| Age | Commit message (Collapse) | Author |
|---|
|
When the driver is in switchdev mode and rx-gro-hw is set, the RQ needs
special CQE handling. Till then, block setting of rx-gro-hw feature in
switchdev mode, to avoid failure while setting the feature due to
failure while opening the RQ.
Fixes: f97d5c2a453e ("net/mlx5e: Add handle SHAMPO cqe support")
Signed-off-by: Aya Levin <ayal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
The body of mlx5e_napi_poll is wrapped into rcu_read_lock to be able to
read the XDP program pointer using rcu_dereference. However, the trap RQ
NAPI doesn't use rcu_read_lock, because the trap RQ works only in the
non-linear mode, and mlx5e_skb_from_cqe_nonlinear, until recently,
didn't support XDP and didn't call rcu_dereference.
Starting from the cited commit, mlx5e_skb_from_cqe_nonlinear supports
XDP and calls rcu_dereference, but mlx5e_trap_napi_poll doesn't wrap it
into rcu_read_lock. It leads to RCU-lockdep warnings like this:
WARNING: suspicious RCU usage
This commit fixes the issue by adding an rcu_read_lock to
mlx5e_trap_napi_poll, similarly to mlx5e_napi_poll.
Fixes: ea5d49bdae8b ("net/mlx5e: Add XDP multi buffer support to the non-linear legacy RQ")
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
When modifying TTL, packet's csum has to be recalculated.
Due to HW issue in ConnectX-5, csum recalculation for modify
TTL on RX is supported through a work-around that is specifically
enabled by configuration.
If the work-around isn't enabled, rather than adding an unsupported
action the modify TTL action on RX should be ignored.
Ignoring modify TTL action might result in zero actions, so in such
cases we will not convert the match STE to modify STE, as it is done
by FW in DMFS.
This patch fixes an issue where modify TTL action was ignored both
on RX and TX instead of only on RX.
Fixes: 4ff725e1d4ad ("net/mlx5: DR, Ignore modify TTL if device doesn't support it")
Signed-off-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Reviewed-by: Alex Vesker <valex@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
Currently, software objects of flow steering are created and destroyed
during reload flow. In case a device is unloaded, the following error
is printed during grace period:
mlx5_core 0000:00:0b.0: mlx5_fw_fatal_reporter_err_work:690:(pid 95):
Driver is in error state. Unloading
As a solution to fix use-after-free bugs, where we try to access
these objects, when reading the value of flow_steering_mode devlink
param[1], let's split flow steering creation and destruction into two
routines:
* init and cleanup: memory, cache, and pools allocation/free.
* create and destroy: namespaces initialization and cleanup.
While at it, re-order the cleanup function to mirror the init function.
[1]
Kasan trace:
[ 385.119849 ] BUG: KASAN: use-after-free in mlx5_devlink_fs_mode_get+0x3b/0xa0
[ 385.119849 ] Read of size 4 at addr ffff888104b79308 by task bash/291
[ 385.119849 ]
[ 385.119849 ] CPU: 1 PID: 291 Comm: bash Not tainted 5.17.0-rc1+ #2
[ 385.119849 ] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-2.fc32 04/01/2014
[ 385.119849 ] Call Trace:
[ 385.119849 ] <TASK>
[ 385.119849 ] dump_stack_lvl+0x6e/0x91
[ 385.119849 ] print_address_description.constprop.0+0x1f/0x160
[ 385.119849 ] ? mlx5_devlink_fs_mode_get+0x3b/0xa0
[ 385.119849 ] ? mlx5_devlink_fs_mode_get+0x3b/0xa0
[ 385.119849 ] kasan_report.cold+0x83/0xdf
[ 385.119849 ] ? devlink_param_notify+0x20/0x190
[ 385.119849 ] ? mlx5_devlink_fs_mode_get+0x3b/0xa0
[ 385.119849 ] mlx5_devlink_fs_mode_get+0x3b/0xa0
[ 385.119849 ] devlink_nl_param_fill+0x18a/0xa50
[ 385.119849 ] ? _raw_spin_lock_irqsave+0x8d/0xe0
[ 385.119849 ] ? devlink_flash_update_timeout_notify+0xf0/0xf0
[ 385.119849 ] ? __wake_up_common+0x4b/0x1e0
[ 385.119849 ] ? preempt_count_sub+0x14/0xc0
[ 385.119849 ] ? _raw_spin_unlock_irqrestore+0x28/0x40
[ 385.119849 ] ? __wake_up_common_lock+0xe3/0x140
[ 385.119849 ] ? __wake_up_common+0x1e0/0x1e0
[ 385.119849 ] ? __sanitizer_cov_trace_const_cmp8+0x27/0x80
[ 385.119849 ] ? __rcu_read_unlock+0x48/0x70
[ 385.119849 ] ? kasan_unpoison+0x23/0x50
[ 385.119849 ] ? __kasan_slab_alloc+0x2c/0x80
[ 385.119849 ] ? memset+0x20/0x40
[ 385.119849 ] ? __sanitizer_cov_trace_const_cmp4+0x25/0x80
[ 385.119849 ] devlink_param_notify+0xce/0x190
[ 385.119849 ] devlink_unregister+0x92/0x2b0
[ 385.119849 ] remove_one+0x41/0x140
[ 385.119849 ] pci_device_remove+0x68/0x140
[ 385.119849 ] ? pcibios_free_irq+0x10/0x10
[ 385.119849 ] __device_release_driver+0x294/0x3f0
[ 385.119849 ] device_driver_detach+0x82/0x130
[ 385.119849 ] unbind_store+0x193/0x1b0
