| Age | Commit message (Collapse) | Author |
|---|
|
My previous fix to clear padding of short frames used skb->len as the
DMA length, assuming that skb_padto() extended skb->len to include the
padding. That isn't the case; we need to use skb_put_padto() instead.
(This wasn't immediately obvious because software padding isn't
actually needed on the R-Car H2. We could make it conditional on
which chip is being driven, but it's probably not worth the effort.)
Reported-by: "Violeta Menéndez González" <violeta.menendez@codethink.co.uk>
Fixes: 612a17a54b50 ("sh_eth: Fix padding of short frames on TX")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit fd9af07c3404ac9ecbd0d859563360f51ce1ffde.
The hardware manual states that the frame error and multicast bits are
copied to bits 9:0 of RD0, not bits 25:16. I've tested that this is
true for RFS1 (CRC error), RFS3 (frame too short), RFS4 (frame too
long) and RFS8 (multicast).
Also adjust a comment to agree with this.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of RX ring underrun (RDE), we attempt to reset the software
descriptor pointers (dirty_rx and cur_rx) to match where the hardware
will read the next descriptor from, as that might not be the first
dirty descriptor. This relies on reading RDFAR, but that register
doesn't exist on all supported chips - specifically, not on the R-Car
chips. This will result in unpredictable behaviour on those chips
after an RDE.
Make this pointer reset conditional and assume that it isn't needed on
the R-Car chips. This fix also assumes that RDFAR is never exposed at
offset 0 in the memory map - this is currently true, and a subsequent
commit will fix the ambiguity between offset 0 and no-offset in the
register offset maps.
Fixes: 79fba9f51755 ("net: sh_eth: fix the rxdesc pointer when rx ...")
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When submitting a DMA descriptor, the active bit must be written last.
When reading a completed DMA descriptor, the active bit must be read
first.
Add memory barriers to ensure that this ordering is maintained.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Enable disabled interrupt, on unsuccessful operation.
Found by Coccinelle.
Signed-off-by: Tapasweni Pathak <tapaswenipathak@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Currently the guest exit trace event saves the VCPU pointer to the
structure, and the guest PC is retrieved by dereferencing it when the
event is printed rather than directly from the trace record. This isn't
safe as the printing may occur long afterwards, after the PC has changed
and potentially after the VCPU has been freed. Usually this results in
the same (wrong) PC being printed for multiple trace events. It also
isn't portable as userland has no way to access the VCPU data structure
when interpreting the trace record itself.
Lets save the actual PC in the structure so that the correct value is
accessible later.
Fixes: 669e846e6c4e ("KVM/MIPS32: MIPS arch specific APIs for KVM")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: <stable@vger.kernel.org> # v3.10+
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"Two GPIO fixes:
- Fix a translation problem in of_get_named_gpiod_flags()
- Fix a long standing container_of() mistake in the TPS65912 driver"
* tag 'gpio-v4.0-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: tps65912: fix wrong container_of arguments
gpiolib: of: allow of_gpiochip_find_and_xlate to find more than one chip per node
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal management fixes from Eduardo Valentin:
"Specifics:
- Several fixes in tmon tool.
- Fixes in intel int340x for _ART and _TRT tables.
- Add id for Avoton SoC into powerclamp driver.
- Fixes in RCAR thermal driver to remove race conditions and fix fail
path
- Fixes in TI thermal driver: removal of unnecessary code and build
fix if !CONFIG_PM_SLEEP
- Cleanups in exynos thermal driver
- Add stubs for include/linux/thermal.h. Now drivers using thermal
calls but that also work without CONFIG_THERMAL will be able to
compile for systems that don't care about thermal.
