| Age | Commit message (Collapse) | Author |
|---|
|
Currently the usbnet core does not update the tx_packets statistic for
drivers with FLAG_MULTI_PACKET and there is no hook in the TX
completion path where they could do this.
cdc_ncm and dependent drivers are bumping tx_packets stat on the
transmit path while asix and sr9800 aren't updating it at all.
Add a packet count in struct skb_data so these drivers can fill it
in, initialise it to 1 for other drivers, and add the packet count
to the tx_packets statistic on completion.
Signed-off-by: Ben Hutchings <ben.hutchings@codethink.co.uk>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To reduce the number of interrupts/message we fill the FIFO before
enabling interrupts - for short messages this reduces the interrupt count
from 2 to 1 interrupt.
There have been rare cases where short (<200ns) chip-select switches with
native CS have been observed during such operation, this is why this
optimization is only enabled for GPIO-CS.
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Tested-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Martin Sperl <kernel@martin.sperl.org>
Tested-by: Martin Sperl <kernel@martin.sperl.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The model is detected by reading the EEPROM configuration during
probing.
Signed-off-by: Vianney le Clément de Saint-Marcq <vianney.leclement@essensium.com>
Cc: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Add symbols for all accessible RAM and EEPROM registers, as well as the
sleep command and timings defined in the datasheet.
Signed-off-by: Vianney le Clément de Saint-Marcq <vianney.leclement@essensium.com>
Cc: Arnout Vandecappelle (Essensium/Mind) <arnout@mind.be>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
We only advertise hardware fifo support if the I2C bus supports full
I2C or smbus I2C block data reads since it is mandatory to read the
full frame in one read (otherwise the rest of the frame is discarded).
The hardware fifo is enabled only when triggers are not active because:
(a) when using the any-motion trigger the user expects to see samples
based on ROC events, but the fifo stores samples based on the sample
frequency
(b) the data-ready trigger is waking the CPU for for every sample, so
using the hardware fifo does not have any benefit
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Some devices have hardware buffers that can store a number of samples
for later consumption. Hardware usually provides interrupts to notify
the processor when the FIFO is full or when it has reached a certain
watermark level. This helps with reducing the number of interrupts to
the host processor and thus it helps decreasing the power consumption.
This patch enables usage of hardware FIFOs for IIO devices in
conjunction with software device buffers. When the hardware FIFO is
enabled the samples are stored in the hardware FIFO. The samples are
later flushed to the device software buffer when the number of entries
in the hardware FIFO reaches the hardware watermark or when a flush
operation is triggered by the user when doing a non-blocking read
on an empty software device buffer.
In order to implement hardware FIFO support the device drivers must
implement the following new operations: setting and getting the
hardware FIFO watermark level, flushing the hardware FIFO to the
software device buffer. The device must also expose information about
the hardware FIFO such it's minimum and maximum watermark and if
necessary a list of supported watermark values. Finally, the device
driver must activate the hardware FIFO when the device buffer is
enabled, if the current device settings allows it.
The software device buffer watermark is passed by the IIO core to the
device driver as a hint for the hardware FIFO watermark. The device
driver can adjust this value to allow for hardware limitations (such
as capping it to the maximum hardware watermark or adjust it to a
value that is supported by the hardware). It can also disable the
hardware watermark (and implicitly the hardware FIFO) it this value is
below the minimum hardware watermark.
Since a driver may support hardware FIFO only when not in triggered
buffer mode (due to different semantics of hardware FIFO sampling and
triggered sampling) this patch changes the IIO core code to allow
falling back to non-triggered buffered mode if no trigger is enabled.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Currently the IIO buffer blocking read only wait until at least one
data element is available.
This patch makes the reader sleep until enough data is collected before
returning to userspace. This should limit the read() calls count when
trying to get data in batches.
