| Age | Commit message (Collapse) | Author |
|---|
|
Set NETIF_F_GSO_UDP_L4 bit of hw_features and features because i.MX95
enetc and LS1028A driver implements UDP segmentation.
- i.MX95 ENETC supports UDP segmentation via LSO.
- LS1028A ENETC supports UDP segmentation since the commit 3d5b459ba0e3
("net: tso: add UDP segmentation support").
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Link: https://patch.msgid.link/20241219054755.1615626-5-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ENETC rev 4.1 supports large send offload (LSO), segmenting large TCP
and UDP transmit units into multiple Ethernet frames. To support LSO,
software needs to fill some auxiliary information in Tx BD, such as LSO
header length, frame length, LSO maximum segment size, etc.
At 1Gbps link rate, TCP segmentation was tested using iperf3, and the
CPU performance before and after applying the patch was compared through
the top command. It can be seen that LSO saves a significant amount of
CPU cycles compared to software TSO.
Before applying the patch:
%Cpu(s): 0.1 us, 4.1 sy, 0.0 ni, 85.7 id, 0.0 wa, 0.5 hi, 9.7 si
After applying the patch:
%Cpu(s): 0.1 us, 2.3 sy, 0.0 ni, 94.5 id, 0.0 wa, 0.4 hi, 2.6 si
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://patch.msgid.link/20241219054755.1615626-4-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The max chained Tx BDs of latest ENETC (i.MX95 ENETC, rev 4.1) has been
increased to 63, but since the range of MAX_SKB_FRAGS is 17~45, so for
i.MX95 ENETC and later revision, it is better to set ENETC4_MAX_SKB_FRAGS
to MAX_SKB_FRAGS.
In addition, add max_frags in struct enetc_drvdata to indicate the max
chained BDs supported by device. Because the max number of chained BDs
supported by LS1028A and i.MX95 ENETC is different.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20241219054755.1615626-3-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In addition to supporting Rx checksum offload, i.MX95 ENETC also supports
Tx checksum offload. The transmit checksum offload is implemented through
the Tx BD. To support Tx checksum offload, software needs to fill some
auxiliary information in Tx BD, such as IP version, IP header offset and
size, whether L4 is UDP or TCP, etc.
Same as Rx checksum offload, Tx checksum offload capability isn't defined
in register, so tx_csum bit is added to struct enetc_drvdata to indicate
whether the device supports Tx checksum offload.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Reviewed-by: Frank Li <Frank.Li@nxp.com>
Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Link: https://patch.msgid.link/20241219054755.1615626-2-wei.fang@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Current implementation of stmmac_probe_config_dt() does not release the
OF node reference obtained by of_parse_phandle() in some error paths.
The problem is that some error paths call stmmac_remove_config_dt() to
clean up but others use and unwind ladder. These two types of error
handling have not kept in sync and have been a recurring source of bugs.
Re-write the error handling in stmmac_probe_config_dt() to use an unwind
ladder. Consequently, stmmac_remove_config_dt() is not needed anymore,
thus remove it.
This bug was found by an experimental verification tool that I am
developing.
Fixes: 4838a5405028 ("net: stmmac: Fix wrapper drivers not detecting PHY")
Signed-off-by: Joe Hattori <joe@pf.is.s.u-tokyo.ac.jp>
Link: https://patch.msgid.link/20241219024119.2017012-1-joe@pf.is.s.u-tokyo.ac.jp
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The CSR dump support leverages the FBNIC_BOUNDS macro, which pads the end
condition for each section by adding an offset of 1. However, the RPC RAM
section, which is dumped differently from other sections, does not rely
on this macro and instead directly uses end boundary address. Hence,
subtracting 1 from the end address results in skipping a register.
Fixes 3d12862b216d (“eth: fbnic: Add support to dump registers”)
Signed-off-by: Mohsin Bashir <mohsin.bashr@gmail.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Link: https://patch.msgid.link/20241218232614.439329-1-mohsin.bashr@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If userspace holds an fd open, unbinds the device and then closes it,
the driver shouldn't try to access the hardware. Protect it by using
drm_dev_enter()/drm_dev_exit(). This fixes the following page fault:
<6> [IGT] xe_wedged: exiting, ret=98
<1> BUG: unable to handle page fault for address: ffffc901bc5e508c
<1> #PF: supervisor read access in kernel mode
<1> #PF: error_code(0x0000) - not-present page
...
