| Age | Commit message (Collapse) | Author |
|---|
|
A slow SPI bus clocks at ~20MHz, which means it would transfer about
2500 bytes per second with a single data line. Big transfers, like when
dealing with flashes can easily reach a few MiB. The current DMA timeout
is set to 1 second, which means any working transfer of about 4MiB will
always be cancelled.
With the above derivations, on a slow bus, we can assume every byte will
take at most 0.4ms. Said otherwise, we could add 4ms to the 1-second
timeout delay every 10kiB. On a 4MiB transfer, it would bring the
timeout delay up to 2.6s which still seems rather acceptable for a
timeout.
The consequence of this is that long transfers might be allowed, which
hence requires the need to interrupt the transfer if wanted by the
user. We can hence switch to the _interruptible variant of
wait_for_completion. This leads to a little bit more handling to also
handle the interrupted case but looks really acceptable overall.
While at it, we drop the useless, noisy and redundant WARN_ON() call.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Ryan Wanner <ryan.wanner@microchip.com>
Link: https://lore.kernel.org/r/Message-Id: <20230622090634.3411468-3-miquel.raynal@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Switch the DT binding to a YAML schema to enable the DT validation.
There was also an incorrect reference to dma-names being "rxtx" where
the driver and existing device trees actually use dma-names = "data" so
this is corrected in the conversion.
Signed-off-by: Vadym Kochan <vadym.kochan@plvision.eu>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230619040742.1108172-2-chris.packham@alliedtelesis.co.nz
|
|
Reference mtd-physmap.yaml which contains all the relevant properties
for this device. Add "unevaluatedProperties: false" to avoid any
spurious addition of random properties.
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-18-miquel.raynal@bootlin.com
|
|
nand-on-flash-bbt is a generic property which may apply to any raw NAND
chip, it does not need to be listed in each controller
description. The raw NAND chip description file which contains the
property is already referenced, so no need to mention the property here
again.
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-17-miquel.raynal@bootlin.com
|
|
The mediatek NAND controller should reference the new raw-nand-chip.yaml
binding instead of the original nand-chip.yaml which does not contain
*all* the properties that may be used to fully describe the NAND
devices, certain properties being actually described under
nand-controller.yaml.
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: Xiangsheng Hou <xiangsheng.hou@mediatek.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-16-miquel.raynal@bootlin.com
|
|
List all the possible properties in the NAND chip as per the example and
set unevaluatedProperties to false in the NAND chip section.
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Christophe Kerello <christophe.kerello@foss.st.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-15-miquel.raynal@bootlin.com
|
|
List all the possible properties in the NAND chip as per the example and
set unevaluatedProperties to false in the NAND chip section.
Cc: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-14-miquel.raynal@bootlin.com
|
|
nand-ecc-mode is a generic property which may apply to any raw NAND
chip, it does not need to be listed in each controller
description. Instead, let's reference the raw NAND chip description file
which contains the property. The description contained
"additionalProperties: false" which is wrong as other properties such as
partitions might very well be added in the final .dts, and anyway needs
to be converted into "unexpectedProperties: false" to fit the property
change new requirements.
Cc: Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-13-miquel.raynal@bootlin.com
|
|
Ensure all raw NAND chip properties are valid by referencing the
relevant schema and set unevaluatedProperties to false in the NAND chip
section to avoid spurious additions of random properties.
Doing this in one location also saves us from dupplicating the
description of the NAND chip object.
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-12-miquel.raynal@bootlin.com
|
|
Ensure all raw NAND chip properties are valid by referencing the
relevant schema and set unevaluatedProperties to false in the NAND chip
section to avoid spurious additions of random properties.
Cc: Brian Norris <computersforpeace@gmail.com>
Cc: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-11-miquel.raynal@bootlin.com
|
|
Ensure all raw NAND chip properties are valid by referencing the
relevant schema and set unevaluatedProperties to false in the NAND chip
section to avoid spurious additions of random properties.
