| Age | Commit message (Collapse) | Author |
|---|
|
This patch is similar to the last patch to delay the
pci_alloc_irq_vectors() call in the AER path until after calling
bnxt_reserve_rings(). bnxt_reserve_rings() needs to properly map
the MSIX table first before we call pci_alloc_irq_vectors() which
may immediately write to the MSIX table in some architectures.
Move the bnxt_init_int_mode() call from bnxt_io_slot_reset() to
bnxt_io_resume() after calling bnxt_reserve_rings().
With this change, the AER path may call bnxt_open() ->
bnxt_hwrm_if_change() with bp->irq_tbl set to NULL. bp->irq_tbl is
cleared when we call bnxt_clear_int_mode() in bnxt_io_slot_reset().
So we cannot use !bp->irq_tbl to detect aborted FW reset. Add a
new BNXT_FW_RESET_STATE_ABORT to detect aborted FW reset in
bnxt_hwrm_if_change().
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some architectures (e.g. ARM), calling pci_alloc_irq_vectors()
will immediately cause the MSIX table to be written. This will not
work if we haven't called bnxt_reserve_rings() to properly map
the MSIX table to the MSIX vectors reserved by FW.
Fix the FW error recovery path to delay the bnxt_init_int_mode() ->
pci_alloc_irq_vectors() call by removing it from bnxt_hwrm_if_change().
bnxt_request_irq() later in the code path will call it and by then the
MSIX table is properly mapped.
Fixes: 4343838ca5eb ("bnxt_en: Replace deprecated PCI MSIX APIs")
Suggested-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If bnxt_rx_vlan() fails because the VLAN protocol ID is invalid,
the SKB is freed but we're missing the call to recycle it. This
may cause the warning:
"page_pool_release_retry() stalled pool shutdown"
Add the missing skb_mark_for_recycle() in bnxt_rx_vlan().
Fixes: 86b05508f775 ("bnxt_en: Use the unified RX page pool buffers for XDP and non-XDP")
Reviewed-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When RDMA driver is loaded, running offline self test is not
supported and driver returns failure early. But it is not clearing
the input buffer and hence the application prints some junk
characters for individual test results.
Fix it by clearing the buffer before returning.
Fixes: 895621f1c816 ("bnxt_en: Don't support offline self test when RoCE driver is loaded")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
WARN_ON() is triggered in __flush_work() if bnxt_init_chip() fails
because we call cancel_work_sync() on dim work that has not been
initialized.
WARNING: CPU: 37 PID: 5223 at kernel/workqueue.c:4201 __flush_work.isra.0+0x212/0x230
The driver relies on the BNXT_STATE_NAPI_DISABLED bit to check if dim
work has already been cancelled. But in the bnxt_open() path,
BNXT_STATE_NAPI_DISABLED is not set and this causes the error
path to think that it needs to cancel the uninitalized dim work.
Fix it by setting BNXT_STATE_NAPI_DISABLED during initialization.
The bit will be cleared when we enable NAPI and initialize dim work.
Fixes: 40452969a506 ("bnxt_en: Fix DIM shutdown")
Suggested-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Shravya KN <shravya.k-n@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When generating the MSR_IA32_PEBS_ENABLE value that will be loaded on
VM-Entry to a KVM guest, mask the value with the vCPU's desired PEBS_ENABLE
value. Consulting only the host kernel's host vs. guest masks results in
running the guest with PEBS enabled even when the guest doesn't want to use
PEBS. Because KVM uses perf events to proxy the guest virtual PMU, simply
looking at exclude_host can't differentiate between events created by host
userspace, and events created by KVM on behalf of the guest.
Running the guest with PEBS unexpectedly enabled typically manifests as
crashes due to a near-infinite stream of #PFs. E.g. if the guest hasn't
written MSR_IA32_DS_AREA, the CPU will hit page faults on address '0' when
trying to record PEBS events.
The issue is most easily reproduced by running `perf kvm top` from before
commit 7b100989b4f6 ("perf evlist: Remove __evlist__add_default") (after
which, `perf kvm top` effectively stopped using PEBS). The userspace side
of perf creates a guest-only PEBS event, which intel_guest_get_msrs()
misconstrues a guest-*owned* PEBS event.
Arguably, this is a userspace bug, as enabling PEBS on guest-only events
simply cannot work, and userspace can kill VMs in many other ways (there
is no danger to the host). However, even if this is considered to be bad
userspace behavior, there's zero downside to perf/KVM restricting PEBS to
guest-owned events.
Note, commit 854250329c02 ("KVM: x86/pmu: Disable guest PEBS temporarily
in two rare situations") fixed the case where host userspace is profiling
KVM *and* userspace, but missed the case where userspace is profiling only
KVM.
Fixes: c59a1f106f5c ("KVM: x86/pmu: Add IA32_PEBS_ENABLE MSR emulation for extended PEBS")
Closes: https://lore.kernel.org/all/Z_VUswFkWiTYI0eD@do-x1carbon
Reported-by: Seth Forshee <sforshee@kernel.org>
Signed-off-by: Sean Christopherson <seanjc@google.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Dapeng Mi <dapeng1.mi@linux.intel.com>
Tested-by: "Seth Forshee (DigitalOcean)" <sforshee@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250426001355.1026530-1-seanjc@google.com
|
|
Shannon Nelson says:
====================
pds_core: small code updates
These are a few little code touch ups for a kdoc complaint,
quicker error detection, and a cleaner initialization.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Initialize the .enabled field of the FWCTL viftype default in
the declaration rather than as a bit of code as it is always
to be enabled and needs no logic around it.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Shorten the adminq poll starting interval in order to notice
any transaction errors more quickly.