Co-author: Yannick Bedhomme <yannick.bedhomme@mobile-devices.fr>
Signed-off-by: Josselin Costanzi <josselin.costanzi@mobile-devices.fr>
[rebased and remove buffer timeout]
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Ingo Molnar:
"Fix x86 syscall exit code bug that resulted in spurious non-execution
of TIF-driven user-return worklets, causing big trouble for things
like KVM that rely on user notifiers for correctness of their vcpu
model, causing crashes like double faults"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/asm/entry: Check for syscall exit work with IRQs disabled
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Ingo Molnar:
"Two clocksource driver fixes, and an idle loop RCU warning fix"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource/drivers/sun5i: Fix cpufreq interaction with sched_clock()
clocksource/drivers: Fix various !CONFIG_HAS_IOMEM build errors
timers/tick/broadcast-hrtimer: Fix suspicious RCU usage in idle loop
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Ingo Molnar:
"A single sched/rt corner case fix for RLIMIT_RTIME correctness"
* 'sched-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched: Fix RLIMIT_RTTIME when PI-boosting to RT
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fix from Ingo Molnar:
"A perf kernel side fix for a fuzzer triggered lockup"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf: Fix irq_work 'tail' recursion
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull locking fix from Ingo Molnar:
"A module unload lockdep race fix"
* 'locking-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
lockdep: Fix the module unload key range freeing logic
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux
Pull parsic fixes from Helge Deller:
"One patch from Mikulas fixes a bug on parisc by artifically
incrementing the counter in pmd_free when the kernel tries to free
the preallocated pmd.
Other than that we now prevent that syscalls gets added without
incrementing __NR_Linux_syscalls and fix the initial pmd setup code
if a default page size greater than 4k has been selected"
* 'parisc-4.0-1' of git://git.kernel.org/pub/scm/linux/kernel/git/deller/parisc-linux:
parisc: Fix pmd code to depend on PT_NLEVELS value, not on CONFIG_64BIT
parisc: mm: don't count preallocated pmds
parisc: Add compile-time check when adding new syscalls
|
|
Pull kvm ppc bugfixes from Marcelo Tosatti.
* git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: PPC: Book3S HV: Fix instruction emulation
KVM: PPC: Book3S HV: Endian fix for accessing VPA yield count
KVM: PPC: Book3S HV: Fix spinlock/mutex ordering issue in kvmppc_set_lpcr()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc
Pull ARC fixes from Vineet Gupta:
"We found some issues with signal handling taking down the system. I
know its late, but these are important and all marked for stable.
ARC signal handling related fixes uncovered during recent testing of
NPTL tools"
* tag 'arc-4.0-fixes-part-2' of git://git.kernel.org/pub/scm/linux/kernel/git/vgupta/arc:
ARC: signal handling robustify
ARC: SA_SIGINFO ucontext regs off-by-one
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull selinux bugfix from James Morris.
Fix broken return value.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
selinux: fix sel_write_enforce broken return value
|
|
This patch uses iio_trigger_get to increment the reference
count of trigger device, to avoid incorrect assignment.
Can result in a null pointer dereference during removal if the
trigger has been changed before removal.
This patch refers to a similar situation encountered through the
following discussion:
http://www.spinics.net/lists/linux-iio/msg13669.html
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Depending on conversion mode used, the ADC clock (ADCK) needs
to be below a maximum frequency. According to Vybrid's data
sheet this is 20MHz for the low power conversion mode.
The ADC clock is depending on input clock, which is the bus
clock by default. Vybrid SoC are typically clocked at at 400MHz
or 500MHz, which leads to 66MHz or 83MHz bus clock respectively.
Hence, a divider of 8 is required to stay below the specified
maximum clock of 20MHz.
Due to the different bus clock speeds, the resulting sampling
frequency is not static. Hence use the ADC clock and calculate
the actual available sampling frequency dynamically.
This fixes bogous values observed on some 500MHz clocked Vybrid
SoC. The resulting value usually showed Bit 9 being stuck at 1,
or 0, which lead to a value of +/-512.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Fugang Duan <B38611@freescale.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
Fixes:
drivers/built-in.o: In function `cc10001_adc_probe':
cc10001_adc.c:(.text+0x412e92): undefined reference to `devm_ioremap_resource'
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
It can be used exactly like L3GD20 but it has a different WhoAmI
register value.
Signed-off-by: Robert Dolca <robert.dolca@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
When using generic_buffer to read data, the scale is not properly
detected for scale shared by type. This is caused by a problem
with the generation of generic name out of the full name.
E.g.: for current->name in_accel_z, the extracted generic name
is "in" (when it should be "in_accel"). This is used in generic_buffer
to generate scale and offset paths (in_accel_scale).
Consider the in_ or out_ prefix when extracting the generic name
from the full name.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Reviewed-by: Daniel Baluta <daniel.baluta@intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch adds ABI documentation entries for in_rot_offset.