Cc: Liang Yang <liang.yang@amlogic.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-10-miquel.raynal@bootlin.com
|
|
nand-ecc-mode is a generic property which may apply to any raw NAND
chip, it does not need to be listed in each controller
description. Instead, let's reference the raw NAND chip description file
which contains the property. The description contained
"additionalProperties: false" which is wrong as other properties such as
partitions might very well be added in the final .dts, and anyway needs
to be converted into "unexpectedProperties: false" to fit the property
change new requirements.
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Samuel Holland <samuel@sholland.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-9-miquel.raynal@bootlin.com
|
|
List all the possible properties in the NAND chip as per the example and
set unevaluatedProperties to false in the NAND chip section.
Cc: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-8-miquel.raynal@bootlin.com
|
|
List all the possible properties in the NAND chip as per the example and
set unevaluatedProperties to false in the NAND chip section.
Cc: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-7-miquel.raynal@bootlin.com
|
|
qcom,boot-partitions is a NAND chip property, not a NAND controller
property. Move the description of the property into the NAND chip
section and just enable the property in the if/else block.
Fixes: 5278cc93a97f ("dt-bindings: mtd: qcom_nandc: document qcom,boot-partitions binding")
Cc: Manivannan Sadhasivam <mani@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-6-miquel.raynal@bootlin.com
|
|
This property has been extensively used for almost two decades already,
a lot of device trees use it, this is not the preferred way to configure
the ECC engines but we cannot just ignore it. Describe the property,
list the exact strings which have once been supported and mark it
deprecated.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-5-miquel.raynal@bootlin.com
|
|
The nand-ecc-placement property has been deprecated for a long time
already, it does not really mean something useful for the ECC engines
and is anyway in the vast majority of cases totally useless. Just mark
it deprecated to avoid appealing people to use it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-4-miquel.raynal@bootlin.com
|
|
In an effort to constrain as much as we can the existing binding, we
want to add "unevaluatedProperties: false" in all the NAND chip
descriptions part of NAND controller bindings. But in order to do that
properly, we also need to reference a file which contains all the
"allowed" properties. Right now this file is nand-chip.yaml but in
practice raw NAND controllers may use additional properties in their
NAND chip children node. These properties are listed under
nand-controller.yaml, which makes the "unevaluatedProperties" checks
fail while the description are valid. We need to move these NAND chip
related properties into another file, because we do not want to pollute
nand-chip.yaml which is also referenced by eg. SPI-NAND devices.
Let's create a raw-nand-chip.yaml file to reference all the properties a
raw NAND chip description can contain. The chain of inheritance becomes:
nand-controller.yaml <- raw-nand-chip.yaml
raw-nand-chip.yaml <- nand-chip.yaml
spi-nand.yaml <- nand-chip.yaml
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-3-miquel.raynal@bootlin.com
|
|
There is no addition there, but the mtd.yaml file is so generic, it can
be referenced by a wide variety of devices, including nand ones which
already define the node name to "nand@<cs>". Right now it does not lead
to any failure but when we will constrain more the schema, this will
become a problem because we want the mtd-wide properties like label or
partitions to be available for the callers.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/linux-mtd/20230619092916.3028470-2-miquel.raynal@bootlin.com
|
|
Fix typo in the description of the 'succesfull'.
Signed-off-by: Bo Liu <liubo03@inspur.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20230621020331.1508-1-wangdeming@inspur.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm64 fixes for 6.4, take #4
- Correctly save/restore PMUSERNR_EL0 when host userspace is using
PMU counters directly
- Fix GICv2 emulation on GICv3 after the locking rework
- Don't use smp_processor_id() in kvm_pmu_probe_armpmu(), and
document why...
|
|
Just like for sc7180 devices using the Chrome bootflow (AKA trogdor
and IDP), sc7280 devices using the Chrome bootflow also need their
firmware marked dma-coherent. On sc7280 this wasn't causing WiFi to
fail to startup, since WiFi works differently there. However, on
sc7280 devices we were still getting the message at bootup after
commit 7bd6680b47fa ("Revert "Revert "arm64: dma: Drop cache
invalidation from arch_dma_prep_coherent()"""):
qcom_scm firmware:scm: Assign memory protection call failed -22
qcom_rmtfs_mem 9c900000.memory: assign memory failed
qcom_rmtfs_mem: probe of 9c900000.memory failed with error -22
We should mark SCM properly just like we did for trogdor.