[ 385.119849 ] ? subsys_interface_unregister+0x270/0x270
[ 385.119849 ] drv_attr_store+0x4e/0x70
[ 385.119849 ] ? drv_attr_show+0x60/0x60
[ 385.119849 ] sysfs_kf_write+0xa7/0xc0
[ 385.119849 ] kernfs_fop_write_iter+0x23a/0x2f0
[ 385.119849 ] ? sysfs_kf_bin_read+0x160/0x160
[ 385.119849 ] new_sync_write+0x311/0x430
[ 385.119849 ] ? new_sync_read+0x480/0x480
[ 385.119849 ] ? _raw_spin_lock+0x87/0xe0
[ 385.119849 ] ? __sanitizer_cov_trace_cmp4+0x25/0x80
[ 385.119849 ] ? security_file_permission+0x94/0xa0
[ 385.119849 ] vfs_write+0x4c7/0x590
[ 385.119849 ] ksys_write+0xf6/0x1e0
[ 385.119849 ] ? __x64_sys_read+0x50/0x50
[ 385.119849 ] ? fpregs_assert_state_consistent+0x99/0xa0
[ 385.119849 ] do_syscall_64+0x3d/0x90
[ 385.119849 ] entry_SYSCALL_64_after_hwframe+0x44/0xae
[ 385.119849 ] RIP: 0033:0x7fc36ef38504
[ 385.119849 ] Code: 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b3 0f 1f
80 00 00 00 00 48 8d 05 f9 61 0d 00 8b 00 85 c0 75 13 b8 01 00 00 00 0f
05 <48> 3d 00 f0 ff ff 77 54 c3 0f 1f 00 41 54 49 89 d4 55 48 89 f5 53
[ 385.119849 ] RSP: 002b:00007ffde0ff3d08 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 385.119849 ] RAX: ffffffffffffffda RBX: 000000000000000c RCX: 00007fc36ef38504
[ 385.119849 ] RDX: 000000000000000c RSI: 00007fc370521040 RDI: 0000000000000001
[ 385.119849 ] RBP: 00007fc370521040 R08: 00007fc36f00b8c0 R09: 00007fc36ee4b740
[ 385.119849 ] R10: 0000000000000000 R11: 0000000000000246 R12: 00007fc36f00a760
[ 385.119849 ] R13: 000000000000000c R14: 00007fc36f005760 R15: 000000000000000c
[ 385.119849 ] </TASK>
[ 385.119849 ]
[ 385.119849 ] Allocated by task 65:
[ 385.119849 ] kasan_save_stack+0x1e/0x40
[ 385.119849 ] __kasan_kmalloc+0x81/0xa0
[ 385.119849 ] mlx5_init_fs+0x11b/0x1160
[ 385.119849 ] mlx5_load+0x13c/0x220
[ 385.119849 ] mlx5_load_one+0xda/0x160
[ 385.119849 ] mlx5_recover_device+0xb8/0x100
[ 385.119849 ] mlx5_health_try_recover+0x2f9/0x3a1
[ 385.119849 ] devlink_health_reporter_recover+0x75/0x100
[ 385.119849 ] devlink_health_report+0x26c/0x4b0
[ 385.275909 ] mlx5_fw_fatal_reporter_err_work+0x11e/0x1b0
[ 385.275909 ] process_one_work+0x520/0x970
[ 385.275909 ] worker_thread+0x378/0x950
[ 385.275909 ] kthread+0x1bb/0x200
[ 385.275909 ] ret_from_fork+0x1f/0x30
[ 385.275909 ]
[ 385.275909 ] Freed by task 65:
[ 385.275909 ] kasan_save_stack+0x1e/0x40
[ 385.275909 ] kasan_set_track+0x21/0x30
[ 385.275909 ] kasan_set_free_info+0x20/0x30
[ 385.275909 ] __kasan_slab_free+0xfc/0x140
[ 385.275909 ] kfree+0xa5/0x3b0
[ 385.275909 ] mlx5_unload+0x2e/0xb0
[ 385.275909 ] mlx5_unload_one+0x86/0xb0
[ 385.275909 ] mlx5_fw_fatal_reporter_err_work.cold+0xca/0xcf
[ 385.275909 ] process_one_work+0x520/0x970
[ 385.275909 ] worker_thread+0x378/0x950
[ 385.275909 ] kthread+0x1bb/0x200
[ 385.275909 ] ret_from_fork+0x1f/0x30
[ 385.275909 ]
[ 385.275909 ] The buggy address belongs to the object at ffff888104b79300
[ 385.275909 ] which belongs to the cache kmalloc-128 of size 128
[ 385.275909 ] The buggy address is located 8 bytes inside of
[ 385.275909 ] 128-byte region [ffff888104b79300, ffff888104b79380)
[ 385.275909 ] The buggy address belongs to the page:
[ 385.275909 ] page:00000000de44dd39 refcount:1 mapcount:0 mapping:0000000000000000 index:0x0 pfn:0x104b78
[ 385.275909 ] head:00000000de44dd39 order:1 compound_mapcount:0
[ 385.275909 ] flags: 0x8000000000010200(slab|head|zone=2)
[ 385.275909 ] raw: 8000000000010200 0000000000000000 dead000000000122 ffff8881000428c0
[ 385.275909 ] raw: 0000000000000000 0000000080200020 00000001ffffffff 0000000000000000
[ 385.275909 ] page dumped because: kasan: bad access detected
[ 385.275909 ]
[ 385.275909 ] Memory state around the buggy address:
[ 385.275909 ] ffff888104b79200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 fc fc
[ 385.275909 ] ffff888104b79280: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 385.275909 ] >ffff888104b79300: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 385.275909 ] ^
[ 385.275909 ] ffff888104b79380: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc
[ 385.275909 ] ffff888104b79400: fa fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 385.275909 ]]
Fixes: e890acd5ff18 ("net/mlx5: Add devlink flow_steering_mode parameter")
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
In order to support multiple destination FTEs with SW steering
FW table is created with single FTE with multiple actions and
SW steering rule forward to it. When creating this table, flow
source isn't set according to the original FTE.
Fix this by passing the original FTE flow source to the created
FW table.
