004a545e>] dma_atomic_pool_init+0x4e/0x188 [<00040000>] switched_to_dl+0x76/0xd0 [<00033b92>] parse_args+0x0/0x370 [<004a5410>] dma_atomic_pool_init+0x0/0x188 [<000021e2>] do_one_initcall+0x34/0x1be [<00033b92>] parse_args+0x0/0x370 [<0038507a>] strcpy+0x0/0x1e [<000021ae>] do_one_initcall+0x0/0x1be [<00020002>] do_proc_dointvec_conv+0x54/0x74 [<0049f938>] kernel_init_freeable+0x126/0x190 [<0049f94c>] kernel_init_freeable+0x13a/0x190 [<004a5410>] dma_atomic_pool_init+0x0/0x188 [<00041798>] complete+0x0/0x3c [<000b9b0c>] kfree+0x0/0x20a [<0038df98>] schedule+0x0/0xd0 [<0038d604>] kernel_init+0x0/0xda [<0038d610>] kernel_init+0xc/0xda [<0038d604>] kernel_init+0x0/0xda [<00002d38>] ret_from_kernel_thread+0xc/0x14 Code: 0000 2079 0048 10da 2279 0048 10c8 d3c8 <1011> 0200 fff7 1280 d1f9 0048 10c8 1010 0000 0008 1080 4e5e 4e75 4e56 0000 2039 Disabling lock debugging due to kernel taint Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b Thanks to Stan Johnson for capturing the console log and running git bisect. Git bisect said commit 8e3a68fb55e0 ("dma-mapping: make dma_atomic_pool_init self-contained") is the first "bad" commit. I don't know why. Perhaps mach_l2_flush first became reachable with that commit. Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2") Reported-and-tested-by: Stan Johnson <userm57@yahoo.com> Signed-off-by: Finn Thain <fthain@telegraphics.com.au> Cc: Joshua Thompson <funaho@jurai.org> Link: https://lore.kernel.org/r/b8bbeef197d6b3898e82ed0d231ad08f575a4b34.1589949122.git.fthain@telegraphics.com.au Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
2020-05-25PM: runtime: Make clear what we do when conditions are wrong in rpm_suspend()Andy Shevchenko
rpm_suspend() simple bails out when conditions are wrong. But this is not immediately obvious from the code. Make it clear what we do when conditions are wrong in rpm_suspend(). Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
2020-05-25printk: Remove pr_cont_once()Tetsuo Handa
pr_cont_once() does not make sense; at least emitting module name using pr_fmt() into middle of a line (after e.g. pr_info_once()) does not make sense. Let's remove unused pr_cont_once(). Link: https://lore.kernel.org/r/20200524153243.11690-1-penguin-kernel@I-love.SAKURA.ne.jp Cc: Joe Perches <joe@perches.com> Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp> Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com> Signed-off-by: Petr Mladek <pmladek@suse.com>
2020-05-25mmc: block: Fix use-after-free issue for rpmbPeng Hao
The data structure member “rpmb->md” was passed to a call of the function “mmc_blk_put” after a call of the function “put_device”. Reorder these function calls to keep the data accesses consistent. Fixes: 1c87f7357849 ("mmc: block: Fix bug when removing RPMB chardev ") Signed-off-by: Peng Hao <richard.peng@oppo.com> Cc: stable@vger.kernel.org [Uffe: Fixed up mangled patch and updated commit message] Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2020-05-25Merge tag 'linux-cpupower-5.8-rc1' of ↵Rafael J. Wysocki
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux Pull cpupower utility updates for v5.8-rc1 from Shuah Khan: "This cpupower update for Linux 5.8-rc1 consists of a single patch to fix coccicheck unneeded semicolon warning." * tag 'linux-cpupower-5.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux: cpupower: Remove unneeded semicolon
2020-05-25ieee80211: Fix incorrect mask for default PE durationPradeep Kumar Chitrapu
Fixes bitmask for HE opration's default PE duration. Fixes: daa5b83513a7 ("mac80211: update HE operation fields to D3.0") Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org> Link: https://lore.kernel.org/r/20200506102430.5153-1-pradeepc@codeaurora.org Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-05-25mac80211: mesh: fix discovery timer re-arming issue / crashLinus Lüssing
On a non-forwarding 802.11s link between two fairly busy neighboring nodes (iperf with -P 16 at ~850MBit/s TCP; 1733.3 MBit/s VHT-MCS 9 80MHz short GI VHT-NSS 4), so with frequent PREQ retries, usually after around 30-40 seconds the following crash would occur: [ 1110.822428] Unable to handle kernel read from unreadable memory at virtual address 00000000 [ 1110.830786] Mem abort info: [ 1110.833573] Exception class = IABT (current EL), IL = 32 bits [ 1110.839494] SET = 0, FnV = 0 [ 1110.842546] EA = 0, S1PTW = 0 [ 1110.845678] user pgtable: 4k pages, 48-bit VAs, pgd = ffff800076386000 [ 1110.852204] [0000000000000000] *pgd=00000000f6322003, *pud=00000000f62de003, *pmd=0000000000000000 [ 1110.861167] Internal error: Oops: 86000004 [#1] PREEMPT SMP [ 1110.866730] Modules linked in: pppoe ppp_async batman_adv ath10k_pci ath10k_core ath pppox ppp_generic nf_conntrack_ipv6 mac80211 iptable_nat ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_nat xt_multiport xt_mark xt_mac xt_limit xt_conntrack xt_comment xt_TCPMSS xt_REDIRECT xt_LOG xt_FLOWOFFLOAD slhc nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_conntrack_ipv4 nf_nat_ipv4 nf_nat nf_log_ipv4 nf_flow_table_hw nf_flow_table nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack iptable_mangle iptable_filter ip_tables crc_ccitt compat nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 usb_storage xhci_plat_hcd xhci_pci xhci_hcd dwc3 usbcore usb_common [ 1110.932190] Process swapper/3 (pid: 0, stack limit = 0xffff0000090c8000) [ 1110.938884] CPU: 3 PID: 0 Comm: swapper/3 Not tainted 4.14.162 #0 [ 1110.944965] Hardware name: LS1043A RGW Board (DT) [ 1110.949658] task: ffff8000787a81c0 task.stack: ffff0000090c8000 [ 1110.955568] PC is at 0x0 [ 1110.958097] LR is at call_timer_fn.isra.27+0x24/0x78 [ 1110.963055] pc : [<0000000000000000>] lr : [<ffff0000080ff29c>] pstate: 00400145 [ 1110.970440] sp : ffff00000801be10 [ 1110.973744] x29: ffff00000801be10 x28: ffff000008bf7018 [ 1110.979047] x27: ffff000008bf87c8 x26: ffff000008c160c0 [ 1110.984352] x25: 0000000000000000 x24: 0000000000000000 [ 1110.989657] x23: dead000000000200 x22: 0000000000000000 [ 1110.994959] x21: 0000000000000000 x20: 0000000000000101 [ 1111.000262] x19: ffff8000787a81c0 x18: 0000000000000000 [ 1111.005565] x17: ffff0000089167b0 x16: 0000000000000058 [ 1111.010868] x15: ffff0000089167b0 x14: 0000000000000000 [ 1111.016172] x13: ffff000008916788 x12: 0000000000000040 [ 1111.021475] x11: ffff80007fda9af0 x10: 0000000000000001 [ 1111.026777] x9 : ffff00000801bea0 x8 : 0000000000000004 [ 1111.032080] x7 : 0000000000000000 x6 : ffff80007fda9aa8 [ 1111.037383] x5 : ffff00000801bea0 x4 : 0000000000000010 [ 1111.042685] x3 : ffff00000801be98 x2 : 0000000000000614 [ 1111.047988] x1 : 0000000000000000 x0 : 0000000000000000 [ 1111.053290] Call trace: [ 1111.055728] Exception stack(0xffff00000801bcd0 to 0xffff00000801be10) [ 1111.062158] bcc0: 0000000000000000 0000000000000000 [ 1111.069978] bce0: 0000000000000614 ffff00000801be98 0000000000000010 ffff00000801bea0 [ 1111.077798] bd00: ffff80007fda9aa8 0000000000000000 0000000000000004 ffff00000801bea0 [ 1111.085618] bd20: 0000000000000001 ffff80007fda9af0 0000000000000040 ffff000008916788 [ 1111.093437] bd40: 0000000000000000 ffff0000089167b0 0000000000000058 ffff0000089167b0 [ 1111.101256] bd60: 0000000000000000 ffff8000787a81c0 0000000000000101 0000000000000000 [ 1111.109075] bd80: 0000000000000000 dead000000000200 0000000000000000 0000000000000000 [ 1111.116895] bda0: ffff000008c160c0 ffff000008bf87c8 ffff000008bf7018 ffff00000801be10 [ 1111.124715] bdc0: ffff0000080ff29c ffff00000801be10 0000000000000000 0000000000400145 [ 1111.132534] bde0: ffff8000787a81c0 ffff00000801bde8 0000ffffffffffff 000001029eb19be8 [ 1111.140353] be00: ffff00000801be10 0000000000000000 [ 1111.145220] [< (null)>] (null) [ 1111.149917] [<ffff0000080ff77c>] run_timer_softirq+0x184/0x398 [ 1111.155741] [<ffff000008081938>] __do_softirq+0x100/0x1fc [ 1111.161130] [<ffff0000080a2e28>] irq_exit+0x80/0xd8 [ 1111.166002] [<ffff0000080ea708>] __handle_domain_irq+0x88/0xb0 [ 1111.171825] [<ffff000008081678>] gic_handle_irq+0x68/0xb0 [ 1111.177213] Exception stack(0xffff0000090cbe30 to 0xffff0000090cbf70) [ 1111.183642] be20: 0000000000000020 0000000000000000 [ 1111.191461] be40: 0000000000000001 0000000000000000 00008000771af000 0000000000000000 [ 1111.199281] be60: ffff000008c95180 0000000000000000 ffff000008c19360 ffff0000090cbef0 [ 1111.207101] be80: 0000000000000810 0000000000000400 0000000000000098 ffff000000000000 [ 1111.214920] bea0: 0000000000000001 ffff0000089167b0 0000000000000000 ffff0000089167b0 [ 1111.222740] bec0: 0000000000000000 ffff000008c198e8 ffff000008bf7018 ffff000008c19000 [ 1111.230559] bee0: 0000000000000000 0000000000000000 ffff8000787a81c0 ffff000008018000 [ 1111.238380] bf00: ffff00000801c000 ffff00000913ba34 ffff8000787a81c0 ffff0000090cbf70 [ 1111.246199] bf20: ffff0000080857cc ffff0000090cbf70 ffff0000080857d0 0000000000400145 [ 1111.254020] bf40: ffff000008018000 ffff00000801c000 ffffffffffffffff ffff0000080fa574 [ 1111.261838] bf60: ffff0000090cbf70 ffff0000080857d0 [ 1111.266706] [<ffff0000080832e8>] el1_irq+0xe8/0x18c [ 1111.271576] [<ffff0000080857d0>] arch_cpu_idle+0x10/0x18 [ 1111.276880] [<ffff0000080d7de4>] do_idle+0xec/0x1b8 [ 1111.281748] [<ffff0000080d8020>] cpu_startup_entry+0x20/0x28 [ 1111.287399] [<ffff00000808f81c>] secondary_start_kernel+0x104/0x110 [ 1111.293662] Code: bad PC value [ 1111.296710] ---[ end trace 555b6ca4363c3edd ]--- [ 1111.301318] Kernel panic - not syncing: Fatal exception in interrupt [ 1111.307661] SMP: stopping secondary CPUs [ 1111.311574] Kernel Offset: disabled [ 1111.315053] CPU features: 0x0002000 [ 1111.318530] Memory Limit: none [ 1111.321575] Rebooting in 3 seconds.. With some added debug output / delays we were able to push the crash from the timer callback runner into the callback function and by that shedding some light on which object holding the timer gets corrupted: [ 401.720899] Unable to handle kernel read from unreadable memory at virtual address 00000868 [...] [ 402.335836] [<ffff0000088fafa4>] _raw_spin_lock_bh+0x14/0x48 [ 402.341548] [<ffff000000dbe684>] mesh_path_timer+0x10c/0x248 [mac80211] [ 402.348154] [<ffff0000080ff29c>] call_timer_fn.isra.27+0x24/0x78 [ 402.354150] [<ffff0000080ff77c>] run_timer_softirq+0x184/0x398 [ 402.359974] [<ffff000008081938>] __do_softirq+0x100/0x1fc [ 402.365362] [<ffff0000080a2e28>] irq_exit+0x80/0xd8 [ 402.370231] [<ffff0000080ea708>] __handle_domain_irq+0x88/0xb0 [ 402.376053] [<ffff000008081678>] gic_handle_irq+0x68/0xb0 The issue happens due to the following sequence of events: 1) mesh_path_start_discovery(): -> spin_unlock_bh(&mpath->state_lock) before mesh_path_sel_frame_tx() 2) mesh_path_free_rcu() -> del_timer_sync(&mpath->timer) [...] -> kfree_rcu(mpath) 3) mesh_path_start_discovery(): -> mod_timer(&mpath->timer, ...) [...] -> rcu_read_unlock() 4) mesh_path_free_rcu()'s kfree_rcu(): -> kfree(mpath) 5) mesh_path_timer() starts after timeout, using freed mpath object So a use-after-free issue due to a timer re-arming bug caused by an early spin-unlocking. This patch fixes this issue by re-checking if mpath is about to be free'd and if so bails out of re-arming the timer. Cc: stable@vger.kernel.org Fixes: 050ac52cbe1f ("mac80211: code for on-demand Hybrid Wireless Mesh Protocol") Cc: Simon Wunderlich <sw@simonwunderlich.de> Signed-off-by: Linus Lüssing <ll@simonwunderlich.de> Link: https://lore.kernel.org/r/20200522170413.14973-1-linus.luessing@c0d3.blue Signed-off-by: Johannes Berg <johannes.berg@intel.com>
2020-05-25media: dvb-usb: Add Cinergy S2 PCIe Dual Port supportDirk Nehring
Terratec Cinergy S2 PCIe Dual is a PCIe device with two tuners that actually contains two USB devices. The devices are visible in the lsusb printout. Bus 004 Device 002: ID 153b:1182 TerraTec Electronic GmbH Cinergy S2 PCIe Dual Port 2 Bus 003 Device 002: ID 153b:1181 TerraTec Electronic GmbH Cinergy S2 PCIe Dual Port 1 The devices use the Montage M88DS3000/M88TS2022 demod/tuner. Signed-off-by: Dirk Nehring <dnehring@gmx.net> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-05-25media: dvbdev: Fix tuner->demod media controller linkBrad Love
