| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/soc
DaVinci SoC updates for v5.9
This pull requests contains some clean-ups for SoC support.
No functional changes included.
* tag 'davinci-for-v5.9/soc' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: dm646x-evm: Simplify error handling in 'evm_sw_setup()'
ARM: davinci: Fix trivial spelling
ARM: davinci: Replace HTTP links with HTTPS ones
Link: https://lore.kernel.org/r/348578af-71ea-812e-ec42-31afe7847b85@ti.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/dt
mvebu dt64 for 5.9 (part 1)
Add SMMU support for the Marvell AP806 based SoCs (Armada 70xx and
Armada 80xx)
* tag 'mvebu-dt64-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
arm64: dts: marvell: add SMMU support
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu into arm/dt
mvebu dt for 5.9 (part 1)
- Fix the reg-init PHY for the dlink-dns327l (Armada 370)
- Replace HTTP links with HTTPS one in device tree of the Excito
Bubba B3 (Kirkwood)
* tag 'mvebu-dt-5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/gclement/mvebu:
ARM: dts: dlink-dns327l: fix reg-init PHY
ARM: dts: kirkwood: Replace HTTP links with HTTPS ones
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux into arm/dt
Texas Instruments K3 SoC DT updates for v5.9
- Add platforms chipid nodes for am65x and j721e
- Update latest data sheet values for MMC on am65x
- Add serdes and usb3 support for j721e
- Add analog audio support for j721e
- Add SD card support for am65x
- Rename DT nodes for gic-its/smmu to their standard counterparts am65x/j721e
- HTTP links replaced with HTTPS ones
* tag 'ti-k3-dt-for-v5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/kristo/linux:
arm64: dts: k3-j721e-proc-board: Add wait time for sampling Type-C DIR line
arm64: dts: ti: k3-j721e: Enable Super-Speed support for USB0
arm64: dts: ti: k3-j721e-main.dtsi: Add USB to SERDES MUX
arm64: dts: ti: k3-j721e-main: Add system controller node and SERDES lane mux
arm64: dts: ti: k3-j721e-main: Add WIZ and SERDES PHY nodes
dt-bindings: mfd: ti,j721e-system-controller.yaml: Add J721e system controller
arm64: dts: ti: k3-am65/j721e-main: rename gic-its node to msi-controller
arm64: dts: ti: k3-j721e-main: rename smmu node to iommu
arm64: dts: ti: k3-*: Replace HTTP links with HTTPS ones
arm64: dts: ti: k3-am654-base-board: Add support for SD card
arm64: dts: ti: k3-am65-main: Add support for sdhci1
arm64: dts: ti: j721e-common-proc-board: Analog audio support
arm64: dts: ti: k3-j721e-common-proc-board: Remove duplicated main_i2c1_exp4_pins_default
arm64: dts: ti: k3-am654-main: Update otap-del-sel values
arm64: dts: ti: k3-j721e-mcu-wakeup: add k3 platforms chipid module node
arm64: dts: ti: k3-am65-wakeup: add k3 platforms chipid module node
Link: https://lore.kernel.org/r/3b3b9214-769d-ba1b-db5e-44414a8c5756@ti.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch adds the initial support for the Amazon's Annapurna Labs
Alpine v3 Soc and Evaluation Platform (EVP).
Link: https://lore.kernel.org/r/20200724132654.16549-7-hhhawa@amazon.com
Signed-off-by: Ronen Krupnik <ronenk@amazon.com>
Signed-off-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: Hanna Hawa <hhhawa@amazon.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
This patch adds DT bindings info for Amazon Annapurna Labs Alpine V3.
Link: https://lore.kernel.org/r/20200724132654.16549-6-hhhawa@amazon.com
Signed-off-by: Hanna Hawa <hhhawa@amazon.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Amazon Annapurna Labs Alpine family includes: Alpine-v1, Alpine-v2.
This patch adds the missing DT binding of Alpine-v2 in amazon,al.yaml.