Fixes: 7bd6680b47fa ("Revert "Revert "arm64: dma: Drop cache invalidation from arch_dma_prep_coherent()""")
Fixes: 7a1f4e7f740d ("arm64: dts: qcom: sc7280: Add basic dts/dtsi files for sc7280 soc")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230616081440.v2.4.I21dc14a63327bf81c6bb58fe8ed91dbdc9849ee2@changeid
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Trogdor devices use firmware backed by TF-A instead of Qualcomm's
normal TZ. On TF-A we end up mapping memory as cacheable.
Specifically, you can see in Trogdor's TF-A code [1] in
qti_sip_mem_assign() that we call qti_mmap_add_dynamic_region() with
MT_RO_DATA. This translates down to MT_MEMORY instead of
MT_NON_CACHEABLE or MT_DEVICE. Apparently Qualcomm's normal TZ
implementation maps the memory as non-cacheable.
Let's add the "dma-coherent" attribute to the SCM for trogdor.
Adding "dma-coherent" like this fixes WiFi on sc7180-trogdor
devices. WiFi was broken as of commit 7bd6680b47fa ("Revert "Revert
"arm64: dma: Drop cache invalidation from
arch_dma_prep_coherent()"""). Specifically at bootup we'd get:
qcom_scm firmware:scm: Assign memory protection call failed -22
qcom_rmtfs_mem 94600000.memory: assign memory failed
qcom_rmtfs_mem: probe of 94600000.memory failed with error -22
From discussion on the mailing lists [2] and over IRC [3], it was
determined that we should always have been tagging the SCM as
dma-coherent on trogdor but that the old "invalidate" happened to make
things work most of the time. Tagging it properly like this is a much
more robust solution.
[1] https://chromium.googlesource.com/chromiumos/third_party/arm-trusted-firmware/+/refs/heads/firmware-trogdor-13577.B/plat/qti/common/src/qti_syscall.c
[2] https://lore.kernel.org/r/20230614165904.1.I279773c37e2c1ed8fbb622ca6d1397aea0023526@changeid
[3] https://oftc.irclog.whitequark.org/linux-msm/2023-06-15
Fixes: 7bd6680b47fa ("Revert "Revert "arm64: dma: Drop cache invalidation from arch_dma_prep_coherent()""")
Fixes: 7ec3e67307f8 ("arm64: dts: qcom: sc7180-trogdor: add initial trogdor and lazor dt")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230616081440.v2.3.Ic62daa649b47b656b313551d646c4de9a7da4bd4@changeid
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
sc7180-idp is, for most intents and purposes, a trogdor device.
Specifically, sc7180-idp is designed to run the same style of firmware
as trogdor devices. This can be seen from the fact that IDP has the
same "Reserved memory changes" in its device tree that trogdor has.
Recently it was realized that we need to mark SCM as dma-coherent to
match what trogdor's style of firmware (based on TF-A) does [1]. That
means we need this dma-coherent tag on IDP as well.
Without this, on newer versions of Linux, specifically those with
commit 7bd6680b47fa ("Revert "Revert "arm64: dma: Drop cache
invalidation from arch_dma_prep_coherent()"""), WiFi will fail to
work. At bootup you'll see:
qcom_scm firmware:scm: Assign memory protection call failed -22
qcom_rmtfs_mem 94600000.memory: assign memory failed
qcom_rmtfs_mem: probe of 94600000.memory failed with error -22
[1] https://lore.kernel.org/r/20230615145253.1.Ic62daa649b47b656b313551d646c4de9a7da4bd4@changeid
Fixes: 7bd6680b47fa ("Revert "Revert "arm64: dma: Drop cache invalidation from arch_dma_prep_coherent()""")
Fixes: f5ab220d162c ("arm64: dts: qcom: sc7180: Add remoteproc enablers")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230616081440.v2.2.I3c17d546d553378aa8a0c68c3fe04bccea7cba17@changeid
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Trogdor devices use firmware backed by TF-A instead of Qualcomm's
normal TZ. On TF-A we end up mapping memory as cacheable. Specifically,
you can see in Trogdor's TF-A code [1] in qti_sip_mem_assign() that we
call qti_mmap_add_dynamic_region() with MT_RO_DATA. This translates
down to MT_MEMORY instead of MT_NON_CACHEABLE or MT_DEVICE.
