| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kishon/linux-phy into usb-linus
Kishon writes:
phy: fixes for v4.1-rc
includes a fix in phy core w.r.t error checking, couple of fixes
in kconfig one which fixes randconfig error and the other
to fix dependency in QCOM PHY, driver fix in omap-usb2 in the
error path and a driver fix in rcar-gen2 to fix bit location.
|
|
Regression in commit 638139eb95d2 ("usb: hub: allow to process more usb
hub events in parallel")
The regression resulted in intermittent failure to initialise a 10-port
hub (with three internal VL812 4-port hub controllers) on boot, with a
failure rate of around 8%, due to multiple race conditions when
accessing addr_dev and slot_id in struct xhci_hcd.
This regression also exposed a problem with xhci_setup_device, which
"should be protected by the usb_address0_mutex" but no longer is due to
commit 6fecd4f2a58c ("USB: separate usb_address0 mutexes for each bus")
With separate buses (and locks) it is no longer the case that a single
lock will protect xhci_setup_device from accesses by two parallel
threads processing events on the two buses.
Fix this by adding a mutex to protect addr_dev and slot_id in struct
xhci_hcd, and by making the assignment of slot_id atomic.
Fixes multiple boot errors:
[ 0.583008] xhci_hcd 0000:00:14.0: Bad Slot ID 2
[ 0.583009] xhci_hcd 0000:00:14.0: Could not allocate xHCI USB device data structures
[ 0.583012] usb usb1-port3: couldn't allocate usb_device
And:
[ 0.637409] xhci_hcd 0000:00:14.0: Error while assigning device slot ID
[ 0.637417] xhci_hcd 0000:00:14.0: Max number of devices this xHCI host supports is 32.
[ 0.637421] usb usb1-port1: couldn't allocate usb_device
And:
[ 0.753372] xhci_hcd 0000:00:14.0: ERROR: unexpected setup context command completion code 0x0.
[ 0.753373] usb 1-3: hub failed to enable device, error -22
[ 0.753400] xhci_hcd 0000:00:14.0: Error while assigning device slot ID
[ 0.753402] xhci_hcd 0000:00:14.0: Max number of devices this xHCI host supports is 32.
[ 0.753403] usb usb1-port3: couldn't allocate usb_device
And:
[ 11.018386] usb 1-3: device descriptor read/all, error -110
And:
[ 5.753838] xhci_hcd 0000:00:14.0: Timeout while waiting for setup device command
Tested with 200 reboots, resulting in no USB hub init related errors.
Fixes: 638139eb95d2 ("usb: hub: allow to process more usb hub events in parallel")
Link: https://lkml.kernel.org/g/CAP-bSRb=A0iEYobdGCLpwynS7pkxpt_9ZnwyZTPVAoy0Y=Zo3Q@mail.gmail.com
Signed-off-by: Chris Bainbridge <chris.bainbridge@gmail.com>
Cc: <stable@vger.kernel.org> # 3.18+
[changed git commit description style for checkpatch -Mathias]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fixed regression. After commit 29e409f0f761 ("xhci: Allow xHCI drivers to
be built as separate modules") the module xhci_hcd became non-removable.
That behaviour is not expected and there're no notes about it in commit
message. The module should be removable as it blocks PM suspend/resume
functions (Debian Bug#666406).
Signed-off-by: Arthur Demchenkov <spinal.by@gmail.com>
Reviewed-by: Andrew Bresticker <abrestic@chromium.org>
Cc: <stable@vger.kernel.org> # v3.18+
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The early_idt_handlers asm code generates an array of entry
points spaced nine bytes apart. It's not really clear from that
code or from the places that reference it what's going on, and
the code only works in the first place because GAS never
generates two-byte JMP instructions when jumping to global
labels.