Fixes: 34583beea4b7 ("net/mlx5: DR, Create multi-destination table for SW-steering use")
Signed-off-by: Maor Dickman <maord@nvidia.com>
Reviewed-by: Yevgeny Kliteynik <kliteyn@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
|
|
There are sleep in atomic context bugs when the request to secure
element of st-nci is timeout. The root cause is that nci_skb_alloc
with GFP_KERNEL parameter is called in st_nci_se_wt_timeout which is
a timer handler. The call paths that could trigger bugs are shown below:
(interrupt context 1)
st_nci_se_wt_timeout
nci_hci_send_event
nci_hci_send_data
nci_skb_alloc(..., GFP_KERNEL) //may sleep
(interrupt context 2)
st_nci_se_wt_timeout
nci_hci_send_event
nci_hci_send_data
nci_send_data
nci_queue_tx_data_frags
nci_skb_alloc(..., GFP_KERNEL) //may sleep
This patch changes allocation mode of nci_skb_alloc from GFP_KERNEL to
GFP_ATOMIC in order to prevent atomic context sleeping. The GFP_ATOMIC
flag makes memory allocation operation could be used in atomic context.
Fixes: ed06aeefdac3 ("nfc: st-nci: Rename st21nfcb to st-nci")
Signed-off-by: Duoming Zhou <duoming@zju.edu.cn>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20220517012530.75714-1-duoming@zju.edu.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
test_bit() tests if one bit is set or not.
Here the logic seems to check of bit QL_RESET_PER_SCSI (i.e. 4) OR bit
QL_RESET_START (i.e. 3) is set.
In fact, it checks if bit 7 (4 | 3 = 7) is set, that is to say
QL_ADAPTER_UP.
This looks harmless, because this bit is likely be set, and when the
ql_reset_work() delayed work is scheduled in ql3xxx_isr() (the only place
that schedule this work), QL_RESET_START or QL_RESET_PER_SCSI is set.
This has been spotted by smatch.
Fixes: 5a4faa873782 ("[PATCH] qla3xxx NIC driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/80e73e33f390001d9c0140ffa9baddf6466a41a2.1652637337.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- Avoid putting Elo i2 PCIe Ports in D3cold because downstream devices
are inaccessible after going back to D0 (Rafael J. Wysocki)
- Qualcomm SM8250 has a ddrss_sf_tbu clock but SC8180X does not; make a
SC8180X-specific config without the clock so it probes correctly
(Bjorn Andersson)
- Revert aardvark chained IRQ handler rewrite because it broke
interrupt affinity (Pali Rohár)
* tag 'pci-v5.18-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
Revert "PCI: aardvark: Rewrite IRQ code to chained IRQ handler"
PCI: qcom: Remove ddrss_sf_tbu clock from SC8180X
PCI/PM: Avoid putting Elo i2 PCIe Ports in D3cold
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull thermal control fix from Rafael Wysocki:
"Fix up a recent change in the int340x thermal driver that
inadvertently broke thermal zone handling on some systems
(Srinivas Pandruvada)"
* tag 'thermal-5.18-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
thermal: int340x: Mode setting with new OS handshake
|
|
The code attempts to free the 'new' pointer using kmem_cache_free(),
which is wrong because this function isn't responsible of freeing it.
Instead, the function should free new->htable and clear the contents of
*new (to prevent double-free).
Cc: stable@vger.kernel.org
Fixes: c7c556f1e81b ("selinux: refactor changing booleans")
Reported-by: Wander Lairson Costa <wander@redhat.com>
Signed-off-by: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
This change fixes the following:
1) The flags variable is not initialized. Always use raw_spin_lock_irqsave
and raw_spin_unlock_irqrestore to serialize patching.
2) flush_kernel_vmap_range is primarily intended for DMA flushes.
The whole cache flush in flush_kernel_vmap_range is only possible
when interrupts are enabled on SMP machines. Since __patch_text_multiple
calls flush_kernel_vmap_range with interrupts disabled, it is better
to directly call flush_kernel_dcache_range_asm and
flush_kernel_icache_range_asm.
3) The final call to flush_icache_range is unnecessary.
Tested with `[PATCH, V3] parisc: Rewrite cache flush code for
PA8800/PA8900' change on rp3440, c8000 and c3750 (32 and 64-bit).
Note by Helge:
This patch had been temporarily reverted shortly before v5.18-rc6 in order
to fix boot issues. Now it can be re-applied.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Originally, I was convinced that we needed to use tmpalias flushes
everwhere, for both user and kernel flushes. However, when I modified
flush_kernel_dcache_page_addr, to use a tmpalias flush, my c8000
would crash quite early when booting.
The PDC returns alias values of 0 for the icache and dcache. This
indicates that either the alias boundary is greater than 16MB or
equivalent aliasing doesn't work. I modified the tmpalias code to
make it easy to try alternate boundaries. I tried boundaries up to
128MB but still kernel tmpalias flushes didn't work on c8000.
This led me to conclude that tmpalias flushes don't work on PA8800
and PA8900 machines, and that we needed to flush directly using the
virtual address of user and kernel pages. This is likely the major
cause of instability on the c8000 and rp34xx machines.
Flushing user pages requires doing a temporary context switch as we
have to flush pages that don't belong to the current context. Further,
we have to deal with pages that aren't present. If a page isn't
present, the flush instructions fault on every line.
Other code has been rearranged and simplified based on testing. For
example, I introduced a flush_cache_dup_mm routine. flush_cache_mm
and flush_cache_dup_mm differ in that flush_cache_mm calls
purge_cache_pages and flush_cache_dup_mm calls flush_cache_pages.
In some implementations, pdc is more efficient than fdc. Based on
my testing, I don't believe there's any performance benefit on the
c8000.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Change the "BUG" to "WARNING" and disable the message because it triggers
occasionally in spite of the check in flush_cache_page_if_present.
