| Age | Commit message (Collapse) | Author |
|---|
|
On the msm8998 mtp, the response to the baudrate change command is never
received. On the Lenovo Miix 630, the response to the baudrate change
command is corrupted - "Frame reassembly failed (-84)".
Adding a 50ms delay before re-enabling flow to receive the baudrate change
command response from the wcn3990 addesses both issues, and allows
bluetooth to become functional.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
On Asus MJ401TA (with Realtek ALC256), the headset mic is connected to
pin 0x19, with default configuration value 0x411111f0 (indicating no
physical connection).
Enable this by quirking the pin. Mic jack detection was also tested and
found to be working.
This enables use of the headset mic on this product.
Signed-off-by: Daniel Drake <drake@endlessm.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191017081501.17135-1-drake@endlessm.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
BOSS Katana amplifiers cannot be used for recording or playback if quirks
are applied
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=195223
Signed-off-by: Szabolcs Szőke <szszoke.code@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191011171937.8013-1-szszoke.code@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Sometimes during FW data download stage, in case of an error is
encountered the controller device could not be recovered. To recover
from such failures send Intel hard Reset to re-trigger FW download in
following error scenarios:
1. Intel Read version command error
2. Firmware download timeout
3. Failure in Intel Soft Reset for switching to operational FW
4. Boot timeout for switching to operaional FW
Signed-off-by: Raghuram Hegde <raghuram.hegde@intel.com>
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
During the setup() stage, HCI device drivers expect the chip to
acknowledge its setup() completion via vendor specific frames.
If userspace opens() such HCI device in HCI_USER_CHANNEL [1] mode,
the vendor specific frames are never tranmitted to the driver, as
they are filtered in hci_rx_work().
Allow HCI devices which operate in HCI_USER_CHANNEL mode to receive
frames if the HCI device is is HCI_INIT state.
[1] https://www.spinics.net/lists/linux-bluetooth/msg37345.html
Fixes: 23500189d7e0 ("Bluetooth: Introduce new HCI socket channel for user operation")
Signed-off-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The option --sort=ORDER was only introduced in tar 1.28 (2014), which
is rather new and might not be available in some setups.
This patch tries to replicate the previous behaviour as closely as
possible to fix the kheaders build for older environments. It does
not produce identical archives compared to the previous version due
to minor sorting differences but produces reproducible results itself
in my tests.
Reported-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Dmitry Goldin <dgoldin+lkml@protonmail.ch>
Tested-by: Andreas Schwab <schwab@suse.de>
Tested-by: Quentin Perret <qperret@google.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This pull request clarifies maintainership of the BCM2711 and adds a replacement
mail address for a former contributor.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
disable ptp_ref_clk in suspend flow, and enable it in resume flow.
Fixes: f573c0b9c4e0 ("stmmac: move stmmac_clk, pclk, clk_ptp_ref and stmmac_rst to platform structure")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some drivers just call phy_ethtool_ksettings_set() to set the
links, for those phy drivers that use genphy_read_status(), if
autoneg is on, and the link is up, than execute "ethtool -s
ethx autoneg on" will cause "link partner" information disappear.
The call trace is phy_ethtool_ksettings_set()->phy_start_aneg()
->linkmode_zero(phydev->lp_advertising)->genphy_read_status(),
the link didn't change, so genphy_read_status() just return, and
phydev->lp_advertising is zero now.
This patch moves the clear operation of lp_advertising from
phy_start_aneg() to genphy_read_lpa()/genphy_c45_read_lpa(), and
if autoneg on and autoneg not complete, just clear what the
generic functions care about.
Fixes: 88d6272acaaa ("net: phy: avoid unneeded MDIO reads in genphy_read_status")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Reviewed-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to extend the rcu_read_lock() section in rxrpc_error_report()
and use rcu_dereference_sk_user_data() instead of plain access
to sk->sk_user_data to make sure all rules are respected.
The compiler wont reload sk->sk_user_data at will, and RCU rules
prevent memory beeing freed too soon.