<4> xe_lrc_update_timestamp+0x1c/0xd0 [xe]
<4> xe_exec_queue_update_run_ticks+0x50/0xb0 [xe]
<4> xe_exec_queue_fini+0x16/0xb0 [xe]
<4> __guc_exec_queue_fini_async+0xc4/0x190 [xe]
<4> guc_exec_queue_fini_async+0xa0/0xe0 [xe]
<4> guc_exec_queue_fini+0x23/0x40 [xe]
<4> xe_exec_queue_destroy+0xb3/0xf0 [xe]
<4> xe_file_close+0xd4/0x1a0 [xe]
<4> drm_file_free+0x210/0x280 [drm]
<4> drm_close_helper.isra.0+0x6d/0x80 [drm]
<4> drm_release_noglobal+0x20/0x90 [drm]
Fixes: 514447a12190 ("drm/xe: Stop accumulating LRC timestamp on job_free")
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/3421
Reviewed-by: Umesh Nerlige Ramappa <umesh.nerlige.ramappa@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241218053122.2730195-1-lucas.demarchi@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
(cherry picked from commit 4ca1fd418338d4d135428a0eb1e16e3b3ce17ee8)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
There is a typo in function call and instead of VF LMEM we were
looking at VF GGTT provisioning. Fix that.
Fixes: 234670cea9a2 ("drm/xe/pf: Skip fair VFs provisioning if already provisioned")
Signed-off-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Cc: Piotr Piórkowski <piotr.piorkowski@intel.com>
Reviewed-by: Himal Prasad Ghimiray <himal.prasad.ghimiray@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241216223253.819-1-michal.wajdeczko@intel.com
(cherry picked from commit a8d0aa0e7fcd20c9f1992688c0f0d07a68287403)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
Fix a potential GPU page fault during tt -> system moves by waiting for
migration jobs to complete before unmapping SG. This ensures that IOMMU
mappings are not prematurely torn down while a migration job is still in
progress.
v2: Use intr=false(Matt A)
v3: Update commit message(Matt A)
v4: s/DMA_RESV_USAGE_BOOKKEEP/DMA_RESV_USAGE_KERNEL(Thomas)
Closes: https://gitlab.freedesktop.org/drm/xe/kernel/-/issues/3466
Fixes: 75521e8b56e8 ("drm/xe: Perform dma_map when moving system buffer objects to TT")
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: stable@vger.kernel.org # v6.11+
Cc: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241213122415.3880017-2-nirmoy.das@intel.com
Signed-off-by: Nirmoy Das <nirmoy.das@intel.com>
(cherry picked from commit cda06412c06893a6f07a2fbf89d42a0972ec9e8e)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
Ensure a non-interruptible wait is used when moving a bo to
XE_PL_SYSTEM. This prevents dma_mappings from being removed prematurely
while a GPU job is still in progress, even if the CPU receives a
signal during the operation.
Fixes: 75521e8b56e8 ("drm/xe: Perform dma_map when moving system buffer objects to TT")
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Matthew Brost <matthew.brost@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: stable@vger.kernel.org # v6.11+
Suggested-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241213122415.3880017-1-nirmoy.das@intel.com
Signed-off-by: Nirmoy Das <nirmoy.das@intel.com>
(cherry picked from commit dc5e20ae1f8a7c354dc9833faa2720254e5a5443)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
There is a mesa debug tool for decoding devcoredump files. Recent
changes to improve the devcoredump output broke that tool. So revert
the changes until the tool can be extended to support the new fields.
Signed-off-by: John Harrison <John.C.Harrison@Intel.com>
Fixes: c28fd6c358db ("drm/xe/devcoredump: Improve section headings and add tile info")
Fixes: ec1455ce7e35 ("drm/xe/devcoredump: Add ASCII85 dump helper function")
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Julia Filipchuk <julia.filipchuk@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: intel-xe@lists.freedesktop.org
Reviewed-by: Jonathan Cavitt <jonathan.cavitt@intel.com>
Reviewed-by: José Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20241213172833.1733376-1-John.C.Harrison@Intel.com
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
(cherry picked from commit 70fb86a85dc9fd66014d7eb2fe356f50702ceeb6)
Signed-off-by: Thomas Hellström <thomas.hellstrom@linux.intel.com>
|
|
update
Make sure the trace_kprobe's module notifer callback function is called
after jump_label's callback is called. Since the trace_kprobe's callback
eventually checks jump_label address during registering new kprobe on
the loading module, jump_label must be updated before this registration
happens.
Link: https://lore.kernel.org/all/173387585556.995044.3157941002975446119.stgit@devnote2/
Fixes: 614243181050 ("tracing/kprobes: Support module init function probing")
Signed-off-by: Masami Hiramatsu (Google) <mhiramat@kernel.org>
|
|
Flush CQE handler has not been called if QP state gets into errored
mode in DWQE path. So, the new added outstanding WQEs will never be
flushed.
