| Age | Commit message (Collapse) | Author |
|---|
|
Get rid of FORCE_MAX_ZONEORDER which limited allocations to order 8 (= 1MB)
and use the default, which allows for order 10 (= 4MB) allocations.
Given that s390 allows less than the default this caused some memory
allocation problems more or less unique to s390 from time to time.
Note: this was originally introduced with commit 684de39bd795 ("[S390]
Fix IPL from NSS.") in order to support Named Saved Segments, which
could start/end at an arbitrary 1 megabyte boundary and also before
support for sparsemem vmemmmap was enabled.
Since NSS support is gone, but sparsemem vmemmap support is available
this limitation can go away.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Trimming to MAX_ORDER was originally done in order to avoid to set
HOLES_IN_ZONE, which in turn would enable a quite expensive
pfn_valid() check. pfn_valid() however only checks if a struct page
exists for a given pfn.
With sparsemen vmemmap there are always struct pages, since memmaps
are allocated for whole sections. Therefore remove the HOLES_IN_ZONE
comment and the trimming.
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
For non-thinint devices in LPAR, qdio polls an idle Input Queue for a
little while to catch more work. But platform support for thinints has
been around practically _forever_ by now, so this micro-optimization is
seeing 0 actual use. Remove it to reduce the overall complexity of the
hot path.
In the meantime we also grew support for driver-level polling
(eg. NAPI in qeth), so it's quite questionable how useful this would
actually be on current kernels.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The comment is inaccurate, qdio_inbound_q_moved() and/or its callers no
longer get confused by a count of 128 completed SBALs.
Scanning all 128 SBALs at once can improve IRQ reduction (as we now
place the ACK at the right spot), and reduce the amount of processing
needed to handle all completed SBALs.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Old code would only scan up to 127 SBALs at once. So the last statistics
bucket was set aside to count "discovered 127 SBALs with new work"
events.
But nowadays we allow to scan all 128 SBALs for Output Queues, and a
subsequent patch will introduce the same for Input Queues.
So fix up the accounting to use the last bucket only when all 128 SBALs
have been discovered with new work.
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
This corrects the mounting matrix for the BMA254
accelerometer to what makes PostmarketOS actually
orient the screen the right way on this device.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20200719201603.3610389-1-linus.walleij@linaro.org
|
|
The `INSN_CONFIG` comedi instruction with sub-instruction code
`INSN_CONFIG_DIGITAL_TRIG` includes a base channel in `data[3]`. This is
used as a right shift amount for other bitmask values without being
checked. Shift amounts greater than or equal to 32 will result in
undefined behavior. Add code to deal with this.
Fixes: 1e15687ea472 ("staging: comedi: addi_apci_1564: add Change-of-State interrupt subdevice and required functions")
Cc: <stable@vger.kernel.org> #3.17+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20200717145257.112660-4-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The `INSN_CONFIG` comedi instruction with sub-instruction code
`INSN_CONFIG_DIGITAL_TRIG` includes a base channel in `data[3]`. This is
used as a right shift amount for other bitmask values without being
checked. Shift amounts greater than or equal to 32 will result in
undefined behavior. Add code to deal with this, adjusting the checks
for invalid channels so that enabled channel bits that would have been
lost by shifting are also checked for validity. Only channels 0 to 15
are valid.
Fixes: a8c66b684efaf ("staging: comedi: addi_apci_1500: rewrite the subdevice support functions")
Cc: <stable@vger.kernel.org> #4.0+: ef75e14a6c93: staging: comedi: verify array index is correct before using it
Cc: <stable@vger.kernel.org> #4.0+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20200717145257.112660-5-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The `INSN_CONFIG` comedi instruction with sub-instruction code
`INSN_CONFIG_DIGITAL_TRIG` includes a base channel in `data[3]`. This is
used as a right shift amount for other bitmask values without being
checked. Shift amounts greater than or equal to 32 will result in
undefined behavior. Add code to deal with this.