Note: I am sending this pull on Rui's behalf while he fixes issues in
his Linux box"
* 'fixes-for-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: int340x_thermal: Ignore missing _ART, _TRT tables
thermal/intel_powerclamp: add id for Avoton SoC
tools/thermal: tmon: silence 'set but not used' warnings
tools/thermal: tmon: use pkg-config to determine library dependencies
tools/thermal: tmon: support cross-compiling
tools/thermal: tmon: add .gitignore
tools/thermal: tmon: fixup tui windowing calculations
tools/thermal: tmon: tui: don't hard-code dialog window size assumptions
tools/thermal: tmon: add min/max macros
tools/thermal: tmon: add --target-temp parameter
thermal: exynos: Clean-up code to use oneline entry for exynos compatible table
thermal: rcar: Make error and remove paths symmetrical with init
thermal: rcar: Fix race condition between init and interrupt
thermal: Introduce dummy functions when thermal is not defined
ti-soc-thermal: Delete an unnecessary check before the function call "cpufreq_cooling_unregister"
thermal: ti-soc-thermal: bandgap: Fix build warning if !CONFIG_PM_SLEEP
|
|
In commit b4eef9b36db4, we started to use hwapic_isr_update() != NULL
instead of kvm_apic_vid_enabled(vcpu->kvm). This didn't work because
SVM had it defined and "apicv" path in apic_{set,clear}_isr() does not
change apic->isr_count, because it should always be 1. The initial
value of apic->isr_count was based on kvm_apic_vid_enabled(vcpu->kvm),
which is always 0 for SVM, so KVM could have injected interrupts when it
shouldn't.
Fix it by implicitly setting SVM's hwapic_isr_update to NULL and make the
initial isr_count depend on hwapic_isr_update() for good measure.
Fixes: b4eef9b36db4 ("kvm: x86: vmx: NULL out hwapic_isr_update() in case of !enable_apicv")
Reported-and-tested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
Pull md fixes from Neil Brown:
"Three md fixes:
- fix a read-balance problem that was reported 2 years ago, but that
I never noticed the report :-(
- fix for rare RAID6 problem causing incorrect bitmap updates when
two devices fail.
- add __ATTR_PREALLOC annotation now that it is possible"
* tag 'md/4.0-fixes' of git://neil.brown.name/md:
md: mark some attributes as pre-alloc
raid5: check faulty flag for array status during recovery.
md/raid1: fix read balance when a drive is write-mostly.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull arch/metag fix from James Hogan:
"This is just a single patch to fix the KSTK_EIP() and KSTK_ESP()
macros for metag which have always been erronously returning the PC
and stack pointer of the task's kernel context rather than from its
user context saved at entry from userland into the kernel, which
affects the contents of /proc/<pid>/maps and /proc/<pid>/stat"
* tag 'metag-fixes-v4.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
metag: Fix KSTK_EIP() and KSTK_ESP() macros
|
|
Or Gerlitz says:
====================
Mellanox driver fixes
Two small fixes, please apply to net.
Both patches should go to 3.19.y too.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Packets which are sent from the selftest (ethtool) flow,
should not be passed to GRO stack but rather dropped by
the driver after validation. To achieve that, we disable
GRO for the duration of the selftest.
Fixes: dd65beac48a5 ("net/mlx4_en: Extend usage of napi_gro_frags")
Reported-by: Carol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bit mask for currently supported driver features (MLX4_UPDATE_QP_SUPPORTED_ATTRS)
of the update-qp command was defined twice (using enum value and pre-processor
define directive) and wrong.
The return value of the call to mlx4_update_qp() from within the SRIOV
resource-tracker was wrongly voided down.
Fix both issues.