The pte value extracted for the "from" page in copy_user_highpage is racy and
occasionally the pte is cleared before the flush is complete. I assume that
the page is simultaneously flushed by flush_cache_mm before the pte is cleared
as nullifying the fdc doesn't seem to cause problems.
I investigated various locking scenarios but I wasn't able to find a way to
sequence the flushes. This code is called for every COW break and locks impact
performance.
This patch is related to the bigger cache flush patch because we need the pte
on PA8800/PA8900 to flush using the vma context.
I have also seen this from copy_to_user_page and copy_from_user_page.
The messages appear infrequently when enabled.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Not calling the function for dummy contexts will cause the context to
not be reset. During the next syscall, this will cause an error in
__audit_syscall_entry:
WARN_ON(context->context != AUDIT_CTX_UNUSED);
WARN_ON(context->name_count);
if (context->context != AUDIT_CTX_UNUSED || context->name_count) {
audit_panic("unrecoverable error in audit_syscall_entry()");
return;
}
These problematic dummy contexts are created via the following call
chain:
exit_to_user_mode_prepare
-> arch_do_signal_or_restart
-> get_signal
-> task_work_run
-> tctx_task_work
-> io_req_task_submit
-> io_issue_sqe
-> audit_uring_entry
Cc: stable@vger.kernel.org
Fixes: 5bd2182d58e9 ("audit,io_uring,io-wq: add some basic audit support to io_uring")
Signed-off-by: Julian Orth <ju.orth@gmail.com>
[PM: subject line tweaks]
Signed-off-by: Paul Moore <paul@paul-moore.com>
|
|
We gate whether to IOPOLL for a request on whether the opcode is allowed
on a ring setup for IOPOLL and if it's got a file assigned. MSG_RING
is the only one that allows a file yet isn't pollable, it's merely
supported to allow communication on an IOPOLL ring, not because we can
poll for completion of it.
Put the assigned file early and clear it, so we don't attempt to poll
for it.
Reported-by: syzbot+1a0a53300ce782f8b3ad@syzkaller.appspotmail.com
Fixes: 3f1d52abf098 ("io_uring: defer msg-ring file validity check until command issue")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Adaptive-rx and Adaptive-tx are interrupt moderation settings
that can be enabled/disabled using ethtool:
ethtool -C ethX adaptive-rx on/off adaptive-tx on/off
Unfortunately those settings are getting cleared after
changing number of queues, or in ethtool world 'channels':
ethtool -L ethX rx 1 tx 1
Clearing was happening due to introduction of bit fields
in ice_ring_container struct. This way only itr_setting
bits were rebuilt during ice_vsi_rebuild_set_coalesce().
Introduce an anonymous struct of bitfields and create a
union to refer to them as a single variable.
This way variable can be easily saved and restored.
Fixes: 61dc79ced7aa ("ice: Restore interrupt throttle settings after VSI rebuild")
Signed-off-by: Michal Wilczynski <michal.wilczynski@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The hardware statistics counters are not cleared during resets so the
drivers first access is to initialize the baseline and then subsequent
reads are for reporting the counters. The statistics counters are read
during the watchdog subtask when the interface is up. If the baseline
is not initialized before the interface is up, then there can be a brief
window in which some traffic can be transmitted/received before the
initial baseline reading takes place.
Directly initialize ethtool statistics in driver open so the baseline will
be initialized when the interface is up, and any dropped packets
incremented before the interface is up won't be reported.
Fixes: 28dc1b86f8ea9 ("ice: ignore dropped packets during init")
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Do not allow to write timestamps on RX rings if PF is being configured.
When PF is being configured RX rings can be freed or rebuilt. If at the
same time timestamps are updated, the kernel will crash by dereferencing
null RX ring pointer.
PID: 1449 TASK: ff187d28ed658040 CPU: 34 COMMAND: "ice-ptp-0000:51"
#0 [ff1966a94a713bb0] machine_kexec at ffffffff9d05a0be
#1 [ff1966a94a713c08] __crash_kexec at ffffffff9d192e9d
#2 [ff1966a94a713cd0] crash_kexec at ffffffff9d1941bd
#3 [ff1966a94a713ce8] oops_end at ffffffff9d01bd54
#4 [ff1966a94a713d08] no_context at ffffffff9d06bda4
#5 [ff1966a94a713d60] __bad_area_nosemaphore at ffffffff9d06c10c
#6 [ff1966a94a713da8] do_page_fault at ffffffff9d06cae4
#7 [ff1966a94a713de0] page_fault at ffffffff9da0107e
[exception RIP: ice_ptp_update_cached_phctime+91]
RIP: ffffffffc076db8b RSP: ff1966a94a713e98 RFLAGS: 00010246
RAX: 16e3db9c6b7ccae4 RBX: ff187d269dd3c180 RCX: ff187d269cd4d018
RDX: 0000000000000000 RSI: 0000000000000000 RDI: 0000000000000000
RBP: ff187d269cfcc644 R8: ff187d339b9641b0 R9: 0000000000000000
R10: 0000000000000002 R11: 0000000000000000 R12: ff187d269cfcc648
R13: ffffffff9f128784 R14: ffffffff9d101b70 R15: ff187d269cfcc640
ORIG_RAX: ffffffffffffffff CS: 0010 SS: 0018
#8 [ff1966a94a713ea0] ice_ptp_periodic_work at ffffffffc076dbef [ice]
#9 [ff1966a94a713ee0] kthread_worker_fn at ffffffff9d101c1b
#10 [ff1966a94a713f10] kthread at ffffffff9d101b4d
#11 [ff1966a94a713f50] ret_from_fork at ffffffff9da0023f
Fixes: 77a781155a65 ("ice: enable receive hardware timestamping")
Signed-off-by: Arkadiusz Kubalewski <arkadiusz.kubalewski@intel.com>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Dave Cain <dcain@redhat.com>
Tested-by: Gurucharan <gurucharanx.g@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In vmxnet3_rq_create(), when dma_alloc_coherent() fails,
vmxnet3_rq_destroy() is called. It sets rq->rx_ring[i].base to NULL. Then
vmxnet3_rq_create() returns an error to its callers mxnet3_rq_create_all()
-> vmxnet3_change_mtu(). Then vmxnet3_change_mtu() calls
vmxnet3_force_close() -> dev_close() in error handling code. And the driver
calls vmxnet3_close() -> vmxnet3_quiesce_dev() -> vmxnet3_rq_cleanup_all()
-> vmxnet3_rq_cleanup(). In vmxnet3_rq_cleanup(),
rq->rx_ring[ring_idx].base is accessed, but this variable is NULL, causing
a NULL pointer dereference.
