| Age | Commit message (Collapse) | Author |
|---|
|
The requirement for mesh link metric refreshing, is that from one
mesh point we be able to send some data frames to other mesh points
which are not currently selected as a primary traffic path, but which
are only 1 hop away. The absence of the primary path to the chosen node
makes it necessary to apply some form of marking on a chosen packet
stream so that the packets can be properly steered to the selected node
for testing, and not by the regular mesh path lookup.
Tested-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Allows setting of control flags of skb cb - if needed -
when calling ieee80211_subif_start_xmit().
Tested-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Adding support to allow mesh HWMP to measure link metrics on unexercised
direct mesh path by sending some data frames to other mesh points which
are not currently selected as a primary traffic path but only 1 hop away.
The absence of the primary path to the chosen node makes it necessary to
apply some form of marking on a chosen packet stream so that the packets
can be properly steered to the selected node for testing, and not by the
regular mesh path lookup.
Tested-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Mac80211 SW crypto handles replacing PTK keys correctly.
Don't trigger needless warnings or workarounds when the driver can only
use the known good SW crypto provided by mac80211.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Allow Extended Key ID to be used with hwsim.
Hwsim can only communicate with other hwsim cards, allowing it to bypass
creation of A-MPDUs in the first place.
Mixing keyIDs in an A-MPDU is therefore impossible and can never cause
interoperability issues with other cards.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[reword comment slightly]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We are copying one entire structure to another of the same type in
nl80211_notify_radar_detection, so it's simpler and safer to do a
struct assignment instead of memcpy().
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Only enable Extended Key ID support for drivers which are not supporting
crypto offload and also do not support A-MPDU.
While any driver using SW crypto from mac80211 is generally able to also
support Extended Key ID these drivers are likely to mix keyIDs in
AMPDUs when rekeying.
According to IEEE 802.11-2016 "9.7.3 A-MPDU contents" this is not
allowed.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[reword comment a bit, move ! into logic expression]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The cfg80211_merge_profile() and ieee802_11_find_bssid_profile() are
a bit cleaner if we just pass the merged_ie pointer instead of a pointer
to the pointer.
This isn't a functional change, it's just a clean up.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch introduce a new driver callback drv_sta_set_txpwr. This API will
copy the transmit power value passed from user space and call the driver
callback to set the tx power for the station.
Co-developed-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Ashok Raj Nagarajan <arnagara@codeaurora.org>
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This patch adds support to set transmit power setting type and transmit
power level attributes to NL80211_CMD_SET_STATION in order to facilitate
adjusting the transmit power level of a station associated to the AP.
The added attributes allow selection of automatic and limited transmit
power level, with the level defined in dBm format.
Co-developed-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Ashok Raj Nagarajan <arnagara@codeaurora.org>
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There's no need to allocate than one queue in the iTXQs case
now that we no longer use ndo_select_queue to assign the AC.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)
Notice that, in this case, variable size_of_regd is not necessary,
hence it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct foo {
int stuff;
struct boo entry[];
};
size = sizeof(struct foo) + count * sizeof(struct boo);
instance = kzalloc(size, GFP_KERNEL)
Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:
instance = kzalloc(struct_size(instance, entry, count), GFP_KERNEL)
Notice that, in this case, variable size_of_regd is not necessary,
hence it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
At Technical University of Munich we use MAC 802.11 TX status frames to
perform several measurements in MAC 802.11 setups.
With ath based drivers this was possible until commit d94a461d7a7df6
("ath9k: use ieee80211_tx_status_noskb where possible") as the driver
ignored the IEEE80211_TX_CTL_REQ_TX_STATUS flag and always delivered
tx_status frames. Since that commit, this behavior was changed and the
driver now adheres to IEEE80211_TX_CTL_REQ_TX_STATUS.
Due to performance reasons, IEEE80211_TX_CTL_REQ_TX_STATUS is not set for
data frames from interfaces in managed mode. Hence, frames that are sent
from a managed mode interface do never deliver tx_status frames. This
remains true even if a monitor mode interface (the measurement interface)
is added to the same ieee80211 physical device. Thus, there is no
possibility for receiving tx_status frames for frames sent on an interface
in managed mode, if the driver adheres to IEEE80211_TX_CTL_REQ_TX_STATUS.
In order to force delivery of tx_status frames for research and debugging
purposes, implement a debugfs option force_tx_status for ieee80211 physical
devices. When this option is set for a physical device,
IEEE80211_TX_CTL_REQ_TX_STATUS is enabled in all packets sent from that
device. This option can be set via
/sys/kernel/debug/ieee80211/<dev>/force_tx_status. The default is disabled.