Fixes: f0308fb07080 ("rxrpc: Fix possible NULL pointer access in ICMP handling")
Fixes: 17926a79320a ("[AF_RXRPC]: Provide secure RxRPC sockets for use by userspace and kernel both")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It appears that some Broadcom controllers (eg BCM20702A0) reject LE Set
Advertising Parameters command if advertising intervals provided are not
within range for undirected and low duty directed advertising.
Workaround this bug by populating min and max intervals with 'valid'
values.
< HCI Command: LE Set Advertising Parameters (0x08|0x0006) plen 15
Min advertising interval: 0.000 msec (0x0000)
Max advertising interval: 0.000 msec (0x0000)
Type: Connectable directed - ADV_DIRECT_IND (high duty cycle) (0x01)
Own address type: Public (0x00)
Direct address type: Random (0x01)
Direct address: E2:F0:7B:9F:DC:F4 (Static)
Channel map: 37, 38, 39 (0x07)
Filter policy: Allow Scan Request from Any, Allow Connect Request from Any (0x00)
> HCI Event: Command Complete (0x0e) plen 4
LE Set Advertising Parameters (0x08|0x0006) ncmd 1
Status: Invalid HCI Command Parameters (0x12)
Signed-off-by: Szymon Janc <szymon.janc@codecoup.pl>
Tested-by: Sören Beye <linux@hypfer.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
All users of this driver have been converted to the serdev based
hci_ll driver. The unused driver can be safely dropped now.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
It looks like in hci_init4_req() the request is being
initialised from cpu-endian data but the packet is specified
to be little-endian. This causes an warning from sparse due
to __le16 to u16 conversion.
Fix this by using cpu_to_le16() on the two fields in the packet.
net/bluetooth/hci_core.c:845:27: warning: incorrect type in assignment (different base types)
net/bluetooth/hci_core.c:845:27: expected restricted __le16 [usertype] tx_len
net/bluetooth/hci_core.c:845:27: got unsigned short [usertype] le_max_tx_len
net/bluetooth/hci_core.c:846:28: warning: incorrect type in assignment (different base types)
net/bluetooth/hci_core.c:846:28: expected restricted __le16 [usertype] tx_time
net/bluetooth/hci_core.c:846:28: got unsigned short [usertype] le_max_tx_time
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
As nice as it would be to update firmware faster, that patch broke
at least two different boards, an OMAP4+WL1285 based Motorola Droid
4, as reported by Sebasian Reichel and the Logic PD i.MX6Q +
WL1837MOD.
This reverts commit a2e02f38eff84f199c8e32359eb213f81f270047.
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Cc: stable@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Rather than parsing the sfp firmware node in phylink, parse it in the
sfp-bus code, so we can re-use this code for PHYs without having to
duplicate the parsing.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch supports loading additional firmware file through
request_firmware().
A firmware file may include a header followed by several blocks
which have different types of firmware. Currently, the supported
types are RTL_FW_END, RTL_FW_PLA, and RTL_FW_USB.
The firmware is used to fix some compatible or hardware issues. For
example, the device couldn't be found after rebooting several times.
The supported chips are
RTL_VER_04 (rtl8153a-2.fw)
RTL_VER_05 (rtl8153a-3.fw)
RTL_VER_06 (rtl8153a-4.fw)
RTL_VER_09 (rtl8153b-2.fw)
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Reviewed-by: Prashant Malani <pmalani@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As preempt-to-busy leaves the request on the HW as the resubmission is
processed, that request may complete in the background and even cause a
second virtual request to enter queue. This second virtual request
breaks our "single request in the virtual pipeline" assumptions.
Furthermore, as the virtual request may be completed and retired, we
lose the reference the virtual engine assumes is held. Normally, just
removing the request from the scheduler queue removes it from the
engine, but the virtual engine keeps track of its singleton request via
its ve->request. This pointer needs protecting with a reference.
v2: Drop unnecessary motion of rq->engine = owner
Fixes: 22b7a426bbe1 ("drm/i915/execlists: Preempt-to-busy")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190923152844.8914-1-chris@chris-wilson.co.uk
(cherry picked from commit b647c7df01b75761b4c0b1cb6f4841088c0b1121)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Daniel Vetter uncovered a nasty cycle in using the mmu-notifiers to
invalidate userptr objects which also happen to be pulled into GGTT
mmaps. That is when we unbind the userptr object (on mmu invalidation),
we revoke all CPU mmaps, which may then recurse into mmu invalidation.