Let's allow devices like trogdor to be described properly by allowing
"dma-coherent" in the SCM node.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230616081440.v2.1.Ie79b5f0ed45739695c9970df121e11d724909157@changeid
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
We run into guest hang in edk2 firmware when KSM is kept as running on
the host. The edk2 firmware is waiting for status 0x80 from QEMU's pflash
device (TYPE_PFLASH_CFI01) during the operation of sector erasing or
buffered write. The status is returned by reading the memory region of
the pflash device and the read request should have been forwarded to QEMU
and emulated by it. Unfortunately, the read request is covered by an
illegal stage2 mapping when the guest hang issue occurs. The read request
is completed with QEMU bypassed and wrong status is fetched. The edk2
firmware runs into an infinite loop with the wrong status.
The illegal stage2 mapping is populated due to same page sharing by KSM
at (C) even the associated memory slot has been marked as invalid at (B)
when the memory slot is requested to be deleted. It's notable that the
active and inactive memory slots can't be swapped when we're in the middle
of kvm_mmu_notifier_change_pte() because kvm->mn_active_invalidate_count
is elevated, and kvm_swap_active_memslots() will busy loop until it reaches
to zero again. Besides, the swapping from the active to the inactive memory
slots is also avoided by holding &kvm->srcu in __kvm_handle_hva_range(),
corresponding to synchronize_srcu_expedited() in kvm_swap_active_memslots().
CPU-A CPU-B
----- -----
ioctl(kvm_fd, KVM_SET_USER_MEMORY_REGION)
kvm_vm_ioctl_set_memory_region
kvm_set_memory_region
__kvm_set_memory_region
kvm_set_memslot(kvm, old, NULL, KVM_MR_DELETE)
kvm_invalidate_memslot
kvm_copy_memslot
kvm_replace_memslot
kvm_swap_active_memslots (A)
kvm_arch_flush_shadow_memslot (B)
same page sharing by KSM
kvm_mmu_notifier_invalidate_range_start
:
kvm_mmu_notifier_change_pte
kvm_handle_hva_range
__kvm_handle_hva_range
kvm_set_spte_gfn (C)
:
kvm_mmu_notifier_invalidate_range_end
Fix the issue by skipping the invalid memory slot at (C) to avoid the
illegal stage2 mapping so that the read request for the pflash's status
is forwarded to QEMU and emulated by it. In this way, the correct pflash's
status can be returned from QEMU to break the infinite loop in the edk2
firmware.
We tried a git-bisect and the first problematic commit is cd4c71835228 ("
KVM: arm64: Convert to the gfn-based MMU notifier callbacks"). With this,
clean_dcache_guest_page() is called after the memory slots are iterated
in kvm_mmu_notifier_change_pte(). clean_dcache_guest_page() is called
before the iteration on the memory slots before this commit. This change
literally enlarges the racy window between kvm_mmu_notifier_change_pte()
and memory slot removal so that we're able to reproduce the issue in a
practical test case. However, the issue exists since commit d5d8184d35c9
("KVM: ARM: Memory virtualization setup").
Cc: stable@vger.kernel.org # v3.9+
Fixes: d5d8184d35c9 ("KVM: ARM: Memory virtualization setup")
Reported-by: Shuai Hu <hshuai@redhat.com>
Reported-by: Zhenyu Zhang <zhenyzha@redhat.com>
Signed-off-by: Gavin Shan <gshan@redhat.com>
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Oliver Upton <oliver.upton@linux.dev>
Reviewed-by: Peter Xu <peterx@redhat.com>
Reviewed-by: Sean Christopherson <seanjc@google.com>
Reviewed-by: Shaoqin Huang <shahuang@redhat.com>
Message-Id: <20230615054259.14911-1-gshan@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This reverts commit 36de5f303ca1bd6fce74815ef17ef3d8ff8737b5.