Co-developed-by: Charlie Groh <ga58taw@mytum.de>
Signed-off-by: Charlie Groh <ga58taw@mytum.de>
Signed-off-by: Julius Niedworok <julius.n@gmx.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The zero check on variable changed is redundant as it must be
between 1 and 3 at the end of the proceeding if statement block.
Remove the redundant check.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
FullMAC STAs have no way to update bss channel after CSA channel switch
completion. As a result, user-space tools may provide inconsistent
channel info. For instance, consider the following two commands:
$ sudo iw dev wlan0 link
$ sudo iw dev wlan0 info
The latter command gets channel info from the hardware, so most probably
its output will be correct. However the former command gets channel info
from scan cache, so its output will contain outdated channel info.
In fact, current bss channel info will not be updated until the
next [re-]connect.
Note that mac80211 STAs have a workaround for this, but it requires
access to internal cfg80211 data, see ieee80211_chswitch_work:
/* XXX: shouldn't really modify cfg80211-owned data! */
ifmgd->associated->channel = sdata->csa_chandef.chan;
This patch suggests to convert mac80211 workaround into cfg80211 behavior
and to update current bss channel in cfg80211_ch_switch_notify.
Signed-off-by: Sergey Matyukevich <sergey.matyukevich.os@quantenna.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
A per-group shift was added to reduce the size of the per-rate transmit
duration field to u16 without sacrificing a lot of precision
This patch changes the macros to automatically calculate the best value for
this shift based on the lowest rate within the group.
This simplifies adding more groups and slightly improves accuracy for some of
the existing groups.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This is needed for the upcoming driver for MT7615 4x4 802.11ac chipsets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When using iTXQ, the network stack does not need the real queue number, since
mac80211 is using its internal queues anyway. In that case we can defer
selecting the queue and remove a redundant station lookup in the tx path to save
some CPU cycles.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add support for Extended Key ID as defined in IEEE 802.11-2016.
- Implement the nl80211 API for Extended Key ID
- Extend mac80211 API to allow drivers to support Extended Key ID
- Enable Extended Key ID by default for drivers only supporting SW
crypto (e.g. mac80211_hwsim)
- Allow unicast Tx usage to be supressed (IEEE80211_KEY_FLAG_NO_AUTO_TX)
- Select the decryption key based on the MPDU keyid
- Enforce existing assumptions in the code that rekeys don't change the
cipher
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[remove module parameter]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add support for IEEE 802.11-2016 "Extended Key ID for Individually
Addressed Frames".
Extend cfg80211 and nl80211 to allow pairwise keys to be installed for
Rx only, enable Tx separately and allow Key ID 1 for pairwise keys.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
[use NLA_POLICY_RANGE() for NL80211_KEY_MODE]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Optimize/cleanup the delay tailroom checks and adds one missing tailroom
update.
Signed-off-by: Alexander Wetzel <alexander@wetzel-home.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When using iTXQ, tx sequence number allocation and statistics are run at
dequeue time. Because of that, it is safe to enable NETIF_F_LLTX, which
allows tx handlers to run on multiple CPUs in parallel.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Reduces lock contention on enqueue/dequeue of iTXQ packets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Reduces lock contention on enqueue/dequeue of iTXQ packets
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The callers of these functions are all within RCU locked sections
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Update the out-dated comments as well, and have them point to
the correct sections in the D4.0 spec.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since an element is limited to 255 octets, a profile may be split
split to several elements. Support the split as defined in the 11ax
draft 3.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Since an element is limited to 255 octets, a profile may be split
split to several elements. Support the split as defined in the 11ax
draft 3. Detect legacy split and print a net-rate limited warning,
since there is no ROI in supporting this probably non-existent
split.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Subelement profile may specify element IDs it doesn't inherit
from the management frame. Support it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Subelement profile may specify element IDs it doesn't inherit
from the management frame. Support it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
When creating the IEs for the nontransmitted BSS, the index
element is skipped. However, we need to get DTIM values from
it, so don't skip it.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
P2P device interface type was not indicated in the supported
interface types even when hwsim was configured with p2p device
support. Fix it.
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The iwlwifi driver creates one rule per channel, thus it needs more
rules than normal. To solve this, increase NL80211_MAX_SUPP_REG_RULES
so iwlwifi can also fit UHB (ultra high band) channels.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf 2019-04-25
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) the bpf verifier fix to properly mark registers in all stack frames, from Paul.
2) preempt_enable_no_resched->preempt_enable fix, from Peter.
3) other misc fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jiri Pirko says:
====================
netdevsim: implement proper device model
Currently the model of netdevsim is a bit odd in multiple ways.