We looked for ways of breaking the cycle, but the revocation on
invalidation is required and cannot be avoided. The only solution we
could see was to not allow such GGTT bindings of userptr objects in the
first place. In practice, no one really wants to use a GGTT mmapping of
a CPU pointer...
Just before Daniel's explosive lockdep patches land in v5.4-rc1, we got
a genuine blip from CI:
<4>[ 246.793958] ======================================================
<4>[ 246.793972] WARNING: possible circular locking dependency detected
<4>[ 246.793989] 5.3.0-gbd6c56f50d15-drmtip_372+ #1 Tainted: G U
<4>[ 246.794003] ------------------------------------------------------
<4>[ 246.794017] kswapd0/145 is trying to acquire lock:
<4>[ 246.794030] 000000003f565be6 (&dev->struct_mutex/1){+.+.}, at: userptr_mn_invalidate_range_start+0x18f/0x220 [i915]
<4>[ 246.794250]
but task is already holding lock:
<4>[ 246.794263] 000000001799cef9 (&anon_vma->rwsem){++++}, at: page_lock_anon_vma_read+0xe6/0x2a0
<4>[ 246.794291]
which lock already depends on the new lock.
<4>[ 246.794307]
the existing dependency chain (in reverse order) is:
<4>[ 246.794322]
-> #3 (&anon_vma->rwsem){++++}:
<4>[ 246.794344] down_write+0x33/0x70
<4>[ 246.794357] __vma_adjust+0x3d9/0x7b0
<4>[ 246.794370] __split_vma+0x16a/0x180
<4>[ 246.794385] mprotect_fixup+0x2a5/0x320
<4>[ 246.794399] do_mprotect_pkey+0x208/0x2e0
<4>[ 246.794413] __x64_sys_mprotect+0x16/0x20
<4>[ 246.794429] do_syscall_64+0x55/0x1c0
<4>[ 246.794443] entry_SYSCALL_64_after_hwframe+0x49/0xbe
<4>[ 246.794456]
-> #2 (&mapping->i_mmap_rwsem){++++}:
<4>[ 246.794478] down_write+0x33/0x70
<4>[ 246.794493] unmap_mapping_pages+0x48/0x130
<4>[ 246.794519] i915_vma_revoke_mmap+0x81/0x1b0 [i915]
<4>[ 246.794519] i915_vma_unbind+0x11d/0x4a0 [i915]
<4>[ 246.794519] i915_vma_destroy+0x31/0x300 [i915]
<4>[ 246.794519] __i915_gem_free_objects+0xb8/0x4b0 [i915]
<4>[ 246.794519] drm_file_free.part.0+0x1e6/0x290
<4>[ 246.794519] drm_release+0xa6/0xe0
<4>[ 246.794519] __fput+0xc2/0x250
<4>[ 246.794519] task_work_run+0x82/0xb0
<4>[ 246.794519] do_exit+0x35b/0xdb0
<4>[ 246.794519] do_group_exit+0x34/0xb0
<4>[ 246.794519] __x64_sys_exit_group+0xf/0x10
<4>[ 246.794519] do_syscall_64+0x55/0x1c0
<4>[ 246.794519] entry_SYSCALL_64_after_hwframe+0x49/0xbe
<4>[ 246.794519]
-> #1 (&vm->mutex){+.+.}:
<4>[ 246.794519] i915_gem_shrinker_taints_mutex+0x6d/0xe0 [i915]
<4>[ 246.794519] i915_address_space_init+0x9f/0x160 [i915]
<4>[ 246.794519] i915_ggtt_init_hw+0x55/0x170 [i915]
<4>[ 246.794519] i915_driver_probe+0xc9f/0x1620 [i915]
<4>[ 246.794519] i915_pci_probe+0x43/0x1b0 [i915]
<4>[ 246.794519] pci_device_probe+0x9e/0x120
<4>[ 246.794519] really_probe+0xea/0x3d0
<4>[ 246.794519] driver_probe_device+0x10b/0x120
<4>[ 246.794519] device_driver_attach+0x4a/0x50
<4>[ 246.794519] __driver_attach+0x97/0x130
<4>[ 246.794519] bus_for_each_dev+0x74/0xc0
<4>[ 246.794519] bus_add_driver+0x13f/0x210
