| Age | Commit message (Collapse) | Author |
|---|
|
The usb_request->zero doesn't apply for isoc. Also, if we prepare a
0-length (ZLP) TRB for the OUT direction, we need to prepare an extra
TRB to pad up to the MPS alignment. Use the same bounce buffer for the
ZLP TRB and the extra pad TRB.
Cc: <stable@vger.kernel.org> # v4.5+
Fixes: d6e5a549cc4d ("usb: dwc3: simplify ZLP handling")
Fixes: 04c03d10e507 ("usb: dwc3: gadget: handle request->zero")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
The SG list may be set up with entry size more than the requested
length. Check the usb_request->length and make sure that we don't setup
the TRBs to send/receive more than requested. This case may occur when
the SG entry is allocated up to a certain minimum size, but the request
length is less than that. It can also occur when the request is reused
for a different request length.
Cc: <stable@vger.kernel.org> # v4.18+
Fixes: a31e63b608ff ("usb: dwc3: gadget: Correct handling of scattergather lists")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
When power_up_sst() fails, stream needs to be freed
just like when try_module_get() fails. However, current
code is returning directly and ends up leaking memory.
Fixes: 0121327c1a68b ("ASoC: Intel: mfld-pcm: add control for powering up/down dsp")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Acked-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200813084112.26205-1-dinghao.liu@zju.edu.cn
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The driver supports WM1811, WM8994, WM8958 devices but according to
documentation and the regmap definitions the WM8958_DSP2_* registers
are only available on WM8958. In current code these registers are
being accessed as if they were available on all the three chips.
When starting playback on WM1811 CODEC multiple errors like:
"wm8994-codec wm8994-codec: ASoC: error at soc_component_read_no_lock on wm8994-codec: -5"
can be seen, which is caused by attempts to read an unavailable
WM8958_DSP2_PROGRAM register. The issue has been uncovered by recent
commit "e2329ee ASoC: soc-component: add soc_component_err()".
This patch adds a check in wm8958_aif_ev() callback so the DSP2 handling
is only done for WM8958.
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Acked-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20200731173834.23832-1-s.nawrocki@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
For some reason interrupt set and clear register offsets are
not set correctly.
This patch corrects them!
Fixes: 585e881e5b9e ("ASoC: codecs: Add msm8916-wcd analog codec")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Tested-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20200811103452.20448-1-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The ADC2 and DAC2 are not available on WM1811 device. This patch moves
the ADC2, DAC2 VU bitfields to a separate array so we can skip accessing
them and avoid unreadable register access on WM1811.
This allows to get rid of warnings during boot like:
wm8994-codec: ASoC: error at soc_component_read_no_lock on wm8994-codec: -5
Signed-off-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Link: https://lore.kernel.org/r/20200804141043.11425-1-s.nawrocki@samsung.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Currently there are four places in which a PCI function is scanned
and made available to drivers:
1. In pci_scan_root_bus() as part of the initial zbus
creation.
2. In zpci_bus_add_devices() when registering
a device in configured state on a zbus that has already been
scanned.
3. When a function is already known to zPCI (in reserved/standby state)
and configuration is triggered through firmware by PEC 0x301.
4. When a device is already known to zPCI (in standby/reserved state)
and configuration is triggered from within Linux using
enable_slot().
The PF/VF linking step and setting of pdev->is_virtfn introduced with
commit e5794cf1a270 ("s390/pci: create links between PFs and VFs") was
only triggered for the second case, which is where VFs created through
sriov_numvfs usually land. However unlike some other platforms but like
POWER VFs can be individually enabled/disabled through
/sys/bus/pci/slots.
Fix this by doing VF setup as part of pcibios_bus_add_device() which is
called in all of the above cases.
Finally to remove the PF/VF links call the common code
pci_iov_remove_virtfn() function to remove linked VFs.
This takes care of the necessary sysfs cleanup.
Fixes: e5794cf1a270 ("s390/pci: create links between PFs and VFs")
Cc: <stable@vger.kernel.org> # 5.8: 2f0230b2f2d5: s390/pci: re-introduce zpci_remove_device()
Cc: <stable@vger.kernel.org> # 5.8
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
For fixing the PF to VF link removal we need to perform some action on
every removal of a zdev from the common PCI subsystem.
So in preparation re-introduce zpci_remove_device() and use that instead
of directly calling the common code functions. This was actually still
declared from earlier code but no longer implemented.