It leads to a hung task timeout when using NFS over RDMA:
__switch_to+0x7c/0xd0
__schedule+0x350/0x750
schedule+0x50/0xf0
schedule_timeout+0x2c8/0x340
wait_for_common+0xf4/0x2b0
wait_for_completion+0x20/0x40
__ib_drain_sq+0x140/0x1d0 [ib_core]
ib_drain_sq+0x98/0xb0 [ib_core]
rpcrdma_xprt_disconnect+0x68/0x270 [rpcrdma]
xprt_rdma_close+0x20/0x60 [rpcrdma]
xprt_autoclose+0x64/0x1cc [sunrpc]
process_one_work+0x1d8/0x4e0
worker_thread+0x154/0x420
kthread+0x108/0x150
ret_from_fork+0x10/0x18
Fixes: 01584a5edcc4 ("RDMA/hns: Add support of direct wqe")
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20241220055249.146943-5-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
WARN_ON() is called in the IO path. And it could lead to a warning
storm. Use WARN_ON_ONCE() instead of WARN_ON().
Fixes: 12542f1de179 ("RDMA/hns: Refactor process about opcode in post_send()")
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20241220055249.146943-4-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
If it fails to modify QP to RTR, dip_ctx will not be attached. And
during detroying QP, the invalid dip_ctx pointer will be accessed.
Fixes: faa62440a577 ("RDMA/hns: Fix different dgids mapping to the same dip_idx")
Signed-off-by: Chengchang Tang <tangchengchang@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20241220055249.146943-3-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Due to HW limitation, the three region of WQE buffer must be mapped
and set to HW in a fixed order: SQ buffer, SGE buffer, and RQ buffer.
Currently when one region is zero-hop while the other two are not,
the zero-hop region will not be mapped. This violate the limitation
above and leads to address error.
Fixes: 38389eaa4db1 ("RDMA/hns: Add mtr support for mixed multihop addressing")
Signed-off-by: wenglianfa <wenglianfa@huawei.com>
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20241220055249.146943-2-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
The last use of is_server_using_iface() was removed in 2022 by
commit aa45dadd34e4 ("cifs: change iface_list from array to sorted linked
list")
Remove it.
Signed-off-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
Previously, deferred file handles were reused only for read
operations, this commit extends to reusing deferred handles
for write operations. By reusing these handles we can reduce
the need for open/close operations over the wire.
Signed-off-by: Bharath SM <bharathsm@microsoft.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
If a UDP socket changes its local address while it's receiving
datagrams, as a result of connect(), there is a period during which
a lookup operation might fail to find it, after the address is changed
but before the secondary hash (port and address) and the four-tuple
hash (local and remote ports and addresses) are updated.
Secondary hash chains were introduced by commit 30fff9231fad ("udp:
bind() optimisation") and, as a result, a rehash operation became
needed to make a bound socket reachable again after a connect().
This operation was introduced by commit 719f835853a9 ("udp: add
rehash on connect()") which isn't however a complete fix: the
socket will be found once the rehashing completes, but not while
it's pending.
This is noticeable with a socat(1) server in UDP4-LISTEN mode, and a
client sending datagrams to it. After the server receives the first
datagram (cf. _xioopen_ipdgram_listen()), it issues a connect() to
the address of the sender, in order to set up a directed flow.
Now, if the client, running on a different CPU thread, happens to
send a (subsequent) datagram while the server's socket changes its
address, but is not rehashed yet, this will result in a failed
lookup and a port unreachable error delivered to the client, as
apparent from the following reproducer:
LEN=$(($(cat /proc/sys/net/core/wmem_default) / 4))
dd if=/dev/urandom bs=1 count=${LEN} of=tmp.in
while :; do
taskset -c 1 socat UDP4-LISTEN:1337,null-eof OPEN:tmp.out,create,trunc &
sleep 0.1 || sleep 1
taskset -c 2 socat OPEN:tmp.in UDP4:localhost:1337,shut-null
wait
done
where the client will eventually get ECONNREFUSED on a write()
(typically the second or third one of a given iteration):
2024/11/13 21:28:23 socat[46901] E write(6, 0x556db2e3c000, 8192): Connection refused
This issue was first observed as a seldom failure in Podman's tests
checking UDP functionality while using pasta(1) to connect the
container's network namespace, which leads us to a reproducer with
the lookup error resulting in an ICMP packet on a tap device:
LOCAL_ADDR="$(ip -j -4 addr show|jq -rM '.[] | .addr_info[0] | select(.scope == "global").local')"
while :; do
./pasta --config-net -p pasta.pcap -u 1337 socat UDP4-LISTEN:1337,null-eof OPEN:tmp.out,create,trunc &
sleep 0.2 || sleep 1
socat OPEN:tmp.in UDP4:${LOCAL_ADDR}:1337,shut-null
wait
cmp tmp.in tmp.out
done
Once this fails:
tmp.in tmp.out differ: char 8193, line 29
we can finally have a look at what's going on:
$ tshark -r pasta.pcap
1 0.000000 :: ? ff02::16 ICMPv6 110 Multicast Listener Report Message v2
2 0.168690 88.198.0.161 ? 88.198.0.164 UDP 8234 60260 ? 1337 Len=8192
3 0.168767 88.198.0.161 ? 88.198.0.164 UDP 8234 60260 ? 1337 Len=8192
4 0.168806 88.198.0.161 ? 88.198.0.164 UDP 8234 60260 ? 1337 Len=8192
5 0.168827 c6:47:05:8d:dc:04 ? Broadcast ARP 42 Who has 88.198.0.161? Tell 88.198.0.164
6 0.168851 9a:55:9a:55:9a:55 ? c6:47:05:8d:dc:04 ARP 42 88.198.0.161 is at 9a:55:9a:55:9a:55
7 0.168875 88.198.0.161 ? 88.198.0.164 UDP 8234 60260 ? 1337 Len=8192
8 0.168896 88.198.0.164 ? 88.198.0.161 ICMP 590 Destination unreachable (Port unreachable)
9 0.168926 88.198.0.161 ? 88.198.0.164 UDP 8234 60260 ? 1337 Len=8192
10 0.168959 88.198.0.161 ? 88.198.0.164 UDP 8234 60260 ? 1337 Len=8192
11 0.168989 88.198.0.161 ? 88.198.0.164 UDP 4138 60260 ? 1337 Len=4096
12 0.169010 88.198.0.161 ? 88.198.0.164 UDP 42 60260 ? 1337 Len=0
On the third datagram received, the network namespace of the container
initiates an ARP lookup to deliver the ICMP message.
