| Age | Commit message (Collapse) | Author |
|---|
|
All devices are capable of using regular DSA tags. Support for
Ethertyped DSA tags sort into three categories:
1. No support. Older chips fall into this category.
2. Full support. Datasheet explicitly supports configuring the CPU
port to receive FORWARDs with a DSA tag.
3. Undocumented support. Datasheet lists the configuration from
category 2 as "reserved for future use", but does empirically
behave like a category 2 device.
So, instead of listing the one true protocol that should be used by a
particular chip, specify the level of support for EDSA (support for
regular DSA is implicit on all chips). As before, we use EDSA for all
chips that fully supports it.
In upcoming changes, we will use this information to support
dynamically changing the tag protocol.
Signed-off-by: Tobias Waldekranz <tobias@waldekranz.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211-next
Johannes Berg says:
====================
Another set of updates, all over the map:
* set sk_pacing_shift for 802.3->802.11 encap offload
* some monitor support for 802.11->802.3 decap offload
* HE (802.11ax) spec updates
* userspace API for TDLS HE support
* along with various other small features, cleanups and
fixups
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Petr Machata says:
====================
mlxsw: Refactor qdisc offload
Currently, mlxsw admits for offload a suitable root qdisc, and its
children. Thus up to two levels of hierarchy are offloaded. Often, this is
enough: one can configure TCs with RED and TCs with a shaper, and can even
see counters for each TC by looking at a qdisc at a sufficiently shallow
position.
While simple, the system has obvious shortcomings. It is not possible to
configure both RED and shaping on one TC. It is not possible to place a
PRIO below root TBF, which would then be offloaded as port shaper. FIFOs
are only offloaded at root or directly below, which is confusing to users,
because RED and TBF of course have their own FIFO.
This patchset is a step towards the end goal of allowing more comprehensive
qdisc tree offload and cleans up the qdisc offload code.
- Patches #1-#4 contain small cleanups.
- Up until now, since mlxsw offloaded only a very simple qdisc
configurations, basically all bookkeeping was done using one container
for the root qdisc, and 8 containers for its children. Patches #5, #6, #8
and #9 gradually introduce a more dynamic structure, where parent-child
relationships are tracked directly at qdiscs, instead of being implicit.
- This tree management assumes only one qdisc is created at a time. In FIFO
handlers, this condition was enforced simply by asserting RTNL lock. But
instead of furthering this RTNL dependence, patch #7 converts the whole
qdisc offload logic to a per-port mutex.
- Patch #10 adds a selftest.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There was a bug introduced during the rework which cause non-zero backlog
being stuck at ETS. Introduce a selftest that would have caught the issue
earlier.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlxsw used to hold an array of qdiscs indexed by the TC number. In the
previous patch, it was changed to allocate child qdiscs dynamically, and
they are now indexed by band number. Follow suit with the array of future
FIFOs.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of keeping qdiscs in globally-preallocated arrays, introduce a
per-qdisc-kind value num_classes, and then allocate the necessary child
qdiscs (if any) based on that value. Since now dynamic allocation is
involved, mlxsw_sp_qdisc_replace() gets messy enough that it is worth it to
split it to two cases: a new qdisc allocation and a change of existing
qdisc. (Note that the change also includes what TC formally calls replace,
if the qdisc kind is the same.)
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The FIFO handler currently guards accesses to the future FIFO tracking by
asserting RTNL. In the future, the changes to the qdisc state will be more
thorough, so other qdiscs will need this guarding is as well. In order
to not further the RTNL infestation, instead convert to a custom lock that
will guard accesses to the qdisc state.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mlxsw currently allows a two-level structure of qdiscs: the root and
possibly a number of children. In order to support offloading more general
qdisc trees, introduce to struct mlxsw_sp_qdisc a pointer to child qdiscs.
Refer to the child qdiscs through this pointer, instead of going through
the tclass_qdiscs in qdisc_state. Additionally introduce a field
num_classes, which holds number of given qdisc's children.
Also introduce a generic function for walking qdisc trees. Rewrite
mlxsw_sp_qdisc_find() and _find_by_handle() to use the generic walker.