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
We were missing the pci_dev_put() for candidate PFs. Furhtermore in
discussion with upstream it turns out that somewhat counterintuitively
some common code, in particular the vfio-pci driver, assumes that
pdev->is_virtfn always implies that pdev->physfn is set, i.e. that VFs
are always linked.
While POWER does seem to set pdev->is_virtfn even for unlinked functions
(see comments in arch/powerpc/kernel/eeh.c:eeh_debugfs_break_device())
for now just be safe and only set pdev->is_virtfn on linking.
Also make sure that we only search for parent PFs if the zbus is
multifunction and we thus know the devfn values supplied by firmware
come from the RID.
Fixes: e5794cf1a270 ("s390/pci: create links between PFs and VFs")
Cc: <stable@vger.kernel.org> # 5.8
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The key member of the runtime instrumentation control block contains
only the access key, not the complete storage key. Therefore the value
must be shifted by four bits. Since existing user space does not
necessarily query and set the access key correctly, just ignore the
user space provided key and use the correct one.
Note: this is only relevant for debugging purposes in case somebody
compiles a kernel with a default storage access key set to a value not
equal to zero.
Fixes: 262832bc5acd ("s390/ptrace: add runtime instrumention register get/set")
Reported-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The key member of the runtime instrumentation control block contains
only the access key, not the complete storage key. Therefore the value
must be shifted by four bits.
Note: this is only relevant for debugging purposes in case somebody
compiles a kernel with a default storage access key set to a value not
equal to zero.
Fixes: e4b8b3f33fca ("s390: add support for runtime instrumentation")
Reported-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
A configuration request event may be stale, that is the event
may reference a zdev which was already configured.
This can happen when a hotplug happens during boot such that
the device is discovered and configured in the initial clp_list_pci(),
then after initialization we enable events and process
the original configuration request which additionally still contains
the old disabled function handle leading to a failure during device
enablement and subsequent I/O lockout.
Fix this by restoring the check that the device to be configured is in
standby which was removed in commit f606b3ef47c9 ("s390/pci: adapt events
for zbus").
This check does not need serialization as we only enable the events after
zPCI has fully initialized, which includes the initial clp_list_pci(),
rescan only does updates and events are serialized with respect to each
other.
Fixes: f606b3ef47c9 ("s390/pci: adapt events for zbus")
Cc: <stable@vger.kernel.org> # 5.8
Reported-by: Shalini Chellathurai Saroja <shalini@linux.ibm.com>
Tested-by: Shalini Chellathurai Saroja <shalini@linux.ibm.com>
Acked-by: Pierre Morel <pmorel@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The scanning through subchannels during the time of an event could
take significant amount of time in case of platforms with lots of
known subchannels. This might result in higher scheduling latencies
for other tasks especially on systems with a single CPU. Add
cond_resched() call, as the loop in slow_eval_known_fn() can be
executed for a longer duration.
Reviewed-by: Peter Oberparleiter <oberpar@linux.ibm.com>
Signed-off-by: Vineeth Vijayan <vneethv@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Do not override ejtag feature to 0 as Loongson 3A1000+ do have ejtag.
For watch, as KVM emulated CPU doesn't have watch feature, we should
not enable it unconditionally.
Signed-off-by: Jiaxun Yang <jiaxun.yang@flygoat.com>
Reviewed-by: Huacai Chen <chenhc@lemote.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
If a memory allocation fails within a 'usb_ep_alloc_request()' call, the
already allocated memory must be released.
Fix a mix-up in the code and free the correct requests.
Fixes: c52661d60f63 ("usb-gadget: Initial merge of target module for UASP + BOT")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
|
|
`uref->usage_index` is not always being properly checked, causing
hiddev_ioctl_usage() to go out of bounds under some cases. Fix it.
Reported-by: syzbot+34ee1b45d88571c2fa8b@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=f2aebe90b8c56806b050a20b36f51ed6acabe802
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Peilin Ye <yepeilin.cs@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The PixArt OEM mice are known for disconnecting every minute in
runlevel 1 or 3 if they are not always polled. One Lenovo PixArt
mouse is already fixed. Got two references for 17ef:602e and three
references for 17ef:6019 misbehaving like this. Got one direct bug
report for 17ef:6093 from Wyatt Ward (wyatt8740). So add
HID_QUIRK_ALWAYS_POLL for all of them.