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the kernel-doc complaint
include/linux/pds/pds_adminq.h:481: warning: Excess struct member 'name' description in 'pds_core_lif_getattr_comp'
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Shannon Nelson <shannon.nelson@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mutex unlock for vdev->submitted_jobs_lock was incorrectly placed
before unlocking file_priv->lock. Change order of unlocks to avoid potential
race conditions.
Fixes: 5bbccadaf33e ("accel/ivpu: Abort all jobs after command queue unregister")
Signed-off-by: Karol Wachowski <karol.wachowski@intel.com>
Reviewed-by: Jeff Hugo <jeff.hugo@oss.qualcomm.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://lore.kernel.org/r/20250425093656.2228168-1-jacek.lawrynowicz@linux.intel.com
|
|
Fix deadlocks in ivpu_cmdq_create_ioctl() and ivpu_cmdq_destroy_ioctl()
related to runtime suspend.
Runtime suspend acquires file_priv->lock mutex by calling
ivpu_cmdq_reset_all_contexts(). The same lock is acquired in the cmdq
ioctls. If one of the cmdq ioctls is called while runtime suspend is in
progress, it can lead to a deadlock.
Call stacks from example deadlock below.
Runtime suspend thread:
[ 3443.179717] Call Trace:
[ 3443.179724] __schedule+0x4b6/0x16b0
[ 3443.179732] ? __mod_timer+0x27d/0x3a0
[ 3443.179738] schedule+0x2f/0x140
[ 3443.179741] schedule_preempt_disabled+0x19/0x30
[ 3443.179743] __mutex_lock.constprop.0+0x335/0x7d0
[ 3443.179745] ? xas_find+0x1ed/0x260
[ 3443.179747] ? xa_find+0x8e/0xf0
[ 3443.179749] __mutex_lock_slowpath+0x13/0x20
[ 3443.179751] mutex_lock+0x41/0x60
[ 3443.179757] ivpu_cmdq_reset_all_contexts+0x82/0x150 [intel_vpu a9bd091a97f28f0235f161316b29f8234f437295]
[ 3443.179786] ivpu_pm_runtime_suspend_cb+0x1f1/0x3f0 [intel_vpu a9bd091a97f28f0235f161316b29f8234f437295]
[ 3443.179850] pci_pm_runtime_suspend+0x6e/0x1f0
[ 3443.179870] ? __pfx_pci_pm_runtime_suspend+0x10/0x10
[ 3443.179886] __rpm_callback+0x48/0x130
[ 3443.179899] rpm_callback+0x64/0x70
[ 3443.179911] rpm_suspend+0x12c/0x630
[ 3443.179922] ? __schedule+0x4be/0x16b0
[ 3443.179941] pm_runtime_work+0xca/0xf0
[ 3443.179955] process_one_work+0x188/0x3d0
[ 3443.179971] worker_thread+0x2b9/0x3c0
[ 3443.179984] kthread+0xfb/0x220
[ 3443.180001] ? __pfx_worker_thread+0x10/0x10
[ 3443.180013] ? __pfx_kthread+0x10/0x10
[ 3443.180029] ret_from_fork+0x47/0x70
[ 3443.180044] ? __pfx_kthread+0x10/0x10
[ 3443.180059] ret_from_fork_asm+0x1a/0x30
User space thread:
[ 3443.180128] Call Trace:
[ 3443.180138] __schedule+0x4b6/0x16b0
[ 3443.180159] schedule+0x2f/0x140
[ 3443.180163] rpm_resume+0x1a7/0x6a0
[ 3443.180165] ? __pfx_autoremove_wake_function+0x10/0x10
[ 3443.180169] __pm_runtime_resume+0x56/0x90
[ 3443.180171] ivpu_rpm_get+0x28/0xb0 [intel_vpu a9bd091a97f28f0235f161316b29f8234f437295]
[ 3443.180181] ivpu_ipc_send_receive+0x6d/0x120 [intel_vpu a9bd091a97f28f0235f161316b29f8234f437295]
[ 3443.180193] ? free_frozen_pages+0x395/0x670
[ 3443.180199] ? __free_pages+0xa7/0xc0
[ 3443.180202] ivpu_jsm_hws_destroy_cmdq+0x76/0xf0 [intel_vpu a9bd091a97f28f0235f161316b29f8234f437295]
[ 3443.180213] ? locks_dispose_list+0x6c/0xa0
[ 3443.180219] ? kmem_cache_free+0x342/0x470
[ 3443.180222] ? vm_area_free+0x19/0x30
[ 3443.180225] ? xas_load+0x17/0xf0
[ 3443.180229] ? xa_load+0x72/0xb0
[ 3443.180230] ivpu_cmdq_unregister.isra.0+0xb1/0x100 [intel_vpu a9bd091a97f28f0235f161316b29f8234f437295]
[ 3443.180241] ivpu_cmdq_destroy_ioctl+0x8d/0x130 [intel_vpu a9bd091a97f28f0235f161316b29f8234f437295]
[ 3443.180251] ? __pfx_ivpu_cmdq_destroy_ioctl+0x10/0x10 [intel_vpu a9bd091a97f28f0235f161316b29f8234f437295]
[ 3443.180260] drm_ioctl_kernel+0xb3/0x110
[ 3443.180265] drm_ioctl+0x2ca/0x580
[ 3443.180266] ? __pfx_ivpu_cmdq_destroy_ioctl+0x10/0x10 [intel_vpu a9bd091a97f28f0235f161316b29f8234f437295]
[ 3443.180275] ? __fput+0x1ae/0x2f0
[ 3443.180279] ? kmem_cache_free+0x342/0x470
[ 3443.180282] __x64_sys_ioctl+0xa9/0xe0
[ 3443.180286] x64_sys_call+0x13b7/0x26f0
[ 3443.180289] do_syscall_64+0x62/0x180
[ 3443.180291] entry_SYSCALL_64_after_hwframe+0x71/0x79
Fixes: 465a3914b254 ("accel/ivpu: Add API for command queue create/destroy/submit")
Reviewed-by: Jeff Hugo <jeff.hugo@oss.qualcomm.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://lore.kernel.org/r/20250425093341.2202895-1-jacek.lawrynowicz@linux.intel.com
|
|
Increase JMS message state dump command timeout to 100 ms. On some
platforms, the FW may take a bit longer than 50 ms to dump its state
to the log buffer and we don't want to miss any debug info during TDR.
