| Age | Commit message (Collapse) | Author |
|---|
|
lan78xx.c:2282 tx_complete() warn: variable dereferenced before check 'skb' (see line 2249)
lan78xx.c:2885 lan78xx_bh() info: ignoring unreachable code.
lan78xx.c:3159 lan78xx_probe() info: ignoring unreachable code.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the first slave is added (such as during bootup) the first
gratuitous ARP gets dropped. We don't see this drop during a failover.
The packet gets dropped in qdisc (noop_enqueue).
The fix is to delay the sending of gratuitous ARPs till the bond dev's
carrier is present.
It can also be worked around by setting num_grat_arp to more than 1.
Signed-off-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
altera_tse_private->sgdmadesclen is always assigned assigned the same
value and never changes during runtime. Remove the struct member and
use a new define for sizeof(struct sgdma_descrip) instead.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case we need to divert reads/writes using the slave MII bus, we may have
already fetched a valid PHY interface property from Device Tree, and that
mode is used by the PHY driver to make configuration decisions.
If we could not fetch the "phy-mode" property, we will assign p->phy_interface
to PHY_INTERFACE_MODE_NA, such that we can actually check for that condition as
to whether or not we should override the interface value.
Fixes: 19334920eaf7 ("net: dsa: Set valid phy interface type")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before the make_empty_dir_inode calls were introduce into proc, sysfs,
and sysctl those directories when stated reported an i_size of 0.
make_empty_dir_inode started reporting an i_size of 2. At least one
userspace application depended on stat returning i_size of 0. So
modify make_empty_dir_inode to cause an i_size of 0 to be reported for
these directories.
Cc: stable@vger.kernel.org
Reported-by: Tejun Heo <tj@kernel.org>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
When the snapshot overflows because of a write to the origin, the on-disk
image has to be invalidated. However, when the snapshot overflows because
of a write to the snapshot, the on-disk image doesn't have to be
invalidated. Change the behavior so that the on-disk image is not
invalidated in this case.
When the snapshot overflows, the variable snapshot_overflowed is set.
All writes to the snapshot are disallowed to minimize filesystem
corruption - this condition is cleared when the snapshot is deactivated
and activated.
The user can extend the overflowed snapshot, deactivate and activate it
again, run fsck (if journaling filesystem is not used) mount it and
recover the data.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Support HighPoint RR36xx HBAs which are based on Marvell Frey.
Support SAS tape and SAS media changer.
[jejb: remove now unused label]
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
The code that places signals in signal queues computes the uids, gids,
and pids at the time the signals are enqueued. Which means that tasks
that share signal queues must be in the same pid and user namespaces.
Sharing signal handlers is fine, but bizarre.
So make the code in fork and userns_install clearer by only testing
for what is functionally necessary.
Also update the comment in unshare about unsharing a user namespace to
be a little more explicit and make a little more sense.
Acked-by: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
In the logic in the initial commit of unshare made creating a new
thread group for a process, contingent upon creating a new memory
address space for that process. That is wrong. Two separate
processes in different thread groups can share a memory address space
and clone allows creation of such proceses.
This is significant because it was observed that mm_users > 1 does not
mean that a process is multi-threaded, as reading /proc/PID/maps
temporarily increments mm_users, which allows other processes to
(accidentally) interfere with unshare() calls.
Correct the check in check_unshare_flags() to test for
!thread_group_empty() for CLONE_THREAD, CLONE_SIGHAND, and CLONE_VM.
For sighand->count > 1 for CLONE_SIGHAND and CLONE_VM.
For !current_is_single_threaded instead of mm_users > 1 for CLONE_VM.
By using the correct checks in unshare this removes the possibility of
an accidental denial of service attack.
Additionally using the correct checks in unshare ensures that only an
explicit unshare(CLONE_VM) can possibly trigger the slow path of
current_is_single_threaded(). As an explict unshare(CLONE_VM) is
pointless it is not expected there are many applications that make
that call.
Cc: stable@vger.kernel.org
Fixes: b2e0d98705e60e45bbb3c0032c48824ad7ae0704 userns: Implement unshare of the user namespace
Reported-by: Ricky Zhou <rickyz@chromium.org>
Reported-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of new device support, features and cleanup for the 4.3 cycle.
Take 2 also includes a fix set that was too late for the 4.2 cycle.
As we had a lot of tools and docs work in this set, I have broken those
out into their own categories in this description.