In another variant of this reproducer, starting the client with:
strace -f pasta --config-net -u 1337 socat UDP4-LISTEN:1337,null-eof OPEN:tmp.out,create,trunc 2>strace.log &
and connecting to the socat server using a loopback address:
socat OPEN:tmp.in UDP4:localhost:1337,shut-null
we can more clearly observe a sendmmsg() call failing after the
first datagram is delivered:
[pid 278012] connect(173, 0x7fff96c95fc0, 16) = 0
[...]
[pid 278012] recvmmsg(173, 0x7fff96c96020, 1024, MSG_DONTWAIT, NULL) = -1 EAGAIN (Resource temporarily unavailable)
[pid 278012] sendmmsg(173, 0x561c5ad0a720, 1, MSG_NOSIGNAL) = 1
[...]
[pid 278012] sendmmsg(173, 0x561c5ad0a720, 1, MSG_NOSIGNAL) = -1 ECONNREFUSED (Connection refused)
and, somewhat confusingly, after a connect() on the same socket
succeeded.
Until commit 4cdeeee9252a ("net: udp: prefer listeners bound to an
address"), the race between receive address change and lookup didn't
actually cause visible issues, because, once the lookup based on the
secondary hash chain failed, we would still attempt a lookup based on
the primary hash (destination port only), and find the socket with the
outdated secondary hash.
That change, however, dropped port-only lookups altogether, as side
effect, making the race visible.
To fix this, while avoiding the need to make address changes and
rehash atomic against lookups, reintroduce primary hash lookups as
fallback, if lookups based on four-tuple and secondary hashes fail.
To this end, introduce a simplified lookup implementation, which
doesn't take care of SO_REUSEPORT groups: if we have one, there are
multiple sockets that would match the four-tuple or secondary hash,
meaning that we can't run into this race at all.
v2:
- instead of synchronising lookup operations against address change
plus rehash, reintroduce a simplified version of the original
primary hash lookup as fallback
v1:
- fix build with CONFIG_IPV6=n: add ifdef around sk_v6_rcv_saddr
usage (Kuniyuki Iwashima)
- directly use sk_rcv_saddr for IPv4 receive addresses instead of
fetching inet_rcv_saddr (Kuniyuki Iwashima)
- move inet_update_saddr() to inet_hashtables.h and use that
to set IPv4/IPv6 addresses as suitable (Kuniyuki Iwashima)
- rebase onto net-next, update commit message accordingly
Reported-by: Ed Santiago <santiago@redhat.com>
Link: https://github.com/containers/podman/issues/24147
Analysed-by: David Gibson <david@gibson.dropbear.id.au>
Fixes: 30fff9231fad ("udp: bind() optimisation")
Signed-off-by: Stefano Brivio <sbrivio@redhat.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The default switch case ends with a return; meaning this return is
never reached.
Coverity-ID: 1497123
Signed-off-by: Ariel Otilibili <ariel.otilibili-anieli@eurecom.fr>
Link: https://patch.msgid.link/20241221111454.1074285-4-ariel.otilibili-anieli@eurecom.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The extended match rule em_canid is used to classify CAN frames based
on their CAN Identifier. To keep the CAN maintainers in the loop for
relevant changes which might affect the CAN specific functionality add
em_canid.c to the CAN NETWORK LAYER files.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20241219190837.3087-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Map my retired company address and an accidentally used personal
mail address within mailmap.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://patch.msgid.link/20241130170911.2828-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Convert old text based binding to json schema.
Changes during conversion:
- Add a fallback for `microchip,sam9x60-can` as it is compatible with the
CAN IP core on `atmel,at91sam9x5-can`.