The commit caused boot failures on some configurations due to cgroup
hierarchies not being created at all.
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
ice_change_mtu() is currently using a separate ice_down() and ice_up()
calls to reflect changed MTU. ice_down_up() serves this purpose, so do
the refactoring here.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
There is no need to use managed memory allocation here. The memory is
released at the end of the function.
Use kzalloc()/kfree() to simplify the code.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The complete profile bit together with the NSTR link pair
present bit indicate whether or not the NSTR bitmap is,
the NSTR bitmap size just indicates how big it is.
Fixes: 7b6f08771bf6 ("wifi: ieee80211: Support validating ML station profile length")
Fixes: 5c1f97537bfb ("wifi: mac80211: store BSS param change count from assoc response")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The BTF_TYPE_SAFE_NESTED macro was replaced by the BTF_TYPE_SAFE_TRUSTED,
BTF_TYPE_SAFE_RCU, and BTF_TYPE_SAFE_RCU_OR_NULL macros. Fix the docs
correspondingly.
Fixes: 6fcd486b3a0a ("bpf: Refactor RCU enforcement in the verifier.")
Signed-off-by: Anton Protopopov <aspsk@isovalent.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20230622095424.1024244-1-aspsk@isovalent.com
|
|
Fix the description of the seq_info field of the bpf_iter_reg structure which
was wrong due to an accidental copy/paste of the previous field's description.
Fixes: 8972e18a439d ("bpf, docs: BPF Iterator Document")
Signed-off-by: Anton Protopopov <aspsk@isovalent.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Yonghong Song <yhs@fb.com>
Link: https://lore.kernel.org/bpf/20230622095407.1024053-1-aspsk@isovalent.com
|
|
We all know they are redundant.
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Michal Wilczynski <michal.wilczynski@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Arpana Arland <arpanax.arland@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The check for existing VFs was redundant since very
inception of SR-IOV sysfs interface in the kernel,
see commit 1789382a72a5 ("PCI: SRIOV control and status via sysfs").
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently ice driver's .ndo_bpf callback brings interface down and up
independently of XDP resources' presence. This is only needed when
either these resources have to be configured or removed. It means that
if one is switching XDP programs on-the-fly with running traffic,
packets will be dropped.
To avoid this, compare early on ice_xdp_setup_prog() state of incoming
bpf_prog pointer vs the bpf_prog pointer that is already assigned to
VSI. Do the swap in case VSI has bpf_prog and incoming one are non-NULL.
Lastly, while at it, put old bpf_prog *after* the update of Rx ring's
bpf_prog pointer. In theory previous code could expose us to a state
where Rx ring's bpf_prog would still be referring to old_prog that got
released with earlier bpf_prog_put().
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Tested-by: Chandan Kumar Rout <chandanx.rout@intel.com> (A Contingent Worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The ice_sq_send_cmd() function is used to send messages to the control
queues used to communicate with firmware, virtual functions, and even some
hardware.
When sending a control queue message, the driver is designed to
synchronously wait for a response from the queue. Currently it waits
between checks for 100 to 150 microseconds.
Commit f86d6f9c49f6 ("ice: sleep, don't busy-wait, for
ICE_CTL_Q_SQ_CMD_TIMEOUT") did recently change the behavior from an
unnecessary delay into a sleep which is a significant improvement over the
old behavior of polling using udelay.
Because of the nature of PCIe transactions, the hardware won't be informed
about a new message until the write to the tail register posts. This is
only guaranteed to occur at the next register read. In ice_sq_send_cmd(),
this happens at the ice_sq_done() call. Because of this, the driver
essentially forces a minimum of one full wait time regardless of how fast
the response is.
For the hardware-based sideband queue, this is especially slow. It is
expected that the hardware will respond within 2 or 3 microseconds, an
order of magnitude faster than the 100-150 microsecond sleep.
Allow such fast completions to occur without delay by introducing a small 5
microsecond delay first before entering the sleeping timeout loop. Ensure
the tail write has been posted by using ice_flush(hw) first.