1) devlink instance is not in any way related with actual netdevsim
netdevices. Instead, it is created per-namespace.
2) multi-port netdevsim device is done using "link" attribute.
3) netdevsim bus is there only to have something to bind the netdev to,
it really does not act as a bus.
4) netdevsim instances are created by "ip link add" which is great for
soft devices with no hw backend. The rtnl core allocates netdev and
calls into driver holding rtnl mutex. For hw-backed devices, this
flow is wrong as it breaks order in which things are done.
This patchset adjust netdevsim to fix all above.
In order to support proper devlink and devlink port instances and to be
able to emulate real devices, there is need to implement bus probe and
instantiate everything from there. User can specify device id and port
count to be instantianted. For example:
$ echo "10 4" > /sys/bus/netdevsim/new_device
Then devlink shows this:
$ devlink dev
netdevsim/netdevsim10
$ devlink port
netdevsim/netdevsim10/0: type eth netdev eni0np1 flavour physical
netdevsim/netdevsim10/1: type eth netdev eni0np2 flavour physical
netdevsim/netdevsim10/2: type eth netdev eni0np3 flavour physical
netdevsim/netdevsim10/3: type eth netdev eni0np4 flavour physical
There is possible to add and delete ports using their indexes
during netdevsim device lifetime like this:
Then devlink shows this:
$ devlink port
netdevsim/netdevsim10/1: type eth netdev eni10np2 flavour physical
netdevsim/netdevsim10/2: type eth netdev eni10np3 flavour physical
netdevsim/netdevsim10/3: type eth netdev eni10np4 flavour physical
netdevsim/netdevsim10/43: type eth netdev eni10np44 flavour physical
Debugfs topology is also adjusted a bit. The rest stays the same as
before.
Udev bits are merged un systemd upstream git:
https://github.com/systemd/systemd/commit/eaa9d507d85509c8bf727356e3884ec54b0fc646
See individual patches for changelog.
====================
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement ndo_get_devlink_port and allow switch_id and port_name to be
handled by devlink.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the existing way to create netdevsim over rtnetlink and move the
netdev creation/destruction to dev probe, so for every probed port,
a netdevsim-netdev instance is created.
Adjust selftests to work with new interface.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to test flows in core, it is beneficial to maintain previously
supported possibility to add and delete ports during netdevsim lifetime.
Do it by extending device sysfs attrs by "new_port" and "del_port".
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement netdevsim bus probing of netdevsim devices. For every probed
device create a devlink instance. According to the user-passed value,
create a number of ports represented by devlink port instances.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the model where dev is represented by devlink and ports are
represented by devlink ports, make debugfs file names independent
on netdev names. Change the topology to the one illustrated
by the following example:
$ ls /sys/kernel/debug/netdevsim/
netdevsim1
$ ls /sys/kernel/debug/netdevsim/netdevsim1/
bpf_bind_accept bpf_bind_verifier_delay bpf_bound_progs ports
$ ls /sys/kernel/debug/netdevsim/netdevsim1/ports/
0 1
$ ls /sys/kernel/debug/netdevsim/netdevsim1/ports/0/
bpf_map_accept bpf_offloaded_id bpf_tc_accept bpf_tc_non_bound_accept bpf_xdpdrv_accept bpf_xdpoffload_accept dev ipsec
$ ls /sys/kernel/debug/netdevsim/netdevsim1/ports/0/dev -l
lrwxrwxrwx 1 root root 0 Apr 13 15:58 /sys/kernel/debug/netdevsim/netdevsim1/ports/0/dev -> ../../../netdevsim1
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current implementation of parent_id/switch_id does not follow the
original idea of being unique. The values are "0", "1", etc. Instead of
that, generate 32 random bytes.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As previously introduce dev which is mapped 1:1 to a bus device covers
the purpose of the original shared device, merge the sdev code into dev.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These functions are going to be called from bus probe/release(),
therefore make them independent on ns struct and rename accordingly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a way to add new netdevsim device on netdevsim bus and also to
delete existing netdevsim device from the bus. Track the bus devices
in using a list.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of increments of u32 value, use ida to manage bus device ids.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to bus probing to work correctly, register a simple netdevsim
driver implementation.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move netdevsim device registration into bus.c and alongside with that
the related sysfs attributes. Introduce new struct nsim_bus_dev to
represent a netdevsim device on netdevsim bus.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the code related to netdevsim bus is going to get bigger, move the
existing code to a separate file.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The existing devlink.c code is going to be extended to represent asic
device on a bus. As this is about more than just devlink,
rename the file. Do appropriate prefix renaming alongside with that.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