- Add the required properties `clock` and `clock-names`, which were
missing in the original binding.
- Update examples and include appropriate file directives to resolve
errors identified by `dt_binding_check` and `dtbs_check`.
Signed-off-by: Charan Pedumuru <charan.pedumuru@microchip.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20241120-can-v3-1-da5bb4f6128d@microchip.com
[mkl: fixed indention in example]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
tcan4x5x devices only requires the clock "cclk", so call
devm_clk_get() directly. This is done to avoid
m_can_class_get_clocks() that checks for both hclk and cclk and
results in this warning message:
| tcan4x5x spi0.0: no clock found
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Link: https://patch.msgid.link/20241128-mcancclk-v1-1-a93aac64dbae@geanix.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Throughout the sun4i_can_err() function, the likely() macro is used to
check the skb buffer, except in one instance. This patch makes the code
consistent by using the macro in that case as well.
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Link: https://patch.msgid.link/20241122221650.633981-4-dario.binacchi@amarulasolutions.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Sean Nyekjaer <sean@geanix.com> says:
This series adds support for setting the nWKRQ voltage.
Link: https://patch.msgid.link/20241114-tcan-wkrqv-v5-0-a2d50833ed71@geanix.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The nWKRQ pin supports an output voltage of either the internal reference
voltage (3.6V) or the reference voltage of
the digital interface 0-6V (VIO).
Add the devicetree option ti,nwkrq-voltage-vio to set it to VIO.
If this property is omitted the reset default, the internal reference
voltage, is used.
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://patch.msgid.link/20241114-tcan-wkrqv-v5-2-a2d50833ed71@geanix.com
[mkl: remove unused variable in tcan4x5x_get_dt_data()]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Since the dynamic preemption has been enabled for PREEMPT_RT we have now
CONFIG_PREEMPT and CONFIG_PREEMPT_RT set simultaneously. This affects
the vermagic strings which comes now PREEMPT with PREEMPT_RT enabled.
The PREEMPT_RT module usually can not be loaded on a PREEMPT kernel
because some symbols are missing.
However if the symbols are fine then it continues and it crashes later.
The problem is that the struct module has a different layout and the
num_exentries or init members are at a different position leading to a
crash later on. This is not necessary caught by the size check in
elf_validity_cache_index_mod() because the mem member has an alignment
requirement of __module_memory_align which is big enough keep the total
size unchanged. Therefore we should keep the string accurate instead of
removing it.
Move the PREEMPT_RT check before the PREEMPT so that it takes precedence
if both symbols are enabled.
Fixes: 35772d627b55c ("sched: Enable PREEMPT_DYNAMIC for PREEMPT_RT")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Petr Pavlu <petr.pavlu@suse.com>
Link: https://lore.kernel.org/r/20241205160602.3lIAsJRT@linutronix.de
Signed-off-by: Petr Pavlu <petr.pavlu@suse.com>
|
|
|
|
Pull KVM x86 fixes from Paolo Bonzini:
- Disable AVIC on SNP-enabled systems that don't allow writes to the
virtual APIC page, as such hosts will hit unexpected RMP #PFs in the
host when running VMs of any flavor.
- Fix a WARN in the hypercall completion path due to KVM trying to
determine if a guest with protected register state is in 64-bit mode
(KVM's ABI is to assume such guests only make hypercalls in 64-bit
mode).
- Allow the guest to write to supported bits in MSR_AMD64_DE_CFG to fix
a regression with Windows guests, and because KVM's read-only
behavior appears to be entirely made up.
- Treat TDP MMU faults as spurious if the faulting access is allowed
given the existing SPTE. This fixes a benign WARN (other than the
WARN itself) due to unexpectedly replacing a writable SPTE with a
read-only SPTE.
- Emit a warning when KVM is configured with ignore_msrs=1 and also to
hide the MSRs that the guest is looking for from the kernel logs.
ignore_msrs can trick guests into assuming that certain processor
features are present, and this in turn leads to bogus bug reports.
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: x86: let it be known that ignore_msrs is a bad idea
KVM: VMX: don't include '<linux/find.h>' directly
KVM: x86/mmu: Treat TDP MMU faults as spurious if access is already allowed
KVM: SVM: Allow guest writes to set MSR_AMD64_DE_CFG bits
KVM: x86: Play nice with protected guests in complete_hypercall_exit()
KVM: SVM: Disable AVIC on SNP-enabled system without HvInUseWrAllowed feature
|
|
KVM x86 fixes for 6.13:
- Disable AVIC on SNP-enabled systems that don't allow writes to the virtual
APIC page, as such hosts will hit unexpected RMP #PFs in the host when
running VMs of any flavor.
- Fix a WARN in the hypercall completion path due to KVM trying to determine
if a guest with protected register state is in 64-bit mode (KVM's ABI is to
assume such guests only make hypercalls in 64-bit mode).