At least one user for these is present that is the HID Sensors Driver.
Signed-off-by: Haneen Mohammed <hamohammed.sa@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
MAX520 and MAX521 are protocol-compatible with the already supported
chips, just have more channels.
Signed-off-by: Antonio Fiol <antonio@fiol.es>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
of_device_id is always used as const.
(See driver.of_match_table and open firmware functions)
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patchset adds ABI documentation for the following attributes:
in_illuminance_scale, used atleast once in al3320a staging/iio/light/
in_illuminance_calibscale, used atleast once in cm32181
in_illuminance_input, used in cm3232 at least once
in_illuminance_raw used atleast once in al3320a
in_illuminance_clear_raw and in_illuminance_ir_raw exposed by
gp2ap020a00f with modifiers IIO_MOD_LIGHT_CLEAR and
IIO_MOD_LIGHT_IR respectively.
Signed-off-by: Darshana Padmadas <darshanapadmadas@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This adds support for the LIS3LV02 accelerometer found in the
ST Microelectronics Nomadik board series.
Cc: devicetree@vger.kernel.org
Cc: Denis CIOCCA <denis.ciocca@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
The "sdc" node is missing the ranges property, it needs to be treated
as having an empty one otherwise translation fails for its children.
Fixes 746c9e9f92dd, "of/base: Fix PowerPC address parsing hack"
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Stable <stable@vger.kernel.org> # v3.18+
|
|
Since spidev is a detail of how Linux controls a device rather than a
description of the hardware in the system we should never have a node
described as "spidev" in DT, any SPI device could be a spidev so this
is just not a useful description.
In order to help prevent users from writing such device trees generate a
warning if spidev is instantiated as a DT node without an ID in the match
table.
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
If multiple regulator devices of the same type exist in a system,
the regulator driver assigns generic names for the regulators it
provides, and debugfs is enabled, the regulator subsystem attempts
to create multiple entries with the same name in the regulator debugfs
directory. This fails for all but the first regulator, resulting in
multiple "Failed to create debugfs directory" log entries.
To avoid the problem, prepend the debugfs directory name for a regulator
with its parent device name if available, but only if no explicit
regulator name was provided.
Cc: Alan Tull <atull@opensource.altera.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Pull watchdog fixes from Wim Van Sebroeck:
- mtk_wdt: signedness bug in mtk_wdt_start()
- imgpdc: Fix NULL pointer dereference during probe and fix the default
heartbeat
* git://www.linux-watchdog.org/linux-watchdog:
watchdog: imgpdc: Fix default heartbeat
watchdog: imgpdc: Fix probe NULL pointer dereference
watchdog: mtk_wdt: signedness bug in mtk_wdt_start()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"Three trivial oneliner fixes for HD-audio.
Two are device-specific quirks while one is a generic fix for recent
Realtek codecs"
* tag 'sound-4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Add one more node in the EAPD supporting candidate list
ALSA: hda_intel: apply the Seperate stream_tag for Sunrise Point
ALSA: hda - Add dock support for Thinkpad T450s (17aa:5036)
|
|
Now that the code is in place for KVM to support MIPS SIMD Architecutre
(MSA) in MIPS guests, wire up the new KVM_CAP_MIPS_MSA capability.
For backwards compatibility, the capability must be explicitly enabled
in order to detect or make use of MSA from the guest.
The capability is not supported if the hardware supports MSA vector
partitioning, since the extra support cannot be tested yet and it
extends the state that the userland program would have to save.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-api@vger.kernel.org
Cc: linux-doc@vger.kernel.org
|
|
Add KVM register numbers for the MIPS SIMD Architecture (MSA) registers,
and implement access to them with the KVM_GET_ONE_REG / KVM_SET_ONE_REG
ioctls when the MSA capability is enabled (exposed in a later patch) and
present in the guest according to its Config3.MSAP bit.
The MSA vector registers use the same register numbers as the FPU
registers except with a different size (128bits). Since MSA depends on
Status.FR=1, these registers are inaccessible when Status.FR=0. These
registers are returned as a single native endian 128bit value, rather
than least significant half first with each 64-bit half native endian as
the kernel uses internally.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-api@vger.kernel.org
Cc: linux-doc@vger.kernel.org
|
|
Add guest exception handling for MIPS SIMD Architecture (MSA) floating
point exceptions and MSA disabled exceptions.