Link: https://github.com/sriemer/fix-linux-mouse issue 22
Signed-off-by: Sebastian Parschauer <s.parschauer@gmx.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Before this commit i2c_hid_parse() consists of the following steps:
1. Send power on cmd
2. usleep_range(1000, 5000)
3. Send reset cmd
4. Wait for reset to complete (device interrupt, or msleep(100))
5. Send power on cmd
6. Try to read HID descriptor
Notice how there is an usleep_range(1000, 5000) after the first power-on
command, but not after the second power-on command.
Testing has shown that at least on the BMAX Y13 laptop's i2c-hid touchpad,
not having a delay after the second power-on command causes the HID
descriptor to read as all zeros.
In case we hit this on other devices too, the descriptor being all zeros
can be recognized by the following message being logged many, many times:
hid-generic 0018:0911:5288.0002: unknown main item tag 0x0
At the same time as the BMAX Y13's touchpad issue was debugged,
Kai-Heng was working on debugging some issues with Goodix i2c-hid
touchpads. It turns out that these need a delay after a PWR_ON command
too, otherwise they stop working after a suspend/resume cycle.
According to Goodix a delay of minimal 60ms is needed.
Having multiple cases where we need a delay after sending the power-on
command, seems to indicate that we should always sleep after the power-on
command.
This commit fixes the mentioned issues by moving the existing 1ms sleep to
the i2c_hid_set_power() function and changing it to a 60ms sleep.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=208247
Reported-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reported-and-tested-by: Andrea Borgia <andrea@borgia.bo.it>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
macally_id_table is not modified and can be made const to allow the
compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
cougar_id_table[] is not changed and can be made const to allow the
compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
The very quiet and distorted headphone output bug that afflicted my
Samsung Notebook 9 is appearing in many other Samsung laptops. Expose
the quirk which fixed my laptop as a model so other users can try it.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=207423
Signed-off-by: Mike Pozulp <pozulp.kernel@gmail.com>
Link: https://lore.kernel.org/r/20200817043219.458889-1-pozulp.kernel@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When probing an interrupt controller that is behind a parent,
we try to check whether the parent domain is available as
an indication that we can actually try to probe.
Unfortunately, we are checking this with the firmware node of
the about to be probed device, not the parent. This is obviously
bound to fail.
Instead, use the parent node.
Fixes: f8410e626569 ("irqchip: Add IRQCHIP_PLATFORM_DRIVER_BEGIN/END and IRQCHIP_MATCH helper macros")
Reported-by: John Stultz <john.stultz@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
|
|
As the recent fix addressed the channel swap problem more properly,
update the comment as well.
Fixes: 1b7ecc241a67 ("ALSA: usb-audio: work around streaming quirk for MacroSilicon MS2109")
Signed-off-by: Hector Martin <marcan@marcan.st>
Link: https://lore.kernel.org/r/20200816084431.102151-1-marcan@marcan.st
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
DW DMA IP-core provides a way to synthesize the DMA controller with
channels having different parameters like maximum burst-length,
multi-block support, maximum data width, etc. Those parameters both
explicitly and implicitly affect the channels performance. Since DMA slave
devices might be very demanding to the DMA performance, let's provide a
functionality for the slaves to be assigned with DW DMA channels, which
performance according to the platform engineer fulfill their requirements.
After this patch is applied it can be done by passing the mask of suitable
DMA-channels either directly in the dw_dma_slave structure instance or as
a fifth cell of the DMA DT-property. If mask is zero or not provided, then
there is no limitation on the channels allocation.
For instance Baikal-T1 SoC is equipped with a DW DMAC engine, which first
two channels are synthesized with max burst length of 16, while the rest
of the channels have been created with max-burst-len=4. It would seem that
the first two channels must be faster than the others and should be more
preferable for the time-critical DMA slave devices. In practice it turned
out that the situation is quite the opposite. The channels with
max-burst-len=4 demonstrated a better performance than the channels with
max-burst-len=16 even when they both had been initialized with the same
settings. The performance drop of the first two DMA-channels made them
unsuitable for the DW APB SSI slave device. No matter what settings they
are configured with, full-duplex SPI transfers occasionally experience the
Rx FIFO overflow. It means that the DMA-engine doesn't keep up with
incoming data pace even though the SPI-bus is enabled with speed of 25MHz
while the DW DMA controller is clocked with 50MHz signal. There is no such
problem has been noticed for the channels synthesized with
max-burst-len=4.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200731200826.9292-6-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
According to the DW DMA controller Databook 2.18b (page 40 "3.5 Memory
Peripherals") memory peripherals don't have handshaking interface
connected to the controller, therefore they can never be a flow
controller. Since the CTLx.SRC_MSIZE and CTLx.DEST_MSIZE are properties
valid only for peripherals with a handshaking interface, we can freely
zero these fields out if the memory peripheral is selected to be the
source or the destination of the DMA transfers.