- Allow the guest to write to supported bits in MSR_AMD64_DE_CFG to fix a
regression with Windows guests, and because KVM's read-only behavior appears
to be entirely made up.
- Treat TDP MMU faults as spurious if the faulting access is allowed given the
existing SPTE. This fixes a benign WARN (other than the WARN itself) due to
unexpectedly replacing a writable SPTE with a read-only SPTE.
|
|
When running KVM with ignore_msrs=1 and report_ignored_msrs=0, the user has
no clue that that the guest is being lied to. This may cause bug reports
such as https://gitlab.com/qemu-project/qemu/-/issues/2571, where enabling
a CPUID bit in QEMU caused Linux guests to try reading MSR_CU_DEF_ERR; and
being lied about the existence of MSR_CU_DEF_ERR caused the guest to assume
other things about the local APIC which were not true:
Sep 14 12:02:53 kernel: mce: [Firmware Bug]: Your BIOS is not setting up LVT offset 0x2 for deferred error IRQs correctly.
Sep 14 12:02:53 kernel: unchecked MSR access error: RDMSR from 0x852 at rIP: 0xffffffffb548ffa7 (native_read_msr+0x7/0x40)
Sep 14 12:02:53 kernel: Call Trace:
...
Sep 14 12:02:53 kernel: native_apic_msr_read+0x20/0x30
Sep 14 12:02:53 kernel: setup_APIC_eilvt+0x47/0x110
Sep 14 12:02:53 kernel: mce_amd_feature_init+0x485/0x4e0
...
Sep 14 12:02:53 kernel: [Firmware Bug]: cpu 0, try to use APIC520 (LVT offset 2) for vector 0xf4, but the register is already in use for vector 0x0 on this cpu
Without reported_ignored_msrs=0 at least the host kernel log will contain
enough information to avoid going on a wild goose chase. But if reports
about individual MSR accesses are being silenced too, at least complain
loudly the first time a VM is started.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The header clearly states that it does not want to be included directly,
only via '<linux/bitmap.h>'. Replace the include accordingly.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Message-ID: <20241217070539.2433-2-wsa+renesas@sang-engineering.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree fixes from Rob Herring:
- Disable #address-cells/#size-cells warning on coreboot (Chromebooks)
platforms
- Add missing root #address-cells/#size-cells in default empty DT
- Fix uninitialized variable in of_irq_parse_one()
- Fix interrupt-map cell length check in of_irq_parse_imap_parent()
- Fix refcount handling in __of_get_dma_parent()
- Fix error path in of_parse_phandle_with_args_map()
- Fix dma-ranges handling with flags cells
- Drop explicit fw_devlink handling of 'interrupt-parent'
- Fix "compression" typo in fixed-partitions binding
- Unify "fsl,liodn" property type definitions
* tag 'devicetree-fixes-for-6.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux:
of: Add coreboot firmware to excluded default cells list
of/irq: Fix using uninitialized variable @addr_len in API of_irq_parse_one()
of/irq: Fix interrupt-map cell length check in of_irq_parse_imap_parent()
of: Fix refcount leakage for OF node returned by __of_get_dma_parent()
of: Fix error path in of_parse_phandle_with_args_map()
dt-bindings: mtd: fixed-partitions: Fix "compression" typo
of: Add #address-cells/#size-cells in the device-tree root empty node
dt-bindings: Unify "fsl,liodn" type definitions
of: address: Preserve the flags portion on 1:1 dma-ranges mapping
of/unittest: Add empty dma-ranges address translation tests
of: property: fw_devlink: Do not use interrupt-parent directly
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC fixes from Arnd Bergmann:
"Two more small fixes, correcting the cacheline size on Raspberry Pi 5
and fixing a logic mistake in the microchip mpfs firmware driver"
* tag 'soc-fixes-6.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: dts: broadcom: Fix L2 linesize for Raspberry Pi 5
firmware: microchip: fix UL_IAP lock check in mpfs_auto_update_state()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc fixes from Andrew Morton:
"25 hotfixes. 16 are cc:stable. 19 are MM and 6 are non-MM.
The usual bunch of singletons and doubletons - please see the relevant
changelogs for details"
* tag 'mm-hotfixes-stable-2024-12-21-12-09' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (25 commits)
mm: huge_memory: handle strsep not finding delimiter
alloc_tag: fix set_codetag_empty() when !CONFIG_MEM_ALLOC_PROFILING_DEBUG
alloc_tag: fix module allocation tags populated area calculation
mm/codetag: clear tags before swap
mm/vmstat: fix a W=1 clang compiler warning
mm: convert partially_mapped set/clear operations to be atomic
nilfs2: fix buffer head leaks in calls to truncate_inode_pages()
vmalloc: fix accounting with i915
mm/page_alloc: don't call pfn_to_page() on possibly non-existent PFN in split_large_buddy()
fork: avoid inappropriate uprobe access to invalid mm
nilfs2: prevent use of deleted inode
zram: fix uninitialized ZRAM not releasing backing device
zram: refuse to use zero sized block device as backing device
mm: use clear_user_(high)page() for arch with special user folio handling
mm: introduce cpu_icache_is_aliasing() across all architectures
mm: add RCU annotation to pte_offset_map(_lock)
mm: correctly reference merged VMA
mm: use aligned address in copy_user_gigantic_page()
mm: use aligned address in clear_gigantic_page()
mm: shmem: fix ShmemHugePages at swapout
...