While at it, lets also remove the ICE_CTL_Q_SQ_CMD_USEC macro as it
obscures the sleep time in the inner loop. It was likely introduced to
avoid "magic numbers", but in practice sleep and delay values are easier to
read and understand when using actual numbers instead of a named constant.
This change should allow the fast hardware based control queue messages to
complete quickly without delay, while slower firmware queue response times
will sleep while waiting for the response.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Michal Schmidt <mschmidt@redhat.com>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
STM32F4-F7 are, from hardware point of view, capable to handle device mode.
So this property should not be forced at false in dt-bindings.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/Message-Id: <20230621115523.923176-3-valentin.caron@foss.st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Make all possible functions static.
Move iavf_force_wb() up to avoid forward declaration.
Suggested-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Remove iavf_aq_get_rss_lut(), iavf_aq_get_rss_key(), iavf_vf_reset().
Remove some "OS specific memory free for shared code" wrappers ;)
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Defer removal of current primary MAC until a replacement is successfully
added. Previous implementation would left filter list with no primary MAC.
This was found while reading the code.
The patch takes advantage of the fact that there can only be a single primary
MAC filter at any time ([1] by Piotr)
Piotr has also applied some review suggestions during our internal patch
submittal process.
[1] https://lore.kernel.org/netdev/20230614145302.902301-2-piotrx.gardocki@intel.com/
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Piotr Gardocki <piotrx.gardocki@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The Dell Studio 1569 predates Windows 8, so it defaults to using
acpi_video# for backlight control, but this is non functional on
this model.
Add a DMI quirk to use the native intel_backlight interface which
does work properly.
Reported-by: raycekarneal <raycekarneal@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
There's an hardware issue that can cause missing timestamps. The bug
is that the interrupt is only cleared if the IGC_TXSTMPH_0 register is
read.
The bug can cause a race condition if a timestamp is captured at the
wrong time, and we will miss that timestamp. To reduce the time window
that the problem is able to happen, in case no timestamp was ready, we
read the "previous" value of the timestamp registers, and we compare
with the "current" one, if it didn't change we can be reasonably sure
that no timestamp was captured. If they are different, we use the new
value as the captured timestamp.
The HW bug is not easy to reproduce, got to reproduce it when smashing
the NIC with timestamping requests from multiple applications (e.g.
multiple ntpperf instances + ptp4l), after 10s of minutes.
This workaround has more impact when multiple timestamp registers are
used, and the IGC_TXSTMPH_0 register always need to be read, so the
interrupt is cleared.
Fixes: 2c344ae24501 ("igc: Add support for TX timestamping")
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When the interrupt is handled, the TXTT_0 bit in the TSYNCTXCTL
register should already be set and the timestamp value already loaded
in the appropriate register.
This simplifies the handling, and reduces the latency for retrieving
the TX timestamp, which increase the amount of TX timestamps that can
be handled in a given time period.
As the "work" function doesn't run in a workqueue anymore, rename it
to something more sensible, a event handler.