Note according to the databook, length of burst transfers to memory is
always equal to the number of data items available in a channel FIFO or
data items required to complete the block transfer, whichever is smaller;
length of burst transfers from memory is always equal to the space
available in a channel FIFO or number of data items required to complete
the block transfer, whichever is smaller.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200731200826.9292-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Indeed in case of the DMA_DEV_TO_MEM DMA transfers it's enough to take the
destination memory address and the destination master data width into
account to calculate the CTLx.DST_TR_WIDTH setting of the memory
peripheral. According to the DW DMAC IP-core Databook 2.18b (page 66,
Example 5) at the and of a DMA transfer when the DMA-channel internal FIFO
is left with data less than for a single destination burst transaction,
the destination peripheral will enter the Single Transaction Region where
the DW DMA controller can complete a block transfer to the destination
using single transactions (non-burst transaction of CTLx.DST_TR_WIDTH
bytes). If there is no enough data in the DMA-channel internal FIFO for
even a single non-burst transaction of CTLx.DST_TR_WIDTH bytes, then the
channel enters "FIFO flush mode". That mode is activated to empty the FIFO
and flush the leftovers out to the memory peripheral. The flushing
procedure is simple. The data is sent to the memory by means of a set of
single transaction of CTLx.SRC_TR_WIDTH bytes. To sum up it's redundant to
use the LLPs length to find out the CTLx.DST_TR_WIDTH parameter value,
since each DMA transfer will be completed with the CTLx.SRC_TR_WIDTH bytes
transaction if it is required.
We suggest to remove the LLP entry length from the statement which
calculates the memory peripheral DMA transaction width since it's
redundant due to the feature described above. By doing so we'll improve
the memory bus utilization and speed up the DMA-channel performance for
DMA_DEV_TO_MEM DMA-transfers.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200731200826.9292-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
CFGx.FIFO_MODE field controls a DMA-controller "FIFO readiness" criterion.
In other words it determines when to start pushing data out of a DW
DMAC channel FIFO to a destination peripheral or from a source
peripheral to the DW DMAC channel FIFO. Currently FIFO-mode is set to one
for all DW DMAC channels. It means they are tuned to flush data out of
FIFO (to a memory peripheral or by accepting the burst transaction
requests) when FIFO is at least half-full (except at the end of the block
transfer, when FIFO-flush mode is activated) and are configured to get
data to the FIFO when it's at least half-empty.
Such configuration is a good choice when there is no slave device involved
in the DMA transfers. In that case the number of bursts per block is less
than when CFGx.FIFO_MODE = 0 and, hence, the bus utilization will improve.
But the latency of DMA transfers may increase when CFGx.FIFO_MODE = 1,
since DW DMAC will wait for the channel FIFO contents to be either
half-full or half-empty depending on having the destination or the source
transfers. Such latencies might be dangerous in case if the DMA transfers
are expected to be performed from/to a slave device. Since normally
peripheral devices keep data in internal FIFOs, any latency at some
critical moment may cause one being overflown and consequently losing
data. This especially concerns a case when either a peripheral device is
relatively fast or the DW DMAC engine is relatively slow with respect to
the incoming data pace.
In order to solve problems, which might be caused by the latencies
described above, let's enable the FIFO half-full/half-empty "FIFO
readiness" criterion only for DMA transfers with no slave device involved.
Thanks to the commit 99ba8b9b0d97 ("dmaengine: dw: Initialize channel
before each transfer") we can freely do that in the generic
dw_dma_initialize_chan() method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200731200826.9292-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Each DW DMA controller channel can be synthesized with different
parameters like maximum burst-length, multi-block support, maximum data
width, etc. Most of these parameters determine the DW DMAC channels
performance in its own aspect. On the other hand these parameters can
be implicitly responsible for the channels performance degradation
(for instance multi-block support is a very useful feature, but having
it disabled during the DW DMAC synthesize will provide a more optimized
core). Since DMA slave devices may have critical dependency on the DMA
engine performance, let's provide a way for the slave devices to have
the DMA-channels allocated from a pool of the channels, which according
to the system engineer fulfill their performance requirements.