To fix this possible bug, an if statement is added to check whether
rq->rx_ring[0].base is NULL in vmxnet3_rq_cleanup() and exit early if so.
The error log in our fault-injection testing is shown as follows:
[ 65.220135] BUG: kernel NULL pointer dereference, address: 0000000000000008
...
[ 65.222633] RIP: 0010:vmxnet3_rq_cleanup_all+0x396/0x4e0 [vmxnet3]
...
[ 65.227977] Call Trace:
...
[ 65.228262] vmxnet3_quiesce_dev+0x80f/0x8a0 [vmxnet3]
[ 65.228580] vmxnet3_close+0x2c4/0x3f0 [vmxnet3]
[ 65.228866] __dev_close_many+0x288/0x350
[ 65.229607] dev_close_many+0xa4/0x480
[ 65.231124] dev_close+0x138/0x230
[ 65.231933] vmxnet3_force_close+0x1f0/0x240 [vmxnet3]
[ 65.232248] vmxnet3_change_mtu+0x75d/0x920 [vmxnet3]
...
Fixes: d1a890fa37f27 ("net: VMware virtual Ethernet NIC driver: vmxnet3")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Zixuan Fu <r33s3n6@gmail.com>
Link: https://lore.kernel.org/r/20220514050711.2636709-1-r33s3n6@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In vmxnet3_rq_alloc_rx_buf(), when dma_map_single() fails, rbi->skb is
freed immediately. Similarly, in another branch, when dma_map_page() fails,
rbi->page is also freed. In the two cases, vmxnet3_rq_alloc_rx_buf()
returns an error to its callers vmxnet3_rq_init() -> vmxnet3_rq_init_all()
-> vmxnet3_activate_dev(). Then vmxnet3_activate_dev() calls
vmxnet3_rq_cleanup_all() in error handling code, and rbi->skb or rbi->page
are freed again in vmxnet3_rq_cleanup_all(), causing use-after-free bugs.
To fix these possible bugs, rbi->skb and rbi->page should be cleared after
they are freed.
The error log in our fault-injection testing is shown as follows:
[ 14.319016] BUG: KASAN: use-after-free in consume_skb+0x2f/0x150
...
[ 14.321586] Call Trace:
...
[ 14.325357] consume_skb+0x2f/0x150
[ 14.325671] vmxnet3_rq_cleanup_all+0x33a/0x4e0 [vmxnet3]
[ 14.326150] vmxnet3_activate_dev+0xb9d/0x2ca0 [vmxnet3]
[ 14.326616] vmxnet3_open+0x387/0x470 [vmxnet3]
...
[ 14.361675] Allocated by task 351:
...
[ 14.362688] __netdev_alloc_skb+0x1b3/0x6f0
[ 14.362960] vmxnet3_rq_alloc_rx_buf+0x1b0/0x8d0 [vmxnet3]
[ 14.363317] vmxnet3_activate_dev+0x3e3/0x2ca0 [vmxnet3]
[ 14.363661] vmxnet3_open+0x387/0x470 [vmxnet3]
...
[ 14.367309]
[ 14.367412] Freed by task 351:
...
[ 14.368932] __dev_kfree_skb_any+0xd2/0xe0
[ 14.369193] vmxnet3_rq_alloc_rx_buf+0x71e/0x8d0 [vmxnet3]
[ 14.369544] vmxnet3_activate_dev+0x3e3/0x2ca0 [vmxnet3]
[ 14.369883] vmxnet3_open+0x387/0x470 [vmxnet3]
[ 14.370174] __dev_open+0x28a/0x420
[ 14.370399] __dev_change_flags+0x192/0x590
[ 14.370667] dev_change_flags+0x7a/0x180
[ 14.370919] do_setlink+0xb28/0x3570
[ 14.371150] rtnl_newlink+0x1160/0x1740
[ 14.371399] rtnetlink_rcv_msg+0x5bf/0xa50
[ 14.371661] netlink_rcv_skb+0x1cd/0x3e0
[ 14.371913] netlink_unicast+0x5dc/0x840
[ 14.372169] netlink_sendmsg+0x856/0xc40
[ 14.372420] ____sys_sendmsg+0x8a7/0x8d0
[ 14.372673] __sys_sendmsg+0x1c2/0x270
[ 14.372914] do_syscall_64+0x41/0x90
[ 14.373145] entry_SYSCALL_64_after_hwframe+0x44/0xae
...
Fixes: 5738a09d58d5a ("vmxnet3: fix checks for dma mapping errors")
Reported-by: TOTE Robot <oslab@tsinghua.edu.cn>
Signed-off-by: Zixuan Fu <r33s3n6@gmail.com>
Link: https://lore.kernel.org/r/20220514050656.2636588-1-r33s3n6@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The global blackhole_netdev has replaced pernet loopback_dev to become the
one given to the object that holds an netdev when ifdown in many places of
ipv4 and ipv6 since commit 8d7017fd621d ("blackhole_netdev: use
blackhole_netdev to invalidate dst entries").
Especially after commit faab39f63c1f ("net: allow out-of-order netdev
unregistration"), it's no longer safe to use loopback_dev that may be
freed before other netdev.
This patch is to set dst dev to blackhole_netdev instead of loopback_dev
in ifdown.
v1->v2:
- add Fixes tag as Eric suggested.