Fixes: 5e162f872d7a ("accel/ivpu: Add FW state dump on TDR")
Cc: stable@vger.kernel.org # v6.13+
Reviewed-by: Jeff Hugo <jeff.hugo@oss.qualcomm.com>
Signed-off-by: Jacek Lawrynowicz <jacek.lawrynowicz@linux.intel.com>
Link: https://lore.kernel.org/r/20250425092822.2194465-1-jacek.lawrynowicz@linux.intel.com
|
|
The "snps,data-width" property[1] defines the AXI data width of the DMA
controller as:
width = 8 × (2^n) bits
(0 = 8 bits, 1 = 16 bits, 2 = 32 bits, ..., 6 = 512 bits)
where "n" is the value of "snps,data-width".
For the CV18xx DMA controller, the correct AXI data width is 32 bits,
corresponding to "snps,data-width = 2".
Test results on Milkv Duo S can be found here [2].
Link: https://github.com/torvalds/linux/blob/master/Documentation/devicetree/bindings/dma/snps%2Cdw-axi-dmac.yaml#L74 [1]
Link: https://gist.github.com/Sutter099/4fa99bb2d89e5af975983124704b3861 [2]
Fixes: 514951a81a5e ("riscv: dts: sophgo: cv18xx: add DMA controller")
Co-developed-by: Yu Yuan <yu.yuan@sjtu.edu.cn>
Signed-off-by: Yu Yuan <yu.yuan@sjtu.edu.cn>
Signed-off-by: Ze Huang <huangze@whut.edu.cn>
Link: https://lore.kernel.org/r/20250428-duo-dma-config-v1-1-eb6ad836ca42@whut.edu.cn
Signed-off-by: Inochi Amaoto <inochiama@gmail.com>
Signed-off-by: Chen Wang <unicorn_wang@outlook.com>
Signed-off-by: Chen Wang <wangchen20@iscas.ac.cn>
|
|
A few ASUS models use the ALC256_FIXUP_ASUS_HEADSET_MODE although they
have no built-in mic pin on NID 0x13, as found in the commit
c1732ede5e80 ("ALSA: hda/realtek - Fix headset and mic on several Asus
laptops with ALC256"). This was relatively harmless in the past as
NID 0x13 was assigned as the secondary mic. But since the fix for the
pin sort order, this pin became the primary one, hence user started
noticing the broken input, and we've fixed already for a few ASUS
models to switch to ALC256_FIXUP_ASUS_MIC_NO_PRESENCE.
This patch corrects the other ASUS models to use the right quirk entry
for fixing the built-in mic regression. Here we cover X541SA
(1043:12e0), X541UV (1043:12f0), Z550SA (1043:13bf0) and X555UB
(1043:1ccd).
Fixes: 3b4309546b48 ("ALSA: hda: Fix headset detection failure due to unstable sort")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=220058
Link: https://patch.msgid.link/20250430053210.31776-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Opt_err is not used in EROFS, we can remove it.
Signed-off-by: Hongbo Li <lihongbo22@huawei.com>
Reviewed-by: Gao Xiang <xiang@kernel.org>
Link: https://lore.kernel.org/r/20250429075056.689570-1-lihongbo22@huawei.com
Signed-off-by: Gao Xiang <xiang@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fix from Herbert Xu:
"This fixes a regression in scompress"
* tag 'v6.15-p6' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: scompress - increment scomp_scratch_users when already allocated
|
|
The precomputed value for the NAND_READ_LOCATION_2 register should be
stored in 'snandc->regs->read_location2'.
Fix the qcom_spi_set_read_loc_first() function accordingly.
Fixes: 7304d1909080 ("spi: spi-qpic: add driver for QCOM SPI NAND flash Interface")
Signed-off-by: Gabor Juhos <j4g8y7@gmail.com>
Reviewed-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Link: https://patch.msgid.link/20250428-qpic-snand-readloc2-fix-v1-1-50ce0877ff72@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Depending on the architecture __ffs() returns either an 'unsigned long'
or 'unsigned int' result. Compile-testing this driver on targets that
use the latter produces a warning:
sound/soc/intel/catpt/dsp.c: In function 'catpt_dsp_set_srampge':
sound/soc/intel/catpt/dsp.c:181:44: error: format '%ld' expects argument of type 'long int', but argument 4 has type 'u32' {aka 'unsigned int'} [-Werror=format=]
181 | dev_dbg(cdev->dev, "sanitize block %ld: off 0x%08x\n",
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Change the type of the local variable to match the format string and
avoid the warning on any architecture.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://patch.msgid.link/20250429073545.3558494-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next
Pablo Neira Ayuso says:
====================
Netfilter updates for net-next
The following batch contains Netfilter updates for net-next:
1) Replace msecs_to_jiffies() by secs_to_jiffies(), from Easwar Hariharan.