Fixes from the pull request '4th set of IIO fixes for the 4.2 cycle'.
* Poll functions for both event chardev and the buffer one were returning
negative error codes (via a positive value).
* A recent change to lsiio adding some error handling that was wrong and
stopped the tool working.
* bmg160 was missing some dependencies in Kconfig
* berlin2-adc had a misshandled register (wrote a value rather than a bitmap)
New device support
* TI opt3001 light sensor
* TXC PA12 ALS and proximity sensor.
* mcp3301 ADC support (in mcp320x driver)
* ST lsm303agr accelerometer and magnetometer drivers (plus some st-sensors
common support to allow different WHOAMI register addresses, devices with
fixed scale and allow interrupt equiped magnetometers).
* ADIS16305, ADIS16367, ADIS16445IMUs (in the adis16400 driver)
* ADIS16266 gyro (in the adis16260 driver)
* ADIS16137 gyro (in the adis16136 driver)
New functionality
* mmc35240 DT bindings.
* Inverse unit conversion macros to aid handing of values written to sysfs
attributes.
Core cleanup
* Forward declaration of struct iio_trigger to avoid a compile warning.
Driver cleanup / fixes
* mxs-lradc
- Clarify which parts are supported.
- Fix spelling erorrs.
- Missing/extra includes
- reorder includes
- add datasheet name listings for all usable channels (to allow them
to be bound by name from consumer drivers)
* acpi-als - add some function prefixes as per general iio style.
* bmc150_magn - replace a magic value with the existing define.
* vf610 - determine possible sample frequencies taking into account the
electrical characteristics (defining a minimum sample time)
* dht11
- whitespace
- additional docs
- avoid mulitple assignments in one line
- Use the new funciton ktime_get_resolution_ns to cleanup a nasty trick
previously used for timing.
* Fix all drivers that consider 0 a valid IRQ for historical reasons.
* Export I2C module alias info where previously missing (to allow autoprobing)
* Export OF module alias info where previously missing.
* mmc35240 - switch some variables into arrays to improve readability.
* mlx90614 - define some magic numbers for readability.
* bmc150_magn
- expand area locked by a mutex to cover all the use of the
data->buffer.
- use descriptive naming for a mask instead of a magic value.
* berin2-adc
- pass up an error code rather that a generic error
- constify the iio_chan_spec
- some other little tidy ups.
* stk8312
- fix a dependency on triggered buffers in kconfig
- add a check for invalid attribute values
- improve error handling by returning error codes where possible and
return immediately where relevant
- rework macro defs to use GENMASK etc
- change some variable types to reduce unnecessary casting
- clean up code style
- drop a local buffer copy for bulk reads and use the one in data->buffer
instead.
* adis16400 - the adis16448 gyroscope scale was wrong.
* adis16480 - some more wrong scales for various parts.
* adis16300 - has an undocumented product id and serial number registers so
use them.
* iio_simple_dummy - fix some wrong code indentation.
* bmc150-accel - use the chip ID to detect the chip present rather than
verifying the expected part was there. This was in response to a wrong
ACPI entry on the WinBook TW100.
* mma8452
- fix _get_hp_filter_index
- drop a double include
- pass up an error code rather than rewriting it
- range check input values to attribute writes
- register defs tidy up using GENMASK and reordering them to be easier to
follow.
- various coding style cleanups
- put the Kconfig entry in the write place (alphabetically).
Tools related
* Tools cleanup - drop an explicity NULL comparison, some unnecessary braces,
use the ARRAY_SIZE macro, send error messages to stderr instead of dropping
them in the middle of normal output.
* Fix tools to allow that scale and offset attributes are optional.
* More tools fixes including allowing true 32bit data (previously an overflow
prevented more than 31bits)
* Drop a stray header guard that ended up in a c file.
* Make calc_digits static as it isn't exported or in the header.
* Set ci_array pointer to NULL after free as a protection against non safe
usage of the tools core code. Also convert a double pointer to a single
one as the extra level of indirection was unnecessary.
Docs
* DocBook introduction by Daniel Baluta. Glad we are beginning to
draw together some more introductory docs to suplement the various
tools / examples.
* Drop bytes_per_datum sysfs attribute docs as it no longer exists.
* A whole load of missing / fixing of kernel-doc for the core of IIO.
* Document the trigger name sysfs attribute in the ABI docs.