MSA floating point exceptions from the guest need passing to the guest
kernel, so for these a guest MSAFPE is emulated.
MSA disabled exceptions are normally handled by passing a reserved
instruction exception to the guest (because no guest MSA was supported),
but the hypervisor can now handle them if the guest has MSA by passing
an MSA disabled exception to the guest, or if the guest has MSA enabled
by transparently restoring the guest MSA context and enabling MSA and
the FPU.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
Emulate MSA related parts of COP0 interface so that the guest will be
able to enable/disable MSA (Config5.MSAEn) once the MSA capability has
been wired up.
As with the FPU (Status.CU1) setting Config5.MSAEn has no immediate
effect if the MSA state isn't live, as MSA state is restored lazily on
first use. Changes after the MSA state has been restored take immediate
effect, so that the guest can start getting MSA disabled exceptions
right away for guest MSA operations. The MSA state is saved lazily too,
as MSA may get re-enabled in the near future anyway.
A special case is also added for when Status.CU1 is set while FR=0 and
the MSA state is live. In this case we are at risk of getting reserved
instruction exceptions if we try and save the MSA state, so we lose the
MSA state sooner while MSA is still usable.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
Add base code for supporting the MIPS SIMD Architecture (MSA) in MIPS
KVM guests. MSA cannot yet be enabled in the guest, we're just laying
the groundwork.
As with the FPU, whether the guest's MSA context is loaded is stored in
another bit in the fpu_inuse vcpu member. This allows MSA to be disabled
when the guest disables it, but keeping the MSA context loaded so it
doesn't have to be reloaded if the guest re-enables it.
New assembly code is added for saving and restoring the MSA context,
restoring only the upper half of the MSA context (for if the FPU context
is already loaded) and for saving/clearing and restoring MSACSR (which
can itself cause an MSA FP exception depending on the value). The MSACSR
is restored before returning to the guest if MSA is already enabled, and
the existing FP exception die notifier is extended to catch the possible
MSA FP exception and step over the ctcmsa instruction.
The helper function kvm_own_msa() is added to enable MSA and restore
the MSA context if it isn't already loaded, which will be used in a
later patch when the guest attempts to use MSA for the first time and
triggers an MSA disabled exception.
The existing FPU helpers are extended to handle MSA. kvm_lose_fpu()
saves the full MSA context if it is loaded (which includes the FPU
context) and both kvm_lose_fpu() and kvm_drop_fpu() disable MSA.
kvm_own_fpu() also needs to lose any MSA context if FR=0, since there
would be a risk of getting reserved instruction exceptions if CU1 is
enabled and we later try and save the MSA context. We shouldn't usually
hit this case since it will be handled when emulating CU1 changes,
however there's nothing to stop the guest modifying the Status register
directly via the comm page, which will cause this case to get hit.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
Now that the code is in place for KVM to support FPU in MIPS KVM guests,
wire up the new KVM_CAP_MIPS_FPU capability.
For backwards compatibility, the capability must be explicitly enabled
in order to detect or make use of the FPU from the guest.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-api@vger.kernel.org
Cc: linux-doc@vger.kernel.org
|
|
Add KVM register numbers for the MIPS FPU registers, and implement
access to them with the KVM_GET_ONE_REG / KVM_SET_ONE_REG ioctls when
the FPU capability is enabled (exposed in a later patch) and present in
the guest according to its Config1.FP bit.
The registers are accessible in the current mode of the guest, with each
sized access showing what the guest would see with an equivalent access,
and like the architecture they may become UNPREDICTABLE if the FR mode
is changed. When FR=0, odd doubles are inaccessible as they do not exist
in that mode.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: Jonathan Corbet <corbet@lwn.net>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
Cc: linux-api@vger.kernel.org
Cc: linux-doc@vger.kernel.org
|
|
Add guest exception handling for floating point exceptions and
coprocessor 1 unusable exceptions.
Floating point exceptions from the guest need passing to the guest
kernel, so for these a guest FPE is emulated.