Fixes bug exposed by: [a3fbc2e6bb0: media: mc-entity.c: use WARN_ON, validate link pads] The dvbdev incorrectly requests a tuner sink pad to connect to a demux sink pad. The media controller failure percolates back and the dvb device creation fails. Fix this by requesting a tuner source pad. Instead of forcing that pad to be index zero, check if a negative integer error is returned. A note is added that first source pad found is chosen. Affected bridges cx231xx and em28xx printed the below warning[s] when a variety of media controller dvb enabled devices were connected. The warning returns an error causing all affected devices to fail DVB device creation. [ 253.138332] ------------[ cut here ]------------ [ 253.138339] WARNING: CPU: 0 PID: 1550 at drivers/media/mc/mc-entity.c:669 media_create_pad_link+0x1e0/0x200 [mc] [ 253.138339] Modules linked in: si2168 em28xx_dvb(+) em28xx si2157 lgdt3306a cx231xx_dvb dvb_core cx231xx_alsa cx25840 cx231xx tveeprom cx2341x i2c_mux videobuf2_vmalloc videobuf2_memops videobuf2_v4l2 videobuf2_common videodev mc ir_rc5_decoder rc_hauppauge mceusb rc_core eda c_mce_amd kvm nls_iso8859_1 crct10dif_pclmul crc32_pclmul ghash_clmulni_intel aesni_intel crypto_simd cryptd glue_helper efi_pstore wmi_bmof k10temp asix usbnet mii nouveau snd_hda_codec_realtek snd_hda_codec_generic input_leds ledtrig_audio snd_hda_codec_hdmi mxm_wmi snd_hda_in tel video snd_intel_dspcfg ttm snd_hda_codec drm_kms_helper snd_hda_core drm snd_hwdep snd_seq_midi snd_seq_midi_event i2c_algo_bit snd_pcm snd_rawmidi fb_sys_fops snd_seq syscopyarea sysfillrect snd_seq_device sysimgblt snd_timer snd soundcore ccp mac_hid sch_fq_codel parport_p c ppdev lp parport ip_tables x_tables autofs4 vfio_pci irqbypass vfio_virqfd vfio_iommu_type1 vfio hid_generic usbhid hid i2c_piix4 ahci libahci wmi gpio_amdpt [ 253.138370] gpio_generic [ 253.138372] CPU: 0 PID: 1550 Comm: modprobe Tainted: G W 5.7.0-rc2+ #181 [ 253.138373] Hardware name: MSI MS-7A39/B350M GAMING PRO (MS-7A39), BIOS 2.G0 04/27/2018 [ 253.138376] RIP: 0010:media_create_pad_link+0x1e0/0x200 [mc] [ 253.138378] Code: 26 fd ff ff 44 8b 4d d0 eb d9 0f 0b 41 b9 ea ff ff ff 44 89 c8 c3 0f 0b 41 b9 ea ff ff ff eb f2 0f 0b 41 b9 ea ff ff ff eb e8 <0f> 0b 41 b9 ea ff ff ff eb af 0f 0b 41 b9 ea ff ff ff eb a5 66 90 [ 253.138379] RSP: 0018:ffffb9ecc0ee7a78 EFLAGS: 00010246 [ 253.138380] RAX: ffff943f706c99d8 RBX: 0000000000000000 RCX: 0000000000000000 [ 253.138381] RDX: ffff943f613e0180 RSI: 0000000000000000 RDI: ffff943f706c9958 [ 253.138381] RBP: ffffb9ecc0ee7ab0 R08: 0000000000000001 R09: ffff943f613e0180 [ 253.138382] R10: ffff943f613e0180 R11: ffff943f706c9400 R12: 0000000000000000 [ 253.138383] R13: 0000000000000001 R14: ffff943f706c9958 R15: 0000000000000001 [ 253.138384] FS: 00007f3cd29ba540(0000) GS:ffff943f8ec00000(0000) knlGS:0000000000000000 [ 253.138385] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 253.138385] CR2: 000055f7de0ca830 CR3: 00000003dd208000 CR4: 00000000003406f0 [ 253.138386] Call Trace: [ 253.138392] media_create_pad_links+0x104/0x1b0 [mc] [ 253.138397] dvb_create_media_graph+0x350/0x5f0 [dvb_core] [ 253.138402] em28xx_dvb_init+0x5ea/0x2600 [em28xx_dvb] [ 253.138408] em28xx_register_extension+0x63/0xc0 [em28xx] [ 253.138410] ? 0xffffffffc039c000 [ 253.138412] em28xx_dvb_register+0x15/0x1000 [em28xx_dvb] [ 253.138416] do_one_initcall+0x71/0x250 [ 253.138418] ? do_init_module+0x27/0x22e [ 253.138421] ? _cond_resched+0x1a/0x50 [ 253.138423] ? kmem_cache_alloc_trace+0x1ec/0x270 [ 253.138425] ? __vunmap+0x1e3/0x240 [ 253.138427] do_init_module+0x5f/0x22e [ 253.138430] load_module+0x2525/0x2d40 [ 253.138436] __do_sys_finit_module+0xe5/0x120 [ 253.138438] ? __do_sys_finit_module+0xe5/0x120 [ 253.138442] __x64_sys_finit_module+0x1a/0x20 [ 253.138443] do_syscall_64+0x57/0x1b0 [ 253.138445] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 253.138446] RIP: 0033:0x7f3cd24dc839 [ 253.138448] Code: 00 f3 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 1f f6 2c 00 f7 d8 64 89 01 48 [ 253.138449] RSP: 002b:00007ffe4fc514d8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139 [ 253.138450] RAX: ffffffffffffffda RBX: 000055a9237f63f0 RCX: 00007f3cd24dc839 [ 253.138451] RDX: 0000000000000000 RSI: 000055a922c3ad2e RDI: 0000000000000000 [ 253.138451] RBP: 000055a922c3ad2e R08: 0000000000000000 R09: 0000000000000000 [ 253.138452] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000000 [ 253.138453] R13: 000055a9237f5550 R14: 0000000000040000 R15: 000055a9237f63f0 [ 253.138456] ---[ end trace a60f19c54aa96ec4 ]--- [ 234.915628] ------------[ cut here ]------------ [ 234.915640] WARNING: CPU: 0 PID: 1502 at drivers/media/mc/mc-entity.c:669 media_create_pad_link+0x1e0/0x200 [mc] [ 234.915641] Modules linked in: si2157 lgdt3306a cx231xx_dvb(+) dvb_core cx231xx_alsa cx25840 cx231xx tveeprom cx2341x i2c_mux videobuf2_vmalloc videobuf2_memops videobuf2_v4l2 videobuf2_common videodev mc ir_rc5_decoder rc_hauppauge mceusb rc_core edac_mce_amd kvm nls_iso8859 _1 crct10dif_pclmul crc32_pclmul ghash_clmulni_intel aesni_intel crypto_simd cryptd glue_helper efi_pstore wmi_bmof k10temp asix usbnet mii nouveau snd_hda_codec_realtek snd_hda_codec_generic input_leds ledtrig_audio snd_hda_codec_hdmi mxm_wmi snd_hda_intel video snd_intel_dspcf g ttm snd_hda_codec drm_kms_helper snd_hda_core drm snd_hwdep snd_seq_midi snd_seq_midi_event i2c_algo_bit snd_pcm snd_rawmidi fb_sys_fops snd_seq syscopyarea sysfillrect snd_seq_device sysimgblt snd_timer snd soundcore ccp mac_hid sch_fq_codel parport_pc ppdev lp parport ip_tab les x_tables autofs4 vfio_pci irqbypass vfio_virqfd vfio_iommu_type1 vfio hid_generic usbhid hid i2c_piix4 ahci libahci wmi gpio_amdpt gpio_generic [ 234.915700] CPU: 0 PID: 1502 Comm: modprobe Not tainted 5.7.0-rc2+ #181 [ 234.915702] Hardware name: MSI MS-7A39/B350M GAMING PRO (MS-7A39), BIOS 2.G0 04/27/2018 [ 234.915709] RIP: 