issue: none
Fixes: 09e05c3f78e9 ('net/mlx4: Set vlan stripping policy by the right command')
Fixes: ce8d9e0d6746 ('net/mlx4_core: Add UPDATE_QP SRIOV wrapper support')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"A CR4-shadow 32-bit init fix, plus two typo fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86: Init per-cpu shadow copy of CR4 on 32-bit CPUs too
x86/platform/intel-mid: Fix trivial printk message typo in intel_mid_arch_setup()
x86/cpu/intel: Fix trivial typo in intel_tlb_table[]
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"Three clockevents/clocksource driver fixes"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: pxa: Fix section mismatch
clocksource: mtk: Fix race conditions in probe code
clockevents: asm9260: Fix compilation error with sparc/sparc64 allyesconfig
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fixes from Ingo Molnar:
"Two kprobes fixes and a handful of tooling fixes"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf tools: Make sparc64 arch point to sparc
perf symbols: Define EM_AARCH64 for older OSes
perf top: Fix SIGBUS on sparc64
perf tools: Fix probing for PERF_FLAG_FD_CLOEXEC flag
perf tools: Fix pthread_attr_setaffinity_np build error
perf tools: Define _GNU_SOURCE on pthread_attr_setaffinity_np feature check
perf bench: Fix order of arguments to memcpy_alloc_mem
kprobes/x86: Check for invalid ftrace location in __recover_probed_insn()
kprobes/x86: Use 5-byte NOP when the code might be modified by ftrace
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fix from Ingo Molnar:
"An rtmutex deadlock path fixlet"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
locking/rtmutex: Set state back to running on error
|
|
Florian Fainelli says:
====================
net: bcmgenet and systemport statistics fixes
This two patches fix a similar problem in the GENET and SYSTEMPORT drivers
for software maintained statistics used to track DMA mapping and SKB
re-allocation failures.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 60b4ea1781fd ("net: systemport: log RX buffer allocation and RX/TX DMA
failures") added a few software maintained statistics using
BCM_SYSPORT_STAT_MIB_RX and BCM_SYSPORT_STAT_MIB_TX. These statistics are read
from the hardware MIB counters, such that bcm_sysport_update_mib_counters() was
trying to read from a non-existing MIB offset for these counters.
Fix this by introducing a special type: BCM_SYSPORT_STAT_SOFT, similar to
BCM_SYSPORT_STAT_NETDEV, such that bcm_sysport_get_ethtool_stats will read from
the software mib.
Fixes: 60b4ea1781fd ("net: systemport: log RX buffer allocation and RX/TX DMA failures")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 44c8bc3ce39f ("net: bcmgenet: log RX buffer allocation and RX/TX dma
failures") added a few software maintained statistics using
BCMGENET_STAT_MIB_RX and BCMGENET_STAT_MIB_TX. These statistics are read from
the hardware MIB counters, such that bcmgenet_update_mib_counters() was trying
to read from a non-existing MIB offset for these counters.
Fix this by introducing a special type: BCMGENET_STAT_SOFT, similar to
BCMGENET_STAT_NETDEV, such that bcmgenet_get_ethtool_stats will read from the
software mib.
Fixes: 44c8bc3ce39f ("net: bcmgenet: log RX buffer allocation and RX/TX dma failures")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
rxrpc_resend_timeout has an initial value of 4 * HZ; use it as-is.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Typo, 'stop' is never set to true.
Seems intent is to not attempt to retransmit more packets after sendmsg
returns an error.
This change is based on code inspection only.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
interface.
To repeat:
$ sudo ip link del hsr0
BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
IP: [<ffffffff8187f495>] hsr_del_port+0x15/0xa0
etc...
Bug description:
As part of the hsr master device destruction, hsr_del_port() is called for each of
the hsr ports. At each such call, the master device is updated regarding features
and mtu. When the master device is freed before the slave interfaces, master will
be NULL in hsr_del_port(), which led to a NULL pointer dereference.
Additionally, dev_put() was called on the master device itself in hsr_del_port(),
causing a refcnt error.
A third bug in the same code path was that the rtnl lock was not taken before
hsr_del_port() was called as part of hsr_dev_destroy().
The reporter (Nicolas Dichtel) also said: "hsr_netdev_notify() supposes that the
port will always be available when the notification is for an hsr interface. It's
wrong. For example, netdev_wait_allrefs() may resend NETDEV_UNREGISTER.". As a
precaution against this, a check for port == NULL was added in hsr_dev_notify().
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Fixes: 51f3c605318b056a ("net/hsr: Move slave init to hsr_slave.c.")