Fixes: faab39f63c1f ("net: allow out-of-order netdev unregistration")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/e8c87482998ca6fcdab214f5a9d582899ec0c648.1652665047.git.lucien.xin@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
if devm_clk_get_optional() fails, we still need to go through the error
handling path.
Add the missing goto.
Fixes: 6328a126896ea ("net: systemport: Manage Wake-on-LAN clock")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/99d70634a81c229885ae9e4ee69b2035749f7edc.1652634040.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The following two scenarios were failing for lan966x.
1. If the port had the address X and then trying to assign the same
address, then the HW was just removing this address because first it
tries to learn new address and then delete the old one. As they are
the same the HW remove it.
2. If the port eth0 was assigned the same address as one of the other
ports eth1 then when assigning back the address to eth0 then the HW
was deleting the address of eth1.
The case 1. is fixed by checking if the port has already the same
address while case 2. is fixed by checking if the address is used by any
other port.
Fixes: e18aba8941b40b ("net: lan966x: add mactable support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Link: https://lore.kernel.org/r/20220513180030.3076793-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
This reverts commit 1571d67dc190e50c6c56e8f88cdc39f7cc53166e.
This commit broke support for setting interrupt affinity. It looks like
that it is related to the chained IRQ handler. Revert this commit until
issue with setting interrupt affinity is fixed.
Fixes: 1571d67dc190 ("PCI: aardvark: Rewrite IRQ code to chained IRQ handler")
Link: https://lore.kernel.org/r/20220515125815.30157-1-pali@kernel.org
Signed-off-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
delta_ns is a s64, but it was being passed ptp_ocp_adjtime_coarse
as an u64. Also, it turns out that timespec64_add_ns() only handles
positive values, so perform the math with set_normalized_timespec().
Fixes: 90f8f4c0e3ce ("ptp: ocp: Add ptp_ocp_adjtime_coarse for large adjustments")
Suggested-by: Vadim Fedorenko <vfedorenko@novek.ru>
Signed-off-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Acked-by: Vadim Fedorenko <vfedorenko@novek.ru>
Link: https://lore.kernel.org/r/20220513225231.1412-1-jonathan.lemon@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When running a combination of PPPoE on top of a VLAN, we need to set
info->outdev to the PPPoE device, otherwise PPPoE encap is skipped
during software offload.
Fixes: 72efd585f714 ("netfilter: flowtable: add pppoe support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
When calling dev_fill_forward_path on a pppoe device, the provided destination
address is invalid. In order for the bridge fdb lookup to succeed, the pppoe
code needs to update ctx->daddr to the correct value.
Fix this by storing the address inside struct net_device_path_ctx
Fixes: f6efc675c9dd ("net: ppp: resolve forwarding path for bridge pppoe devices")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
The dst entry does not contain a valid hardware address, so skip the lookup
in order to avoid running into errors here.
The proper hardware address is filled in from nft_dev_path_info
Fixes: 72efd585f714 ("netfilter: flowtable: add pppoe support")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
If a flow cannot be offloaded, the code currently repeatedly tries again as
quickly as possible, which can significantly increase system load.
Fix this by limiting flow timeout update and hardware offload retry to once
per second.
Fixes: c07531c01d82 ("netfilter: flowtable: Remove redundant hw refresh bit")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
syzbot was able to trigger an Out-of-Bound on the pedit action:
UBSAN: shift-out-of-bounds in net/sched/act_pedit.c:238:43
shift exponent 1400735974 is too large for 32-bit type 'unsigned int'
CPU: 0 PID: 3606 Comm: syz-executor151 Not tainted 5.18.0-rc5-syzkaller-00165-g810c2f0a3f86 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
<TASK>
__dump_stack lib/dump_stack.c:88 [inline]
dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106
ubsan_epilogue+0xb/0x50 lib/ubsan.c:151
__ubsan_handle_shift_out_of_bounds.cold+0xb1/0x187 lib/ubsan.c:322
tcf_pedit_init.cold+0x1a/0x1f net/sched/act_pedit.c:238
tcf_action_init_1+0x414/0x690 net/sched/act_api.c:1367
tcf_action_init+0x530/0x8d0 net/sched/act_api.c:1432
tcf_action_add+0xf9/0x480 net/sched/act_api.c:1956
tc_ctl_action+0x346/0x470 net/sched/act_api.c:2015
rtnetlink_rcv_msg+0x413/0xb80 net/core/rtnetlink.c:5993
netlink_rcv_skb+0x153/0x420 net/netlink/af_netlink.c:2502
netlink_unicast_kernel net/netlink/af_netlink.c:1319 [inline]
netlink_unicast+0x543/0x7f0 net/netlink/af_netlink.c:1345
netlink_sendmsg+0x904/0xe00 net/netlink/af_netlink.c:1921
sock_sendmsg_nosec net/socket.c:705 [inline]
sock_sendmsg+0xcf/0x120 net/socket.c:725
____sys_sendmsg+0x6e2/0x800 net/socket.c:2413
___sys_sendmsg+0xf3/0x170 net/socket.c:2467
__sys_sendmsg+0xe5/0x1b0 net/socket.c:2496
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x35/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x44/0xae
RIP: 0033:0x7fe36e9e1b59
Code: 28 c3 e8 2a 14 00 00 66 2e 0f 1f 84 00 00 00 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 c0 ff ff ff f7 d8 64 89 01 48
RSP: 002b:00007ffef796fe88 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 0000000000000000 RCX: 00007fe36e9e1b59
RDX: 0000000000000000 RSI: 0000000020000300 RDI: 0000000000000003
RBP: 00007fe36e9a5d00 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00007fe36e9a5d90
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
</TASK>
The 'shift' field is not validated, and any value above 31 will
trigger out-of-bounds. The issue predates the git history, but
syzbot was able to trigger it only after the commit mentioned in
the fixes tag, and this change only applies on top of such commit.