For now, keep the qdisc_state.tclass_qdisc, and just point root_qdiscs's
children to this array. Following patches will make the allocation dynamic.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a qdisc is removed, it is necessary to update the backlog value at its
parent--unless the qdisc is at root position. RED, TBF and FIFO all do
that, each separately. Since all of them need to do this, just promote the
operation directly to mlxsw_sp_qdisc_destroy(), instead of deferring it to
individual destructors. Since FIFO dtor thus becomes trivial, remove it.
Add struct mlxsw_sp_qdisc.parent to point at the parent qdisc. This will be
handy later as deeper structures are offloaded. Use the parent qdisc to
find the chain of parents whose backlog value needs to be updated.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tclass_num is just a number, a value that would be ordinarily passed around
as an int. (Which is unlike a u8 prio_bitmap.) In several places,
tclass_num already is an int. Convert the remaining instances.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function mlxsw_sp_qdisc_compare() is invoked a couple lines above this
check, which will bounce any requests where this condition does not hold.
Therefore drop it.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The purpose of this function is to filter out events that are related to
qdiscs that are not offloaded, or are not offloaded anymore. But the
function is unnecessarily thorough:
- mlxsw_sp_qdisc pointer is never NULL in the context where it is called
- Two qdiscs with the same handle will never have different types. Even
when replacing one qdisc with another in the same class, Linux will not
permit handle reuse unless the qdisc type also matches.
Simplify the function by omitting these two unnecessary conditions.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mlxsw_sp_qdisc argument is not used in any of the actual callbacks.
Drop it.
Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marek Behún says:
====================
net: phy: marvell: some HWMON updates
Here are some updates for Marvell PHY HWMON, mainly
- refactoring for code deduplication
- Amethyst PHY support
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for Amethyst internal PHY.
The only difference from Peridot is HWMON.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Amethyst internal PHYs also report empty model number in MII_PHYSID2.
Fill in switch product number, as is done for Topaz and Peridot.
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the &= operator instead of
ret = ret & ...
Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Register 27_6.15:14 has the following description in 88E6393X
documentation:
Temperature Sensor Enable
0x0 - Sample every 1s
0x1 - Sense rate decided by bits 10:8 of this register
0x2 - Use 26_6.5 (One shot Temperature Sample) to enable
0x3 - Disable
This is compatible with how the 6390 code uses this register currently,
but the 6390 code handles it as two 1-bit registers (somewhat), instead
of one register with 4 possible values.
(A newer version of the 6390 documentation removed temperature sensor
section completely. In an older version, the above mentioned register
is reserved, although it is R/W. Since the code works, I think we can
assume that it is correct.)
Rename this register and define all 4 values according to 6393X
documentation.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use a structure of Marvell PHY specific HWMON methods to reduce code
duplication. Store a pointer to this structure into the PHY driver's
driver_data member.
Signed-off-by: Marek Behún <kabel@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2021-04-19
This patchset provides some updates to mlx5e and mlx5 SW steering drivers:
1) Tariq and Vladyslav they both provide some trivial update to mlx5e netdev.
The next 12 patches in the patchset are focused toward mlx5 SW steering:
2) 3 trivial cleanup patches
3) Dynamic Flex parser support:
Flex parser is a HW parser that can support protocols that are not
natively supported by the HCA, such as Geneve (TLV options) and GTP-U.
There are 8 such parsers, and each of them can be assigned to parse a
specific set of protocols.
4) Enable matching on Geneve TLV options
5) Use Flex parser for MPLS over UDP/GRE
6) Enable matching on tunnel GTP-U and GTP-U first extension
header using
7) Improved QoS for SW steering internal QPair for a better insertion rate
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ALWAYS_GUARD_BAND_SCH_Q bit in TAS config register is descripted as
this:
0: Guard band is implemented for nonschedule queues to schedule
queues transition.
1: Guard band is implemented for any queue to schedule queue
transition.
The driver set guard band be implemented for any queue to schedule queue
transition before, which will make each GCL time slot reserve a guard
band time that can pass the max SDU frame. Because guard band time could
not be set in tc-taprio now, it will use about 12000ns to pass 1500B max
SDU. This limits each GCL time interval to be more than 12000ns.
This patch change the guard band to be only implemented for nonschedule
queues to schedule queues transition, so that there is no need to reserve
guard band on each GCL. Users can manually add guard band time for each
schedule queues in their configuration if they want.