Signed-off-by: Arvid Brodin <arvid.brodin@alten.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use timer API functions setup_timer and mod_timer instead
of structure assignments as they are standard way to set
the timer and to update the expire field of an active timer
respectively.
This is done using Coccinelle and semantic patch used for
this is as follows:
// <smpl>
@@
expression x,y,z,a,b;
@@
-init_timer (&x);
+setup_timer (&x, y, z);
+mod_timer (&a, b);
-x.function = y;
-x.data = z;
-x.expires = b;
-add_timer(&a);
// </smpl>
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change 'mutliple' to 'multiple'
Change 'Firmare' to 'Firmware'
Signed-off-by: Yannick Guerrini <yguerrini@tomshardware.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change 'Firmare' to 'Firmware'
Signed-off-by: Yannick Guerrini <yguerrini@tomshardware.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting a dev_pm_ops suspend/resume pair but not a set of
hibernation functions means those pm functions will not be
called upon hibernation.
Fix this by using SIMPLE_DEV_PM_OPS, which appropriately
assigns the suspend and hibernation handlers and move
cpsw_suspend/resume calbacks under CONFIG_PM_SLEEP
to avoid build warnings.
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting a dev_pm_ops suspend_late/resume_early pair but not a
set of hibernation functions means those pm functions will
not be called upon hibernation.
Fix this by using SET_LATE_SYSTEM_SLEEP_PM_OPS, which appropriately
assigns the suspend and hibernation handlers and move
davinci_mdio_x callbacks under CONFIG_PM_SLEEP to avoid build warnings.
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/urgent
Pull perf/urgent fixes from Arnaldo Carvalho de Melo:
- pthread_attr_setaffinity_np() feature detection build fixes (Adrian Hunter, Josh Boyer)
- Fix probing for PERF_FLAG_FD_CLOEXEC flag (Adrian Hunter)
- Fix order of arguments to memcpy_alloc_mem in 'perf bench' (Bruce Merry)
- Sparc64 and Aarch64 build and segfault fixes (David Ahern)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The "usual" path is:
- rt_mutex_slowlock()
- set_current_state()
- task_blocks_on_rt_mutex() (ret 0)
- __rt_mutex_slowlock()
- sleep or not but do return with __set_current_state(TASK_RUNNING)
- back to caller.
In the early error case where task_blocks_on_rt_mutex() return
-EDEADLK we never change the task's state back to RUNNING. I
assume this is intended. Without this change after ww_mutex
using rt_mutex the selftest passes but later I get plenty of:
| bad: scheduling from the idle thread!
backtraces.
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Mike Galbraith <umgwanakikbuti@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: afffc6c1805d ("locking/rtmutex: Optimize setting task running after being blocked")
Link: http://lkml.kernel.org/r/1425056229-22326-4-git-send-email-bigeasy@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
We did a failed attempt in the past to only use rcu in rtnl dump
operations (commit e67f88dd12f6 "net: dont hold rtnl mutex during
netlink dump callbacks")
Now that dumps are holding RTNL anyway, there is no need to also
use rcu locking, as it forbids any scheduling ability, like
GFP_KERNEL allocations that controlling path should use instead
of GFP_ATOMIC whenever possible.
This should fix following splat Cong Wang reported :
[ INFO: suspicious RCU usage. ]
3.19.0+ #805 Tainted: G W
include/linux/rcupdate.h:538 Illegal context switch in RCU read-side critical section!