<4>[ 246.794519] driver_register+0x56/0xe0
<4>[ 246.794519] do_one_initcall+0x58/0x300
<4>[ 246.794519] do_init_module+0x56/0x1f6
<4>[ 246.794519] load_module+0x25bd/0x2a40
<4>[ 246.794519] __se_sys_finit_module+0xd3/0xf0
<4>[ 246.794519] do_syscall_64+0x55/0x1c0
<4>[ 246.794519] entry_SYSCALL_64_after_hwframe+0x49/0xbe
<4>[ 246.794519]
-> #0 (&dev->struct_mutex/1){+.+.}:
<4>[ 246.794519] __lock_acquire+0x15d8/0x1e90
<4>[ 246.794519] lock_acquire+0xa6/0x1c0
<4>[ 246.794519] __mutex_lock+0x9d/0x9b0
<4>[ 246.794519] userptr_mn_invalidate_range_start+0x18f/0x220 [i915]
<4>[ 246.794519] __mmu_notifier_invalidate_range_start+0x85/0x110
<4>[ 246.794519] try_to_unmap_one+0x76b/0x860
<4>[ 246.794519] rmap_walk_anon+0x104/0x280
<4>[ 246.794519] try_to_unmap+0xc0/0xf0
<4>[ 246.794519] shrink_page_list+0x561/0xc10
<4>[ 246.794519] shrink_inactive_list+0x220/0x440
<4>[ 246.794519] shrink_node_memcg+0x36e/0x740
<4>[ 246.794519] shrink_node+0xcb/0x490
<4>[ 246.794519] balance_pgdat+0x241/0x580
<4>[ 246.794519] kswapd+0x16c/0x530
<4>[ 246.794519] kthread+0x119/0x130
<4>[ 246.794519] ret_from_fork+0x24/0x50
<4>[ 246.794519]
other info that might help us debug this:
<4>[ 246.794519] Chain exists of:
&dev->struct_mutex/1 --> &mapping->i_mmap_rwsem --> &anon_vma->rwsem
<4>[ 246.794519] Possible unsafe locking scenario:
<4>[ 246.794519] CPU0 CPU1
<4>[ 246.794519] ---- ----
<4>[ 246.794519] lock(&anon_vma->rwsem);
<4>[ 246.794519] lock(&mapping->i_mmap_rwsem);
<4>[ 246.794519] lock(&anon_vma->rwsem);
<4>[ 246.794519] lock(&dev->struct_mutex/1);
<4>[ 246.794519]
*** DEADLOCK ***
v2: Say no to mmap_ioctl
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111744
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111870
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190928082546.3473-1-chris@chris-wilson.co.uk
(cherry picked from commit a4311745bba9763e3c965643d4531bd5765b0513)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
The first come first served apporoach to handling the VBT
child device AUX ch conflicts has backfired. We have machines
in the wild where the VBT specifies both port A eDP and
port E DP (in that order) with port E being the real one.
So let's try to flip the preference around and let the last
child device win once again.
Cc: stable@vger.kernel.org
Cc: Jani Nikula <jani.nikula@intel.com>
Tested-by: Masami Ichikawa <masami256@gmail.com>
Tested-by: Torsten <freedesktop201910@liggy.de>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111966
Fixes: 36a0f92020dc ("drm/i915/bios: make child device order the priority order")
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191011202030.8829-1-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
(cherry picked from commit 41e35ffb380bde1379e4030bb5b2ac824d5139cf)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
Pull setting -EIO on the hung requests into its own utility function.