* Minor typos in the ABI docs related to power down modes.
|
|
LTC3887 is an enhanced version of LTC3880 and supports the same commands.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Per datasheet, the chip ID for LTM4676 is 0x448x. This was observed
in real systems. In addition to that, chip ID 0x4401 was observed
as well. Research shows that the chip ID has been changed from 0x440x
to 0x448x in datasheet revision C. Add support for the additional chip ID.
Also add the chip ID for LTM4676A, which is functionally identical
to LTM4676.
Reported-by: Ananda Babu Nettam <anandab@juniper.net>
Cc: Ananda Babu Nettam <anandab@juniper.net>
Cc: Amit U Jain <amjain@juniper.net>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
LTC3882 is mostly compatible with LTC3880. Major differences are that it
does not measure the input current, and it no longer supports LTC's legacy
mechanism to identify the chip.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Verifying the chip type is getting more complicated with new chips,
since not all chips support the same mechanism to read the chip type.
Move the code into a separate function to simplify adding support for
those chips.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Commit bcdb247c6b6a ("sd: Limit transfer length") clamped the maximum
size of an I/O request to the MAXIMUM TRANSFER LENGTH field in the BLOCK
LIMITS VPD. This had the unfortunate effect of also limiting the maximum
size of non-filesystem requests sent to the device through sg/bsg.
Avoid using blk_queue_max_hw_sectors() and set the max_sectors queue
limit directly.
Also update the comment in blk_limits_max_hw_sectors() to clarify that
max_hw_sectors defines the limit for the I/O controller only.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reported-by: Brian King <brking@linux.vnet.ibm.com>
Tested-by: Brian King <brking@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org # 3.17+
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
This patch changes the st driver to use attribute groups so
driver sysfs files are created automatically. See the
following for reference:
http://kroah.com/log/blog/2013/06/26/how-to-create-a-sysfs-file-correctly/
Signed-off-by: Shane Seymour <shane.seymour@hp.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Kai Mäkisara <kai.makisara@kolumbus.fi>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Resources allocated within bfad_im_port_index idr are not deallocated
on module unload. The patch adds idr_destroy() in exit function.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Negative return values are not supported by iio_event_poll since
its return type is unsigned int.
Fixes: f18e7a068a0a3 ("iio: Return -ENODEV for file operations if the device has been unregistered")
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Change return value to 0 if no device is bound since
unsigned int cannot support negative error codes.
Fixes: f18e7a068 ("iio: Return -ENODEV for file operations if the
device has been unregistered")
Signed-off-by: Cristina Opriceana <cristina.opriceana@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
commit acf50b3586f8d8a7530b905e111dda41876d38f4
"tools:iio:lsiio: add error handling"
introduced error handling of errors returned from
read_sysfs_string(), but with a simple if (retval),
missing the fact that these functions return a positive
value if the read was successful.
As a result lsiio regresses and does not show any
devices on my filesystem. Fix this by checking for
only negative error codes.
Cc: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Hartmut Knaack <knaack.h@gmx.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Catalin Marinas:
"Fix coarse clock monotonicity (VDSO timestamp off by one jiffy
compared to the syscall one)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: VDSO: fix coarse clock monotonicity regression
|
|
Since fc_fcp_cleanup_cmd() can sleep this function must not
be called while holding a spinlock. This patch avoids that
fc_fcp_cleanup_each_cmd() triggers the following bug:
BUG: scheduling while atomic: sg_reset/1512/0x00000202
1 lock held by sg_reset/1512:
#0: (&(&fsp->scsi_pkt_lock)->rlock){+.-...}, at: [<ffffffffc0225cd5>] fc_fcp_cleanup_each_cmd.isra.21+0xa5/0x150 [libfc]
Preemption disabled at:[<ffffffffc0225cd5>] fc_fcp_cleanup_each_cmd.isra.21+0xa5/0x150 [libfc]
Call Trace:
[<ffffffff816c612c>] dump_stack+0x4f/0x7b
[<ffffffff810828bc>] __schedule_bug+0x6c/0xd0
[<ffffffff816c87aa>] __schedule+0x71a/0xa10
[<ffffffff816c8ad2>] schedule+0x32/0x80
[<ffffffffc0217eac>] fc_seq_set_resp+0xac/0x100 [libfc]
[<ffffffffc0218b11>] fc_exch_done+0x41/0x60 [libfc]
[<ffffffffc0225cff>] fc_fcp_cleanup_each_cmd.isra.21+0xcf/0x150 [libfc]
[<ffffffffc0225f43>] fc_eh_device_reset+0x1c3/0x270 [libfc]
[<ffffffff814a2cc9>] scsi_try_bus_device_reset+0x29/0x60
[<ffffffff814a3908>] scsi_ioctl_reset+0x258/0x2d0
[<ffffffff814a2650>] scsi_ioctl+0x150/0x440
[<ffffffff814b3a9d>] sd_ioctl+0xad/0x120
[<ffffffff8132f266>] blkdev_ioctl+0x1b6/0x810
[<ffffffff811da608>] block_ioctl+0x38/0x40
[<ffffffff811b4e08>] do_vfs_ioctl+0x2f8/0x530
[<ffffffff811b50c1>] SyS_ioctl+0x81/0xa0
[<ffffffff816cf8b2>] system_call_fastpath+0x16/0x7a
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
This patch adds selects for IIO_BUFFER and IIO_TRIGGERED_BUFFER. Without
IIO_BUFFER, the driver does not compile.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Active channel number is stored in BERLIN2_SM_CTRL as value, instead of a
bit map.