other info that might help us debug this:
rcu_scheduler_active = 1, debug_locks = 0
2 locks held by ip/771:
#0: (rtnl_mutex){+.+.+.}, at: [<ffffffff8182b8f4>] netlink_dump+0x21/0x26c
#1: (rcu_read_lock){......}, at: [<ffffffff817d785b>] rcu_read_lock+0x0/0x6e
stack backtrace:
CPU: 3 PID: 771 Comm: ip Tainted: G W 3.19.0+ #805
Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
0000000000000001 ffff8800d51e7718 ffffffff81a27457 0000000029e729e6
ffff8800d6108000 ffff8800d51e7748 ffffffff810b539b ffffffff820013dd
00000000000001c8 0000000000000000 ffff8800d7448088 ffff8800d51e7758
Call Trace:
[<ffffffff81a27457>] dump_stack+0x4c/0x65
[<ffffffff810b539b>] lockdep_rcu_suspicious+0x107/0x110
[<ffffffff8109796f>] rcu_preempt_sleep_check+0x45/0x47
[<ffffffff8109e457>] ___might_sleep+0x1d/0x1cb
[<ffffffff8109e67d>] __might_sleep+0x78/0x80
[<ffffffff814b9b1f>] idr_alloc+0x45/0xd1
[<ffffffff810cb7ab>] ? rcu_read_lock_held+0x3b/0x3d
[<ffffffff814b9f9d>] ? idr_for_each+0x53/0x101
[<ffffffff817c1383>] alloc_netid+0x61/0x69
[<ffffffff817c14c3>] __peernet2id+0x79/0x8d
[<ffffffff817c1ab7>] peernet2id+0x13/0x1f
[<ffffffff817d8673>] rtnl_fill_ifinfo+0xa8d/0xc20
[<ffffffff810b17d9>] ? __lock_is_held+0x39/0x52
[<ffffffff817d894f>] rtnl_dump_ifinfo+0x149/0x213
[<ffffffff8182b9c2>] netlink_dump+0xef/0x26c
[<ffffffff8182bcba>] netlink_recvmsg+0x17b/0x2c5
[<ffffffff817b0adc>] __sock_recvmsg+0x4e/0x59
[<ffffffff817b1b40>] sock_recvmsg+0x3f/0x51
[<ffffffff817b1f9a>] ___sys_recvmsg+0xf6/0x1d9
[<ffffffff8115dc67>] ? handle_pte_fault+0x6e1/0xd3d
[<ffffffff8100a3a0>] ? native_sched_clock+0x35/0x37
[<ffffffff8109f45b>] ? sched_clock_local+0x12/0x72
[<ffffffff8109f6ac>] ? sched_clock_cpu+0x9e/0xb7
[<ffffffff810cb7ab>] ? rcu_read_lock_held+0x3b/0x3d
[<ffffffff811abde8>] ? __fcheck_files+0x4c/0x58
[<ffffffff811ac556>] ? __fget_light+0x2d/0x52
[<ffffffff817b376f>] __sys_recvmsg+0x42/0x60
[<ffffffff817b379f>] SyS_recvmsg+0x12/0x1c
Signed-off-by: Eric Dumazet <edumazet@google.com>
Fixes: 0c7aecd4bde4b7302 ("netns: add rtnl cmd to add and get peer netns ids")
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reported-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 740c7f31c094703c ("sh_eth: Ensure DMA engines are stopped before
freeing buffers") added a call to sh_eth_reset() to the
sh_eth_set_ringparam() and sh_eth_close() paths.
However, setting the software reset bit(s) in the EDMR register resets
the MAC Address Registers to zero. Hence after kexec, the new kernel
doesn't detect a valid MAC address and assigns a random MAC address,
breaking DHCP.
Set the MAC address again after the reset in sh_eth_dev_exit() to fix
this.
Tested on r8a7740/armadillo (GETHER) and r8a7791/koelsch (FAST_RCAR).
Fixes: 740c7f31c094703c ("sh_eth: Ensure DMA engines are stopped before freeing buffers")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds bcmgenet_tx_poll for the tx_rings. This can reduce the
interrupt load and send xmit in network stack on time. This also
separated for the completion of tx_ring16 from bcmgenet_poll.
The bcmgenet_tx_reclaim of tx_ring[{0,1,2,3}] operative by an interrupt
is to be not more than a certain number TxBDs. It is caused by too
slowly reclaiming the transmitted skb. Therefore, performance
degradation of xmit after 605ad7f ("tcp: refine TSO autosizing").
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Brian reported crashes using IPv6 traffic with macvtap/veth combo.