Link: https://lore.kernel.org/r/20200724132654.16549-5-hhhawa@amazon.com
Signed-off-by: Hanna Hawa <hhhawa@amazon.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Update maintainers of amazon,al DT bindings.
Link: https://lore.kernel.org/r/20200724132654.16549-4-hhhawa@amazon.com
Signed-off-by: Hanna Hawa <hhhawa@amazon.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
As preparation to add device tree binding for Amazon's Annapurna Labs
Alpine v3 support. Rename al device tree folder to be amazon.
Link: https://lore.kernel.org/r/20200724132654.16549-3-hhhawa@amazon.com
Signed-off-by: Hanna Hawa <hhhawa@amazon.com>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
As preparation to add device tree binding for Amazon's Annapurna Labs
Alpine v3 support. Rename al,alpine DT binding to amazon,al.
Link: https://lore.kernel.org/r/20200724132654.16549-2-hhhawa@amazon.com
Signed-off-by: Hanna Hawa <hhhawa@amazon.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
GDB regression
If a tracee is uprobed and it hits int3 inserted by debugger, handle_swbp()
does send_sig(SIGTRAP, current, 0) which means si_code == SI_USER. This used
to work when this code was written, but then GDB started to validate si_code
and now it simply can't use breakpoints if the tracee has an active uprobe:
# cat test.c
void unused_func(void)
{
}
int main(void)
{
return 0;
}
# gcc -g test.c -o test
# perf probe -x ./test -a unused_func
# perf record -e probe_test:unused_func gdb ./test -ex run
GNU gdb (GDB) 10.0.50.20200714-git
...
Program received signal SIGTRAP, Trace/breakpoint trap.
0x00007ffff7ddf909 in dl_main () from /lib64/ld-linux-x86-64.so.2
(gdb)
The tracee hits the internal breakpoint inserted by GDB to monitor shared
library events but GDB misinterprets this SIGTRAP and reports a signal.
Change handle_swbp() to use force_sig(SIGTRAP), this matches do_int3_user()
and fixes the problem.
This is the minimal fix for -stable, arch/x86/kernel/uprobes.c is equally
wrong; it should use send_sigtrap(TRAP_TRACE) instead of send_sig(SIGTRAP),
but this doesn't confuse GDB and needs another x86-specific patch.
Reported-by: Aaron Merey <amerey@redhat.com>
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reviewed-by: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200723154420.GA32043@redhat.com
|
|
Initially CONFIG_CRYPTO_AES_586=y was added to the i386_defconfig file in:
c1b362e3b4d3: ("x86: update defconfigs")
The code and Kconfig for CONFIG_CRYPTO_AES_586 was removed in:
1d2c3279311e: ("crypto: x86/aes - drop scalar assembler implementations")
Remove the leftover from the i386_defconfig file as well.
Signed-off-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20200723171119.9881-1-sedat.dilek@gmail.com
|
|
Since the default_wake_function() passes its flags onto
try_to_wake_up(), warn if those flags collide with internal values.
Given that the supplied flags are garbage, no repair can be done but at
least alert the user to the damage they are causing.
In the belief that these errors should be picked up during testing, the
warning is only compiled in under CONFIG_SCHED_DEBUG.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: https://lore.kernel.org/r/20200723201042.18861-1-chris@chris-wilson.co.uk
|
|
Allocate the time namespace page among VVAR pages. Provide
__arch_get_timens_vdso_data() helper for VDSO code to get the
code-relative position of VVARs on that special page.
If a task belongs to a time namespace then the VVAR page which contains
the system wide VDSO data is replaced with a namespace specific page
which has the same layout as the VVAR page. That page has vdso_data->seq
set to 1 to enforce the slow path and vdso_data->clock_mode set to
VCLOCK_TIMENS to enforce the time namespace handling path.
The extra check in the case that vdso_data->seq is odd, e.g. a concurrent
update of the VDSO data is in progress, is not really affecting regular
tasks which are not part of a time namespace as the task is spin waiting
for the update to finish and vdso_data->seq to become even again.
