| Age | Commit message (Collapse) | Author |
|---|
|
x200 does not enable any way to programmatically obtain bus clock
speed. Bclk for the architecture has a fixed value of 100 MHz.
At the same time x200 cannot be included in has_snb_msrs since
it does not support C7 idle state.
prior to this patch, MHz values reported on this chip
were erroneously calculated using bclk of 133MHz,
causing MHz values to be reported 33% higher than actual.
Signed-off-by: Hubert Chrzaniuk <hubert.chrzaniuk@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
turbostat -i interval_sec
will sample and display statistics every interval_sec.
interval_sec used to be a whole number of seconds,
but now we accept a decimal, as small as 0.001 sec (1 ms).
Signed-off-by: Len Brown <len.brown@intel.com>
|
|
Pull block merge fix from Jens Axboe.
This fixes the block segment counting bug and resulting sg overrun
reported by Kent Overstreet, introduced with the last block pull.
* 'for-linus' of git://git.kernel.dk/linux-block:
block: don't optimize for non-cloned bio in bio_get_last_bvec()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"This fixes 3 FPU handling related bugs, an EFI boot crash and a
runtime warning.
The EFI fix arrived late but I didn't want to delay it to after v4.5
because the effects are pretty bad for the systems that are affected
by it"
[ Actually, I don't think the EFI fix really matters yet, because we
haven't switched to the separate EFI page tables in mainline yet ]
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/efi: Fix boot crash by always mapping boot service regions into new EFI page tables
x86/fpu: Fix eager-FPU handling on legacy FPU machines
x86/delay: Avoid preemptible context checks in delay_mwaitx()
x86/fpu: Revert ("x86/fpu: Disable AVX when eagerfpu is off")
x86/fpu: Fix 'no387' regression
|
|
If data_err=abort option is specified for an ext3/ext4 mount,
/proc/mounts does show it as "(null)". This is caused by token2str()
returning NULL for Opt_data_err_abort (due to its pattern containing
'=').
Signed-off-by: Ales Novak <alnovak@suse.cz>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
ext4_reserve_inode_write() in ext4_mark_inode_dirty() could fail on
error (e.g. EIO) and iloc.bh can be NULL in this case. But the error is
ignored in the following "if" condition and ext4_expand_extra_isize()
might be called with NULL iloc.bh set, which triggers NULL pointer
dereference.
This is uncovered by commit 8b4953e13f4c ("ext4: reserve code points for
the project quota feature"), which enlarges the ext4_inode size, and
run the following script on new kernel but with old mke2fs:
#/bin/bash
mnt=/mnt/ext4
devname=ext4-error
dev=/dev/mapper/$devname
fsimg=/home/fs.img
trap cleanup 0 1 2 3 9 15
cleanup()
{
umount $mnt >/dev/null 2>&1
dmsetup remove $devname
losetup -d $backend_dev
rm -f $fsimg
exit 0
}
rm -f $fsimg
fallocate -l 1g $fsimg
backend_dev=`losetup -f --show $fsimg`
devsize=`blockdev --getsz $backend_dev`
good_tab="0 $devsize linear $backend_dev 0"
error_tab="0 $devsize error $backend_dev 0"
dmsetup create $devname --table "$good_tab"
mkfs -t ext4 $dev
mount -t ext4 -o errors=continue,strictatime $dev $mnt
dmsetup load $devname --table "$error_tab" && dmsetup resume $devname
echo 3 > /proc/sys/vm/drop_caches
ls -l $mnt
exit 0
[ Patch changed to simplify the function a tiny bit. -- Ted ]
Signed-off-by: Eryu Guan <guaneryu@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
|
Pull SCSI target bug fix from Nicholas Bellinger:
"Here is an outstanding target-core bug-fix for v4.5 code."
This patch addresses a recent Task Management (TMR) regression related
to larger set of multi-port LUN_RESET bug-fixes in v4.5-rc5.
It drops a left-over target_put_sess_cmd() of se_cmd->cmd_kref within
ABORT_TASK failure path, once a se_cmd descriptor has already
completed posting response to fabric driver logic, and must be skipped
during normal ABORT_TASK se_cmd->tag lookup"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
target: Drop incorrect ABORT_TASK put for completed commands
|
|
For !BIO_CLONED bio, we can use .bi_vcnt safely, but it
doesn't mean we can just simply return .bi_io_vec[.bi_vcnt - 1]
because the start postion may have been moved in the middle of
the bvec, such as splitting in the middle of bvec.