Clean up the code to generate the correct array stride (member size)
explicitly. This should be considerably more robust against
screw-ups, as GAS will warn if a .fill directive has a negative
count. Using '. =' to advance would have been even more robust
(it would generate an actual error if it tried to move
backwards), but it would pad with nulls, confusing anyone who
tries to disassemble the code. The new scheme should be much
clearer to future readers.
While we're at it, improve the comments and rename the array and
common code.
Binutils may start relaxing jumps to non-weak labels. If so,
this change will fix our build, and we may need to backport this
change.
Before, on x86_64:
0000000000000000 <early_idt_handlers>:
0: 6a 00 pushq $0x0
2: 6a 00 pushq $0x0
4: e9 00 00 00 00 jmpq 9 <early_idt_handlers+0x9>
5: R_X86_64_PC32 early_idt_handler-0x4
...
48: 66 90 xchg %ax,%ax
4a: 6a 08 pushq $0x8
4c: e9 00 00 00 00 jmpq 51 <early_idt_handlers+0x51>
4d: R_X86_64_PC32 early_idt_handler-0x4
...
117: 6a 00 pushq $0x0
119: 6a 1f pushq $0x1f
11b: e9 00 00 00 00 jmpq 120 <early_idt_handler>
11c: R_X86_64_PC32 early_idt_handler-0x4
After:
0000000000000000 <early_idt_handler_array>:
0: 6a 00 pushq $0x0
2: 6a 00 pushq $0x0
4: e9 14 01 00 00 jmpq 11d <early_idt_handler_common>
...
48: 6a 08 pushq $0x8
4a: e9 d1 00 00 00 jmpq 120 <early_idt_handler_common>
4f: cc int3
50: cc int3
...
117: 6a 00 pushq $0x0
119: 6a 1f pushq $0x1f
11b: eb 03 jmp 120 <early_idt_handler_common>
11d: cc int3
11e: cc int3
11f: cc int3
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Acked-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Binutils <binutils@sourceware.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: H.J. Lu <hjl.tools@gmail.com>
Cc: Jan Beulich <JBeulich@suse.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/ac027962af343b0c599cbfcf50b945ad2ef3d7a8.1432336324.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
This reverts commit 7290006d8c0900c56d8c58428134f02c35109d17.
Through the regression report, it was revealed that the
tpacpi_led_set() call to thinkpad_acpi helper doesn't only toggle the
mute LED but actually mutes the sound. This is contradiction to the
expectation, and rather confuses user.
According to Henrique, it's not trivial to judge which TP model
behaves "LED-only" and which model does whatever more intrusive, as
Lenovo's implementations vary model by model. So, from the safety
reason, we should revert the patch for now.
Reported-by: Martin Steigerwald <martin@lichtvoll.de>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Microsoft LifeCam HD-3000 (045e:0779) needs a similar quirk for
suppressing the unsupported sample rate inquiry.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98481
Cc: <stable@vger.kernel.org>
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fix from Thomas Gleixner:
"One more fix from the timer departement:
- Handle division of negative nanosecond values proper on 32bit.
A recent cleanup wrecked the sign handling of the dividend and
dropped the check for negative divisors"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
ktime: Fix ktime_divns to do signed division
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irqchip fix from Thomas Gleixner:
"A fix for a GIC-V3 irqchip regression which prevents some systems from
booting"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gicv3-its: ITS table size should not be smaller than PSZ
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client
Pull two Ceph fixes from Sage Weil:
"These fix an issue with the RBD notifications when there are topology
changes in the cluster"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
Revert "libceph: clear r_req_lru_item in __unregister_linger_request()"
libceph: request a new osdmap if lingering request maps to no osd
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs
Pull btrfs fixes from Chris Mason:
"I fixed up a regression from 4.0 where conversion between different
raid levels would sometimes bail out without converting.
Filipe tracked down a race where it was possible to double allocate
chunks on the drive.