The masks for channel interrupts and data ready are a 16 bits wide bit
map each, instead of just 4 bits.
Also correct the data mask for the temperature sensor, which was
Reported-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Acked-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Due to patch "libfc: Do not invoke the response handler after
fc_exch_done()" (commit ID 7030fd62) the lport_recv() call
in fc_exch_recv_req() is passed a dangling pointer. Avoid this
by moving the fc_frame_free() call from fc_invoke_resp() to its
callers. This patch fixes the following crash:
general protection fault: 0000 [#3] PREEMPT SMP
RIP: fc_lport_recv_req+0x72/0x280 [libfc]
Call Trace:
fc_exch_recv+0x642/0xde0 [libfc]
fcoe_percpu_receive_thread+0x46a/0x5ed [fcoe]
kthread+0x10a/0x120
ret_from_fork+0x42/0x70
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
In case pci_resource_start() or pci_resource_len() reutrn 0, mvsas_ioremap
returns without doing an iounmap() of mvi->regs_ex.
Found by the cocinelle tool.
Signed-off-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Commit f3ddac1918fe963bcbf8d407a3a3c0881b47248b ("[SCSI] qla2xxx:
Disable adapter when we encounter a PCI disconnect.") has introduced a
code that disables the board, releasing some resources, when reading
0xffffffff.
In case this happens when there is an EEH, this read will trigger EEH
detection and set PCI channel offline. EEH will be able to recover the
card from this state by doing a reset, so it's a better option than
simply disabling the card.
Since eeh_check_failure will mark the channel as offline before
returning the read value, in case there really was an EEH, we can simply
check for pci_channel_offline, preventing the board_disable code from
running if it's true.
Without this patch, EEH code will try to access those same resources
that board_disable will try to free. This race can cause EEH recovery to
fail.
[ 504.370577] EEH: Notify device driver to resume
[ 504.370580] qla2xxx [0001:07:00.0]-9002:2: The device failed to resume I/O from slot/link_reset.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Acked-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Pull amd drm fixes from Alex Deucher:
"Dave is on vacation at the moment, so please pull these radeon and
amdgpu fixes directly.
Just a few minor things for 4.2:
- add a new radeon pci id
- fix a power management regression in amdgpu
- fix HEVC command buffer validation in amdgpu"
* 'drm-fixes-4.2' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: add new OLAND pci id
Revert "drm/amdgpu: Configure doorbell to maximum slots"
drm/amdgpu: add context buffer size check for HEVC
|
|
Signed-off-by: Suresh Thiagarajan <Suresh.Thiagarajan@pmcs.com>
Signed-off-by: Viswas G <Viswas.G@pmcs.com>
Acked-by: Jack Wang <xjtuwjp@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
In case of hw iscsi offload, an host can have N-number of active
connections. There can be IO's running on some connections which
make host->host_busy always TRUE. Now if logout from a connection
is tried then the code gets into an infinite loop as host->host_busy
is always TRUE.
iscsi_conn_teardown(....)
{
.........
/*
* Block until all in-progress commands for this connection
* time out or fail.