Fixes: 7bcd79ac50d9(block: bio: introduce helpers to get the 1st and last bvec)
Cc: stable@vger.kernel.org
Reported-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Requested-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
A few new AVX-512 instruction groups/features are added in cpufeatures.h
for enuermation: AVX512DQ, AVX512BW, and AVX512VL.
Clear the flags in fpu__xstate_clear_all_cpu_caps().
The specification for latest AVX-512 including the features can be found at:
https://software.intel.com/sites/default/files/managed/07/b7/319433-023.pdf
Note, I didn't enable the flags in KVM. Hopefully the KVM guys can pick up
the flags and enable them in KVM.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Ravi V Shankar <ravi.v.shankar@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm@vger.kernel.org
Link: http://lkml.kernel.org/r/1457667498-37357-1-git-send-email-fenghua.yu@intel.com
[ Added more detailed feature descriptions. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
page tables
Some machines have EFI regions in page zero (physical address
0x00000000) and historically that region has been added to the e820
map via trim_bios_range(), and ultimately mapped into the kernel page
tables. It was not mapped via efi_map_regions() as one would expect.
Alexis reports that with the new separate EFI page tables some boot
services regions, such as page zero, are not mapped. This triggers an
oops during the SetVirtualAddressMap() runtime call.
For the EFI boot services quirk on x86 we need to memblock_reserve()
boot services regions until after SetVirtualAddressMap(). Doing that
while respecting the ownership of regions that may have already been
reserved by the kernel was the motivation behind this commit:
7d68dc3f1003 ("x86, efi: Do not reserve boot services regions within reserved areas")
That patch was merged at a time when the EFI runtime virtual mappings
were inserted into the kernel page tables as described above, and the
trick of setting ->numpages (and hence the region size) to zero to
track regions that should not be freed in efi_free_boot_services()
meant that we never mapped those regions in efi_map_regions(). Instead
we were relying solely on the existing kernel mappings.
Now that we have separate page tables we need to make sure the EFI
boot services regions are mapped correctly, even if someone else has
already called memblock_reserve(). Instead of stashing a tag in
->numpages, set the EFI_MEMORY_RUNTIME bit of ->attribute. Since it
generally makes no sense to mark a boot services region as required at
runtime, it's pretty much guaranteed the firmware will not have
already set this bit.
For the record, the specific circumstances under which Alexis
triggered this bug was that an EFI runtime driver on his machine was
responding to the EVT_SIGNAL_VIRTUAL_ADDRESS_CHANGE event during
SetVirtualAddressMap().
The event handler for this driver looks like this,
sub rsp,0x28
lea rdx,[rip+0x2445] # 0xaa948720
mov ecx,0x4
call func_aa9447c0 ; call to ConvertPointer(4, & 0xaa948720)
mov r11,QWORD PTR [rip+0x2434] # 0xaa948720
xor eax,eax
mov BYTE PTR [r11+0x1],0x1
add rsp,0x28
ret
Which is pretty typical code for an EVT_SIGNAL_VIRTUAL_ADDRESS_CHANGE
handler. The "mov r11, QWORD PTR [rip+0x2424]" was the faulting
instruction because ConvertPointer() was being called to convert the
address 0x0000000000000000, which when converted is left unchanged and
remains 0x0000000000000000.
The output of the oops trace gave the impression of a standard NULL
pointer dereference bug, but because we're accessing physical
addresses during ConvertPointer(), it wasn't. EFI boot services code
is stored at that address on Alexis' machine.
Reported-by: Alexis Murzeau <amurzeau@gmail.com>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Raphael Hertzog <hertzog@debian.org>
Cc: Roger Shimizu <rogershimizu@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1457695163-29632-2-git-send-email-matt@codeblueprint.co.uk
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=815125
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
i486 derived cores like Intel Quark support only the very old,
legacy x87 FPU (FSAVE/FRSTOR, CPUID bit FXSR is not set), and
our FPU code wasn't handling the saving and restoring there
properly in the 'eagerfpu' case.
So after we made eagerfpu the default for all CPU types:
58122bf1d856 x86/fpu: Default eagerfpu=on on all CPUs
these old FPU designs broke. First, Andy Shevchenko reported a splat:
WARNING: CPU: 0 PID: 823 at arch/x86/include/asm/fpu/internal.h:163 fpu__clear+0x8c/0x160
which was us trying to execute FXRSTOR on those machines even though
they don't support it.