If a time namespace task hits that code path, it invokes the corresponding
time getter function which retrieves the real VVAR page, reads host time
and then adds the offset for the requested clock which is stored in the
special VVAR page.
The time-namespace page isn't allocated on !CONFIG_TIME_NAMESPACE, but
vma is the same size, which simplifies criu/vdso migration between
different kernel configs.
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Dmitry Safonov <dima@arista.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20200624083321.144975-4-avagin@gmail.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
The order of vvar pages depends on whether a task belongs to the root
time namespace or not. In the root time namespace, a task doesn't have a
per-namespace page. In a non-root namespace, the VVAR page which contains
the system-wide VDSO data is replaced with a namespace specific page
that contains clock offsets.
Whenever a task changes its namespace, the VVAR page tables are cleared
and then they will be re-faulted with a corresponding layout.
A task can switch its time namespace only if its ->mm isn't shared with
another task.
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Dmitry Safonov <dima@arista.com>
Reviewed-by: Christian Brauner <christian.brauner@ubuntu.com>
Link: https://lore.kernel.org/r/20200624083321.144975-3-avagin@gmail.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Currently the vdso has no awareness of time namespaces, which may
apply distinct offsets to processes in different namespaces. To handle
this within the vdso, we'll need to expose a per-namespace data page.
As a preparatory step, this patch separates the vdso data page from
the code pages, and has it faulted in via its own fault callback.
Subsquent patches will extend this to support distinct pages per time
namespace.
The vvar vma has to be installed with the VM_PFNMAP flag to handle
faults via its vma fault callback.
Signed-off-by: Andrei Vagin <avagin@gmail.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20200624083321.144975-2-avagin@gmail.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
<linux/instrumentation.h> header
Linus pointed out that compiler.h - which is a key header that gets included in every
single one of the 28,000+ kernel files during a kernel build - was bloated in:
655389666643: ("vmlinux.lds.h: Create section for protection against instrumentation")
Linus noted:
> I have pulled this, but do we really want to add this to a header file
> that is _so_ core that it gets included for basically every single
> file built?
>
> I don't even see those instrumentation_begin/end() things used
> anywhere right now.
>
> It seems excessive. That 53 lines is maybe not a lot, but it pushed
> that header file to over 12kB, and while it's mostly comments, it's
> extra IO and parsing basically for _every_ single file compiled in the
> kernel.
>
> For what appears to be absolutely zero upside right now, and I really
> don't see why this should be in such a core header file!
Move these primitives into a new header: <linux/instrumentation.h>, and include that
header in the headers that make use of it.
Unfortunately one of these headers is asm-generic/bug.h, which does get included
in a lot of places, similarly to compiler.h. So the de-bloating effect isn't as
good as we'd like it to be - but at least the interfaces are defined separately.
No change to functionality intended.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20200604071921.GA1361070@gmail.com
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Peter Zijlstra <peterz@infradead.org>
|
|
Currently, if a section has a relocation to '_mcount' symbol, a new
__mcount_loc entry will be added whatever the relocation type is.
This is problematic when a relocation to '_mcount' is in the middle of a
section and is not a call for ftrace use.
Such relocation could be generated with below code for example:
bool is_mcount(unsigned long addr)
{
return (target == (unsigned long) &_mcount);
}
With this snippet of code, ftrace will try to patch the mcount location
generated by this code on module load and fail with:
Call trace:
ftrace_bug+0xa0/0x28c
ftrace_process_locs+0x2f4/0x430
ftrace_module_init+0x30/0x38
load_module+0x14f0/0x1e78
__do_sys_finit_module+0x100/0x11c
__arm64_sys_finit_module+0x28/0x34
el0_svc_common+0x88/0x194
el0_svc_handler+0x38/0x8c
el0_svc+0x8/0xc
---[ end trace d828d06b36ad9d59 ]---
ftrace failed to modify
[<ffffa2dbf3a3a41c>] 0xffffa2dbf3a3a41c
actual: 66:a9:3c:90
Initializing ftrace call sites
ftrace record flags: 2000000
(0)
expected tramp: ffffa2dc6cf66724
So Limit the relocation type to R_AARCH64_CALL26 as in perl version of
recordmcount.