The pool is determined by a mask optionally specified in the fifth
DMA-cell of the DMA DT-property. If the fifth cell is omitted from the
phandle arguments or the mask is zero, then the allocation will be
performed from a set of all channels provided by the DMA controller.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200731200826.9292-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Expose statistics to debugfs when available. This helps debugging issues
with the DPDMA driver.
Signed-off-by: Hyun Kwon <hyun.kwon@xilinx.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200812171228.9751-1-laurent.pinchart@ideasonboard.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
of_dma_xlate callback can return ERR_PTR as well NULL in case of failure.
If error code is returned (not NULL) then the route should be released and
the router should not be registered for the channel.
Fixes: 56f13c0d9524c ("dmaengine: of_dma: Support for DMA routers")
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200806104928.25975-1-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The security accelerator within MCU domain supports two ports similarly
to the SA2UL in MAIN domain.
Add endpoint configuration for the two ingress and one egress threads of
the second port.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200803100724.19003-1-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add new PSI-L map file for the new TI j7200 SoC.
The DMA hardware in j7200 is the same as in j721e with different
set of peripherals resulting different PSI-L thread map compered
to j721e.
See J7200 Technical Reference Manual (SPRUIU1, June 2020)
for further details: https://www.ti.com/lit/pdf/spruiu1
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200803125713.17829-3-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Instead of separate of_machine_is_compatible() it is better to use
soc_device_match() and soc_device_attribute struct to get the PSI-L map
for the booted device.
By using soc_device_match() it is easier to add support for new devices.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20200803125713.17829-2-peter.ujfalusi@ti.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Move the clearing of misc interrupt cause to immediately after reading the
register in order to allow the next interrupt to be asserted.
Suggested-by: Nikhil Rao <nikhil.rao@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/159603824665.28647.5344356370364397996.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The of_device_id is included unconditionally by of.h header and used
in the driver as well. Remove of_match_ptr to fix W=1 compile test
warning with !CONFIG_OF:
drivers/dma/ti/omap-dma.c:1892:34: warning: 'omap_dma_match' defined but not used [-Wunused-const-variable=]
1892 | static const struct of_device_id omap_dma_match[] = {
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Link: https://lore.kernel.org/r/20200728170939.28278-1-krzk@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
We get the opp_table pointer at the top of the function and so we should
put the pointer at the end of the function like all other exit paths
from this function do.
Cc: v5.8+ <stable@vger.kernel.org> # v5.8+
Fixes: b00e667a6d8b ("opp: Remove bandwidth votes when target_freq is zero")
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
[ Viresh: Split the patch into two ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
We get the opp_table pointer at the top of the function and so we should
put the pointer at the end of the function like all other exit paths
from this function do.
Cc: v5.7+ <stable@vger.kernel.org> # v5.7+
Fixes: aca48b61f963 ("opp: Manage empty OPP tables with clk handle")
Reviewed-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
[ Viresh: Split the patch into two ]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
The state for WQs should be reset to disabled when a device is reset or
disabled.
Fixes: da32b28c95a7 ("dmaengine: idxd: cleanup workqueue config after disabling")
Reported-by: Mona Hossain <mona.hossain@intel.com>
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Link: https://lore.kernel.org/r/159586777684.27150.17589406415773568534.stgit@djiang5-desk3.ch.intel.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Drivers using legacy PM have to manage PCI states and device's PM states
themselves. They also need to take care of configuration registers.
With improved and powerful support of generic PM, PCI Core takes care of
above mentioned, device-independent, jobs.
This driver makes use of PCI helper functions like
pci_save/restore_state(), pci_enable/disable_device(),
and pci_set_power_state() to do required operations. In generic mode, they
are no longer needed.
Change function parameter in both .suspend() and .resume() to
"struct device*" type. Use dev_get_drvdata() to get drv data.
Compile-tested only.
Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200720113740.353479-1-vaibhavgupta40@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The acpi_get_table() should be coupled with acpi_put_table() if
the mapped table is not used at runtime to release the table
mapping, put the CSRT table buf after using it.
Signed-off-by: Hanjun Guo <guohanjun@huawei.com>
Link: https://lore.kernel.org/r/1595411661-15936-1-git-send-email-guohanjun@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Newer version of HSDK aka HSDK-4xD (with dual issue HS48x4 CPU) wired up
the perf interrupt, so enable that in DT.
This is OK for old HSDK where this irq is ignored because pct irq is not
wired up in hardware.