|
|
My tests run an allyesconfig build and it failed with the following errors:
LD [M] samples/kfifo/dma-example.ko
ld.lld: error: undefined symbol: nec7210_board_reset
ld.lld: error: undefined symbol: nec7210_read
ld.lld: error: undefined symbol: nec7210_write
It appears that some modules call the function nec7210_board_reset()
that is defined in nec7210.c. In an allyesconfig build, these other
modules are built in. But the file that holds nec7210_board_reset()
has:
obj-m += nec7210.o
Where that "-m" means it only gets built as a module. With the other
modules built in, they have no access to nec7210_board_reset() and the build
fails.
This isn't the only function. After fixing that one, I hit another:
ld.lld: error: undefined symbol: push_gpib_event
ld.lld: error: undefined symbol: gpib_match_device_path
Where push_gpib_event() was also used outside of the file it was defined
in, and that file too only was built as a module.
Since the directory that nec7210.c is only traversed when
CONFIG_GPIB_NEC7210 is set, and the directory with gpib_common.c is only
traversed when CONFIG_GPIB_COMMON is set, use those configs as the
option to build those modules. When it is an allyesconfig, then they
will both be built in and their functions will be available to the other
modules that are also built in.
Fixes: 3ba84ac69b53e ("staging: gpib: Add nec7210 GPIB chip driver")
Fixes: 9dde4559e9395 ("staging: gpib: Add GPIB common core driver")
Signed-off-by: Steven Rostedt (Google) <rostedt@goodmis.org>
Reviewed-by: Palmer Dabbelt <palmer@rivosinc.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild
Pull Kbuild fixes from Masahiro Yamada:
- Remove stale code in usr/include/headers_check.pl
- Fix issues in the user-mode-linux Debian package
- Fix false-positive "export twice" errors in modpost
* tag 'kbuild-fixes-v6.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
modpost: distinguish same module paths from different dump files
kbuild: deb-pkg: Do not install maint scripts for arch 'um'
kbuild: deb-pkg: add debarch for ARCH=um
kbuild: Drop support for include/asm-<arch> in headers_check.pl
|
|
Pull BPF fixes from Daniel Borkmann:
- Fix inlining of bpf_get_smp_processor_id helper for !CONFIG_SMP
systems (Andrea Righi)
- Fix BPF USDT selftests helper code to use asm constraint "m" for
LoongArch (Tiezhu Yang)
- Fix BPF selftest compilation error in get_uprobe_offset when
PROCMAP_QUERY is not defined (Jerome Marchand)
- Fix BPF bpf_skb_change_tail helper when used in context of BPF
sockmap to handle negative skb header offsets (Cong Wang)
- Several fixes to BPF sockmap code, among others, in the area of
socket buffer accounting (Levi Zim, Zijian Zhang, Cong Wang)
* tag 'bpf-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: Test bpf_skb_change_tail() in TC ingress
selftests/bpf: Introduce socket_helpers.h for TC tests
selftests/bpf: Add a BPF selftest for bpf_skb_change_tail()
bpf: Check negative offsets in __bpf_skb_min_len()
tcp_bpf: Fix copied value in tcp_bpf_sendmsg
skmsg: Return copied bytes in sk_msg_memcopy_from_iter
tcp_bpf: Add sk_rmem_alloc related logic for tcp_bpf ingress redirection
tcp_bpf: Charge receive socket buffer in bpf_tcp_ingress()
selftests/bpf: Fix compilation error in get_uprobe_offset()
selftests/bpf: Use asm constraint "m" for LoongArch
bpf: Fix bpf_get_smp_processor_id() on !CONFIG_SMP
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- fix a clang build issue with mediatec vcodec
- add missing variable initialization to dib3000mb write function
* tag 'media/v6.13-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
media: mediatek: vcodec: mark vdec_vp9_slice_map_counts_eob_coef noinline
media: dvb-frontends: dib3000mb: fix uninit-value in dib3000_write_reg
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI fixes from Krzysztof Wilczyński:
"Two small patches that are important for fixing boot time hang on
Intel JHL7540 'Titan Ridge' platforms equipped with a Thunderbolt
controller.
The boot time issue manifests itself when a PCI Express bandwidth
control is unnecessarily enabled on the Thunderbolt controller
downstream ports, which only supports a link speed of 2.5 GT/s in
accordance with USB4 v2 specification (p. 671, sec. 11.2.1, "PCIe
Physical Layer Logical Sub-block").