0010:media_create_pad_link+0x1e0/0x200 [mc] [ 234.915712] Code: 26 fd ff ff 44 8b 4d d0 eb d9 0f 0b 41 b9 ea ff ff ff 44 89 c8 c3 0f 0b 41 b9 ea ff ff ff eb f2 0f 0b 41 b9 ea ff ff ff eb e8 <0f> 0b 41 b9 ea ff ff ff eb af 0f 0b 41 b9 ea ff ff ff eb a5 66 90 [ 234.915714] RSP: 0018:ffffb9ecc1b6fa50 EFLAGS: 00010246 [ 234.915717] RAX: ffff943f8c94a9d8 RBX: 0000000000000000 RCX: 0000000000000000 [ 234.915719] RDX: ffff943f613e0900 RSI: 0000000000000000 RDI: ffff943f8c94a958 [ 234.915721] RBP: ffffb9ecc1b6fa88 R08: 0000000000000001 R09: ffff943f613e0900 [ 234.915723] R10: ffff943f613e0900 R11: ffff943f6b590c00 R12: 0000000000000000 [ 234.915724] R13: 0000000000000001 R14: ffff943f8c94a958 R15: 0000000000000001 [ 234.915727] FS: 00007f4ca3646540(0000) GS:ffff943f8ec00000(0000) knlGS:0000000000000000 [ 234.915729] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 234.915731] CR2: 00007fff7a53ba18 CR3: 00000003da614000 CR4: 00000000003406f0 [ 234.915733] Call Trace: [ 234.915745] media_create_pad_links+0x104/0x1b0 [mc] [ 234.915756] dvb_create_media_graph+0x350/0x5f0 [dvb_core] [ 234.915766] dvb_init.part.4+0x691/0x1360 [cx231xx_dvb] [ 234.915780] dvb_init+0x1a/0x20 [cx231xx_dvb] [ 234.915787] cx231xx_register_extension+0x71/0xa0 [cx231xx] [ 234.915791] ? 0xffffffffc042f000 [ 234.915796] cx231xx_dvb_register+0x15/0x1000 [cx231xx_dvb] [ 234.915802] do_one_initcall+0x71/0x250 [ 234.915807] ? do_init_module+0x27/0x22e [ 234.915811] ? _cond_resched+0x1a/0x50 [ 234.915816] ? kmem_cache_alloc_trace+0x1ec/0x270 [ 234.915820] ? __vunmap+0x1e3/0x240 [ 234.915826] do_init_module+0x5f/0x22e [ 234.915831] load_module+0x2525/0x2d40 [ 234.915848] __do_sys_finit_module+0xe5/0x120 [ 234.915850] ? __do_sys_finit_module+0xe5/0x120 [ 234.915862] __x64_sys_finit_module+0x1a/0x20 [ 234.915865] do_syscall_64+0x57/0x1b0 [ 234.915870] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 234.915872] RIP: 0033:0x7f4ca3168839 [ 234.915876] Code: 00 f3 c3 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 8b 0d 1f f6 2c 00 f7 d8 64 89 01 48 [ 234.915878] RSP: 002b:00007ffcea3db3b8 EFLAGS: 00000246 ORIG_RAX: 0000000000000139 [ 234.915881] RAX: ffffffffffffffda RBX: 000055af22c29340 RCX: 00007f4ca3168839 [ 234.915882] RDX: 0000000000000000 RSI: 000055af22c38390 RDI: 0000000000000001 [ 234.915884] RBP: 000055af22c38390 R08: 0000000000000000 R09: 0000000000000000 [ 234.915885] R10: 0000000000000001 R11: 0000000000000246 R12: 0000000000000000 [ 234.915887] R13: 000055af22c29060 R14: 0000000000040000 R15: 0000000000000000 [ 234.915896] ---[ end trace a60f19c54aa96ec3 ]--- Signed-off-by: Brad Love <brad@nextdimension.cc> Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sean Young <sean@mess.org> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
2020-05-25sched/core: Offload wakee task activation if it the wakee is deschedulingMel Gorman
The previous commit: c6e7bd7afaeb: ("sched/core: Optimize ttwu() spinning on p->on_cpu") avoids spinning on p->on_rq when the task is descheduling, but only if the wakee is on a CPU that does not share cache with the waker. This patch offloads the activation of the wakee to the CPU that is about to go idle if the task is the only one on the runqueue. This potentially allows the waker task to continue making progress when the wakeup is not strictly synchronous. This is very obvious with netperf UDP_STREAM running on localhost. The waker is sending packets as quickly as possible without waiting for any reply. It frequently wakes the server for the processing of packets and when netserver is using local memory, it quickly completes the processing and goes back to idle. The waker often observes that netserver is on_rq and spins excessively leading to a drop in throughput. This is a comparison of 5.7-rc6 against "sched: Optimize ttwu() spinning on p->on_cpu" and against this patch labeled vanilla, optttwu-v1r1 and localwakelist-v1r2 respectively. 5.7.0-rc6 5.7.0-rc6 5.7.0-rc6 vanilla optttwu-v1r1 localwakelist-v1r2 Hmean send-64 251.49 ( 0.00%) 258.05 * 2.61%* 305.59 * 21.51%* Hmean send-128 497.86 ( 0.00%) 519.89 * 4.43%* 600.25 * 20.57%* Hmean send-256 944.90 ( 0.00%) 997.45 * 5.56%* 1140.19 * 20.67%* Hmean send-1024 3779.03 ( 0.00%) 3859.18 * 2.12%* 4518.19 * 19.56%* Hmean send-2048 7030.81 ( 0.00%) 7315.99 * 4.06%* 8683.01 * 23.50%* Hmean send-3312 10847.44 ( 0.00%) 11149.43 * 2.78%* 12896.71 * 18.89%* Hmean send-4096 13436.19 ( 0.00%) 13614.09 ( 1.32%) 15041.09 * 11.94%* Hmean send-8192 22624.49 ( 0.00%) 23265.32 * 2.83%* 24534.96 * 8.44%* Hmean send-16384 34441.87 ( 0.00%) 36457.15 * 5.85%* 35986.21 * 4.48%* Note that this benefit is not universal to all wakeups, it only applies to the case where the waker often spins on p->on_rq. The impact can be seen from a "perf sched latency" report generated from a single iteration of one packet size: ----------------------------------------------------------------------------------------------------------------- Task | Runtime ms | Switches | Average delay ms | Maximum delay ms | Maximum delay at | ----------------------------------------------------------------------------------------------------------------- vanilla netperf:4337 | 21709.193 ms | 2932 | avg: 0.002 ms | max: 0.041 ms | max at: 112.154512 s netserver:4338 | 14629.459 ms | 5146990 | avg: 0.001 ms | max: 1615.864 ms | max at: 140.134496 s localwakelist-v1r2 netperf:4339 | 29789.717 ms | 2460 | avg: 0.002 ms | max: 0.059 ms | max at: 138.205389 s netserver:4340 | 18858.767 ms | 7279005 | avg: 0.001 ms | max: 0.362 ms | max at: 135.709683 s ----------------------------------------------------------------------------------------------------------------- Note that the average wakeup delay is quite small on both the vanilla kernel and with the two patches applied. However, there are significant outliers with the vanilla kernel with the maximum one measured as 1615 milliseconds with a vanilla kernel but never worse than 0.362 ms with both patches applied and a much higher rate of context switching. Similarly a separate profile of cycles showed that 2.83% of all cycles were spent in try_to_wake_up() with almost half of the cycles spent on spinning on p->on_rq. With the two patches, the percentage of cycles spent in try_to_wake_up() drops to 1.13% Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Jirka Hladky <jhladky@redhat.com> Cc: Vincent Guittot <vincent.guittot@linaro.org> Cc: valentin.schneider@arm.com Cc: Hillf Danton <hdanton@sina.com> Cc: Rik van Riel <riel@surriel.com> Link: https://lore.kernel.org/r/20200524202956.27665-3-mgorman@techsingularity.net