Signed-off-by: Xiaoliang Yang <xiaoliang.yang_1@nxp.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Oleksij Rempel says:
====================
provide generic net selftest support
changes v3:
- make more granular tests
- enable loopback for all PHYs by default
- fix allmodconfig build errors
- poll for link status update after switching to the loopback mode
changes v2:
- make generic selftests available for all networking devices.
- make use of net_selftest* on FEC, ag71xx and all DSA switches.
- add loopback support on more PHYs.
This patch set provides diagnostic capabilities for some iMX, ag71xx or
any DSA based devices. For proper functionality, PHY loopback support is
needed.
So far there is only initial infrastructure with basic tests.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of generic selftest should be able to work with probably all ethernet
controllers. The DSA switches are not exception, so enable it by default at
least for DSA.
This patch was tested with SJA1105 and AR9331.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With this patch the ag71xx on Atheros AR9331 will able to run generic net
selftests.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With this patch FEC on iMX will able to run generic net selftests
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Port some parts of the stmmac selftest and reuse it as basic generic selftest
library. This patch was tested with following combinations:
- iMX6DL FEC -> AT8035
- iMX6DL FEC -> SJA1105Q switch -> KSZ8081
- iMX6DL FEC -> SJA1105Q switch -> KSZ9031
- AR9331 ag71xx -> AR9331 PHY
- AR9331 ag71xx -> AR9331 switch -> AR9331 PHY
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of loopback, in most cases we need to disable autoneg support
and force some speed configuration. Otherwise, depending on currently
active auto negotiated link speed, the loopback may or may not work.
This patch was tested with following PHYs: TJA1102, KSZ8081, KSZ9031,
AT8035, AR9331.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The generic loopback is really generic and is defined by the 802.3
standard, we should just mandate that drivers implement a custom
loopback if the generic one cannot work.
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch add zh_CN/openrisc to zh_CN/index.
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Reviewed-by: Wu XiangCheng <bobwxc@email.cn>
Link: https://lore.kernel.org/r/162fb50638028c9b0a92a0ce5c53e691be0cfec2.1618568135.git.siyanteng@loongson.cn
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
This patch translates Documentation/openrisc/index.rst into Chinese.
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Reviewed-by: Wu XiangCheng <bobwxc@email.cn>
Link: https://lore.kernel.org/r/f3878525e0d5f94a9c541f5ec8fd31b44a6dc5cd.1618568135.git.siyanteng@loongson.cn
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
This patch translates Documentation/openrisc/todo.rst into Chinese.
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Reviewed-by: Wu XiangCheng <bobwxc@email.cn>
Link: https://lore.kernel.org/r/daf5b352ba62a4737148d524bcae0e64756ed6da.1618568135.git.siyanteng@loongson.cn
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
This patch tranlates Documentation/openrisc/openrisc_port.rst into Chinese
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Reviewed-by: Wu XiangCheng <bobwxc@email.cn>
Link: https://lore.kernel.org/r/e116b3020dfd181c15a59ecf41673cd4dbeea3b2.1618568135.git.siyanteng@loongson.cn
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
This patch add zh_CN/core-api to zh_CN/index.
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Reviewed-by: Wu XiangCheng <bobwxc@email.cn>
Link: https://lore.kernel.org/r/f23ea90fe88a6ac34d29c6642abe9aceba7ccafb.1618568135.git.siyanteng@loongson.cn
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
This patch translates Documentation/core-api/index.rst into Chinese.
add Documentation/translations/zh_CN/core-api/irq/* to zh_CN/core-api/index.rst.
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Reviewed-by: Wu XiangCheng <bobwxc@email.cn>
Link: https://lore.kernel.org/r/d246fcd092111338d64f6b678dda2cd67fcb3f4a.1618568135.git.siyanteng@loongson.cn
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
This patch translates Documentation/core-api/irq/index.rst into Chinese.
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Reviewed-by: Wu XiangCheng <bobwxc@email.cn>
Link: https://lore.kernel.org/r/f6f2edfa645badfdd29122bee3ff0c9577197691.1618568135.git.siyanteng@loongson.cn
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
This patch translates Documentation/core-api/irq/irqflags-tracing.rst into Chinese.