Fixes: af64d2aa872a ("ftrace: Add arm64 support to recordmcount")
Signed-off-by: Gregory Herrero <gregory.herrero@oracle.com>
Acked-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Link: https://lore.kernel.org/r/20200717143338.19302-1-gregory.herrero@oracle.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
While MTE is not supported in the upstream kernel yet, add a comment
that HWCAP2_MTE as (1 << 18) is reserved. Glibc makes use of it for the
resolving (ifunc) of the MTE-safe string routines.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Sealevel XR17V35X based devices are inoperable on kernel versions
4.11 and above due to a change in the GPIO preconfiguration introduced in
commit
7dea8165f1d. This patch fixes this by preconfiguring the GPIO on Sealevel
cards to the value (0x00) used prior to commit 7dea8165f1d
With GPIOs preconfigured as per commit 7dea8165f1d all ports on
Sealevel XR17V35X based devices become stuck in high impedance
mode, regardless of dip-switch or software configuration. This
causes the device to become effectively unusable. This patch (in
various forms) has been distributed to our customers and no issues
related to it have been reported.
Fixes: 7dea8165f1d6 ("serial: exar: Preconfigure xr17v35x MPIOs as output")
Signed-off-by: Matthew Howell <matthew.howell@sealevel.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2007221605270.13247@tstest-VirtualBox
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is tripping up the format modifier patches.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Stale pointer was tripping up the unload path.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Fixes a race on Turing between the core cross-channel error checks and
the following window update.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
The disp015x classes are used by both gt21x and gf1xx (aside from gf119), but page
kinds differ between Tesla and Fermi.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
Fixes: 9b5ca547bb8 ("drm/nouveau/disp/gm200-: detect and potentially disable HDA support on some SORs")
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
|
|
To support the change in "phy: armada-38x: fix NETA lockup when
repeatedly switching speeds" we need to update the DT with the
additional register.
Fixes: 14dc100b4411 ("phy: armada38x: add common phy support")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The macro is not used anywhere, and has an incorrect value (going by the
comment) on x86_64 since commit c898faf91b3e ("x86: 46 bit physical address
support on 64 bits")
To avoid confusion, just remove the definition.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20200723231544.17274-2-nivedita@alum.mit.edu
|
|
Check for regmap_read() return code before using the read value in
following write in exynos5_switch_timing_regs(). Pass reading error
code to the callers.
This does not introduce proper error handling for such failed reads (and
obviously regmap_write() error is still ignored) because the driver
ignored this in all places. Therefor it only fixes reported issue while
matching current driver coding style:
drivers/memory/samsung/exynos5422-dmc.c: In function 'exynos5_switch_timing_regs':
>> drivers/memory/samsung/exynos5422-dmc.c:216:6: warning: variable 'ret' set but not used [-Wunused-but-set-variable]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
In case a TPM2 is attached, search for a TPM2 ACPI table when trying
to get the event log from ACPI. If one is found, use it to get the
start and length of the log area. This allows non-UEFI systems, such
as SeaBIOS, to pass an event log when using a TPM2.
Cc: Peter Huewe <peterhuewe@gmx.de>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Recent extensions of the TPM2 ACPI table added 3 more fields
including 12 bytes of start method specific parameters and Log Area
Minimum Length (u32) and Log Area Start Address (u64). So, we define
a new structure acpi_tpm2_phy that holds these optional new fields.
The new fields allow non-UEFI systems to access the TPM2's log.