Also, coprocessor 1 unusable exceptions are normally passed straight
through to the guest (because no guest FPU was supported), but the
hypervisor can now handle them if the guest has its FPU enabled by
restoring the guest FPU context and enabling the FPU.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
Emulate FPU related parts of COP0 interface so that the guest will be
able to enable/disable the following once the FPU capability has been
wired up:
- The FPU (Status.CU1)
- 64-bit FP register mode (Status.FR)
- Hybrid FP register mode (Config5.FRE)
Changing Status.CU1 has no immediate effect if the FPU state isn't live,
as the FPU state is restored lazily on first use. After that, changes
take place immediately in the host Status.CU1, so that the guest can
start getting coprocessor unusable exceptions right away for guest FPU
operations if it is disabled. The FPU state is saved lazily too, as the
FPU may get re-enabled in the near future anyway.
Any change to Status.FR causes the FPU state to be discarded and FPU
disabled, as the register state is architecturally UNPREDICTABLE after
such a change. This should also ensure that the FPU state is fully
initialised (with stale state, but that's fine) when it is next used in
the new FP mode.
Any change to the Config5.FRE bit is immediately updated in the host
state so that the guest can get the relevant exceptions right away for
single-precision FPU operations.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
Add base code for supporting FPU in MIPS KVM guests. The FPU cannot yet
be enabled in the guest, we're just laying the groundwork.
Whether the guest's FPU context is loaded is stored in a bit in the
fpu_inuse vcpu member. This allows the FPU to be disabled when the guest
disables it, but keeping the FPU context loaded so it doesn't have to be
reloaded if the guest re-enables it.
An fpu_enabled vcpu member stores whether userland has enabled the FPU
capability (which will be wired up in a later patch).
New assembly code is added for saving and restoring the FPU context, and
for saving/clearing and restoring FCSR (which can itself cause an FP
exception depending on the value). The FCSR is restored before returning
to the guest if the FPU is already enabled, and a die notifier is
registered to catch the possible FP exception and step over the ctc1
instruction.
The helper function kvm_lose_fpu() is added to save FPU context and
disable the FPU, which is used when saving hardware state before a
context switch or KVM exit (the vcpu_get_regs() callback).
The helper function kvm_own_fpu() is added to enable the FPU and restore
the FPU context if it isn't already loaded, which will be used in a
later patch when the guest attempts to use the FPU for the first time
and triggers a co-processor unusable exception.
The helper function kvm_drop_fpu() is added to discard the FPU context
and disable the FPU, which will be used in a later patch when the FPU
state will become architecturally UNPREDICTABLE (change of FR mode) to
force a reload of [stale] context in the new FR mode.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
Add a vcpu_get_regs() and vcpu_set_regs() callbacks for loading and
restoring context which may be in hardware registers. This may include
floating point and MIPS SIMD Architecture (MSA) state which may be
accessed directly by the guest (but restored lazily by the hypervisor),
and also dedicated guest registers as provided by the VZ ASE.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
Add Config4 and Config5 co-processor 0 registers, and add capability to
write the Config1, Config3, Config4, and Config5 registers using the KVM
API.
Only supported bits can be written, to minimise the chances of the guest
being given a configuration from e.g. QEMU that is inconsistent with
that being emulated, and as such the handling is in trap_emul.c as it
may need to be different for VZ. Currently the only modification
permitted is to make Config4 and Config5 exist via the M bits, but other
bits will be added for FPU and MSA support in future patches.
Care should be taken by userland not to change bits without fully
handling the possible extra state that may then exist and which the
guest may begin to use and depend on.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
Various semi-used definitions exist in kvm_host.h for the default guest
config registers. Remove them and use the appropriate values directly
when initialising the Config registers.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
Clean up KVM_GET_ONE_REG / KVM_SET_ONE_REG register definitions for
MIPS, to prepare for adding a new group for FPU & MSA vector registers.
Definitions are added for common bits in each group of registers, e.g.
KVM_REG_MIPS_CP0 = KVM_REG_MIPS | 0x10000, for the coprocessor 0
registers.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
The information messages when the KVM module is loaded and unloaded are
a bit pointless and out of line with other architectures, so lets drop
them.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
Sort the registers in the kvm_mips_get_reg() switch by register number,
which puts ERROREPC after the CONFIG registers.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
|
Implement access to the guest Processor Identification CP0 register
using the KVM_GET_ONE_REG and KVM_SET_ONE_REG ioctls. This allows the
owning process to modify and read back the value that is exposed to the
guest in this register.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Gleb Natapov <gleb@kernel.org>
Cc: linux-mips@linux-mips.org
Cc: kvm@vger.kernel.org
|