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Reviewed-by: Wu XiangCheng <bobwxc@email.cn>
Link: https://lore.kernel.org/r/deb4b3649d7001f7505672cf45813f0064c9a8d0.1618568135.git.siyanteng@loongson.cn
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
This patch translates Documentation/core-api/irq/irq-domain.rst into Chinese.
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Reviewed-by: Wu XiangCheng <bobwxc@email.cn>
Link: https://lore.kernel.org/r/86e44d36315228408c8bd97360041a9f59a85462.1618568135.git.siyanteng@loongson.cn
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
This patch translates Documentation/core-api/irq/irq-affinity.rst into Chinese.
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Reviewed-by: Wu XiangCheng <bobwxc@email.cn>
Link: https://lore.kernel.org/r/d235db96434baf472441877fc8ffca0f6f70a9f5.1618568135.git.siyanteng@loongson.cn
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
This patch translates Documentation/core-api/irq/concepts.rst into Chinese.
Signed-off-by: Yanteng Si <siyanteng@loongson.cn>
Reviewed-by: Wu XiangCheng <bobwxc@email.cn>
Link: https://lore.kernel.org/r/22babdd7e3fa5121360eff875d005ba5f4647e21.1618568135.git.siyanteng@loongson.cn
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
|
|
Currently docs target is make dependency for TEST_GEN_FILES,
which makes tests to be rebuilt every time you run make.
Adding docs as all target dependency, so when running make
on top of built selftests it will show just:
$ make
make[1]: Nothing to be done for 'docs'.
After cleaning docs, only docs is rebuilt:
$ make docs-clean
CLEAN eBPF_helpers-manpage
CLEAN eBPF_syscall-manpage
$ make
GEN ...selftests/bpf/bpf-helpers.rst
GEN ...selftests/bpf/bpf-helpers.7
GEN ...selftests/bpf/bpf-syscall.rst
GEN ...selftests/bpf/bpf-syscall.2
$ make
make[1]: Nothing to be done for 'docs'.
Fixes: a01d935b2e09 ("tools/bpf: Remove bpf-helpers from bpftool docs")
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Link: https://lore.kernel.org/bpf/20210420132428.15710-1-jolsa@kernel.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fix from Steven Rostedt:
"Fix tp_printk command line and trace events
Masami added a wrapper to be able to unhash trace event pointers as
they are only read by root anyway, and they can also be extracted by
the raw trace data buffers. But this wrapper utilized the iterator to
have a temporary buffer to manipulate the text with.
tp_printk is a kernel command line option that will send the trace
output of a trace event to the console on boot up (useful when the
system crashes before finishing the boot). But the code used the same
wrapper that Masami added, and its iterator did not have a buffer, and
this caused the system to crash.
Have the wrapper just print the trace event normally if the iterator
has no temporary buffer"
* tag 'trace-v5.12-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing: Fix checking event hash pointer logic when tp_printk is enabled
|
|
cap_setfcap is required to create file capabilities.
Since commit 8db6c34f1dbc ("Introduce v3 namespaced file capabilities"),
a process running as uid 0 but without cap_setfcap is able to work
around this as follows: unshare a new user namespace which maps parent
uid 0 into the child namespace.
While this task will not have new capabilities against the parent
namespace, there is a loophole due to the way namespaced file
capabilities are represented as xattrs. File capabilities valid in
userns 1 are distinguished from file capabilities valid in userns 2 by
the kuid which underlies uid 0. Therefore the restricted root process
can unshare a new self-mapping namespace, add a namespaced file
capability onto a file, then use that file capability in the parent
namespace.
To prevent that, do not allow mapping parent uid 0 if the process which
opened the uid_map file does not have CAP_SETFCAP, which is the
capability for setting file capabilities.
As a further wrinkle: a task can unshare its user namespace, then open
its uid_map file itself, and map (only) its own uid. In this case we do
not have the credential from before unshare, which was potentially more
restricted. So, when creating a user namespace, we record whether the
creator had CAP_SETFCAP. Then we can use that during map_write().