The specification that has the new fields is the following:
TCG ACPI Specification
Family "1.2" and "2.0"
Version 1.2, Revision 8
https://trustedcomputinggroup.org/wp-content/uploads/TCG_ACPIGeneralSpecification_v1.20_r8.pdf
Cc: linux-acpi@vger.kernel.org
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Stefan Berger <stefanb@linux.ibm.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
The size of the buffers for storing context's and sessions can vary from
arch to arch as PAGE_SIZE can be anything between 4 kB and 256 kB (the
maximum for PPC64). Define a fixed buffer size set to 16 kB. This should be
enough for most use with three handles (that is how many we allow at the
moment). Parametrize the buffer size while doing this, so that it is easier
to revisit this later on if required.
Cc: stable@vger.kernel.org
Reported-by: Stefan Berger <stefanb@linux.ibm.com>
Fixes: 745b361e989a ("tpm: infrastructure for TPM spaces")
Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com>
Tested-by: Stefan Berger <stefanb@linux.ibm.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Enable pwm_tacho device for fan control and monitoring in Wedge40.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Enable ADC controller and corresponding voltage sensoring channels for
Wedge40.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Disable i2c bus #9, #10 and #13 as these i2c controllers are not used on
Wedge40.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Create all the i2c switches in device tree and use aliases to assign
child channels with consistent bus numbers.
Besides, "i2c-mux-idle-disconnect" is set for all the i2c switches to
avoid potential conflicts when multiple devices (beind the switches)
use the same device address.
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The GPIO on Q0 is used for resetting the CFAM of the processor that the
ASPEED master is connected to.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
The GPIO on Q0 is used for resetting the CFAM of the processor that the
ASPEED master is connected to.
The signal is wired as active high on the first pass systems.
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Require that the TCG_PCR_EVENT2.digests.count value strictly matches the
value of TCG_EfiSpecIdEvent.numberOfAlgorithms in the event field of the
TCG_PCClientPCREvent event log header. Also require that
TCG_EfiSpecIdEvent.numberOfAlgorithms is non-zero.
The TCG PC Client Platform Firmware Profile Specification section 9.1
(Family "2.0", Level 00 Revision 1.04) states:
For each Hash algorithm enumerated in the TCG_PCClientPCREvent entry,
there SHALL be a corresponding digest in all TCG_PCR_EVENT2 structures.
Note: This includes EV_NO_ACTION events which do not extend the PCR.
Section 9.4.5.1 provides this description of
TCG_EfiSpecIdEvent.numberOfAlgorithms:
The number of Hash algorithms in the digestSizes field. This field MUST
be set to a value of 0x01 or greater.
Enforce these restrictions, as required by the above specification, in
order to better identify and ignore invalid sequences of bytes at the
end of an otherwise valid TPM2 event log. Firmware doesn't always have
the means necessary to inform the kernel of the actual event log size so
the kernel's event log parsing code should be stringent when parsing the
event log for resiliency against firmware bugs. This is true, for
example, when firmware passes the event log to the kernel via a reserved
memory region described in device tree.
POWER and some ARM systems use the "linux,sml-base" and "linux,sml-size"
device tree properties to describe the memory region used to pass the
event log from firmware to the kernel. Unfortunately, the
"linux,sml-size" property describes the size of the entire reserved
memory region rather than the size of the event long within the memory
region and the event log format does not include information describing
the size of the event log.
tpm_read_log_of(), in drivers/char/tpm/eventlog/of.c, is where the
"linux,sml-size" property is used. At the end of that function,
log->bios_event_log_end is pointing at the end of the reserved memory
region. That's typically 0x10000 bytes offset from "linux,sml-base",
depending on what's defined in the device tree source.
The firmware event log only fills a portion of those 0x10000 bytes and
the rest of the memory region should be zeroed out by firmware. Even in
the case of a properly zeroed bytes in the remainder of the memory
region, the only thing allowing the kernel's event log parser to detect
the end of the event log is the following conditional in
__calc_tpm2_event_size():
if (event_type == 0 && event_field->event_size == 0)
size = 0;
If that wasn't there, __calc_tpm2_event_size() would think that a 16
byte sequence of zeroes, following an otherwise valid event log, was
a valid event.