After taking care of that, Bryan O'Donoghue reported that a simple FPU
test still failed because we weren't initializing the FPU state properly
on those machines.
Take care of all that.
Reported-and-tested-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Quentin Casasnovas <quentin.casasnovas@oracle.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yu-cheng <yu-cheng.yu@intel.com>
Link: http://lkml.kernel.org/r/20160311113206.GD4312@pd.tnic
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Return error immediately to simplify the control flow in pci_create_attr().
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
If sysfs_create_bin_file() fails, pci_create_attr() leaks the struct
bin_attribute it allocated previously.
Free the struct bin_attribute if pci_create_attr() fails.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The value of pdev->rom_attr is the definitive indicator of the fact that
we're created a sysfs attribute. Check that rather than rom_size, which is
only used incidentally when deciding whether to create a sysfs attribute.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The IORESOURCE_ROM_COPY and IORESOURCE_ROM_BIOS_COPY bits are unused.
Remove them and code that depends on them.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
resource
Loongson 3 used the IORESOURCE_ROM_COPY flag for its ROM resource. There
are two problems with this:
- When IORESOURCE_ROM_COPY is set, pci_map_rom() assumes the resource
contains virtual addresses, so it doesn't ioremap the resource. This
implies loongson_sysconf.vgabios_addr is a virtual address. That's a
problem because resources should contain CPU *physical* addresses not
virtual addresses.
- When IORESOURCE_ROM_COPY is set, pci_cleanup_rom() calls kfree() on the
resource. We did not kmalloc() the loongson_sysconf.vgabios_addr area,
so it is incorrect to kfree() it.
If we're using a shadow copy in RAM for the Loongson 3 VGA BIOS area,
disable the ROM BAR and release the address space it was consuming.
Use IORESOURCE_ROM_SHADOW instead of IORESOURCE_ROM_COPY. This means the
struct resource contains CPU physical addresses, and pci_map_rom() will
ioremap() it as needed.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Use a temporary struct resource pointer to avoid needless repetition of
"pdev->resource[PCI_ROM_RESOURCE]". No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
A struct resource contains CPU physical addresses, not virtual addresses.
But sn_acpi_slot_fixup() and sn_io_slot_fixup() stored the virtual address
of a shadow ROM copy in the resource. To compensate, pci_map_rom() had a
special case that returned the resource address directly rather than
calling ioremap() on it.
When we're using a shadow copy in RAM or PROM, disable the ROM BAR and
release the address space it was consuming.
Store the CPU physical (not virtual) address in the shadow ROM resource,
and mark the resource as IORESOURCE_ROM_SHADOW so we use the normal
pci_map_rom() path that ioremaps the copy.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Depositing __IA64_UNCACHED_OFFSET in the upper address bits is essentially
equivalent to ioremap(): it converts a CPU physical address to a virtual
address using the ia64 uncacheable identity map.
Call ioremap() instead of doing the phys-to-virt conversion manually with
__IA64_UNCACHED_OFFSET.
Note that this makes it obvious that (a) we're putting a virtual address in
a struct resource, and (b) we're passing a virtual address to ioremap()
below in the PCI_ROM_RESOURCE case. These are both pre-existing problems
that I'll resolve next.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Use a temporary struct resource pointer to avoid needless repetition of
"dev->resource[idx]". No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Remove unnecessary indentation in pci_map_rom(). This is logically part of
the previous patch; I split it out to make the critical changes in that
patch more obvious. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
When pci_create_sysfs_dev_files() created the "rom" sysfs file, it set the
sysfs file size to the actual size of a ROM BAR, or if there was no ROM BAR
but the platform provided a shadow copy in RAM, to 0x20000. 0x20000 is an
arch-specific length that should not be baked into the PCI core.
Every place that sets IORESOURCE_ROM_SHADOW also sets the size of the
PCI_ROM_RESOURCE, so use the resource length always.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Modify the documentation to match the actual parameter as implemented in
kernel/module.c:273.
Signed-off-by: James Johnston <johnstonj.public@codenest.com>
Reviewed-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Some of platforms like Nvidia's Tegra210 Jetson-TX1 platform has
multiple PMW based regulators. Add support to have multiple instances
of the driver by not changing any global data of pwm regulator and
if required, making instance specific copy and then making changes.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
With following equation for calculating
voltage_to_duty_cycle_percentage
100 - (((req_uV * 100) - (min_uV * 100)) / diff);
we get 0% for max_uV and 100% for min_uV.