Having allowed ourselves to short-circuit submission of completed
requests, we can now do the mark_eio() prior to submission and avoid
some redundant operations.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190923110056.15176-4-chris@chris-wilson.co.uk
(cherry picked from commit 0d7cf7bc15e75bf79f2f65d61d19f896609f816a)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
This reverts commit b0818f80c8c1bc215bba276bd61c216014fab23b.
Started seeing weird behavior after this patch especially in
the IPv6 code path. Haven't root caused it, but since this was
applied to net branch, taking a precautionary measure to revert
it and look / analyze those failures
Revert this now and I'll send a better fix after analysing / fixing
the weirdness observed.
CC: Eric Dumazet <edumazet@google.com>
CC: Wei Wang <weiwan@google.com>
CC: David S. Miller <davem@davemloft.net>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bpf stackmap with build-id lookup (BPF_F_STACK_BUILD_ID) can trigger A-A
deadlock on rq_lock():
rcu: INFO: rcu_sched detected stalls on CPUs/tasks:
[...]
Call Trace:
try_to_wake_up+0x1ad/0x590
wake_up_q+0x54/0x80
rwsem_wake+0x8a/0xb0
bpf_get_stack+0x13c/0x150
bpf_prog_fbdaf42eded9fe46_on_event+0x5e3/0x1000
bpf_overflow_handler+0x60/0x100
__perf_event_overflow+0x4f/0xf0
perf_swevent_overflow+0x99/0xc0
___perf_sw_event+0xe7/0x120
__schedule+0x47d/0x620
schedule+0x29/0x90
futex_wait_queue_me+0xb9/0x110
futex_wait+0x139/0x230
do_futex+0x2ac/0xa50
__x64_sys_futex+0x13c/0x180
do_syscall_64+0x42/0x100
entry_SYSCALL_64_after_hwframe+0x44/0xa9
This can be reproduced by:
1. Start a multi-thread program that does parallel mmap() and malloc();
2. taskset the program to 2 CPUs;
3. Attach bpf program to trace_sched_switch and gather stackmap with
build-id, e.g. with trace.py from bcc tools:
trace.py -U -p <pid> -s <some-bin,some-lib> t:sched:sched_switch
A sample reproducer is attached at the end.
This could also trigger deadlock with other locks that are nested with
rq_lock.
Fix this by checking whether irqs are disabled. Since rq_lock and all
other nested locks are irq safe, it is safe to do up_read() when irqs are
not disable. If the irqs are disabled, postpone up_read() in irq_work.
Fixes: 615755a77b24 ("bpf: extend stackmap to save binary_build_id+offset instead of address")
Signed-off-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191014171223.357174-1-songliubraving@fb.com
Reproducer:
============================ 8< ============================
char *filename;
void *worker(void *p)
{
void *ptr;
int fd;
char *pptr;
fd = open(filename, O_RDONLY);
if (fd < 0)
return NULL;
while (1) {
struct timespec ts = {0, 1000 + rand() % 2000};
ptr = mmap(NULL, 4096 * 64, PROT_READ, MAP_PRIVATE, fd, 0);
usleep(1);
if (ptr == MAP_FAILED) {
printf("failed to mmap\n");
break;
}
munmap(ptr, 4096 * 64);
usleep(1);
pptr = malloc(1);
usleep(1);
pptr[0] = 1;
usleep(1);
free(pptr);
usleep(1);
nanosleep(&ts, NULL);
}
close(fd);
return NULL;
}
int main(int argc, char *argv[])
{
void *ptr;
int i;
pthread_t threads[THREAD_COUNT];
if (argc < 2)
return 0;
filename = argv[1];
for (i = 0; i < THREAD_COUNT; i++) {
if (pthread_create(threads + i, NULL, worker, NULL)) {
fprintf(stderr, "Error creating thread\n");
return 0;
}
}
for (i = 0; i < THREAD_COUNT; i++)
pthread_join(threads[i], NULL);
return 0;
}
============================ 8< ============================
|
|
For the different hardware support options, it is better to use
IS_ENABLED check. Let the compiler do the needed optimizations.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
|
|
The btusb_rtl_cmd_timeout() function is used inside of an
ifdef, leading to a warning when this part is hidden
from the compiler:
drivers/bluetooth/btusb.c:530:13: error: unused function 'btusb_rtl_cmd_timeout' [-Werror,-Wunused-function]
Use an IS_ENABLED() check instead so the compiler can see
the code and then discard it silently.