Fixes: 33cdce6293dcc ("staging: comedi: addi_apci_1032: conform to new INSN_CONFIG_DIGITAL_TRIG")
Cc: <stable@vger.kernel.org> #3.8+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20200717145257.112660-3-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
`ni6527_intr_insn_config()` processes `INSN_CONFIG` comedi instructions
for the "interrupt" subdevice. When `data[0]` is
`INSN_CONFIG_DIGITAL_TRIG` it is configuring the digital trigger. When
`data[2]` is `COMEDI_DIGITAL_TRIG_ENABLE_EDGES` it is configuring rising
and falling edge detection for the digital trigger, using a base channel
number (or shift amount) in `data[3]`, a rising edge bitmask in
`data[4]` and falling edge bitmask in `data[5]`.
If the base channel number (shift amount) is greater than or equal to
the number of channels (24) of the digital input subdevice, there are no
changes to the rising and falling edges, so the mask of channels to be
changed can be set to 0, otherwise the mask of channels to be changed,
and the rising and falling edge bitmasks are shifted by the base channel
number before calling `ni6527_set_edge_detection()` to change the
appropriate registers. Unfortunately, the code is comparing the base
channel (shift amount) to the interrupt subdevice's number of channels
(1) instead of the digital input subdevice's number of channels (24).
Fix it by comparing to 32 because all shift amounts for an `unsigned
int` must be less than that and everything from bit 24 upwards is
ignored by `ni6527_set_edge_detection()` anyway.
Fixes: 110f9e687c1a8 ("staging: comedi: ni_6527: support INSN_CONFIG_DIGITAL_TRIG")
Cc: <stable@vger.kernel.org> # 3.17+
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Link: https://lore.kernel.org/r/20200717145257.112660-2-abbotti@mev.co.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://people.freedesktop.org/~gabbayo/linux into char-misc-linus
Oded writes:
This tag contains a single bug fix for 5.8-rc7:
- Check that an index is in valid range before using it to access an
array. The index is received from the user. This is to prevent a
possible out-of-bounds access error.
* tag 'misc-habanalabs-fixes-2020-07-19' of git://people.freedesktop.org/~gabbayo/linux:
habanalabs: prevent possible out-of-bounds array access
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mdf/linux-fpga into char-misc-linus
Moritz writes:
FPGA manager fixes for 5.8
Here are two (late) dfl fixes for the the 5.8 release.
Matthew's fix addresses an issue in the reset of a port.
Xu'x fix addresses a linter warning.
All patches have been reviewed on the mailing list, and have been in the
last few linux-next releases (as part of my fixes branch) without issues.
Signed-off-by: Moritz Fischer <mdf@kernel.org>
* tag 'fpga-late-fixes-for-5.8' of git://git.kernel.org/pub/scm/linux/kernel/git/mdf/linux-fpga:
fpga: dfl: fix bug in port reset handshake
fpga: dfl: pci: reduce the scope of variable 'ret'
|
|
Commit 1019fe2c7280 ("ARM: dts: exynos: Adjust bus related OPPs to the
values correct for Exynos5422 Odroids") changed the parameters of the
OPPs for the FSYS bus. Besides the frequency adjustments, it also removed
the 'shared-opp' property from the OPP table used for FSYS_APB and FSYS
busses.
This revealed that in fact the FSYS bus frequency scaling never worked.
When one OPP table is marked as 'opp-shared', only the first bus which
selects the OPP sets the rate of its clock. Then OPP core assumes that
the other busses have been changed to that OPP and no change to their
clock rates are needed. Thus when FSYS_APB bus, which was registered
first, set the rate for its clock, the OPP core did not change the FSYS
bus clock later.
The mentioned commit removed that behavior, what introduced a regression
on some Odroid XU3 boards. Frequency scaling of the FSYS bus causes
instability of the USB host operation, what can be observed as network
hangs. To restore old behavior, simply disable frequency scaling for the
FSYS bus.
Reported-by: Willy Wolff <willy.mh.wolff.ml@gmail.com>
Fixes: 1019fe2c7280 ("ARM: dts: exynos: Adjust bus related OPPs to the values correct for Exynos5422 Odroids")
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.
Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If neither `\bgnu\.org/license`, nor `\bmozilla\.org/MPL\b`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.
Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Link: https://lore.kernel.org/r/20200719113142.58304-1-grandmaster@al2klimov.de
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
|
|
This patch was applied twice.
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
GPIOP7 is used in the Rainier design to manage the state of a
microcontroller elsewhere in the system but its ball, Y23, is the
driver of the heartbeat LED on the ast2600-evb and the SoC defaults Y23
at power-on to the pulse-train behaviour used to drive the LED. This
causes much confusion for the micro in the Rainier system, so hog the
line as early as possible.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The hub FSI master can access the cfams on two other processors. Reflect
this by adding a second cfam to the first hub description.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Tested-by: Andrew Geissler <geissonator@yahoo.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Rainier uses GPIO B6 as the checkstop GPIO. Define the line-name
so that this GPIO can be found by name.
Signed-off-by: Ben Tyner <ben.tyner@ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The attention handler will monitor the checkstop gpio via the character
device interface so it needs to not be defined.
Signed-off-by: Ben Tyner <ben.tyner@ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Add a reserved memory node for the VGA memory. Add the XDMA engine node,
enable it, and point it's memory region to the VGA memory.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Add a reserved memory node for the VGA memory. Add the XDMA engine node,
enable it, and point it's memory region to the VGA memory.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Add the PCI-E root complex reset, correct the pcie-device property, and
add the Aspeed SCU interrupt controller include.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Correct the pcie-device property, and add the Aspeed SCU interrupt
controller include.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The current pin muxing scheme muxes GPIO_1 pad for USB_OTG_ID
because of which when card is inserted, usb otg is enumerated
and the card is never detected.
[ 64.492645] cfg80211: failed to load regulatory.db
[ 64.492657] imx-sdma 20ec000.sdma: external firmware not found, using ROM firmware
[ 76.343711] ci_hdrc ci_hdrc.0: EHCI Host Controller
[ 76.349742] ci_hdrc ci_hdrc.0: new USB bus registered, assigned bus number 2
[ 76.388862] ci_hdrc ci_hdrc.0: USB 2.0 started, EHCI 1.00
[ 76.396650] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.08
[ 76.405412] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 76.412763] usb usb2: Product: EHCI Host Controller
[ 76.417666] usb usb2: Manufacturer: Linux 5.8.0-rc1-next-20200618 ehci_hcd
[ 76.424623] usb usb2: SerialNumber: ci_hdrc.0
[ 76.431755] hub 2-0:1.0: USB hub found
[ 76.435862] hub 2-0:1.0: 1 port detected
The TRM mentions GPIO_1 pad should be muxed/assigned for card detect
and ENET_RX_ER pad for USB_OTG_ID for proper operation.
This patch fixes pin muxing as per TRM and is tested on a
i.Core 1.5 MX6 DL SOM.
[ 22.449165] mmc0: host does not support reading read-only switch, assuming write-enable
[ 22.459992] mmc0: new high speed SDHC card at address 0001
[ 22.469725] mmcblk0: mmc0:0001 EB1QT 29.8 GiB
[ 22.478856] mmcblk0: p1 p2
Fixes: 6df11287f7c9 ("ARM: dts: imx6q: Add Engicam i.CoreM6 Quad/Dual initial support")
Cc: stable@vger.kernel.org
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add I2C child node for switch watchdog present on SPU3
Signed-off-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
esdhc0 is connected to an eMMC, so it is safe to pass the "no-sdio"/"no-sd"
properties.
esdhc1 is wired to a standard SD socket, so pass the "no-sdio" property.
Signed-off-by: Chris Healy <cphealy@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix value of shunt-resistor property.
The LX2160A-RDB has 500 uOhm shunt for
the INA220, not 1000 uOhm. Unless
it will get wrong power consumption(1/2)
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode") fixed the
phy-mode for fec1, but missed to fix it for the fec2 node.