*/
for (;;) {
spin_lock_irqsave(session->host->host_lock, flags);
if (!atomic_read(&session->host->host_busy)) { /* OK for ERL == 0 */
spin_unlock_irqrestore(session->host->host_lock, flags);
break;
}
spin_unlock_irqrestore(session->host->host_lock, flags);
msleep_interruptible(500);
iscsi_conn_printk(KERN_INFO, conn, "iscsi conn_destroy(): "
"host_busy %d host_failed %d\n",
atomic_read(&session->host->host_busy),
session->host->host_failed);
................
...............
}
}
This is not an issue with software-iscsi/iser as each cxn is a separate
host.
Fix:
Acquiring eh_mutex in iscsi_conn_teardown() before setting
session->state = ISCSI_STATE_TERMINATE.
Signed-off-by: John Soni Jose <sony.john@avagotech.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Chris Leech <cleech@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This reverts commit 78ad5cdd21f0d614983fc397338944e797ec70b9.
This commit breaks dpm and suspend/resume on CZ.
|
|
Signed-off-by: Boyuan Zhang <boyuan.zhang@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
|
|
Add tests in tests/parse-events.c to check call-graph and time option.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1439289050-40510-4-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Introduce --show-ref-call-graph for perf report to print reference
callgraph for no callgraph event.
Here is an example.
perf report --show-ref-call-graph --stdio
# To display the perf.data header info, please use
--header/--header-only options.
#
#
# Total Lost Samples: 0
#
# Samples: 5 of event 'cpu/cpu-cycles,call-graph=fp/'
# Event count (approx.): 144985
#
# Children Self Command Shared Object Symbol
# ........ ........ ....... ................ ........................................
#
72.30% 0.00% sleep [kernel.vmlinux] [k] entry_SYSCALL_64_fastpath
|
---entry_SYSCALL_64_fastpath
|
|--22.62%-- __GI___libc_nanosleep
--77.38%-- [...]
......
# Samples: 6 of event 'cpu/instructions,call-graph=no/', show reference callgraph
# Event count (approx.): 172780
#
# Children Self Command Shared Object Symbol
# ........ ........ ....... ................ ........................................
#
73.16% 0.00% sleep [kernel.vmlinux] [k] entry_SYSCALL_64_fastpath
|
---entry_SYSCALL_64_fastpath
|
|--31.44%-- __GI___libc_nanosleep
--68.56%-- [...]
Signed-off-by: Kan Liang <kan.liang@intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1439289050-40510-3-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
This patch introduce "call-graph=no" to disable per-event callgraph.
Here is an example.
perf record -e 'cpu/cpu-cycles,call-graph=fp/,cpu/instructions,call-graph=no/' sleep 1
perf report --stdio
# To display the perf.data header info, please use
--header/--header-only options.
#
#
# Total Lost Samples: 0
#
# Samples: 6 of event 'cpu/cpu-cycles,call-graph=fp/'
# Event count (approx.): 774218
#
# Children Self Command Shared Object Symbol
# ........ ........ ....... ................ ........................................
#
61.94% 0.00% sleep [kernel.vmlinux] [k] entry_SYSCALL_64_fastpath
|
---entry_SYSCALL_64_fastpath
|
|--97.30%-- __brk
|
--2.70%-- mmap64
_dl_check_map_versions
_dl_check_all_versions
61.94% 0.00% sleep [kernel.vmlinux] [k] perf_event_mmap
|
---perf_event_mmap
|
|--97.30%-- do_brk
| sys_brk
| entry_SYSCALL_64_fastpath
| __brk
|
--2.70%-- mmap_region
do_mmap_pgoff
vm_mmap_pgoff
sys_mmap_pgoff
sys_mmap
entry_SYSCALL_64_fastpath
mmap64
_dl_check_map_versions
_dl_check_all_versions
......
# Samples: 6 of event 'cpu/instructions,call-graph=no/'
# Event count (approx.): 359692
#
# Children Self Command Shared Object Symbol
# ........ ........ ....... ................ .................................
#
89.03% 0.00% sleep [unknown] [.] 0xffff6598ffff6598
89.03% 0.00% sleep ld-2.17.so [.] _dl_resolve_conflicts
89.03% 0.00% sleep [kernel.vmlinux] [k] page_fault
Signed-off-by: Kan Liang <kan.liang@intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1439289050-40510-2-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
This patchkit adds the ability to set callgraph mode (fp, dwarf, lbr) per
event. This in term can reduce sampling overhead and the size of the
perf.data.