Fixes: d7ef0d1e3968 ("Bluetooth: btusb: Use cmd_timeout to reset Realtek device")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
After FW download there is no print to confirm the current
FW version. Add print to check FW version incase of FW download.
Signed-off-by: Amit K Bag <amit.k.bag@intel.com>
Signed-off-by: Yoni Shavit <yshavit@chromium.org>
Signed-off-by: Chethan Tumkur Narayan <chethan.tumkur.narayan@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
It does not need the '-' for PTR_ERR(skb) because PTR_ERR(skb) will
return the negative value during errors.
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
'skb_pad()' a few lines above already initializes the "padded" byte to 0.
So there is no need to do it twice.
All what is needed is to increase the len of the skb. So 'skb_put(..., 1)'
is enough here.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
net/bluetooth/smp.c: In function 'smp_irk_matches':
net/bluetooth/smp.c:505:18: warning: variable 'smp' set but not used [-Wunused-but-set-variable]
net/bluetooth/smp.c: In function 'smp_generate_rpa':
net/bluetooth/smp.c:526:18: warning: variable 'smp' set but not used [-Wunused-but-set-variable]
It is not used since commit 28a220aac596 ("bluetooth: switch
to AES library")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Sign-extending TTBR1 addresses when converting to an untagged address
breaks the documented POSIX semantics for mlock() in some obscure error
cases where we end up returning -EINVAL instead of -ENOMEM as a direct
result of rewriting the upper address bits.
Rework the untagged_addr() macro to preserve the upper address bits for
TTBR1 addresses and only clear the tag bits for user addresses. This
matches the behaviour of the 'clear_address_tag' assembly macro, so
rename that and align the implementations at the same time so that they
use the same instruction sequences for the tag manipulation.
Link: https://lore.kernel.org/stable/20191014162651.GF19200@arrakis.emea.arm.com/
Reported-by: Jan Stancek <jstancek@redhat.com>
Tested-by: Jan Stancek <jstancek@redhat.com>
Reviewed-by: Catalin Marinas <catalin.marinas@arm.com>
Tested-by: Catalin Marinas <catalin.marinas@arm.com>
Reviewed-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Tested-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Reviewed-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
When detecting a spurious EL1 translation fault, we have the CPU retry
the translation using an AT S1E1R instruction, and inspect PAR_EL1 to
determine if the fault was spurious.
When PAR_EL1.F == 0, the AT instruction successfully translated the
address without a fault, which implies the original fault was spurious.
However, in this case we return false and treat the original fault as if
it was not spurious.
Invert the return value so that we treat such a case as spurious.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Fixes: 42f91093b043 ("arm64: mm: Ignore spurious translation faults taken from the kernel")
Tested-by: James Morse <james.morse@arm.com>
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
The 'F' field of the PAR_EL1 register lives in bit 0, not bit 1.
Fix the broken definition in 'sysreg.h'.
Fixes: e8620cff9994 ("arm64: sysreg: Add some field definitions for PAR_EL1")
Reviewed-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
Preempting from IRQ-return means that the task has its PSTATE saved
on the stack, which will get restored when the task is resumed and does
the actual IRQ return.
However, enabling some CPU features requires modifying the PSTATE. This
means that, if a task was scheduled out during an IRQ-return before all
CPU features are enabled, the task might restore a PSTATE that does not
include the feature enablement changes once scheduled back in.