Fix fec2 to also use "rgmii-id" as the phy-mode.
Cc: <stable@vger.kernel.org>
Fixes: 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode") fixed the
phy-mode for fec1, but missed to fix it for the fec2 node.
Fix fec2 to also use "rgmii-id" as the phy-mode.
Cc: <stable@vger.kernel.org>
Fixes: 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to the AR8035 datasheet:
"When using crystal, the clock is generated internally after power is
stable. For a reliable power on reset, suggest to keep asserting the reset
low long enough (10ms) to ensure the clock is stable and clock-to-reset 1ms
requirement is satisfied."
Pass the 'reset-assert-us' property to describe such requirement.
While at it, use the 'reset-gpios' property inside the the mdio
node instead of the deprecated usage of 'phy-reset-gpios'.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
imx6q-tbs2910 has an Atheros AR8035 Ethernet PHY at address 4.
The AR8035 provides a 125MHz clock to the ENET_REF_CLK i.MX6 pin.
Improve the Ethernet representation by adding an mdio node with such
information.
This fixes an Ethernet regression in U-Boot as U-Boot AR803X driver now
expects the 'qca,clk-out-frequency' property to be passed via
device tree.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Tested-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
According to the AR8031 datasheet:
"When using crystal, clock is generated internally after the power is
stable. In order to get reliable power-on-reset, it is recommended to
keep asserting the reset low signal long enough (10 ms) to ensure the
clock is stable and clock-to-reset (1 ms) requirement is satisfied."
Pass the 'reset-assert-us' property to describe such requirement.
While at it, use the 'reset-gpios' property inside the the mdio
node instead of the deprecated usage of 'phy-reset-gpios'.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
imx6qdl-sabresd has an Atheros AR8031 Ethernet PHY at address 1.
The AR8031 provides a 125MHz clock to the ENET_REF_CLK i.MX6 pin.
Improve the Ethernet representation by adding an mdio node with such
information.
An advantage of adding the mdio node is that the AR8031 initialization
code in the mx6sabresd board file in U-Boot can totally be removed.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Soeren Moch <smoch@web.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add entries for MYiR Tech imx6ULL eval boards.
Signed-off-by: Parthiban Nallathambi <parthiban@linumiz.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add Gateworks System Controller support to Gateworks Ventana boards:
- add dt bindings for GSC mfd driver and hwmon driver for ADC's and
fan controllers.
- add dt bindings for gpio-keys driver for push-button and interrupt events
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
If register_netdevice() is failed, net_device should not be used
because variables are uninitialized or freed.
So, the routine should be stopped immediately.
But, bond_create() doesn't check return value of register_netdevice()
immediately. That will result in a panic because of using uninitialized
or freed memory.
Test commands:
modprobe netdev-notifier-error-inject
echo -22 > /sys/kernel/debug/notifier-error-inject/netdev/\
actions/NETDEV_REGISTER/error
modprobe bonding max_bonds=3
Splat looks like:
[ 375.028492][ T193] general protection fault, probably for non-canonical address 0x6b6b6b6b6b6b6b6b: 0000 [#1] SMP DEBUG_PAGEALLOC PTI
[ 375.033207][ T193] CPU: 2 PID: 193 Comm: kworker/2:2 Not tainted 5.8.0-rc4+ #645
[ 375.036068][ T193] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
[ 375.039673][ T193] Workqueue: events linkwatch_event
[ 375.041557][ T193] RIP: 0010:dev_activate+0x4a/0x340