2) Allow to compile xt_cgroup with cgroupsv2 support only,
from Michal Koutny.
3) Prepare for sock_cgroup_classid() removal by wrapping it around
ifdef, also from Michal Koutny.
4) Remove redundant pointer fetch on conntrack template, from Xuanqiang Luo.
5) Re-format one block in the tproxy documentation for consistency,
from Chen Linxuan.
6) Expose set element count and type via netlink attributes,
from Florian Westphal.
* tag 'nf-next-25-04-29' of git://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf-next:
netfilter: nf_tables: export set count and backend name to userspace
docs: tproxy: fix formatting for nft code block
netfilter: conntrack: Remove redundant NFCT_ALIGN call
net: cgroup: Guard users of sock_cgroup_classid()
netfilter: xt_cgroup: Make it independent from net_cls
netfilter: xt_IDLETIMER: convert timeouts to secs_to_jiffies()
====================
Link: https://patch.msgid.link/20250428221254.3853-1-pablo@netfilter.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove code that isn't reached. There is no need to check for
adapter->req_vec_chunks, because if it isn't set idpf_set_mb_vec_id()
won't be called.
Only one path when idpf_set_mb_vec_id() is called:
idpf_intr_req()
-> idpf_send_alloc_vectors_msg() -> adapter->req_vec_chunk is allocated
here, otherwise an error is returned and idpf_intr_req() exits with an
error.
The idpf_set_mb_vec_id() becomes one-liner and it is called only once.
Remove it and set mailbox vector index directly.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Reviewed-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
replaces formmated with formatted
also corrects grammar by replacing a with an, and capitalises RST
Signed-off-by: Ruben Wauters <rubenru09@aol.com>
Reviewed-by: Donald Hunter <donald.hunter@gmail.com>
Link: https://patch.msgid.link/20250428215541.6029-1-rubenru09@aol.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Assign the ptype extracted from qword to the ptype field of struct
libeth_rqe_info.
Remove the now excess ptype param of idpf_rx_singleq_extract_fields(),
idpf_rx_singleq_extract_base_fields() and
idpf_rx_singleq_extract_flex_fields().
Suggested-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Mateusz Polchlopek <mateusz.polchlopek@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Provide support for the following devlink cmds:
-DEVLINK_CMD_REGION_GET
-DEVLINK_CMD_REGION_NEW
-DEVLINK_CMD_REGION_DEL
-DEVLINK_CMD_REGION_READ
ixgbe devlink region implementation, similarly to the ice one,
lets user to create snapshots of content of Non Volatile Memory,
content of Shadow RAM, and capabilities of the device.
For both NVM and SRAM regions provide .read() handler to let user
read their contents without the need to create full snapshots.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Slawomir Mrozowicz <slawomirx.mrozowicz@intel.com>
Co-developed-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Tested-by: Bharath R <bharath.r@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Legacy implementation of .set_phys_id() ethtool callback is not
applicable for E610 device.
Add new implementation which uses 0x06E9 command by calling
ixgbe_aci_set_port_id_led().
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Bharath R <bharath.r@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
E610 device doesn't support disabling FC autonegotiation.
Create dedicated E610 .set_pauseparam() implementation and assign
it to ixgbe_ethtool_ops_e610.
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Bharath R <bharath.r@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Currently only APM (Advanced Power Management) is supported by
the ixgbe driver. It works for magic packets only, as for different
sources of wake-up E610 adapter utilizes different feature.
Add E610 specific implementation of ixgbe_set_wol() callback. When
any of broadcast/multicast/unicast wake-up is set, disable APM and
configure ACPI (Advanced Configuration and Power Interface).
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Bharath R <bharath.r@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
E610's implementation of various ethtool ops is different than
the ones corresponding to ixgbe legacy products. Therefore create
separate E610 ethtool_ops struct which will be filled out in the
forthcoming patches.
Add adequate ops struct basing on MAC type. This step requires
changing a bit the flow of probing by placing ixgbe_set_ethtool_ops
after hw.mac.type is assigned. So move the whole netdev assignment
block after hw.mac.type is known. This step doesn't have any additional
impact on probing sequence.
Suggested-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Jedrzej Jagielski <jedrzej.jagielski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Bharath R <bharath.r@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
The current MQPRIO offload implementation uses the legacy TSN Tx mode. In
this mode the hardware uses four packet buffers and considers queue
priorities.
In order to harmonize the TAPRIO implementation with MQPRIO, switch to the
regular TSN Tx mode. This mode also uses four packet buffers and considers
queue priorities. In addition to the legacy mode, transmission is always
coupled to Qbv. The driver already has mechanisms to use a dummy schedule
of 1 second with all gates open for ETF. Simply use this for MQPRIO too.
This reduces code and makes it easier to add support for frame preemption
later.
Tested on i225 with real time application using high priority queue, iperf3
using low priority queue and network TAP device.
Acked-by: Faizal Rahim <faizal.abdul.rahim@linux.intel.com>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Limit netdev_tc calls to MQPRIO. Currently these calls are made in
igc_tsn_enable_offload() and igc_tsn_disable_offload() which are used by
TAPRIO and ETF as well. However, these are only required for MQPRIO.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
When running the igc with XDP/ZC in busy polling mode with deferral of hard
interrupts, interrupts still happen from time to time. That is caused by
the igb task watchdog which triggers Rx interrupts periodically.
That mechanism has been introduced to overcome skb/memory allocation
failures [1]. So the Rx clean functions stop processing the Rx ring in case
of such failure. The task watchdog triggers Rx interrupts periodically in
the hope that memory became available in the mean time.