With this patch:
1. Unprivileged user can still unshare -Ur
ubuntu@caps:~$ unshare -Ur
root@caps:~# logout
2. Root user can still unshare -Ur
ubuntu@caps:~$ sudo bash
root@caps:/home/ubuntu# unshare -Ur
root@caps:/home/ubuntu# logout
3. Root user without CAP_SETFCAP cannot unshare -Ur:
root@caps:/home/ubuntu# /sbin/capsh --drop=cap_setfcap --
root@caps:/home/ubuntu# /sbin/setcap cap_setfcap=p /sbin/setcap
unable to set CAP_SETFCAP effective capability: Operation not permitted
root@caps:/home/ubuntu# unshare -Ur
unshare: write failed /proc/self/uid_map: Operation not permitted
Note: an alternative solution would be to allow uid 0 mappings by
processes without CAP_SETFCAP, but to prevent such a namespace from
writing any file capabilities. This approach can be seen at [1].
Background history: commit 95ebabde382 ("capabilities: Don't allow
writing ambiguous v3 file capabilities") tried to fix the issue by
preventing v3 fscaps to be written to disk when the root uid would map
to the same uid in nested user namespaces. This led to regressions for
various workloads. For example, see [2]. Ultimately this is a valid
use-case we have to support meaning we had to revert this change in
3b0c2d3eaa83 ("Revert 95ebabde382c ("capabilities: Don't allow writing
ambiguous v3 file capabilities")").
Link: https://git.kernel.org/pub/scm/linux/kernel/git/sergeh/linux.git/log/?h=2021-04-15/setfcap-nsfscaps-v4 [1]
Link: https://github.com/containers/buildah/issues/3071 [2]
Signed-off-by: Serge Hallyn <serge@hallyn.com>
Reviewed-by: Andrew G. Morgan <morgan@kernel.org>
Tested-by: Christian Brauner <christian.brauner@ubuntu.com>
Reviewed-by: Christian Brauner <christian.brauner@ubuntu.com>
Tested-by: Giuseppe Scrivano <gscrivan@redhat.com>
Cc: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
In preparation to enable -Wimplicit-fallthrough for Clang, fix a couple
of warnings by explicitly adding a break statement instead of just
letting the code fall through to the next, and by adding a fallthrough
pseudo-keyword in places whre the code is intended to fall through.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In preparation to enable -Wimplicit-fallthrough for Clang, fix multiple
warnings by explicitly adding multiple goto statements instead of just
letting the code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
|
|
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of letting the code fall
through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Due to a full ring buffer, the driver may be unable to send updates to
the Hyper-V host. But outputing the error message can make the problem
worse because console output is also typically written to the frame
buffer. As a result, in some circumstances the error message is output
continuously.
Break the cycle by rate limiting the error message. Also output
the error code for additional diagnosability.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/1618933459-10585-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
When running in Azure, disks may be connected to a Linux VM with
read/write caching enabled. If a VM panics and issues a VMbus
UNLOAD request to Hyper-V, the response is delayed until all dirty
data in the disk cache is flushed. In extreme cases, this flushing
can take 10's of seconds, depending on the disk speed and the amount
of dirty data. If kdump is configured for the VM, the current 10 second
timeout in vmbus_wait_for_unload() may be exceeded, and the UNLOAD
complete message may arrive well after the kdump kernel is already
running, causing problems. Note that no problem occurs if kdump is
not enabled because Hyper-V waits for the cache flush before doing
a reboot through the BIOS/UEFI code.
Fix this problem by increasing the timeout in vmbus_wait_for_unload()
to 100 seconds. Also output periodic messages so that if anyone is
watching the serial console, they won't think the VM is completely
hung.
Fixes: 911e1987efc8 ("Drivers: hv: vmbus: Add timeout to vmbus_wait_for_unload")
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Link: https://lore.kernel.org/r/1618894089-126662-1-git-send-email-mikelley@microsoft.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
|
If a malicious or compromised Hyper-V sends a spurious message of type
CHANNELMSG_UNLOAD_RESPONSE, the function vmbus_unload_response() will
call complete() on an uninitialized event, and cause an oops.
Reported-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Andrea Parri (Microsoft) <parri.andrea@gmail.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Link: https://lore.kernel.org/r/20210420014350.2002-1-parri.andrea@gmail.com
Signed-off-by: Wei Liu <wei.liu@kernel.org>
|