Correcting this to
((req_uV * 100) - (min_uV * 100)) / diff;
to get proper duty cycle.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
OF interface provides to read the u32 value via standard interface
of_property_read_u32(). Use this API to read "regulator-min-microvolts"
and "regulator-max-microvolt".
This will make consistent with other property value reads.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Pull MTD fixes from Brian Norris:
"Late MTD fix for v4.5:
- A simple error code handling fix for the NAND ECC test; this was a
regression in v4.5-rc1
- A MAINTAINERS update, which might as well go in ASAP"
* tag 'for-linus-20160311' of git://git.infradead.org/linux-mtd:
MAINTAINERS: add a maintainer for the NAND subsystem
mtd: nand: tests: fix regression introduced in mtd_nandectest
|
|
Pull drm/i915 fixes from Dave Airlie:
"Just two i915 regression fixes, that should be it from me"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Actually retry with bit-banging after GMBUS timeout
drm/i915: Fix bogus dig_port_map[] assignment for pre-HSW
|
|
When removing an element from the mempool, mark it as unpoisoned in KASAN
before verifying its contents for SLUB/SLAB debugging. Otherwise KASAN
will flag the reads checking the element use-after-free writes as
use-after-free reads.
Signed-off-by: Matthew Dawson <matthew@mjdsystems.ca>
Acked-by: Andrey Ryabinin <aryabinin@virtuozzo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The cavium,pci-thunder-ecam devices are exactly ECAM-based PCI root
complexes. These root complexes (loosely referred to as ECAM units in the
hardware manuals) are used to access the Thunder on-chip devices. They
are special in that all the BARs on devices behind these root complexes are
at fixed addresses.
Add a driver for these devices that synthesizes Enhanced Allocation (EA)
capability entries for each BAR.
Since this EA synthesis is needed for exactly two chip models, we can hard-
code some assumptions about the device topology and the layout of the
config space of specific DEVFNs in the driver.
[bhelgaas: changelog, whitespace]
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
|
|
The root complexes used to access off-chip PCIe devices (called PEM units
in the hardware manuals) on some Cavium ThunderX processors require quirky
access methods for the config space of the PCIe bridge.
Add a driver to provide these config space accessor functions. Use the
pci-host-common code to configure the PCI machinery.
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
|
|
Move pci_host_common_probe() and associated functions to pci-host-common.c,
where it can be shared with other drivers. Make it public (not static)
and update Kconfig and Makefile to build it. No functional change
intended.
[bhelgaas: split into separate patch, changelog]
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Will Deacon <will.deacon@arm.com>
|
|
Factor gen_pci_probe(), moving most of it into pci_host_common_probe()
where it can be shared with other drivers that have slightly different
config accessors. No functional change intended.
[bhelgaas: split into separate patch, changelog]
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Will Deacon <will.deacon@arm.com>
|
|
Move definitions for generic PCI host controller driver structures to a
separate header file so we can share them with other drivers. No
functional change intended.
[bhelgaas: split into separate patch, changelog]
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Will Deacon <will.deacon@arm.com>
|
|
Commit 0a927c2f02 ("dm thin: return -ENOSPC when erroring retry list due
to out of data space") was a step in the right direction but didn't go
far enough.
Add a new 'out_of_data_space' flag to 'struct pool' and set it if/when
the pool runs of of data space. This fixes cell_error() and
error_retry_list() to not blindly return -EIO.
We cannot rely on the 'error_if_no_space' feature flag since it is
transient (in that it can be reset once space is added, plus it only
controls whether errors are issued, it doesn't reflect whether the
pool is actually out of space).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"Two more fixes for 4.5:
- One is a fix for OMAP that is urgently needed to avoid DRA7xx chips
from premature aging, by always keeping the Ethernet clock enabled.