The current behavior is undesirable for real time applications, because the
driver induced Rx interrupts trigger also the softirq processing. However,
all real time packets should be processed by the application which uses the
busy polling method.
Therefore, only trigger the Rx interrupts in case of real allocation
failures. Introduce a new flag for signaling that condition.
Follow the same logic as in commit 8dcf2c212078 ("igc: Get rid of spurious
interrupts").
[1] - https://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git/commit/?id=3be507547e6177e5c808544bd6a2efa2c7f1d436
Reviewed-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Sweta Kumari <sweta.kumari@intel.com>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Use netif_napi_add_config() to assign persistent per-NAPI config.
This is useful for preserving NAPI settings when changing queue counts or
for user space programs using SO_INCOMING_NAPI_ID.
Reviewed-by: Joe Damato <jdamato@fastly.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Link queues to NAPI instances via netdev-genl API. This is required to use
XDP/ZC busy polling. See commit 5ef44b3cb43b ("xsk: Bring back busy polling
support") for details.
This also allows users to query the info with netlink:
|$ ./tools/net/ynl/pyynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
| --dump queue-get --json='{"ifindex": 2}'
|[{'id': 0, 'ifindex': 2, 'napi-id': 8201, 'type': 'rx'},
| {'id': 1, 'ifindex': 2, 'napi-id': 8202, 'type': 'rx'},
| {'id': 2, 'ifindex': 2, 'napi-id': 8203, 'type': 'rx'},
| {'id': 3, 'ifindex': 2, 'napi-id': 8204, 'type': 'rx'},
| {'id': 0, 'ifindex': 2, 'napi-id': 8201, 'type': 'tx'},
| {'id': 1, 'ifindex': 2, 'napi-id': 8202, 'type': 'tx'},
| {'id': 2, 'ifindex': 2, 'napi-id': 8203, 'type': 'tx'},
| {'id': 3, 'ifindex': 2, 'napi-id': 8204, 'type': 'tx'}]
Add rtnl locking to PCI error handlers, because netif_queue_set_napi()
requires the lock held.
While at __igb_open() use RCT coding style.
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: Joe Damato <jdamato@fastly.com>
Tested-by: Sweta Kumari <sweta.kumari@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Link IRQs to NAPI instances via netdev-genl API. This allows users to query
that information via netlink:
|$ ./tools/net/ynl/pyynl/cli.py --spec Documentation/netlink/specs/netdev.yaml \
| --dump napi-get --json='{"ifindex": 2}'
|[{'defer-hard-irqs': 0,
| 'gro-flush-timeout': 0,
| 'id': 8204,
| 'ifindex': 2,
| 'irq': 127,
| 'irq-suspend-timeout': 0},
| {'defer-hard-irqs': 0,
| 'gro-flush-timeout': 0,
| 'id': 8203,
| 'ifindex': 2,
| 'irq': 126,
| 'irq-suspend-timeout': 0},
| {'defer-hard-irqs': 0,
| 'gro-flush-timeout': 0,
| 'id': 8202,
| 'ifindex': 2,
| 'irq': 125,
| 'irq-suspend-timeout': 0},
| {'defer-hard-irqs': 0,
| 'gro-flush-timeout': 0,
| 'id': 8201,
| 'ifindex': 2,
| 'irq': 124,
| 'irq-suspend-timeout': 0}]
|$ cat /proc/interrupts | grep enp2s0
|123: 0 1 IR-PCI-MSIX-0000:02:00.0 0-edge enp2s0
|124: 0 7 IR-PCI-MSIX-0000:02:00.0 1-edge enp2s0-TxRx-0
|125: 0 0 IR-PCI-MSIX-0000:02:00.0 2-edge enp2s0-TxRx-1
|126: 0 5 IR-PCI-MSIX-0000:02:00.0 3-edge enp2s0-TxRx-2
|127: 0 0 IR-PCI-MSIX-0000:02:00.0 4-edge enp2s0-TxRx-3
Reviewed-by: Joe Damato <jdamato@fastly.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Comment was erroneously added with /**, amend this to use /* as it is
not a kernel-doc.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202504262247.1UBrDBVN-lkp@intel.com/
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250428214920.813038-1-aryan.srivastava@alliedtelesis.co.nz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If any address or port is changed, update it in all packets and recalculate
checksum.
Fixes: 9fd1ff5d2ac7 ("udp: Support UDP fraglist GRO/GSO.")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Reviewed-by: Willem de Bruijn <willemb@google.com>
Link: https://patch.msgid.link/20250426153210.14044-1-nbd@nbd.name
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Vladimir Oltean says:
====================
Fix Felix DSA taprio gates after clock jump
Richie Pearn presented a reproducible situation where traffic would get
blocked on the NXP LS1028A switch if a certain taprio schedule was
applied, and stepping the PTP clock would take place. The latter event
is an expected initial occurrence, but also at runtime, for example when
transitioning from one grandmaster to another.
The issue is completely described in patch 1/4, which also contains
the fix, but it has left me with some doubts regarding the need for
vsc9959_tas_clock_adjust() in general.
In order to prove to myself that vsc9959_tas_clock_adjust() is needed in
general, I have written a selftest for the tc-taprio data path in patch
4/4. On the LS1028A, we can clearly see the following failures without
that function:
INFO: Forcing a backward clock jump
TEST: ping [FAIL]
INFO: Setting up taprio after PTP
TEST: In band with gate [FAIL]
Reception of 100 packets failed
TEST: Out of band with gate [FAIL]
Reception of 100 packets failed
As for testing my fix from patch 1/4, that was quite a bit more complex
to do automatically. In fact, I couldn't find any other schedule that
would fail to be updated by vsc9959_tas_clock_adjust() as cleanly as
the schedule from Richie, so I've added that specific schedule as the
test_clock_jump_backward() test.