I tracked the crashes in neigh_hh_output()
-> memcpy(skb->data - HH_DATA_MOD, hh->hh_data, HH_DATA_MOD);
Neighbour code assumes headroom to push Ethernet header is
at least 16 bytes.
It appears macvtap has only 14 bytes available on arches
where NET_IP_ALIGN is 0 (like x86)
Effect is a corruption of 2 bytes right before skb->head,
and possible crashes if accessing non existing memory.
This fix should also increase IPv4 performance, as paranoid code
in ip_finish_output2() wont have to call skb_realloc_headroom()
Reported-by: Brian Rak <brak@vultr.com>
Tested-by: Brian Rak <brak@vultr.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
A few patches have accumulated, among them the fix for Linus's
four-way-handshake problem. The others are various small fixes
for problems all over, nothing really stands out.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When applicable verify that the caller has permisson to the underlying
network namespace for a newly created network device.
Similary checks exist for the network namespace a network device will
be created in.
Fixes: 317f4810e45e ("rtnl: allow to create device with IFLA_LINK_NETNSID set")
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When applicable verify that the caller has permision to create a
network device in another network namespace. This check is already
present when moving a network device between network namespaces in
setlink so all that is needed is to duplicate that check in newlink.
This change almost backports cleanly, but there are context conflicts
as the code that follows was added in v4.0-rc1
Fixes: b51642f6d77b net: Enable a userns root rtnl calls that are safe for unprivilged users
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prior to this patch, sending a packet with the source MAC address of one
of the CPSW interfaces to one of the CPSW slave ports while it's configured in
dual_emac mode would update the port_num field of the VLAN/Unicast Address
Table Entry. This would cause it to discard all incoming traffic addressed to
that MAC address, essentially rendering the port useless until the ALE table is
cleared (by starting and stopping the interface or rebooting.)
For example, if eth0 has a MAC address of 90:59:af:8f:43:e9 it will have
an ALE table entry:
00 00 00 00 59 90 02 30 e9 43 8f af
(VLAN Addr vlan_id=2 unicast type=0 port_num=0 addr=90:59:af:8f:43:e9)
If you configure another device with the same MAC address and connect it
to the first CPSW slave port and send some traffic the ALE table entry
becomes:
04 00 00 00 59 90 02 30 e9 43 8f af
(VLAN Addr vlan_id=2 unicast type=0 port_num=1 addr=90:59:af:8f:43:e9)
>From this point forward all incoming traffic addressed to
90:59:af:8f:43:e9 will be dropped.
Setting the SECURE bit for the VLAN/Unicast address table entry for each
interface's MAC address corrects the problem.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull drm fixes from Dave Airlie:
"Just general fixes: radeon, i915, atmel, tegra, amdkfd and one core
fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (28 commits)
drm: atmel-hlcdc: remove clock polarity from crtc driver
drm/radeon: only enable DP audio if the monitor supports it
drm/radeon: fix atom aux payload size check for writes (v2)
drm/radeon: fix 1 RB harvest config setup for TN/RL
drm/radeon: enable SRBM timeout interrupt on EG/NI
drm/radeon: enable SRBM timeout interrupt on SI
drm/radeon: enable SRBM timeout interrupt on CIK v2
drm/radeon: dump full IB if we hit a packet error
drm/radeon: disable mclk switching with 120hz+ monitors
drm/radeon: use drm_mode_vrefresh() rather than mode->vrefresh
drm/radeon: enable native backlight control on old macs
drm/i915: Fix frontbuffer false positve.
drm/i915: Align initial plane backing objects correctly
drm/i915: avoid processing spurious/shared interrupts in low-power states
drm/i915: Check obj->vma_list under the struct_mutex
drm/i915: Fix a use after free, and unbalanced refcounting
drm: atmel-hlcdc: remove useless pm_runtime_put_sync in probe
drm: atmel-hlcdc: reset layer A2Q and UPDATE bits when disabling it
drm: Fix deadlock due to getconnector locking changes
drm/i915: Dell Chromebook 11 has PWM backlight
...
|
|
Pull block layer fixes from Jens Axboe:
"Two smaller fixes for this cycle:
- A fixup from Keith so that NVMe compiles without BLK_INTEGRITY,
basically just moving the code around appropriately.