Using ntpperf[1] we can see the following performance improvements:
Before:
$ sudo ./ntpperf -i enp3s0 -m 10:22:22:22:22:21 -d 192.168.1.3 -s 172.18.0.0/16 -I -H -o -37
| responses | TX timestamp offset (ns)
rate clients | lost invalid basic xleave | min mean max stddev
1000 100 0.00% 0.00% 0.00% 100.00% -56 +9 +52 19
1500 150 0.00% 0.00% 0.00% 100.00% -40 +30 +75 22
2250 225 0.00% 0.00% 0.00% 100.00% -11 +29 +72 15
3375 337 0.00% 0.00% 0.00% 100.00% -18 +40 +88 22
5062 506 0.00% 0.00% 0.00% 100.00% -19 +23 +77 15
7593 759 0.00% 0.00% 0.00% 100.00% +7 +47 +5168 43
11389 1138 0.00% 0.00% 0.00% 100.00% -11 +41 +5240 39
17083 1708 0.00% 0.00% 0.00% 100.00% +19 +60 +5288 50
25624 2562 0.00% 0.00% 0.00% 100.00% +1 +56 +5368 58
38436 3843 0.00% 0.00% 0.00% 100.00% -84 +12 +8847 66
57654 5765 0.00% 0.00% 100.00% 0.00%
86481 8648 0.00% 0.00% 100.00% 0.00%
129721 12972 0.00% 0.00% 100.00% 0.00%
194581 16384 0.00% 0.00% 100.00% 0.00%
291871 16384 27.35% 0.00% 72.65% 0.00%
437806 16384 50.05% 0.00% 49.95% 0.00%
After:
$ sudo ./ntpperf -i enp3s0 -m 10:22:22:22:22:21 -d 192.168.1.3 -s 172.18.0.0/16 -I -H -o -37
| responses | TX timestamp offset (ns)
rate clients | lost invalid basic xleave | min mean max stddev
1000 100 0.00% 0.00% 0.00% 100.00% -44 +0 +61 19
1500 150 0.00% 0.00% 0.00% 100.00% -6 +39 +81 16
2250 225 0.00% 0.00% 0.00% 100.00% -22 +25 +69 15
3375 337 0.00% 0.00% 0.00% 100.00% -28 +15 +56 14
5062 506 0.00% 0.00% 0.00% 100.00% +7 +78 +143 27
7593 759 0.00% 0.00% 0.00% 100.00% -54 +24 +144 47
11389 1138 0.00% 0.00% 0.00% 100.00% -90 -33 +28 21
17083 1708 0.00% 0.00% 0.00% 100.00% -50 -2 +35 14
25624 2562 0.00% 0.00% 0.00% 100.00% -62 +7 +66 23
38436 3843 0.00% 0.00% 0.00% 100.00% -33 +30 +5395 36
57654 5765 0.00% 0.00% 100.00% 0.00%
86481 8648 0.00% 0.00% 100.00% 0.00%
129721 12972 0.00% 0.00% 100.00% 0.00%
194581 16384 19.50% 0.00% 80.50% 0.00%
291871 16384 35.81% 0.00% 64.19% 0.00%
437806 16384 55.40% 0.00% 44.60% 0.00%
[1] https://github.com/mlichvar/ntpperf
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Before requesting a packet transmission to be hardware timestamped,
check if the user has TX timestamping enabled. Fixes an issue that if
a packet was internally forwarded to the NIC, and it had the
SKBTX_HW_TSTAMP flag set, the driver would mark that timestamp as
skipped.
In reality, that timestamp was "not for us", as TX timestamp could
never be enabled in the NIC.
Checking if the TX timestamping is enabled earlier has a secondary
effect that when TX timestamping is disabled, there's no need to check
for timestamp timeouts.
We should only take care to free any pending timestamp when TX
timestamping is disabled, as that skb would never be released
otherwise.
Fixes: 2c344ae24501 ("igc: Add support for TX timestamping")
Suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently, the igc driver supports timestamping only one tx packet at a
time. During the transmission flow, the skb that requires hardware
timestamping is saved in adapter->ptp_tx_skb. Once hardware has the
timestamp, an interrupt is delivered, and adapter->ptp_tx_work is
scheduled. In igc_ptp_tx_work(), we read the timestamp register, update
adapter->ptp_tx_skb, and notify the network stack.
While the thread executing the transmission flow (the user process
running in kernel mode) and the thread executing ptp_tx_work don't
access adapter->ptp_tx_skb concurrently, there are two other places
where adapter->ptp_tx_skb is accessed: igc_ptp_tx_hang() and
igc_ptp_suspend().
igc_ptp_tx_hang() is executed by the adapter->watchdog_task worker
thread which runs periodically so it is possible we have two threads
accessing ptp_tx_skb at the same time. Consider the following scenario:
right after __IGC_PTP_TX_IN_PROGRESS is set in igc_xmit_frame_ring(),
igc_ptp_tx_hang() is executed. Since adapter->ptp_tx_start hasn't been
written yet, this is considered a timeout and adapter->ptp_tx_skb is
cleaned up.
This patch fixes the issue described above by adding the ptp_tx_lock to
protect access to ptp_tx_skb and ptp_tx_start fields from igc_adapter.