The test ordering is also (unfortunately) very strategic. Running the
selftest to the end dirties the GCL RAM, and when running
test_clock_jump_backward() once again, the GCL entries won't be all
zeroes as they were the first time around. They will contain bits and
pieces of old schedules, making it very challenging to make it fail.
Thus, test_clock_jump_backward() is the first in the test suite, and
without patch 1/4, it is only supposed to fail the _first_ time when
running after a clean boot.
====================
Link: https://patch.msgid.link/20250426144859.3128352-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add a forwarding path test for tc-taprio, based on isochron. This is
specifically intended for NICs with an offloaded data path (switchdev/DSA)
and requires taprio 'flags 2'. Also, $h1 and $h2 must support hardware
timestamping, and $h1 tc-etf offload, for isochron to work.
Packets received by a switch while the egress port has a taprio schedule
with an open gate for the traffic class must be sent right away.
Packets received by the switch while the traffic class gate must be
delayed until it opens.
Packets received by the switch must be dropped if the gate for the
traffic class never opens.
Packets should pass if the maximum SDU for the traffic class allows it,
and should be dropped otherwise.
The schedule should auto-update itself if clock jumps take place while
taprio is installed. Repeat most of the above tests after forcing two
clock jumps, one backwards (in Jan 1970) and one back into the present.
Symlink it from tools/testing/selftests/drivers/net/dsa, because usually
DSA ports have the same MAC address, and we need STABLE_MAC_ADDRS=yes
from its forwarding.config for the test to run successfully.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250426144859.3128352-5-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Make out-of-band testing (send a packet when its traffic class gate is
closed, expecting it to be delayed) more predictable by allowing the
window size to be customized by isochron_do().
From man isochron-send, the window size alters the advance time (the
delta between the transmission time of the packet, and its expected TX
time when using SO_TXTIME or tc-taprio on the sender). In absence of the
argument, isochron-send defaults to maximizing the advance time (making
it equal to the cycle length).
The default behavior is exactly what is problematic. An advance time
that is too large will make packets intended to be out-of-band still be
potentially in-band with an open gate from the schedule's previous cycle.
We need to allow that advance time to be reduced.
Perhaps a bit confusingly, isochron_do() has a shift_time argument
currently, but that does not help here. The shift time shifts both the
user space wakeup time and the expected TX time by equal amounts, it is
unable of bringing them closer to one another.
Set the window size properly for the Ocelot PSFP selftest as well.
That used to work due to a very carefully chosen SHIFT_TIME_NS.
I've re-tested that the test still works properly.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250426144859.3128352-4-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This snippet will be necessary for a future isochron-based test, so
provide a simpler high-level interface for counting the received
packets.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250426144859.3128352-3-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Simplest setup to reproduce the issue: connect 2 ports of the
LS1028A-RDB together (eno0 with swp0) and run:
$ ip link set eno0 up && ip link set swp0 up
$ tc qdisc replace dev swp0 parent root handle 100 taprio num_tc 8 \
queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 map 0 1 2 3 4 5 6 7 \
base-time 0 sched-entry S 20 300000 sched-entry S 10 200000 \
sched-entry S 20 300000 sched-entry S 48 200000 \
sched-entry S 20 300000 sched-entry S 83 200000 \
sched-entry S 40 300000 sched-entry S 00 200000 flags 2
$ ptp4l -i eno0 -f /etc/linuxptp/configs/gPTP.cfg -m &
$ ptp4l -i swp0 -f /etc/linuxptp/configs/gPTP.cfg -m
One will observe that the PTP state machine on swp0 starts
synchronizing, then it attempts to do a clock step, and after that, it
never fails to recover from the condition below.
ptp4l[82.427]: selected best master clock 00049f.fffe.05f627
ptp4l[82.428]: port 1 (swp0): MASTER to UNCALIBRATED on RS_SLAVE
ptp4l[83.252]: port 1 (swp0): UNCALIBRATED to SLAVE on MASTER_CLOCK_SELECTED
ptp4l[83.886]: rms 4537731277 max 9075462553 freq -18518 +/- 11467 delay 818 +/- 0
ptp4l[84.170]: timed out while polling for tx timestamp
ptp4l[84.171]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[84.172]: port 1 (swp0): send peer delay request failed
ptp4l[84.173]: port 1 (swp0): clearing fault immediately
ptp4l[84.269]: port 1 (swp0): SLAVE to LISTENING on INIT_COMPLETE
ptp4l[85.303]: timed out while polling for tx timestamp
ptp4l[84.171]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[84.172]: port 1 (swp0): send peer delay request failed
ptp4l[84.173]: port 1 (swp0): clearing fault immediately
ptp4l[84.269]: port 1 (swp0): SLAVE to LISTENING on INIT_COMPLETE
ptp4l[85.303]: timed out while polling for tx timestamp
ptp4l[85.304]: increasing tx_timestamp_timeout or increasing kworker priority may correct this issue, but a driver bug likely causes it
ptp4l[85.305]: port 1 (swp0): send peer delay response failed
ptp4l[85.306]: port 1 (swp0): clearing fault immediately
ptp4l[86.304]: timed out while polling for tx timestamp
A hint is given by the non-zero statistics for dropped packets which
were expecting hardware TX timestamps:
$ ethtool --include-statistics -T swp0
(...)