However, problems can occur if a single bit is set in the offset
corresponding to either the TCG_PCR_EVENT2.eventType or
TCG_PCR_EVENT2.eventSize fields, after the last valid event log entry.
This could confuse the parser into thinking that an additional entry is
present in the event log and exposing this invalid entry to userspace in
the /sys/kernel/security/tpm0/binary_bios_measurements file. Such
problems have been seen if firmware does not fully zero the memory
region upon a warm reboot.
This patch significantly raises the bar on how difficult it is for
stale/invalid memory to confuse the kernel's event log parser but
there's still, ultimately, a reliance on firmware to properly initialize
the remainder of the memory region reserved for the event log as the
parser cannot be expected to detect a stale but otherwise properly
formatted firmware event log entry.
Fixes: fd5c78694f3f ("tpm: fix handling of the TPM 2.0 event logs")
Signed-off-by: Tyler Hicks <tyhicks@linux.microsoft.com>
Reviewed-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
|
|
Pablo Neira Ayuso says:
====================
Netfilter/IPVS fixes for net
The following patchset contains Netfilter/IPVS fixes for net:
1) Fix NAT hook deletion when table is dormant, from Florian Westphal.
2) Fix IPVS sync stalls, from guodeqing.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
geneve_nl2info() sets 'df' conditionally, so we have to
initialize it by copying the value from existing geneve
device in geneve_changelink().
Fixes: 56c09de347e4 ("geneve: allow changing DF behavior after creation")
Reported-by: syzbot+7ebc2e088af5e4c0c9fa@syzkaller.appspotmail.com
Cc: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Sabrina Dubroca <sd@queasysnail.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Very similar to commit 544f287b8495
("bonding: check error value of register_netdevice() immediately"),
we should immediately check the return value of register_netdevice()
before doing anything else.
Fixes: 005db31d5f5f ("bonding: set carrier off for devices created through netlink")
Reported-and-tested-by: syzbot+bbc3a11c4da63c1b74d6@syzkaller.appspotmail.com
Cc: Beniamino Galvani <bgalvani@redhat.com>
Cc: Taehee Yoo <ap420073@gmail.com>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 9ffad9263b467efd8f8dc7ae1941a0a655a2bab2.
Upon additional testing with older servers, it was found that
the original commit introduced a regression when using the old SMB1
dialect and rsyncing over an existing file.
The patch will need to be respun to address this, likely including
a larger refactoring of the SMB1 and SMB3 rename code paths to make
it less confusing and also to address some additional rename error
cases that SMB3 may be able to workaround.
Signed-off-by: Steve French <stfrench@microsoft.com>
Reported-by: Patrick Fernie <patrick.fernie@gmail.com>
CC: Stable <stable@vger.kernel.org>
Acked-by: Ronnie Sahlberg <lsahlber@redhat.com>
Acked-by: Pavel Shilovsky <pshilov@microsoft.com>
Acked-by: Zhang Xiaoxu <zhangxiaoxu5@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux into master
Pull s390 fixes from Heiko Carstens:
- Change cpum_cf/perf counter name from DFLT_CCERROR to DFLT_CCFINISH
to reflect reality and avoid further confusion. This is a user space
visible change therefore the commit has also a stable tag for 5.7,
where this counter was introduced.
- Add Matthew Rosato as s390 IOMMU maintainer.
* tag 's390-5.8-6' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
MAINTAINERS: add Matthew for s390 IOMMU
s390/cpum_cf,perf: change DFLT_CCERROR counter name
|
|
When I have KASAN enabled on my kernel and I start stressing the
touchscreen my system tends to hang. The touchscreen is one of the
only things that does a lot of big i2c transfers and ends up hitting
the DMA paths in the geni i2c driver. It appears that KASAN adds
enough delay in my system to tickle a race condition in the DMA setup
code.