As such, there is no need to enable bandwidth control on such
downstream port links, which also works around the issue.
Both patches were tested by the original reporter on the hardware on
which the failure origin golly manifested itself. Both fixes were
proven to resolve the reported boot hang issue, and both patches have
been in linux-next this week with no reported problems"
* tag 'pci-v6.13-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci:
PCI/bwctrl: Enable only if more than one speed is supported
PCI: Honor Max Link Speed when determining supported speeds
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These fix some amd-pstate driver issues:
- Detect preferred core support in amd-pstate before driver
registration to avoid initialization ordering issues (K Prateek
Nayak)
- Fix issues with with boost numerator handling in amd-pstate leading
to inconsistently programmed CPPC max performance values (Mario
Limonciello)"
* tag 'pm-6.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq/amd-pstate: Use boost numerator for upper bound of frequencies
cpufreq/amd-pstate: Store the boost numerator as highest perf again
cpufreq/amd-pstate: Detect preferred core support before driver registration
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control fixes from Rafael Wysocki:
"Fix two issues with the user thermal thresholds feature introduced in
this development cycle (Daniel Lezcano)"
* tag 'thermal-6.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal/thresholds: Fix boundaries and detection routine
thermal/thresholds: Fix uapi header macros leading to a compilation error
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI fix from Rafael Wysocki:
"Unbreak ACPI EC support on LoongArch that has been broken earlier in
this development cycle (Huacai Chen)"
* tag 'acpi-6.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: EC: Enable EC support on LoongArch by default
|
|
Pull smb client fixes from Steve French:
- fix regression in display of write stats
- fix rmmod failure with network namespaces
- two minor cleanups
* tag '6.13-rc3-SMB3-client-fixes' of git://git.samba.org/sfrench/cifs-2.6:
smb: fix bytes written value in /proc/fs/cifs/Stats
smb: client: fix TCP timers deadlock after rmmod
smb: client: Deduplicate "select NETFS_SUPPORT" in Kconfig
smb: use macros instead of constants for leasekey size and default cifsattrs value
|
|
Pull NFS client fixes from Trond Myklebust:
- NFS/pnfs: Fix a live lock between recalled layouts and layoutget
- Fix a build warning about an undeclared symbol 'nfs_idmap_cache_timeout'
* tag 'nfs-for-6.13-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
fs/nfs: fix missing declaration of nfs_idmap_cache_timeout
NFS/pnfs: Fix a live lock between recalled layouts and layoutget
|
|
Pull ceph fixes from Ilya Dryomov:
"A handful of important CephFS fixes from Max, Alex and myself: memory
corruption due to a buffer overrun, potential infinite loop and
several memory leaks on the error paths. All but one marked for
stable"
* tag 'ceph-for-6.13-rc4' of https://github.com/ceph/ceph-client:
ceph: allocate sparse_ext map only for sparse reads
ceph: fix memory leak in ceph_direct_read_write()
ceph: improve error handling and short/overflow-read logic in __ceph_sync_read()
ceph: validate snapdirname option length when mounting
ceph: give up on paths longer than PATH_MAX
ceph: fix memory leaks in __ceph_sync_read()
|
|
Since commit 13b25489b6f8 ("kbuild: change working directory to external
module directory with M="), module paths are always relative to the top
of the external module tree.
The module paths recorded in Module.symvers are no longer globally unique
when they are passed via KBUILD_EXTRA_SYMBOLS for building other external
modules, which may result in false-positive "exported twice" errors.
Such errors should not occur because external modules should be able to
override in-tree modules.
To address this, record the dump file path in struct module and check it
when searching for a module.
Fixes: 13b25489b6f8 ("kbuild: change working directory to external module directory with M=")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Closes: https://lore.kernel.org/all/eb21a546-a19c-40df-b821-bbba80f19a3d@nvidia.com/
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
|
|
Stop installing Debian maintainer scripts when building a
user-mode-linux Debian package.
Debian maintainer scripts are used for e.g. requesting rebuilds of
initrd, rebuilding DKMS modules and updating of grub configuration. As
all of this is not relevant for UML but also may lead to failures while
processing the kernel hooks, do no more install maintainer scripts for
the UML package.
Suggested-by: Masahiro Yamada <masahiroy@kernel.org>
Signed-off-by: Nicolas Schier <nicolas@fjasle.eu>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
|
|
'make ARCH=um bindeb-pkg' shows the following warning.
$ make ARCH=um bindeb-pkg
[snip]
GEN debian
** ** ** WARNING ** ** **
Your architecture doesn't have its equivalent
Debian userspace architecture defined!
Falling back to the current host architecture (amd64).
Please add support for um to ./scripts/package/mkdebian ...
This commit hard-codes i386/amd64 because UML is only supported for x86.
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Reviewed-by: Nicolas Schier <nicolas@fjasle.eu>
|