Statistics:
tx_pkts: 30
tx_lost: 11
tx_err: 0
We know that when PTP clock stepping takes place (from ocelot_ptp_settime64()
or from ocelot_ptp_adjtime()), vsc9959_tas_clock_adjust() is called.
Another interesting hint is that placing an early return in
vsc9959_tas_clock_adjust(), so as to neutralize this function, fixes the
issue and TX timestamps are no longer dropped.
The debugging function written by me and included below is intended to
read the GCL RAM, after the admin schedule became operational, through
the two status registers available for this purpose:
QSYS_GCL_STATUS_REG_1 and QSYS_GCL_STATUS_REG_2.
static void vsc9959_print_tas_gcl(struct ocelot *ocelot)
{
u32 val, list_length, interval, gate_state;
int i, err;
err = read_poll_timeout(ocelot_read, val,
!(val & QSYS_PARAM_STATUS_REG_8_CONFIG_PENDING),
10, 100000, false, ocelot, QSYS_PARAM_STATUS_REG_8);
if (err) {
dev_err(ocelot->dev,
"Failed to wait for TAS config pending bit to clear: %pe\n",
ERR_PTR(err));
return;
}
val = ocelot_read(ocelot, QSYS_PARAM_STATUS_REG_3);
list_length = QSYS_PARAM_STATUS_REG_3_LIST_LENGTH_X(val);
dev_info(ocelot->dev, "GCL length: %u\n", list_length);
for (i = 0; i < list_length; i++) {
ocelot_rmw(ocelot,
QSYS_GCL_STATUS_REG_1_GCL_ENTRY_NUM(i),
QSYS_GCL_STATUS_REG_1_GCL_ENTRY_NUM_M,
QSYS_GCL_STATUS_REG_1);
interval = ocelot_read(ocelot, QSYS_GCL_STATUS_REG_2);
val = ocelot_read(ocelot, QSYS_GCL_STATUS_REG_1);
gate_state = QSYS_GCL_STATUS_REG_1_GATE_STATE_X(val);
dev_info(ocelot->dev, "GCL entry %d: states 0x%x interval %u\n",
i, gate_state, interval);
}
}
Calling it from two places: after the initial QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE
performed by vsc9959_qos_port_tas_set(), and after the one done by
vsc9959_tas_clock_adjust(), I notice the following difference.
From the tc-taprio process context, where the schedule was initially
configured, the GCL looks like this:
mscc_felix 0000:00:00.5: GCL length: 8
mscc_felix 0000:00:00.5: GCL entry 0: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 1: states 0x10 interval 200000
mscc_felix 0000:00:00.5: GCL entry 2: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 3: states 0x48 interval 200000
mscc_felix 0000:00:00.5: GCL entry 4: states 0x20 interval 300000
mscc_felix 0000:00:00.5: GCL entry 5: states 0x83 interval 200000
mscc_felix 0000:00:00.5: GCL entry 6: states 0x40 interval 300000
mscc_felix 0000:00:00.5: GCL entry 7: states 0x0 interval 200000
But from the ptp4l clock stepping process context, when the
vsc9959_tas_clock_adjust() hook is called, the GCL RAM of the
operational schedule now looks like this:
mscc_felix 0000:00:00.5: GCL length: 8
mscc_felix 0000:00:00.5: GCL entry 0: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 1: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 2: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 3: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 4: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 5: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 6: states 0x0 interval 0
mscc_felix 0000:00:00.5: GCL entry 7: states 0x0 interval 0
I do not have a formal explanation, just experimental conclusions.
It appears that after triggering QSYS_TAS_PARAM_CFG_CTRL_CONFIG_CHANGE
for a port's TAS, the GCL entry RAM is updated anyway, despite what the
documentation claims: "Specify the time interval in
QSYS::GCL_CFG_REG_2.TIME_INTERVAL. This triggers the actual RAM
write with the gate state and the time interval for the entry number
specified". We don't touch that register (through vsc9959_tas_gcl_set())
from vsc9959_tas_clock_adjust(), yet the GCL RAM is updated anyway.
It seems to be updated with effectively stale memory, which in my
testing can hold a variety of things, including even pieces of the
previously applied schedule, for particular schedule lengths.
As such, in most circumstances it is very difficult to pinpoint this
issue, because the newly updated schedule would "behave strangely",
but ultimately might still pass traffic to some extent, due to some
gate entries still being present in the stale GCL entry RAM. It is easy
to miss.
With the particular schedule given at the beginning, the GCL RAM
"happens" to be reproducibly rewritten with all zeroes, and this is
consistent with what we see: when the time-aware shaper has gate entries
with all gates closed, traffic is dropped on TX, no wonder we can't
retrieve TX timestamps.
Rewriting the GCL entry RAM when reapplying the new base time fixes the
observed issue.
Fixes: 8670dc33f48b ("net: dsa: felix: update base time of time-aware shaper when adjusting PTP time")
Reported-by: Richie Pearn <richard.pearn@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://patch.msgid.link/20250426144859.3128352-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the mtk_poll_rx() function detects the MTK_RESETTING flag, it will
jump to release_desc and refill the high word of the SDP on the 4GB RFB.
Subsequently, mtk_rx_clean will process an incorrect SDP, leading to a
panic.
Add patch from MediaTek's SDK to resolve this.
Fixes: 2d75891ebc09 ("net: ethernet: mtk_eth_soc: support 36-bit DMA addressing on MT7988")
Link: https://git01.mediatek.com/plugins/gitiles/openwrt/feeds/mtk-openwrt-feeds/+/71f47ea785699c6aa3b922d66c2bdc1a43da25b1
Signed-off-by: Chad Monroe <chad@monroe.io>
Link: https://patch.msgid.link/4adc2aaeb0fb1b9cdc56bf21cf8e7fa328daa345.1745715843.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 1a931c4f5e68 ("igc: add lock preventing multiple simultaneous PTM
transactions") added a new mutex to protect concurrent PTM transactions.