2020-05-25sched/core: Optimize ttwu() spinning on p->on_cpuPeter Zijlstra
Both Rik and Mel reported seeing ttwu() spend significant time on: smp_cond_load_acquire(&p->on_cpu, !VAL); Attempt to avoid this by queueing the wakeup on the CPU that owns the p->on_cpu value. This will then allow the ttwu() to complete without further waiting. Since we run schedule() with interrupts disabled, the IPI is guaranteed to happen after p->on_cpu is cleared, this is what makes it safe to queue early. Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org> Signed-off-by: Mel Gorman <mgorman@techsingularity.net> Signed-off-by: Ingo Molnar <mingo@kernel.org> Cc: Jirka Hladky <jhladky@redhat.com> Cc: Vincent Guittot <vincent.guittot@linaro.org> Cc: valentin.schneider@arm.com Cc: Hillf Danton <hdanton@sina.com> Cc: Rik van Riel <riel@surriel.com> Link: https://lore.kernel.org/r/20200524202956.27665-2-mgorman@techsingularity.net
2020-05-24vxlan: Do not assume RTNL is held in vxlan_fdb_info()Ido Schimmel
vxlan_fdb_info() is not always called with RTNL held or from an RCU read-side critical section. For example, in the following call path: vxlan_cleanup() vxlan_fdb_destroy() vxlan_fdb_notify() __vxlan_fdb_notify() vxlan_fdb_info() The use of rtnl_dereference() can therefore result in the following splat [1]. Fix this by dereferencing the nexthop under RCU read-side critical section. [1] [May24 22:56] ============================= [ +0.004676] WARNING: suspicious RCU usage [ +0.004614] 5.7.0-rc5-custom-16219-g201392003491 #2772 Not tainted [ +0.007116] ----------------------------- [ +0.004657] drivers/net/vxlan.c:276 suspicious rcu_dereference_check() usage! [ +0.008164] other info that might help us debug this: [ +0.009126] rcu_scheduler_active = 2, debug_locks = 1 [ +0.007504] 5 locks held by bash/6892: [ +0.004392] #0: ffff8881d47e3410 (&sig->cred_guard_mutex){+.+.}-{3:3}, at: __do_execve_file.isra.27+0x392/0x23c0 [ +0.011795] #1: ffff8881d47e34b0 (&sig->exec_update_mutex){+.+.}-{3:3}, at: flush_old_exec+0x510/0x2030 [ +0.010947] #2: ffff8881a141b0b0 (ptlock_ptr(page)#2){+.+.}-{2:2}, at: unmap_page_range+0x9c0/0x2590 [ +0.010585] #3: ffff888230009d50 ((&vxlan->age_timer)){+.-.}-{0:0}, at: call_timer_fn+0xe8/0x800 [ +0.010192] #4: ffff888183729bc8 (&vxlan->hash_lock[h]){+.-.}-{2:2}, at: vxlan_cleanup+0x133/0x4a0 [ +0.010382] stack backtrace: [ +0.005103] CPU: 1 PID: 6892 Comm: bash Not tainted 5.7.0-rc5-custom-16219-g201392003491 #2772 [ +0.009675] Hardware name: Mellanox Technologies Ltd. MSN2100-CB2FO/SA001017, BIOS 5.6.5 06/07/2016 [ +0.010155] Call Trace: [ +0.002775] <IRQ> [ +0.002313] dump_stack+0xfd/0x178 [ +0.003895] lockdep_rcu_suspicious+0x14a/0x153 [ +0.005157] vxlan_fdb_info+0xe39/0x12a0 [ +0.004775] __vxlan_fdb_notify+0xb8/0x160 [ +0.004672] vxlan_fdb_notify+0x8e/0xe0 [ +0.004370] vxlan_fdb_destroy+0x117/0x330 [ +0.004662] vxlan_cleanup+0x1aa/0x4a0 [ +0.004329] call_timer_fn+0x1c4/0x800 [ +0.004357] run_timer_softirq+0x129d/0x17e0 [ +0.004762] __do_softirq+0x24c/0xaef [ +0.004232] irq_exit+0x167/0x190 [ +0.003767] smp_apic_timer_interrupt+0x1dd/0x6a0 [ +0.005340] apic_timer_interrupt+0xf/0x20 [ +0.004620] </IRQ> Fixes: 1274e1cc4226 ("vxlan: ecmp support for mac fdb entries") Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reported-by: Amit Cohen <amitc@mellanox.com> Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-24Merge branch 'mlxsw-Various-trap-changes-part-1'David S. Miller
Ido Schimmel says: ==================== mlxsw: Various trap changes - part 1 This patch set contains various changes in mlxsw trap configuration. Another set will perform similar changes before exposing control traps (e.g., IGMP query, ARP request) via devlink-trap. Tested with existing devlink-trap selftests. Please see individual patches for a detailed changelog. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-24mlxsw: spectrum: Fix spelling mistake in trap's nameIdo Schimmel
Fix incorrect spelling of "advertisement". Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-24mlxsw: spectrum: Use dedicated trap group for sampled packetsIdo Schimmel
The rate with which packets are sampled is determined by user space, so there is no need to associate such packets with a policer. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-24mlxsw: spectrum: Use same trap group for IPv6 ND and ARP packetsIdo Schimmel
Both packet types are needed for the same reason (neighbour discovery), so associate them with the same trap group. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-24mlxsw: spectrum: Rename ARP trap groupIdo Schimmel
The ARP trap group will be used for IPv6 ND traps in the next patch, so rename it to "NEIGH_DISCOVERY" which is more appropriate. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-24mlxsw: spectrum_trap: Remove unnecessary fieldIdo Schimmel
Now that traffic class (TC) and priority are set to the same value, there is no need to store both. Remove the first. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-24mlxsw: spectrum: Align TC and trap priorityIdo Schimmel
The traffic class (TC) attribute of packet traps determines through which TC a packet trap will be scheduled through the CPU port. The priority attribute determines which trap will be triggered in case several packet traps match a packet. We try to configure these attributes to the same value for all packet traps as there is little reason not to. Some packet traps did not use the same value, so rectify that now. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-24mlxsw: spectrum_buffers: Assign non-zero quotas to TC 0 of the CPU portIdo Schimmel