* Task 1:
PAN == 0 ---| |---------------
| |<- return from IRQ, PSTATE.PAN = 0
| <- IRQ |
+--------+ <- preempt() +--
^
|
reschedule Task 1, PSTATE.PAN == 1
* Init:
--------------------+------------------------
^
|
enable_cpu_features
set PSTATE.PAN on all CPUs
Worse than this, since PSTATE is untouched when task switching is done,
a task missing the new bits in PSTATE might affect another task, if both
do direct calls to schedule() (outside of IRQ/exception contexts).
Fix this by preventing preemption on IRQ-return until features are
enabled on all CPUs.
This way the only PSTATE values that are saved on the stack are from
synchronous exceptions. These are expected to be fatal this early, the
exception is BRK for WARN_ON(), but as this uses do_debug_exception()
which keeps IRQs masked, it shouldn't call schedule().
Signed-off-by: Julien Thierry <julien.thierry@arm.com>
[james: Replaced a really cool hack, with an even simpler static key in C.
expanded commit message with Julien's cover-letter ascii art]
Signed-off-by: James Morse <james.morse@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/song/md into for-linus
Pull MD fix from Song.
* 'md-fixes' of https://git.kernel.org/pub/scm/linux/kernel/git/song/md:
md/raid0: fix warning message for parameter default_layout
|
|
The message should match the parameter, i.e. raid0.default_layout.
Fixes: c84a1372df92 ("md/raid0: avoid RAID0 data corruption due to layout confusion.")
Cc: NeilBrown <neilb@suse.de>
Reported-by: Ivan Topolsky <doktor.yak@gmail.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
|
|
The __kthread_queue_delayed_work is not exported so
make it static, to avoid the following sparse warning:
kernel/kthread.c:869:6: warning: symbol '__kthread_queue_delayed_work' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
AST2600 EMMC support 3 types DAT bus sizes (1, 4 and 8-bit),
corresponding to 3 groups: EMMCG1, EMMCG4 and EMMCG8
Fixes: 58dc52ad00a0 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-8-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When UART13G1 is set the pinmux configuration in SCU4B8 for UART13G0
should be cleared.
Fixes: 58dc52ad00a0 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
[AJ: Tweak commit message]
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-7-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Signal descriptors can represent multi-bit bitfields and so have
explicit "enable" and "disable" states. However many descriptor
instances only describe a single bit, and so the SIG_DESC_SET() macro is
provides an abstraction for the single-bit cases: Its expansion
configures the "enable" state to set the bit and "disable" to clear.
SIG_DESC_CLEAR() was introduced to provide a similar single-bit
abstraction for for descriptors to clear the bit of interest. However
its behaviour was defined as the literal inverse of SIG_DESC_SET() - the
impact is the bit of interest is set in the disable path. This behaviour
isn't intuitive and doesn't align with how we want to use the macro in
practice, so make it clear the bit for both the enable and disable
paths.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-6-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The documentation to configure I3C3/FSI1 and I3C4/FSI2 was initially
unclear.
Fixes: 58dc52ad00a0 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Johnny Huang <johnny_huang@aspeedtech.com>
[AJ: Tweak commit message, resolve rebase conflicts]
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-5-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The I2C function the pin participated in was incorrectly named SDA14
which lead to a failure to mux:
[ 6.884344] No function I2C14 found on pin 7 (7). Found signal(s) MACLINK4, SDA14, GPIOA7 for function(s) MACLINK4, SDA14, GPIOA7
Fixes: 58dc52ad00a0 ("pinctrl: aspeed: Add AST2600 pinmux support")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-4-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some pins crept in that weren't ordered in the list.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-3-andrew@aj.id.au
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Rename SD3 functions and groups to EMMC to better reflect their intended
use before the binding escapes too far into the wild. Also clean up the
SD3 pin groups to eliminate some silliness that slipped through the
cracks (SD3DAT[4-7]) by unifying them into three new groups: EMMCG1,
EMMCG4 and EMMCG8 for 1, 4 and 8-bit data buses respectively.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20191008044153.12734-2-andrew@aj.id.au
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The memory @orig_flags is allocated by strdup(), it is freed on the
normal path, but leak to free on the error path.