This lock is acquired in igc_ptp_reset() in order to ensure the PTM
registers are properly disabled after a device reset.
The flow where the lock is acquired already holds a spinlock, so acquiring
a mutex leads to a sleep-while-locking bug, reported both by smatch,
and the kernel test robot.
The critical section in igc_ptp_reset() does correctly use the
readx_poll_timeout_atomic variants, but the standard PTM flow uses regular
sleeping variants. This makes converting the mutex to a spinlock a bit
tricky.
Instead, re-order the locking in igc_ptp_reset. Acquire the mutex first,
and then the tmreg_lock spinlock. This is safe because there is no other
ordering dependency on these locks, as this is the only place where both
locks were acquired simultaneously. Indeed, any other flow acquiring locks
in that order would be wrong regardless.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Fixes: 1a931c4f5e68 ("igc: add lock preventing multiple simultaneous PTM transactions")
Link: https://lore.kernel.org/intel-wired-lan/Z_-P-Hc1yxcw0lTB@stanley.mountain/
Link: https://lore.kernel.org/intel-wired-lan/202504211511.f7738f5d-lkp@intel.com/T/#u
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Vitaly Lifshits <vitaly.lifshits@intel.com>
Tested-by: Mor Bar-Gabay <morx.bar.gabay@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Before the referenced commit, the shutdown just called idpf_remove(),
this way IDPF_REMOVE_IN_PROG was protecting us from the serv_task
rescheduling reset. Without this flag set the shutdown process is
vulnerable to HW reset or any other triggering conditions (such as
default mailbox being destroyed).
When one of conditions checked in idpf_service_task becomes true,
vc_event_task can be rescheduled during shutdown, this leads to accessing
freed memory e.g. idpf_req_rel_vector_indexes() trying to read
vport->q_vector_idxs. This in turn causes the system to become defunct
during e.g. systemctl kexec.
Considering using IDPF_REMOVE_IN_PROG would lead to more heavy shutdown
process, instead just cancel the serv_task before cancelling
adapter->serv_task before cancelling adapter->vc_event_task to ensure that
reset will not be scheduled while we are doing a shutdown.
Fixes: 4c9106f4906a ("idpf: fix adapter NULL pointer dereference on reboot")
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Signed-off-by: Larysa Zaremba <larysa.zaremba@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
In case of failing on rss_data->rss_key allocation the function is
freeing vport without freeing earlier allocated q_vector_idxs. Fix it.
Move from freeing in error branch to goto scheme.
Fixes: d4d558718266 ("idpf: initialize interrupts and enable vport")
Reviewed-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Suggested-by: Pavan Kumar Linga <pavan.kumar.linga@intel.com>
Signed-off-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Samuel Salin <Samuel.salin@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
|
|
Bui Quang Minh says:
====================
xsk: respect the offsets when copying frags
In commit 560d958c6c68 ("xsk: add generic XSk &xdp_buff -> skb
conversion"), we introduce a helper to convert zerocopy xdp_buff to skb.
However, in the frag copy, we mistakenly ignore the frag's offset. This
series adds the missing offset when copying frags in
xdp_copy_frags_from_zc(). This function is not used anywhere so no
backport is needed.
This series also makes xdp_copy_frags_from_zc() use page allocation API
page_pool_dev_alloc() instead of page_pool_dev_alloc_netmem() to avoid
possible confusion of the returned value.
====================
Link: https://patch.msgid.link/20250426081220.40689-1-minhquangbui99@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This commit makes xdp_copy_frags_from_zc() use page allocation API
page_pool_dev_alloc() instead of page_pool_dev_alloc_netmem() to avoid
possible confusion of the returned value.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://patch.msgid.link/20250426081220.40689-3-minhquangbui99@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In commit 560d958c6c68 ("xsk: add generic XSk &xdp_buff -> skb
conversion"), we introduce a helper to convert zerocopy xdp_buff to skb.
However, in the frag copy, we mistakenly ignore the frag's offset. This
commit adds the missing offset when copying frags in
xdp_copy_frags_from_zc(). This function is not used anywhere so no
backport is needed.
Signed-off-by: Bui Quang Minh <minhquangbui99@gmail.com>
Link: https://patch.msgid.link/20250426081220.40689-2-minhquangbui99@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use bpf_try_module_get()/bpf_module_put() instead of try_module_get()/
module_put() when handling default qdisc since users can assign a bpf
qdisc to it.
To trigger the bug:
$ bpftool struct_ops register bpf_qdisc_fq.bpf.o /sys/fs/bpf
$ echo bpf_fq > /proc/sys/net/core/default_qdisc
Fixes: c8240344956e ("bpf: net_sched: Support implementation of Qdisc_ops in bpf")
Signed-off-by: Amery Hung <ameryhung@gmail.com>
Signed-off-by: Martin KaFai Lau <martin.lau@kernel.org>
Link: https://patch.msgid.link/20250429192128.3860571-1-ameryhung@gmail.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fixes from Ulf Hansson:
"Renesas SDHI fixes:
- Fix error-paths in probe
- Fix build-error when CONFIG_REGULATOR is unset"
* tag 'mmc-v6.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
mmc: renesas_sdhi: disable clocks if registering regulator failed
mmc: renesas_sdhi: add regulator dependency
mmc: renesas_sdhi: Fix error handling in renesas_sdhi_probe
|