- The other solves a I/O memory layout issue on Armada, where SROM
and PCI memory windows were conflicting in some configurations"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: mvebu: fix overlap of Crypto SRAM with PCIe memory window
ARM: dts: dra7: do not gate cpsw clock due to errata i877
ARM: OMAP2+: hwmod: Introduce ti,no-idle dt property
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fix from Mauro Carvalho Chehab:
"One last time fix: It adds a code that prevents some media tools like
media-ctl to hide some entities that have their IDs out of the range
expected by those apps"
* tag 'media/v4.5-5' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] media-device: map new functions into old types for legacy API
|
|
When the Crypto SRAM mappings were added to the Device Tree files
describing the Armada XP boards in commit c466d997bb16 ("ARM: mvebu:
define crypto SRAM ranges for all armada-xp boards"), the fact that
those mappings were overlaping with the PCIe memory aperture was
overlooked. Due to this, we currently have for all Armada XP platforms
a situation that looks like this:
Memory mapping on Armada XP boards with internal registers at
0xf1000000:
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf8000000 -> 0xffe0000 126M PCIe memory aperture
- 0xf8100000 -> 0xf8110000 64KB Crypto SRAM #0 => OVERLAPS WITH PCIE !
- 0xf8110000 -> 0xf8120000 64KB Crypto SRAM #1 => OVERLAPS WITH PCIE !
- 0xffe00000 -> 0xfff00000 1M PCIe I/O aperture
- 0xfff0000 -> 0xffffffff 1M BootROM
The overlap means that when PCIe devices are added, depending on their
memory window needs, they might or might not be mapped into the
physical address space. Indeed, they will not be mapped if the area
allocated in the PCIe memory aperture by the PCI core overlaps with
one of the Crypto SRAM. Typically, a Intel IGB PCIe NIC that needs 8MB
of PCIe memory will see its PCIe memory window allocated from
0xf80000000 for 8MB, which overlaps with the Crypto SRAM windows. Due
to this, the PCIe window is not created, and any attempt to access the
PCIe window makes the kernel explode:
[ 3.302213] igb: Copyright (c) 2007-2014 Intel Corporation.
[ 3.307841] pci 0000:00:09.0: enabling device (0140 -> 0143)
[ 3.313539] mvebu_mbus: cannot add window '4:f8', conflicts with another window
[ 3.320870] mvebu-pcie soc:pcie-controller: Could not create MBus window at [mem 0xf8000000-0xf87fffff]: -22
[ 3.330811] Unhandled fault: external abort on non-linefetch (0x1008) at 0xf08c0018
This problem does not occur on Armada 370 boards, because we use the
following memory mapping (for boards that have internal registers at
0xf1000000):
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0 => OK !
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
Obviously, the solution is to align the location of the Crypto SRAM
mappings of Armada XP to be similar with the ones on Armada 370, i.e
have them between the "internal registers" area and the beginning of
the PCIe aperture.
However, we have a special case with the OpenBlocks AX3-4 platform,
which has a 128 MB NOR flash. Currently, this NOR flash is mapped from
0xf0000000 to 0xf8000000. This is possible because on OpenBlocks
AX3-4, the internal registers are not at 0xf1000000. And this explains
why the Crypto SRAM mappings were not configured at the same place on
Armada XP.
Hence, the solution is two-fold:
(1) Move the NOR flash mapping on Armada XP OpenBlocks AX3-4 from
0xe8000000 to 0xf0000000. This frees the 0xf0000000 ->
0xf80000000 space.
(2) Move the Crypto SRAM mappings on Armada XP to be similar to
Armada 370 (except of course that Armada XP has two Crypto SRAM
and not one).
After this patch, the memory mapping on Armada XP boards with
registers at 0xf1 is:
- 0x00000000 -> 0xf0000000 3.75G RAM
- 0xf0000000 -> 0xf1000000 16M NOR flashes (AXP GP / AXP DB)
- 0xf1000000 -> 0xf1100000 1M internal registers
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0
- 0xf1110000 -> 0xf1120000 64KB Crypto SRAM #1
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
And the memory mapping for the special case of the OpenBlocks AX3-4
(internal registers at 0xd0000000, NOR of 128 MB):
- 0x00000000 -> 0xc0000000 3G RAM
- 0xd0000000 -> 0xd1000000 1M internal registers
- 0xe800000 -> 0xf0000000 128M NOR flash
- 0xf1100000 -> 0xf1110000 64KB Crypto SRAM #0
- 0xf1110000 -> 0xf1120000 64KB Crypto SRAM #1
- 0xf8000000 -> 0xffe0000 126M PCIe memory
- 0xffe00000 -> 0xfff00000 1M PCIe I/O
- 0xfff0000 -> 0xffffffff 1M BootROM
Fixes: c466d997bb16 ("ARM: mvebu: define crypto SRAM ranges for all armada-xp boards")
Reported-by: Phil Sutter <phil@nwl.cc>
Cc: Phil Sutter <phil@nwl.cc>
Cc: <stable@vger.kernel.org>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Pull dmaengine fixes from Vinod Koul:
"Two fixes showed up in last few days, and they should be included in
4.5. Summary:
Two more late fixes to drivers, nothing major here:
- A memory leak fix in fsdma unmap the dma descriptors on freeup
- A fix in xdmac driver for residue calculation of dma descriptor"
* tag 'dmaengine-fix-4.5' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: at_xdmac: fix residue computation
dmaengine: fsldma: fix memory leak
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"Two more fixes for issues introduced recently, one in the generic
device properties framework and one in ACPICA.