Address the issue bounding the 'shift' value to the maximum allowed
by the relevant operator.
Reported-and-tested-by: syzbot+8ed8fc4c57e9dcf23ca6@syzkaller.appspotmail.com
Fixes: 8b796475fd78 ("net/sched: act_pedit: really ensure the skb is writable")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At cleaning up and moving the device rename from the quirk table to
its own table, we removed the entry for Rane SL-1 as we thought it's
only for renaming. It turned out, however, that the quirk is required
for matching with the device that declares itself as no standard
audio but only as vendor-specific.
Restore the quirk entry for Rane SL-1 to fix the regression.
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=215887
Fixes: 5436f59bc5bc ("ALSA: usb-audio: Move device rename and profile quirks to an internal table")
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220516103112.12950-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2022-05-14
this is a pull request of 2 patches for net/master.
Changes to linux-can-fixes-for-5.18-20220513:
- adjusted Fixes: Tag on "Revert "can: m_can: pci: use custom bit timings for Elkhart Lake""
(Thanks Jakub)
Both patches are by Jarkko Nikula, target the m_can PCI driver
bindings, and fix usage of wrong bit timing constants for the Elkhart
Lake platform.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The HP EliteBook 630 is using ALC236 codec which used 0x02 to control mute LED
and 0x01 to control micmute LED. Therefore, add a quirk to make it works.
Signed-off-by: Andy Chi <andy.chi@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20220513121648.28584-1-andy.chi@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
In IPv4 setting the "disable_policy" flag on a device means no policy
should be enforced for traffic originating from the device. This was
implemented by seting the DST_NOPOLICY flag in the dst based on the
originating device.
However, dsts are cached in nexthops regardless of the originating
devices, in which case, the DST_NOPOLICY flag value may be incorrect.
Consider the following setup:
+------------------------------+
| ROUTER |
+-------------+ | +-----------------+ |
| ipsec src |----|-|ipsec0 | |
+-------------+ | |disable_policy=0 | +----+ |
| +-----------------+ |eth1|-|-----
+-------------+ | +-----------------+ +----+ |
| noipsec src |----|-|eth0 | |
+-------------+ | |disable_policy=1 | |
| +-----------------+ |
+------------------------------+
Where ROUTER has a default route towards eth1.
dst entries for traffic arriving from eth0 would have DST_NOPOLICY
and would be cached and therefore can be reused by traffic originating
from ipsec0, skipping policy check.
Fix by setting a IPSKB_NOPOLICY flag in IPCB and observing it instead
of the DST in IN/FWD IPv4 policy checks.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Reported-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Eyal Birger <eyal.birger@gmail.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
|
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg KH:
"Here is one fix, and three documentation updates for 5.18-rc7.
The fix is for the firmware loader which resolves a long-reported
problem where the credentials of the firmware loader could be set to a
userspace process without enough permissions to actually load the
firmware image. Many Android vendors have been reporting this for
quite some time.
The documentation updates are for the embargoed-hardware-issues.rst
file to add a new entry, change an existing one, and sort the list to
make changes easier in the future.
All of these have been in linux-next for a while with no reported
issues"
* tag 'driver-core-5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
Documentation/process: Update ARM contact for embargoed hardware issues
Documentation/process: Add embargoed HW contact for Ampere Computing
Documentation/process: Make groups alphabetical and use tabs consistently
firmware_loader: use kernel credentials when reading firmware
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are two small driver fixes for 5.18-rc7 that resolve reported
problems:
- slimbus driver irq bugfix
- interconnect sync state bugfix
Both of these have been in linux-next with no reported problems"
* tag 'char-misc-5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
slimbus: qcom: Fix IRQ check in qcom_slim_probe
interconnect: Restore sync state by ignoring ipa-virt in provider count
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver fixes from Greg KH:
"Here are some small tty n_gsm and serial driver fixes for 5.18-rc7
that resolve reported problems. They include:
- n_gsm fixes for reported issues
- 8250_mtk driver fixes for some platforms
- fsl_lpuart driver fix for reported problem.
- digicolor driver fix for reported problem.
All have been in linux-next for a while with no reported problems"
* tag 'tty-5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
fsl_lpuart: Don't enable interrupts too early
tty: n_gsm: fix invalid gsmtty_write_room() result
tty: n_gsm: fix mux activation issues in gsm_config()
tty: n_gsm: fix buffer over-read in gsm_dlci_data()
serial: 8250_mtk: Fix register address for XON/XOFF character
serial: 8250_mtk: Make sure to select the right FEATURE_SEL
serial: 8250_mtk: Fix UART_EFR register address
tty/serial: digicolor: fix possible null-ptr-deref in digicolor_uart_probe()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small fixes for reported issues with some USB drivers.
They include:
- xhci fixes for xhci-mtk platform driver
- typec driver fixes for reported problems.
- cdc-wdm read-stuck fix
- gadget driver fix for reported race condition
- new usb-serial driver ids
All of these have been in linux-next with no reported problems"
* tag 'usb-5.18-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: xhci-mtk: remove bandwidth budget table
usb: xhci-mtk: fix fs isoc's transfer error
usb: gadget: fix race when gadget driver register via ioctl
usb: typec: tcpci_mt6360: Update for BMC PHY setting
usb: gadget: uvc: allow for application to cleanly shutdown
usb: typec: tcpci: Don't skip cleanup in .remove() on error
usb: cdc-wdm: fix reading stuck on device close
USB: serial: qcserial: add support for Sierra Wireless EM7590
USB: serial: option: add Fibocom MA510 modem
USB: serial: option: add Fibocom L610 modem
USB: serial: pl2303: add device id for HP LM930 Display
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fix from Michael Ellerman:
- Fix KVM PR on 32-bit, which was broken by some MMU code refactoring.
Thanks to: Alexander Graf, and Matt Evans.