As explained in commit 9ffcc3725f09 ("mlxsw: spectrum: Allow packets to be trapped from any PG"), incoming packets can be admitted to the shared buffer and forwarded / trapped, if: (Ingress{Port}.Usage < Thres && Ingress{Port,PG}.Usage < Thres && Egress{Port}.Usage < Thres && Egress{Port,TC}.Usage < Thres) || (Ingress{Port}.Usage < Min || Ingress{Port,PG} < Min || Egress{Port}.Usage < Min || Egress{Port,TC}.Usage < Min) Trapped packets are scheduled to transmission through the CPU port. Currently, the minimum and maximum quotas of traffic class (TC) 0 of the CPU port are 0, which means it is not usable. Assign non-zero quotas to TC 0 of the CPU port, so that it could be utilized by subsequent patches. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-24mlxsw: spectrum: Change default rate and priority of DHCP packetsIdo Schimmel
Reduce the default acceptable rate of DHCP packets to 128 packets per second and reduce their priority. This is reasonable given the Spectrum ASICs are limited to 128 ports at the moment. These are only the default values. Users will be able to modify them via devlink-trap. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-24mlxsw: spectrum: Trap IPv4 DHCP packets in routerIdo Schimmel
Currently, IPv4 DHCP packets are trapped during L2 forwarding, which means that packets might be trapped unnecessarily. Instead, only trap the DHCP packets that reach the router. Either because they were flooded to the router port or forwarded to it by the FDB. This is consistent with the corresponding IPv6 trap. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-24mlxsw: spectrum: Use same trap group for MLD and IGMP packetsIdo Schimmel
Both packet types are needed for the same reason (multicast snooping), so associate them with the same trap group. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-24mlxsw: spectrum: Rename IGMP trap groupIdo Schimmel
The IGMP trap group will be used for MLD traps in the next patch, so rename it to "MC_SNOOPING" which is more appropriate. Signed-off-by: Ido Schimmel <idosch@mellanox.com> Reviewed-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-24Linux 5.7-rc7v5.7-rc7Linus Torvalds
2020-05-24Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller
The MSCC bug fix in 'net' had to be slightly adjusted because the register accesses are done slightly differently in net-next. Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-24Merge tag 'efi-urgent-2020-05-24' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull EFI fixes from Thomas Gleixner: "A set of EFI fixes: - Don't return a garbage screen info when EFI framebuffer is not available - Make the early EFI console work properly with wider fonts instead of drawing garbage - Prevent a memory buffer leak in allocate_e820() - Print the firmware error record properly so it can be decoded by users - Fix a symbol clash in the host tool build which only happens with newer compilers. - Add a missing check for the event log version of TPM which caused boot failures on several Dell systems due to an attempt to decode SHA-1 format with the crypto agile algorithm" * tag 'efi-urgent-2020-05-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: tpm: check event log version before reading final events efi: Pull up arch-specific prototype efi_systab_show_arch() x86/boot: Mark global variables as static efi: cper: Add support for printing Firmware Error Record Reference efi/libstub/x86: Avoid EFI map buffer alloc in allocate_e820() efi/earlycon: Fix early printk for wider fonts efi/libstub: Avoid returning uninitialized data from setup_graphics()
2020-05-24Merge tag 'x86-urgent-2020-05-24' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull x86 fixes from Thomas Gleixner: "Two fixes for x86: - Unbreak stack dumps for inactive tasks by interpreting the special first frame left by __switch_to_asm() correctly. The recent change not to skip the first frame so ORC and frame unwinder behave in the same way caused all entries to be unreliable, i.e. prepended with '?'. - Use cpumask_available() instead of an implicit NULL check of a cpumask_var_t in mmio trace to prevent a Clang build warning" * tag 'x86-urgent-2020-05-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: x86/unwind/orc: Fix unwind_get_return_address_ptr() for inactive tasks x86/mmiotrace: Use cpumask_available() for cpumask_var_t variables
2020-05-24Merge tag 'sched-urgent-2020-05-24' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip Pull scheduler fixes from Thomas Gleixner: "A set of fixes for the scheduler: - Fix handling of throttled parents in enqueue_task_fair() completely. The recent fix overlooked a corner case where the first iteration terminates due to an entity already being on the runqueue which makes the list management incomplete and later triggers the assertion which checks for completeness. - Fix a similar problem in unthrottle_cfs_rq(). - Show the correct uclamp values in procfs which prints the effective value twice instead of requested and effective" * tag 'sched-urgent-2020-05-24' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched/fair: Fix unthrottle_cfs_rq() for leaf_cfs_rq list sched/debug: Fix requested task uclamp values shown in procfs sched/fair: Fix enqueue_task_fair() warning some more
2020-05-24loop: remove redundant assignment to variable errorColin Ian King
The variable error is being assigned a value that is never read so the assignment is redundant and can be removed. Addresses-Coverity: ("Unused value") Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Jens Axboe <axboe@kernel.dk>
2020-05-24MIPS: tools: Fix resource leak in elf-entry.cKaige Li
There is a file descriptor resource leak in elf-entry.c, fix this by adding fclose() before return and die. Signed-off-by: Kaige Li <likaige@loongson.cn> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-05-24MIPS: SGI-IP30: Reorder the macros in war.hJoshua Kinard