Specifics:
- Revert a recent ACPICA commit that has been reverted upstream,
because it caused problems to happen on user systems and the
problem it attempted to address will not be relevant any more after
upcoming ACPI specification changes (Bob Moore).
- Fix crash in the generic device properties framework introduced by
a recent change that forgot to check pointers against error values
in addition to checking them against NULL (Heikki Krogerus)"
* tag 'pm+acpi-4.5-final' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
device property: fwnode->secondary may contain ERR_PTR(-ENODEV)
ACPICA: Revert "Parser: Fix for SuperName method invocation"
|
|
Add PCIe Root Port driver for Xilinx PCIe NWL bridge IP.
[bhelgaas: wait for link like dw_pcie_wait_for_link(), simplify bitmap
error path, typos, whitespace, fold in Dan Carpenter's PTR_ERR() fix]
Signed-off-by: Bharat Kumar Gogada <bharatku@xilinx.com>
Signed-off-by: Ravi Kiran Gummaluri <rgummal@xilinx.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
|
|
A SerDes PHY is optional, so if devm_phy_get() doesn't find one at all,
that's fine. But if devm_phy_get() finds a PHY that doesn't have a driver
yet, it returns -EPROBE_DEFER. In that case, defer probing the Keystone
driver. We may be able to load it later after a PHY driver is loaded.
[bhelgaas: changelog, check for -EPROBE_DEFER first]
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"This is a fix for a regression introduced in 4.5-rc1 by the new torn
log write detection code. The regression only affects people moving a
clean filesystem between machines/kernels of different architecture
(such as changing between 32 bit and 64 bit kernels), but this is the
recommended (and only!) safe way to migrate a filesystem between
architectures so we really need to ensure it works.
The changes are larger than I'd prefer right at the end of the release
cycle, but the majority of the change is just factoring code to enable
the detection of a clean log at the correct time to avoid this issue.
Changes:
- Only perform torn log write detection on dirty logs. This prevents
failures being detected due to a clean filesystem being moved
between machines or kernels of different architectures (e.g. 32 ->
64 bit, BE -> LE, etc). This fixes a regression introduced by the
torn log write detection in 4.5-rc1"
* tag 'xfs-for-linus-4.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: only run torn log write detection on dirty logs
xfs: refactor in-core log state update to helper
xfs: refactor unmount record detection into helper
xfs: separate log head record discovery from verification
|
|
Originally altera_pcie_link_is_up() decided the link was up if any of the
low four bits of the LTSSM register were set. But the link is only up if
the LTSSM state is L0, so check for that exact value.
[bhelgaas: changelog]
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs
Pull vfs fixes from Al Viro:
"A couple of fixes: Fix for my dumb braino in ncpfs and a long-standing
breakage on recovery from failed rename() in jffs2"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
jffs2: reduce the breakage on recovery from halfway failed rename()
ncpfs: fix a braino in OOM handling in ncp_fill_cache()
|
|
Make the R-Car drivers depend on ARCH_RENESAS instead of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS. The motivation is that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM-based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The single pinmux controller can be cascaded to the other interrupt
controllers. Hence when propagating wake-up settings to its parent
interrupt controller, there's possiblity of detecting possible recursive
locking and getting lockdep warning.
This patch avoids this false positive by using a separate lockdep class
for this single pinctrl interrupts.
Cc: linux-gpio@vger.kernel.org
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Based on the Allwinner A64 user manual and on the previous sunxi
pinctrl drivers this introduces the pin multiplex assignments for
the ARMv8 Allwinner A64 SoC.
Port A is apparently used for the fixed function DRAM controller, so
the ports start at B here (the manual mentions "n from 1 to 7", so
not starting at 0).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
* device-properties-fixes:
device property: fwnode->secondary may contain ERR_PTR(-ENODEV)
* acpica-fixes:
ACPICA: Revert "Parser: Fix for SuperName method invocation"
|