Since igc_xmit_frame_ring() called in atomic context by the networking
stack, ptp_tx_lock is defined as a spinlock, and the irq safe variants
of lock/unlock are used.
With the introduction of the ptp_tx_lock, the __IGC_PTP_TX_IN_PROGRESS
flag doesn't provide much of a use anymore so this patch gets rid of it.
Fixes: 2c344ae24501 ("igc: Add support for TX timestamping")
Signed-off-by: Andre Guedes <andre.guedes@intel.com>
Signed-off-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Reviewed-by: Kurt Kanzenbach <kurt@linutronix.de>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When we didn't find a device and didn't guess it might be a partition,
it might still show up later, so don't disable rootwait for it by
returning -EINVAL.
Fixes: 079caa35f786 ("init: clear root_wait on all invalid root= strings")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20230622150644.600327-1-hch@lst.de
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
There was regression caused by a97699d1d610 ("btrfs: replace
map_lookup->stripe_len by BTRFS_STRIPE_LEN") and supposedly fixed by
a7299a18a179 ("btrfs: fix u32 overflows when left shifting stripe_nr").
To avoid code churn the fix was open coding the type casts but
unfortunately missed one which was still possible to hit [1].
The missing place was assignment of bioc->full_stripe_logical inside
btrfs_map_block().
Fix it by adding a helper that does the safe calculation of the offset
and use it everywhere even though it may not be strictly necessary due
to already using u64 types. This replaces all remaining
"<< BTRFS_STRIPE_LEN_SHIFT" calls.
[1] https://lore.kernel.org/linux-btrfs/20230622065438.86402-1-wqu@suse.com/
Fixes: a7299a18a179 ("btrfs: fix u32 overflows when left shifting stripe_nr")
Signed-off-by: Qu Wenruo <wqu@suse.com>
Reviewed-by: David Sterba <dsterba@suse.com>
[ update changelog ]
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Big transfers might take a bit of time, too constraining timeouts might
lead to false positives. In order to simplify the drivers work and with
the goal of factorizing code in mind, let's add a helper that can be
used by any spi controller driver to derive a relevant per-transfer
timeout value.
The logic is simple: we know how much time it would take to transfer a
byte, we can easily derive the total theoretical amount of time involved
for each transfer. We multiply it by two to have a bit of margin and
enforce a minimum of 500ms.
Suggested-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/r/Message-Id: <20230622090634.3411468-2-miquel.raynal@bootlin.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch fixes a spectre-v1 gadget in cdrom.
The gadget could be triggered by speculatively
bypassing the cdi->capacity check.
Signed-off-by: Jordy Zomer <jordyzomer@google.com>
Link: https://lore.kernel.org/all/20230612110040.849318-2-jordyzomer@google.com
Reviewed-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/all/ZI1+1OG9Ut1MqsUC@equinox
Signed-off-by: Phillip Potter <phil@philpotter.co.uk>
Link: https://lore.kernel.org/r/20230617113828.1230-2-phil@philpotter.co.uk
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
When __blkcg_rstat_flush() is called from cgroup_rstat_flush*() code
path, interrupt is always disabled.
When we start to flush blkcg per-cpu stats list in __blkg_release()
for avoiding to leak blkcg_gq's reference in commit 20cb1c2fb756
("blk-cgroup: Flush stats before releasing blkcg_gq"), local irq
isn't disabled yet, then lockdep warning may be triggered because
the dependent cgroup locks may be acquired from irq(soft irq) handler.
Fix the issue by disabling local irq always.
Fixes: 20cb1c2fb756 ("blk-cgroup: Flush stats before releasing blkcg_gq")
Reported-by: Shinichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Closes: https://lore.kernel.org/linux-block/pz2wzwnmn5tk3pwpskmjhli6g3qly7eoknilb26of376c7kwxy@qydzpvt6zpis/T/#u
Cc: stable@vger.kernel.org
Cc: Jay Shin <jaeshin@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Waiman Long <longman@redhat.com>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Waiman Long <longman@redhat.com>
Link: https://lore.kernel.org/r/20230622084249.1208005-1-ming.lei@redhat.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