- A fixup for shm, fixing an oops in shmem_mapping() for mapping with
no inode. From Sasha"
[ The shmem fix doesn't look block-layer-related, but fixes a bug that
happened due to the backing_dev_info removal.. - Linus ]
* 'for-linus' of git://git.kernel.dk/linux-block:
mm: shmem: check for mapping owner before dereferencing
NVMe: Fix for BLK_DEV_INTEGRITY not set
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"These are fixes for regressions/bugs introduced in the 4.0 merge cycle
and problems discovered during the merge window that need to be pushed
back to stable kernels ASAP.
This contains:
- ensure quota type is reset in on-disk dquots
- fix missing partial EOF block data flush on truncate extension
- fix transaction leak in error handling for new pnfs block layout
support
- add missing target_ip check to RENAME_EXCHANGE"
* tag 'xfs-for-linus-4.0-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: cancel failed transaction in xfs_fs_commit_blocks()
xfs: Ensure we have target_ip for RENAME_EXCHANGE
xfs: ensure truncate forces zeroed blocks to disk
xfs: Fix quota type in quota structures when reusing quota file
|
|
There is a discrepancy here because the niu_class_to_ethflow() returns
zero on failure and one on success but the caller expected zero on
success and negative on failure.
The problem means that we allow the user to pass classes and flow_types
which we don't want. I've looked at it a bit and I don't see it as a
very serious bug.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge misc fixes from Andrew Morton:
"13 fixes"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
mm: add missing __PAGETABLE_{PUD,PMD}_FOLDED defines
mm: page_alloc: revert inadvertent !__GFP_FS retry behavior change
kernel/sys.c: fix UNAME26 for 4.0
mm: memcontrol: use "max" instead of "infinity" in control knobs
zram: use proper type to update max_used_pages
drivers/rtc/rtc-ds1685.c: fix conditional in ds1685_rtc_sysfs_time_regs_{show,store}
nilfs2: fix potential memory overrun on inode
scripts/gdb: add empty package initialization script
rtc: ds1685: remove superfluous checks for out-of-range u8 values
rtc: ds1685: fix ds1685_rtc_alarm_irq_enable build error
memcg: fix low limit calculation
mm/nommu: fix memory leak
ocfs2: update web page + git tree in documentation
|
|
Core mm expects __PAGETABLE_{PUD,PMD}_FOLDED to be defined if these page
table levels folded. Usually, these defines are provided by
<asm-generic/pgtable-nopmd.h> and <asm-generic/pgtable-nopud.h>.
But some architectures fold page table levels in a custom way. They
need to define these macros themself. This patch adds missing defines.
The patch fixes mm->nr_pmds underflow and eliminates dead __pmd_alloc()
and __pud_alloc() on architectures without these page table levels.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
Cc: David Howells <dhowells@redhat.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Helge Deller <deller@gmx.de>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Koichi Yasutake <yasutake.koichi@jp.panasonic.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Historically, !__GFP_FS allocations were not allowed to invoke the OOM
killer once reclaim had failed, but nevertheless kept looping in the
allocator.
Commit 9879de7373fc ("mm: page_alloc: embed OOM killing naturally into
allocation slowpath"), which should have been a simple cleanup patch,
accidentally changed the behavior to aborting the allocation at that
point. This creates problems with filesystem callers (?) that currently
rely on the allocator waiting for other tasks to intervene.
Revert the behavior as it shouldn't have been changed as part of a
cleanup patch.
Fixes: 9879de7373fc ("mm: page_alloc: embed OOM killing naturally into allocation slowpath")
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Acked-by: Michal Hocko <mhocko@suse.cz>
Reported-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: Theodore Ts'o <tytso@mit.edu>
Cc: Dave Chinner <david@fromorbit.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: <stable@vger.kernel.org> [3.19.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