[ 375.043381][ T193] Code: 40 a8 04 0f 85 db 00 00 00 8b 83 08 04 00 00 85 c0 0f 84 0d 01 00 00 31 d2 89 d0 48 8d 04 40 48 c1 e0 07 48 03 83 00 04 00 00 <48> 8b 48 10 f6 41 10 01 75 08 f0 80 a1 a0 01 00 00 fd 48 89 48 08
[ 375.050267][ T193] RSP: 0018:ffff9f8facfcfdd8 EFLAGS: 00010202
[ 375.052410][ T193] RAX: 6b6b6b6b6b6b6b6b RBX: ffff9f8fae6ea000 RCX: 0000000000000006
[ 375.055178][ T193] RDX: 0000000000000000 RSI: 0000000000000000 RDI: ffff9f8fae6ea000
[ 375.057762][ T193] RBP: ffff9f8fae6ea000 R08: 0000000000000000 R09: 0000000000000000
[ 375.059810][ T193] R10: 0000000000000001 R11: 0000000000000000 R12: ffff9f8facfcfe08
[ 375.061892][ T193] R13: ffffffff883587e0 R14: 0000000000000000 R15: ffff9f8fae6ea580
[ 375.063931][ T193] FS: 0000000000000000(0000) GS:ffff9f8fbae00000(0000) knlGS:0000000000000000
[ 375.066239][ T193] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 375.067841][ T193] CR2: 00007f2f542167a0 CR3: 000000012cee6002 CR4: 00000000003606e0
[ 375.069657][ T193] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 375.071471][ T193] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 375.073269][ T193] Call Trace:
[ 375.074005][ T193] linkwatch_do_dev+0x4d/0x50
[ 375.075052][ T193] __linkwatch_run_queue+0x10b/0x200
[ 375.076244][ T193] linkwatch_event+0x21/0x30
[ 375.077274][ T193] process_one_work+0x252/0x600
[ 375.078379][ T193] ? process_one_work+0x600/0x600
[ 375.079518][ T193] worker_thread+0x3c/0x380
[ 375.080534][ T193] ? process_one_work+0x600/0x600
[ 375.081668][ T193] kthread+0x139/0x150
[ 375.082567][ T193] ? kthread_park+0x90/0x90
[ 375.083567][ T193] ret_from_fork+0x22/0x30
Fixes: e826eafa65c6 ("bonding: Call netif_carrier_off after register_netdevice")
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit below caused a regression for clearfog-gt-8k, where the link
between the switch and the host does not come up.
Investigation revealed two issues:
- MV88E6xxx DSA no longer allows an in-band link to come up as the link
is programmed to be forced down. Commit "net: dsa: mv88e6xxx: fix
in-band AN link establishment" addresses this.
- The dts configured dissimilar link modes at each end of the host to
switch link; the host was configured using a fixed link (so has no
in-band status) and the switch was configured to expect in-band
status.
With both issues fixed, the regression is resolved.
Fixes: 34b5e6a33c1a ("net: dsa: mv88e6xxx: Configure MAC when using fixed link")
Reported-by: Martin Rowe <martin.p.rowe@gmail.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If in-band negotiation or fixed-link modes are specified for a DSA
port, the DSA code will force the link down during initialisation. For
fixed-link mode, this is fine, as phylink will manage the link state.
However, for in-band mode, phylink expects the PCS to detect link,
which will not happen if the link is forced down.
There is a related issue that in in-band mode, the link could come up
while we are making configuration changes, so we should force the link
down prior to reconfiguring the interface mode.
This patch addresses both issues.
Fixes: 3be98b2d5fbc ("net: dsa: Down cpu/dsa ports phylink will control")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PP bcast is marked as doing async reset after job is done.
When resume after suspend, each PP is reset individually,
so no need to reset in PP bcast resume. But I forgot to
clear the PP bcast async reset mark so call into async wait
before job run and gets timeout.
Closes: https://gitlab.freedesktop.org/lima/linux/-/issues/34
Fixes: 3446d7e9883d ("drm/lima: add resume/suspend callback for each ip")
Reviewed-by: Erico Nunes <nunes.erico@gmail.com>
Signed-off-by: Qiang Yu <yuq825@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200719073050.776962-1-yuq825@gmail.com
|
|
This fixes a regression encountered while running the
gdb.base/corefile.exp test in GDB's test suite.