Here is an example.
perf record -e 'cpu/cpu-cycles,period=1000,call-graph=fp,time=1/,cpu/instructions,call-graph=lbr/' sleep 1
perf evlist -v
cpu/cpu-cycles,period=1000,call-graph=fp,time=1/: type: 4, size: 112,
config: 0x3c, { sample_period, sample_freq }: 1000, sample_type:
IP|TID|TIME|CALLCHAIN|PERIOD|IDENTIFIER, read_format: ID, disabled: 1,
inherit: 1, mmap: 1, comm: 1, enable_on_exec: 1, task: 1, sample_id_all:
1, exclude_guest: 1, mmap2: 1, comm_exec: 1
cpu/instructions,call-graph=lbr/: type: 4, size: 112, config: 0xc0, {
sample_period, sample_freq }: 4000, sample_type:
IP|TID|TIME|CALLCHAIN|PERIOD|BRANCH_STACK|IDENTIFIER, read_format: ID,
disabled: 1, inherit: 1, freq: 1, enable_on_exec: 1, sample_id_all: 1,
exclude_guest: 1
Signed-off-by: Kan Liang <kan.liang@intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1439289050-40510-1-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
"perf probe --lines sys_poll" shows only the first line of sys_poll,
because the SYSCALL_DEFINE macro:
----
SYSCALL_DEFINE*(foo,...)
{
body;
}
----
is expanded as below (on debuginfo)
----
static inline int SYSC_foo(...)
{
body;
}
int SyS_foo(...) <- is an alias of sys_foo.
{
return SYSC_foo(...);
}
----
So, "perf probe --lines sys_foo" decodes SyS_foo function and it also skips
inlined functions(SYSC_foo) inside the target function because those functions
are usually defined somewhere else.
To fix this issue, this fix checks whether the inlined function is defined at
the same point of the target function, and if so, it doesn't skip the inline
function.
Reported-by: Arnaldo Carvalho de Melo <acme@kernel.org>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/20150812012406.11811.94691.stgit@localhost.localdomain
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap
Pull regmap fix from Mark Brown:
"regmap: Fix handling of present bits on rbtree cache block resize
When expanding a cache block we use krealloc() to resize the register
present bitmap without initialising the newly allocated data (the
original code was written for kzalloc()). Add an appropraite memset()
to fix that"
* tag 'regmap-fix-v4.2-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap:
regmap: regcache-rbtree: Clean new present bits on present bitmap resize
|
|
In addition to <-, that may be repurposed for horizontal scrolling.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-w3rctelxr4yxrjufx7z3fclb@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
IS_ERR() already contains an 'unlikely' compiler flag so there is no
need to do that again from IS_ERR() callers.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Some of the device mapper targets override the error code returned by
dm_get_device() and return either -EINVAL or -ENXIO. There is nothing
gained by this override. It is better to propagate the returned error
code unchanged to caller.
This work was motivated by hitting an issue where the underlying device
was busy but -EINVAL was being returned. After this change we get
-EBUSY instead and it is easier to figure out the problem.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
In properly written code we should not assume that DM_MAPIO_SUBMITTED is
zero. We should test the return value for DM_MAPIO_SUBMITTED rather than
testing it for zero.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Since commit 003b5c571 ("block: Convert drivers to immutable biovecs"),
vec_mempool in struct dm_verity is no longer used. Remove it and
related definitions.
Signed-off-by: Sami Tolvanen <samitolvanen@google.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
This stops spurious wake ups from calls to prealloc_free_structs().
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
rebalance_children() calls get_nr_entries() and assigns the result to an
unused local 'child_entries' variable. Remove get_nr_entries() and
cleanup rebalance_children() accordingly.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
We no longer sleep in any of the smq functions, so this can become a
spinlock. Switching from mutex to spinlock improves performance when
the fast cache device is a very low latency device (e.g. NVMe SSD).
The switch to spinlock also allows for removal of the extra tick_lock;
which is no longer needed since the main lock being a spinlock now
fulfills the locking requirements needed by interrupt context.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
When creating dm-cache with the default policy, it will call
request_module("dm-cache-default") to register the default policy.
But the "dm-cache-default" alias was left referring to the MQ policy.
Fix this by moving the module alias to SMQ.
Fixes: bccab6a0 (dm cache: switch the "default" cache replacement policy from mq to smq)
Signed-off-by: Yi Zhang <yizhan@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