Fix the ordering of the macros in arch/mips/mach-ip30/war.h to match those in arch/mips/mach-ip27/war.h. Signed-off-by: Joshua Kinard <kumba@gentoo.org> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-05-24MIPS: emulate CPUCFG instruction on older Loongson64 coresWANG Xuerui
CPUCFG is the instruction for querying processor characteristics on newer Loongson processors, much like CPUID of x86. Since the instruction is supposedly designed to provide a unified way to do feature detection (without having to, for example, parse /proc/cpuinfo which is too heavyweight), it is important to provide compatibility for older cores without native support. Fortunately, most of the fields can be synthesized without changes to semantics. Performance is not really big a concern, because feature detection logic is not expected to be invoked very often in typical userland applications. The instruction can't be emulated on LOONGSON_2EF cores, according to FlyGoat's experiments. Because the LWC2 opcode is assigned to other valid instructions on 2E and 2F, no RI exception is raised for us to intercept. So compatibility is only extended back furthest to Loongson-3A1000. Loongson-2K is covered too, as it is basically a remix of various blocks from the 3A/3B models from a kernel perspective. This is lightly based on Loongson's work on their Linux 3.10 fork, for being the authority on the right feature flags to fill in, where things aren't otherwise discoverable. Signed-off-by: WANG Xuerui <git@xen0n.name> Reviewed-by: Jiaxun Yang <jiaxun.yang@flygoat.com> Cc: Huacai Chen <chenhc@lemote.com> Cc: Jiaxun Yang <jiaxun.yang@flygoat.com> Cc: Tiezhu Yang <yangtiezhu@loongson.cn> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-05-24MIPS: Tidy up CP0.Config6 bits definitionHuacai Chen
CP0.Config6 is a Vendor-defined register whose bits definitions are different from one to another. Recently, Xuerui's Loongson-3 patch and Serge's P5600 patch make the definitions inconsistency and unclear. To make life easy, this patch tidy the definition up: 1, Add a _MTI_ infix for proAptiv/P5600 feature bits; 2, Add a _LOONGSON_ infix for Loongson-3 feature bits; 3, Add bit6/bit7 definition for Loongson-3 which will be used later. All existing users of these macros are updated. Cc: WANG Xuerui <git@xen0n.name> Cc: Serge Semin <Sergey.Semin@baikalelectronics.ru> Signed-off-by: Huacai Chen <chenhc@lemote.com> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-05-24MIPS: DTS: Only build subdir of current platformTiezhu Yang
Add config check in Makefile to only build the subdir of current platform. E.g. without this patch: AR arch/mips/built-in.a AR arch/mips/boot/dts/brcm/built-in.a AR arch/mips/boot/dts/cavium-octeon/built-in.a AR arch/mips/boot/dts/img/built-in.a AR arch/mips/boot/dts/ingenic/built-in.a AR arch/mips/boot/dts/lantiq/built-in.a DTC arch/mips/boot/dts/loongson/loongson3_4core_rs780e.dtb DTB arch/mips/boot/dts/loongson/loongson3_4core_rs780e.dtb.S AS arch/mips/boot/dts/loongson/loongson3_4core_rs780e.dtb.o DTC arch/mips/boot/dts/loongson/loongson3_8core_rs780e.dtb DTB arch/mips/boot/dts/loongson/loongson3_8core_rs780e.dtb.S AS arch/mips/boot/dts/loongson/loongson3_8core_rs780e.dtb.o AR arch/mips/boot/dts/loongson/built-in.a AR arch/mips/boot/dts/mscc/built-in.a AR arch/mips/boot/dts/mti/built-in.a AR arch/mips/boot/dts/netlogic/built-in.a AR arch/mips/boot/dts/ni/built-in.a AR arch/mips/boot/dts/pic32/built-in.a AR arch/mips/boot/dts/qca/built-in.a AR arch/mips/boot/dts/ralink/built-in.a AR arch/mips/boot/dts/xilfpga/built-in.a AR arch/mips/boot/dts/built-in.a With this patch: AR arch/mips/built-in.a DTC arch/mips/boot/dts/loongson/loongson3_4core_rs780e.dtb DTB arch/mips/boot/dts/loongson/loongson3_4core_rs780e.dtb.S AS arch/mips/boot/dts/loongson/loongson3_4core_rs780e.dtb.o DTC arch/mips/boot/dts/loongson/loongson3_8core_rs780e.dtb DTB arch/mips/boot/dts/loongson/loongson3_8core_rs780e.dtb.S AS arch/mips/boot/dts/loongson/loongson3_8core_rs780e.dtb.o AR arch/mips/boot/dts/loongson/built-in.a AR arch/mips/boot/dts/built-in.a Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-05-24MIPS: Fix exception handler memcpy()Ben Hutchings
The exception handler subroutines are declared as a single char, but when copied to the required addresses the copy length is 0x80. When range checks are enabled for memcpy() this results in a build failure, with error messages such as: In file included from arch/mips/mti-malta/malta-init.c:15: In function 'memcpy', inlined from 'mips_nmi_setup' at arch/mips/mti-malta/malta-init.c:98:2: include/linux/string.h:376:4: error: call to '__read_overflow2' declared with attribute error: detected read beyond size of object passed as 2nd parameter 376 | __read_overflow2(); | ^~~~~~~~~~~~~~~~~~ Change the declarations to use type char[]. Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: YunQiang Su <syq@debian.org> Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
2020-05-23Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds
Pull networking fixes from David Miller: 1) Fix RCU warnings in ipv6 multicast router code, from Madhuparna Bhowmik. 2) Nexthop attributes aren't being checked properly because of mis-initialized iterator, from David Ahern. 3) Revert iop_idents_reserve() change as it caused performance regressions and was just working around what is really a UBSAN bug in the compiler. From Yuqi Jin. 4) Read MAC address properly from ROM in bmac driver (double iteration proceeds past end of address array), from Jeremy Kerr. 5) Add Microsoft Surface device IDs to r8152, from Marc Payne. 6) Prevent reference to freed SKB in __netif_receive_skb_core(), from Boris Sukholitko. 7) Fix ACK discard behavior in rxrpc, from David Howells. 8) Preserve flow hash across packet scrubbing in wireguard, from Jason A. Donenfeld. 9) Cap option length properly for SO_BINDTODEVICE in AX25, from Eric Dumazet. 10) Fix encryption error checking in kTLS code, from Vadim Fedorenko. 11) Missing BPF prog ref release in flow dissector, from Jakub Sitnicki. 12) dst_cache must be used with BH disabled in tipc, from Eric Dumazet. 13) Fix use after free in mlxsw driver, from Jiri Pirko. 14) Order kTLS key destruction properly in mlx5 driver, from Tariq Toukan. 15) Check devm_platform_ioremap_resource() return value properly in several drivers, from Tiezhu Yang. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (71 commits) net: smsc911x: Fix runtime PM imbalance on error net/mlx4_core: fix a memory leak bug. net: ethernet: ti: cpsw: fix ASSERT_RTNL() warning during suspend net: phy: mscc: fix initialization of the MACsec protocol mode net: stmmac: don't attach interface until resume finishes net: Fix return value about devm_platform_ioremap_resource() net/mlx5: Fix error flow in case of function_setup failure net/mlx5e: CT: Correctly get flow rule net/mlx5e: Update netdev txq on completions during closure net/mlx5: Annotate mutex destroy for root ns net/mlx5: Don't maintain a case of del_sw_func being null net/mlx5: Fix cleaning unmanaged flow tables net/mlx5: Fix memory leak in mlx5_events_init net/mlx5e: Fix inner tirs handling net/mlx5e: kTLS, Destroy key object after destroying the TIS net/mlx5e: Fix allowed tc redirect merged eswitch offload cases net/mlx5: Avoid processing commands before cmdif is ready net/mlx5: Fix a race when moving command interface to events mode net/mlx5: Add command entry handling completion rxrpc: Fix a memory leak in rxkad_verify_response() ...
2020-05-23ethtool: propagate get_coalesce return valueHeiner Kallweit
get_coalesce returns 0 or ERRNO, but the return value isn't checked. The returned coalesce data may be invalid if an ERRNO is set, therefore better check and propagate the return value. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-23Merge branch 'net-provide-a-devres-variant-of-register_netdev'David S. Miller
Bartosz Golaszewski says: ==================== net: provide a devres variant of register_netdev() Using devres helpers allows to shrink the probing code, avoid memory leaks in error paths make sure the order in which resources are freed is the exact opposite of their allocation. This series proposes to add a devres variant of register_netdev() that will only work with net_device structures whose memory is also managed. First we add the missing documentation entry for the only other networking devres helper: devm_alloc_etherdev(). Next we move devm_alloc_etherdev() into a separate source file. We then use a proxy structure in devm_alloc_etherdev() to improve readability. Last: we implement devm_register_netdev() and use it in mtk-eth-mac driver. v1 -> v2: - rebase on top of net-next after driver rename, no functional changes ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-23net: ethernet: mtk_star_emac: use devm_register_netdev()Bartosz Golaszewski
Use the new devres variant of register_netdev() in the mtk-star-emac driver and shrink the code by a couple lines. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-23net: devres: provide devm_register_netdev()Bartosz Golaszewski
Provide devm_register_netdev() - a device resource managed variant of register_netdev(). This new helper will only work for net_device structs that are also already managed by devres. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-23net: devres: define a separate devres structure for devm_alloc_etherdev()Bartosz Golaszewski
Not using a proxy structure to store struct net_device doesn't save anything in terms of compiled code size or memory usage but significantly decreases the readability of the code with all the pointer casting. Define struct net_device_devres and use it in devm_alloc_etherdev_mqs(). Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-23net: move devres helpers into a separate source fileBartosz Golaszewski
There's currently only a single devres helper in net/ - devm variant of alloc_etherdev. Let's move it to net/devres.c with the intention of assing a second one: devm_register_netdev(). This new routine will need to know the address of the release function of devm_alloc_etherdev() so that it can verify (using devres_find()) that the struct net_device that's being passed to it is also resource managed. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-23Documentation: devres: add a missing section for networking helpersBartosz Golaszewski
Add a new section for networking devres helpers to devres.rst and list the two existing devm functions. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-23Merge branch 'r8169-remove-mask-argument-from-few-ERI-OCP-functions'David S. Miller
Heiner Kallweit says: ==================== r8169: remove mask argument from few ERI/OCP functions Few ERI/OCP functions have a mask argument that isn't needed. Remove it to simplify the functions. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-23r8169: remove mask argument from r8168ep_ocp_readHeiner Kallweit
Remove the mask argument as it's not used by r8168ep_ocp_read(). Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-23r8169: remove mask argument from r8168dp_ocp_readHeiner Kallweit
All callers read the full 32bit value, therefore the mask argument can be removed. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-23r8169: remove mask argument from rtl_w0w1_eriHeiner Kallweit
rtl_eri_read() returns the full 32bit value, therefore there's no benefit in writing back parts of it only. handle it like the vendor driver and write the full 32 bit always. Omitting the mask argument avoids some overhead and makes the code better readable. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-23net: smsc911x: Fix runtime PM imbalance on errorDinghao Liu
Remove runtime PM usage counter decrement when the increment function has not been called to keep the counter balanced. Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit (git 2.34.1) at 2025-09-21 19:29:23 +0000