When the system hangs, I found that it was running the geni_i2c_irq()
over and over again. It had these:
m_stat = 0x04000080
rx_st = 0x30000011
dm_tx_st = 0x00000000
dm_rx_st = 0x00000000
dma = 0x00000001
Notably we're in DMA mode but are getting M_RX_IRQ_EN and
M_RX_FIFO_WATERMARK_EN over and over again.
Putting some traces in geni_i2c_rx_one_msg() showed that when we
failed we were getting to the start of geni_i2c_rx_one_msg() but were
never executing geni_se_rx_dma_prep().
I believe that the problem here is that we are starting the geni
command before we run geni_se_rx_dma_prep(). If a transfer makes it
far enough before we do that then we get into the state I have
observed. Let's change the order, which seems to work fine.
Although problems were seen on the RX path, code inspection suggests
that the TX should be changed too. Change it as well.
Fixes: 37692de5d523 ("i2c: i2c-qcom-geni: Add bus driver for the Qualcomm GENI I2C controller")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
On R-Car Gen2, we get a timeout when reading from the address set in
ICSAR, even though the slave interface is disabled. Clearing it fixes
this situation. Note that Gen3 is not affected.
To reproduce: bind and undbind an I2C slave on some bus, run
'i2cdetect' on that bus.
Fixes: de20d1857dd6 ("i2c: rcar: add slave support")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
|
|
Previously TLP may send multiple probes of new data in one
flight. This happens when the sender is cwnd limited. After the
initial TLP containing new data is sent, the sender receives another
ACK that acks partial inflight. It may re-arm another TLP timer
to send more, if no further ACK returns before the next TLP timeout
(PTO) expires. The sender may send in theory a large amount of TLP
until send queue is depleted. This only happens if the sender sees
such irregular uncommon ACK pattern. But it is generally undesirable
behavior during congestion especially.
The original TLP design restrict only one TLP probe per inflight as
published in "Reducing Web Latency: the Virtue of Gentle Aggression",
SIGCOMM 2013. This patch changes TLP to send at most one probe
per inflight.
Note that if the sender is app-limited, TLP retransmits old data
and did not have this issue.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We recently added some bounds checking in ax25_connect() and
ax25_sendmsg() and we so we removed the AX25_MAX_DIGIS checks because
they were no longer required.
Unfortunately, I believe they are required to prevent integer overflows
so I have added them back.
Fixes: 8885bb0621f0 ("AX.25: Prevent out-of-bounds read in ax25_sendmsg()")
Fixes: 2f2a7ffad5c6 ("AX.25: Fix out-of-bounds read in ax25_connect()")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit adc0daad366b62ca1bce3e2958a40b0b71a8b8b3 ("dm: report suspended
device during destroy") broke integrity recalculation.
The problem is dm_suspended() returns true not only during suspend,
but also during resume. So this race condition could occur:
1. dm_integrity_resume calls queue_work(ic->recalc_wq, &ic->recalc_work)
2. integrity_recalc (&ic->recalc_work) preempts the current thread
3. integrity_recalc calls if (unlikely(dm_suspended(ic->ti))) goto unlock_ret;
4. integrity_recalc exits and no recalculating is done.
To fix this race condition, add a function dm_post_suspending that is
only true during the postsuspend phase and use it instead of
dm_suspended().
Signed-off-by: Mikulas Patocka <mpatocka redhat com>
Fixes: adc0daad366b ("dm: report suspended device during destroy")
Cc: stable vger kernel org # v4.18+
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
IOSQE_ASYNC branch of io_queue_sqe() is another place where an
unitialised req->work can be accessed (i.e. prior io_req_init_async()).
Nothing really bad though, it just looses IO_WQ_WORK_CONCURRENT flag.
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When we have no primary fwnode or when it's a software node, we may end up
in the situation when fwnode is a NULL pointer. There is no point to look for
secondary fwnode in such case. Add a necessary check to a condition.
Fixes: 114dbb4fa7c4 ("drivers property: When no children in primary, try secondary")
Reported-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Maxim Levitsky <mlevitsk@redhat.com>
Link: https://lore.kernel.org/r/20200716182747.54929-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