Fix this by adding free(orig_flags) on the error path.
Fixes: 0e11115644b3 ("perf kmem: Print gfp flags in human readable string")
Signed-off-by: Yunfeng Ye <yeyunfeng@huawei.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Feilong Lin <linfeilong@huawei.com>
Cc: Hu Shiyuan <hushiyuan@huawei.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/f9e9f458-96f3-4a97-a1d5-9feec2420e07@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
On a machine with a 64K PAGE_SIZE, the nested for loops in
test_check_nonzero_user() can lead to soft lockups, eg:
watchdog: BUG: soft lockup - CPU#4 stuck for 22s! [modprobe:611]
Modules linked in: test_user_copy(+) vmx_crypto gf128mul crc32c_vpmsum virtio_balloon ip_tables x_tables autofs4
CPU: 4 PID: 611 Comm: modprobe Tainted: G L 5.4.0-rc1-gcc-8.2.0-00001-gf5a1a536fa14-dirty #1151
...
NIP __might_sleep+0x20/0xc0
LR __might_fault+0x40/0x60
Call Trace:
check_zeroed_user+0x12c/0x200
test_user_copy_init+0x67c/0x1210 [test_user_copy]
do_one_initcall+0x60/0x340
do_init_module+0x7c/0x2f0
load_module+0x2d94/0x30e0
__do_sys_finit_module+0xc8/0x150
system_call+0x5c/0x68
Even with a 4K PAGE_SIZE the test takes multiple seconds. Instead
tweak it to only scan a 1024 byte region, but make it cross the
page boundary.
Fixes: f5a1a536fa14 ("lib: introduce copy_struct_from_user() helper")
Suggested-by: Aleksa Sarai <cyphar@cyphar.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Aleksa Sarai <cyphar@cyphar.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Link: https://lore.kernel.org/r/20191016122732.13467-1-mpe@ellerman.id.au
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
|
|
Make the compiler report a clear error when bpf_helpers_doc.py needs
updating rather than rely on the fact that Clang fails to compile
English:
../../../lib/bpf/bpf_helper_defs.h:2707:1: error: unknown type name 'Unrecognized'
Unrecognized type 'struct bpf_inet_lookup', please add it to known types!
Signed-off-by: Jakub Sitnicki <jakub@cloudflare.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20191016085811.11700-1-jakub@cloudflare.com
|
|
The function should be spdifib, fix this typo.
Fixes: 423ddc580b13 ("pinctrl: berlin: add the as370 SoC pinctrl driver")
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Link: https://lore.kernel.org/r/20191011154321.44f08f9a@xhacker.debian
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If there are neither processor objects nor processor device objects
in the ACPI tables, the per-CPU processors table will not be
initialized and attempting to dereference pointers from there will
cause the kernel to crash. This happens in acpi_processor_ppc_init()
and acpi_thermal_cpufreq_init() after commit d15ce412737a ("ACPI:
cpufreq: Switch to QoS requests instead of cpufreq notifier")
which didn't add the requisite NULL pointer checks in there.
Add the NULL pointer checks to acpi_processor_ppc_init() and
acpi_thermal_cpufreq_init(), and to the corresponding "exit"
routines.
While at it, drop redundant return instructions from
acpi_processor_ppc_init() and acpi_thermal_cpufreq_init().
Fixes: d15ce412737a ("ACPI: cpufreq: Switch to QoS requests instead of cpufreq notifier")
Reported-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
|
|
Use the tdev pointer directly instead of going through the port data
when accessing the serial data in close().
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Fix races between closing a port and opening or closing another port on
the same device which could lead to a failure to start or stop the
shared interrupt URB. The latter could potentially cause a
use-after-free or worse in the completion handler on driver unbind.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The use of u8 and __le16 in this struct assumes that it's going to be
packed to byte alignment. C doesn't guarantee that, so we should mark
this __packed.
Fixes: cc20a7139836 ("rtw88: use struct rtw_fw_hdr to access firmware header")
Cc: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