* tag 'powerpc-5.18-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
KVM: PPC: Book3S PR: Enable MSR_DR for switch_mmu_context()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fix from Thomas Gleixner:
"A single fix for the handling of unpopulated sub-pmd spaces.
The copy & pasta from the corresponding s390 code screwed up the
address calculation for marking the sub-pmd ranges via memset by
omitting the ALIGN_DOWN() to calculate the proper start address.
It's a mystery why this code is not generic and shared because there
is nothing architecture specific in there, but that's too intrusive
for a backportable fix"
* tag 'x86-urgent-2022-05-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/mm: Fix marking of unused sub-pmd ranges
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler fix from Thomas Gleixner:
"The recent expansion of the sched switch tracepoint inserted a new
argument in the middle of the arguments. This reordering broke BPF
programs which relied on the old argument list.
While tracepoints are not considered stable ABI, it's not trivial to
make BPF cope with such a change, but it's being worked on. For now
restore the original argument order and move the new argument to the
end of the argument list"
* tag 'sched-urgent-2022-05-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
sched/tracing: Append prev_state to tp args instead
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Thomas Gleixner:
"A single fix for a recent (introduced in 5.16) regression in the core
interrupt code.
The consolidation of the interrupt handler invocation code added an
unconditional warning when generic_handle_domain_irq() is invoked from
outside hard interrupt context. That's overbroad as the requirement
for invoking these handlers in hard interrupt context is only required
for certain interrupt types. The subsequently called code already
contains a warning which triggers conditionally for interrupt chips
which indicate this requirement in their properties.
Remove the overbroad one"
* tag 'irq-urgent-2022-05-15' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Remove WARN_ON_ONCE() in generic_handle_domain_irq()
|
|
Now when Intel Elkhart Lake uses again common bit timing and there are
no other users for custom bit timing, we can bring back the changes
done by the commit 0ddd83fbebbc ("can: m_can: remove support for
custom bit timing").
This effectively reverts commit ea768b2ffec6 ("Revert "can: m_can:
remove support for custom bit timing"") while taking into account
commit ea22ba40debe ("can: m_can: make custom bittiming fields const")
and commit 7d4a101c0bd3 ("can: dev: add sanity check in
can_set_static_ctrlmode()").
Link: https://lore.kernel.org/all/20220512124144.536850-2-jarkko.nikula@linux.intel.com
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This reverts commit 0e8ffdf3b86dfd44b651f91b12fcae76c25c453b.
Commit 0e8ffdf3b86d ("can: m_can: pci: use custom bit timings for
Elkhart Lake") broke the test case using bitrate switching.
| ip link set can0 up type can bitrate 500000 dbitrate 4000000 fd on
| ip link set can1 up type can bitrate 500000 dbitrate 4000000 fd on
| candump can0 &
| cangen can1 -I 0x800 -L 64 -e -fb \
| -D 11223344deadbeef55667788feedf00daabbccdd44332211 -n 1 -v -v
Above commit does everything correctly according to the datasheet.
However datasheet wasn't correct.
I got confirmation from hardware engineers that the actual CAN
hardware on Intel Elkhart Lake is based on M_CAN version v3.2.0.
Datasheet was mirroring values from an another specification which was
based on earlier M_CAN version leading to wrong bit timings.
Therefore revert the commit and switch back to common bit timings.
Fixes: ea4c1787685d ("can: m_can: pci: use custom bit timings for Elkhart Lake")
Link: https://lore.kernel.org/all/20220512124144.536850-1-jarkko.nikula@linux.intel.com
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reported-by: Chee Hou Ong <chee.houx.ong@intel.com>
Reported-by: Aman Kumar <aman.kumar@intel.com>
Reported-by: Pallavi Kumari <kumari.pallavi@intel.com>
Cc: <stable@vger.kernel.org> # v5.16+
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux
Pull perf tools fixes from Arnaldo Carvalho de Melo:
- Fix two NDEBUG warnings in 'perf bench numa'
- Fix ARM coresight `perf test` failure
- Sync linux/kvm.h with the kernel sources
- Add James and Mike as Arm64 performance events reviewers
* tag 'perf-tools-fixes-for-v5.18-2022-05-14' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux:
MAINTAINERS: Add James and Mike as Arm64 performance events reviewers
tools headers UAPI: Sync linux/kvm.h with the kernel sources
perf tests: Fix coresight `perf test` failure.
perf bench: Fix two numa NDEBUG warnings
|
|
In gem_rx_refill rx_prepared_head is incremented at the beginning of
the while loop preparing the skb and data buffers. If the skb or data
buffer allocation fails, this BD will be unusable BDs until the head
loops back to the same BD (and obviously buffer allocation succeeds).
In the unlikely event that there's a string of allocation failures,
there will be an equal number of unusable BDs and an inconsistent RX
BD chain. Hence increment the head at the end of the while loop to be
clean.
Fixes: 4df95131ea80 ("net/macb: change RX path for GEM")
Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@xilinx.com>
Reviewed-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Link: https://lore.kernel.org/r/20220512171900.32593-1-harini.katakam@xilinx.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Mat Martineau says:
====================
mptcp: Subflow accounting fix
This series contains a bug fix affecting the in-kernel path manager
(patch 1), where closing subflows would sometimes not adjust the PM's
count of active subflows. Patch 2 updates the selftests to exercise the
new code.
====================
Link: https://lore.kernel.org/r/20220512232642.541301-1-mathew.j.martineau@linux.intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add and delete a bunch of endpoints and verify the
respect of configured limits.
This covers the codepath introduced by the previous patch.
Fixes: 69c6ce7b6eca ("selftests: mptcp: add implicit endpoint test case")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the PM closes a fully established MPJ subflow or the subflow
creation errors out in it's early stage the subflows counter is
not bumped accordingly.
This change adds the missing accounting, additionally taking care
of updating accordingly the 'accept_subflow' flag.
Fixes: a88c9e496937 ("mptcp: do not block subflows creation on errors")
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