In my testing, the typo prevented the sw_reserved field of struct
fxregs_state from being output to the kernel XSAVES area. Thus the
correct mask corresponding to XCR0 was not present in the core file for
GDB to interrogate, resulting in the following behavior:
[kev@f32-1 gdb]$ ./gdb -q testsuite/outputs/gdb.base/corefile/corefile testsuite/outputs/gdb.base/corefile/corefile.core
Reading symbols from testsuite/outputs/gdb.base/corefile/corefile...
[New LWP 232880]
warning: Unexpected size of section `.reg-xstate/232880' in core file.
With the typo fixed, the test works again as expected.
Signed-off-by: Kevin Buettner <kevinb@redhat.com>
Fixes: 9e4636545933 ("copy_xstate_to_kernel(): don't leave parts of destination uninitialized")
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Dave Airlie <airlied@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
|
|
Karsten Graul says:
====================
net/smc: fixes 2020-07-16
Please apply the following patch series for smc to netdev's net tree.
The patches address problems caused by late or unexpected link layer
control packets, dma sync calls for unmapped memory, freed buffers
that are not removed from the buffer list and a possible null pointer
access that results in a crash.
v1->v2: in patch 4, improve patch description and correct the comment
for the new mutex
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a listen socket is closed then all non-accepted sockets in its
accept queue are to be released. Inside __smc_release() the helper
smc_restore_fallback_changes() restores the changes done to the socket
without to check if the clcsocket has a file set. This can result in
a crash. Fix this by checking the file pointer first.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: f536dffc0b79 ("net/smc: fix closing of fallback SMC sockets")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Two buffers are allocated for each SMC connection. Each buffer is
added to a buffer list after creation. When the second buffer
allocation fails, the first buffer is freed but not deleted from
the list. This might result in crashes when another connection picks
up the freed buffer later and starts to work with it.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 6511aad3f039 ("net/smc: change smc_buf_free function parameters")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The dma related ...sync_sg... functions check the link state before the
dma function is actually called. But the check in smc_link_usable()
allows links in ACTIVATING state which are not yet mapped to dma memory.
Under high load it may happen that the sync_sg functions are called for
such a link which results in an debug output like
DMA-API: mlx5_core 0002:00:00.0: device driver tries to sync
DMA memory it has not allocated [device address=0x0000000103370000]
[size=65536 bytes]
To fix that introduce a helper to check for the link state ACTIVE and
use it where appropriate. And move the link state update to ACTIVATING
to the end of smcr_link_init() when most initial setup is done.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: d854fcbfaeda ("net/smc: add new link state and related helpers")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As smc client the delete link requests are assigned to the flow when
_any_ flow is active. This may break other flows that do not expect
delete link requests during their handling. Fix that by assigning the
request only when an add link flow is active. With that fix the code
for smc client and smc server is the same, so remove the separate
handling.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 9ec6bf19ec8b ("net/smc: llc_del_link_work and use the LLC flow for delete link")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a new ib device is up smc will send an add link invitation to the
peer if needed. This is currently done with rudimentary flow control.
Under high workload these add link invitations can disturb other llc
flows because they arrive unexpected. Fix this by integrating the
invitations into the normal llc event flow and handle them as a flow.
While at it, check for already assigned requests in the flow before
the new add link request is assigned.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: 1f90a05d9ff9 ("net/smc: add smcr_port_add() and smcr_link_up() processing")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To be save from unexpected or late llc response messages check if the
arrived message fits to the current flow type and drop out-of-flow
messages. And drop it when there is already a response assigned to
the flow.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: ef79d439cd12 ("net/smc: process llc responses in tasklet context")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before an smc ib device is used the first time for an smc link it is
lazily initialized. When there are 2 active link groups and a new ib
device is brought online then it might happen that 2 link creations run
in parallel and enter smc_ib_setup_per_ibdev(). Both allocate new send
and receive completion queues on the device, but only one set of them
keeps assigned and the other leaks.
Fix that by protecting the setup and cleanup code using a mutex.
Reviewed-by: Ursula Braun <ubraun@linux.ibm.com>
Fixes: f3c1deddb21c ("net/smc: separate function for link initialization")
Signed-off-by: Karsten Graul <kgraul@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