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Current code inadventely bails if hardware supports sampling/overflow
interrupts, but the irq is missing from device tree.
|
| # perf stat -e cycles,instructions,major-faults,minor-faults ../hackbench
| Running with 10 groups 400 process
| Time: 0.921
|
| Performance counter stats for '../hackbench':
|
| <not supported> cycles
| <not supported> instructions
| 0 major-faults
| 8679 minor-faults
This need not be as we can still do simple counting based perf stat.
This unborks perf on HSDK-4xD
Cc: <stable@vger.kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
Drop the repeated word "to".
Change "Thay" to "That".
Add a closing right parenthesis.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: linux-snps-arc@lists.infradead.org
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
__machine_check_early_realmode_p*() are currently declared as extern
in cputable.c and because of this when compiled with "C=1" (which
enables semantic checker) produces these warnings.
CHECK arch/powerpc/kernel/mce_power.c
arch/powerpc/kernel/mce_power.c:709:6: warning: symbol '__machine_check_early_realmode_p7' was not declared. Should it be static?
arch/powerpc/kernel/mce_power.c:717:6: warning: symbol '__machine_check_early_realmode_p8' was not declared. Should it be static?
arch/powerpc/kernel/mce_power.c:722:6: warning: symbol '__machine_check_early_realmode_p9' was not declared. Should it be static?
arch/powerpc/kernel/mce_power.c:740:6: warning: symbol '__machine_check_early_realmode_p10' was not declared. Should it be static?
Patch here moves the declaration to asm/mce.h and includes the same in
cputable.c
Fixes: ae744f3432d3 ("powerpc/book3s: Flush SLB/TLBs if we get SLB/TLB machine check errors on power8")
Fixes: 7b9f71f974a1 ("powerpc/64s: POWER9 machine check handler")
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200817005618.3305028-1-maddy@linux.ibm.com
|
|
This fix wasn't correct: When this function is invoked from the
retransmission worker, the iterator contains garbage and resetting
it causes a crash.
As the work queue should not be performance critical also zero the
msghdr struct.
Fixes: 35759383133f64d "(mptcp: sendmsg: reset iter on error)"
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a raw mode cputable entry for POWER10. Copies most of the fields
from commit a3ea40d5c736 ("powerpc: Add POWER10 architected mode")
except for oprofile_cpu_type, machine_check_early, pvr_mask and
pvr_mask fields. On bare metal systems we use DT CPU features, which
doesn't need a cputable entry. But in VMs we still rely on the raw
cputable entry to set the correct values for the PMU related fields.
Fixes: a3ea40d5c736 ("powerpc: Add POWER10 architected mode")
Signed-off-by: Madhavan Srinivasan <maddy@linux.ibm.com>
[mpe: Reorder vs cleanup patch and add Fixes tag]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200817005618.3305028-2-maddy@linux.ibm.com
|
|
It is possible to trigger this WARN_ON from user space by triggering a
devlink snapshot with an ID which already exists. We don't need both
-EEXISTS being reported and spamming the kernel log.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Chris Healy <cphealy@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using ipv6_dev_find() in one module, it requires ipv6 not to
work as a module. Otherwise, this error occurs in build:
undefined reference to `ipv6_dev_find'.
So fix it by adding "depends on IPV6 || IPV6=n" to tipc/Kconfig,
as it does in sctp/Kconfig.
Fixes: 5a6f6f579178 ("tipc: set ub->ifindex for local ipv6 address")
Reported-by: kernel test robot <lkp@intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__tipc_nl_compat_dumpit() has two callers, and it expects them to
pass a valid nlmsghdr via arg->data. This header is artificial and
crafted just for __tipc_nl_compat_dumpit().
tipc_nl_compat_publ_dump() does so by putting a genlmsghdr as well
as some nested attribute, TIPC_NLA_SOCK. But the other caller
tipc_nl_compat_dumpit() does not, this leaves arg->data uninitialized
on this call path.
Fix this by just adding a similar nlmsghdr without any payload in
tipc_nl_compat_dumpit().
This bug exists since day 1, but the recent commit 6ea67769ff33
("net: tipc: prepare attrs in __tipc_nl_compat_dumpit()") makes it
easier to appear.
Reported-and-tested-by: syzbot+0e7181deafa7e0b79923@syzkaller.appspotmail.com
Fixes: d0796d1ef63d ("tipc: convert legacy nl bearer dump to nl compat")
Cc: Jon Maloy <jmaloy@redhat.com>
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Richard Alpe <richard.alpe@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Using ata_link_info() instead of ata_link_printk().
Signed-off-by: Xu Wang <vulab@iscas.ac.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