Mark has a fix for fiemap. All three will get bundled off for stable
as well"
* 'for-linus-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
Btrfs: fix regression in raid level conversion
Btrfs: fix racy system chunk allocation when setting block group ro
btrfs: clear 'ret' in btrfs_check_shared() loop
|
|
Remove extra space between platform prefix and DRIVER_NAME in MODULE_ALIAS.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
|
|
This patch sets display clock correctly. If Display clock isn't set
correctly then you would find below messages and Display controller
doesn't work correctly.
exynos-drm: No connectors reported connected with modes
[drm] Cannot find any crtc or sizes - going 1024x768
Fixes: abc0b1447d49 ("drm: Perform basic sanity checks on probed modes")
Cc: <stable@vger.kernel.org>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Tested-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
|
|
Pull drm fixes from Dave Airlie:
"Radeon has two displayport fixes, one for a regression.
i915 regression flicker fix needed so 4.0 can get fixed.
A bunch of msm fixes and a bunch of exynos fixes, these two are
probably a bit larger than I'd like, but most of them seems pretty
good"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (29 commits)
drm/radeon: fix error flag checking in native aux path
drm/radeon: retry dcpd fetch
drm/msm/mdp5: fix incorrect parameter for msm_framebuffer_iova()
drm/exynos: dp: Lower level of EDID read success message
drm/exynos: cleanup exynos_drm_plane
drm/exynos: 'win' is always unsigned
drm/exynos: mixer: don't dump registers under spinlock
drm/exynos: Consolidate return statements in fimd_bind()
drm/exynos: Constify exynos_drm_crtc_ops
drm/exynos: Fix build breakage on !DRM_EXYNOS_FIMD
drm/exynos: mixer: Constify platform_device_id
drm/exynos: mixer: cleanup pixelformat handling
drm/exynos: mixer: also allow NV21 for the video processor
drm/exynos: mixer: remove buffer count handling in vp_video_buffer()
drm/exynos: plane: honor buffer offset for dma_addr
drm/exynos: fb: use drm_format_num_planes to get buffer count
drm/i915: fix screen flickering
drm/msm: fix locking inconsistencies in gpu->destroy()
drm/msm/dsi: Simplify the code to get the number of read byte
drm/msm: Attach assigned encoder to eDP and DSI connectors
...
|
|
Pull networking fixes from David Miller:
1) Don't leak ipvs->sysctl_tbl, from Tommi Rentala.
2) Fix neighbour table entry leak in rocker driver, from Ying Xue.
3) Do not emit bonding notifications for unregistered interfaces, from
Nicolas Dichtel.
4) Set ipv6 flow label properly when in TIME_WAIT state, from Florent
Fourcot.
5) Fix regression in ipv6 multicast filter test, from Henning Rogge.
6) do_replace() in various footables netfilter modules is missing a
check for 0 counters in the datastructure provided by the user. Fix
from Dave Jones, and found with trinity.
7) Fix RCU bug in packet scheduler classifier module unloads, from
Daniel Borkmann.
8) Avoid deadlock in tcp_get_info() by using u64_sync. From Eric
Dumzaet.
9) Input packet processing can race with inetdev_destroy() teardown,
fix potential OOPS in ip_error() by explicitly testing whether the
inetdev is still attached. From Eric W Biederman.
10) MLDv2 parser in bridge multicast code breaks too early while
parsing. Fix from Thadeu Lima de Souza Cascardo.
11) Asking for settings on non-zero PHYID doesn't work because we do not
import the command structure from the user and use the PHYID
provided there. Fix from Arun Parameswaran.
12) Fix UDP checksums with IPV6 RAW sockets, from Vlad Yasevich.
13) Missing NF_TABLES depends for TPROXY etc can cause build failures,
fix from Florian Westphal.
14) Fix netfilter conntrack to handle RFC5961 challenge ACKs properly,
from Jesper Dangaard Brouer.
15) If netlink autobind retry fails, we have to reset the sockets portid
back to zero. From Herbert Xu.
16) VXLAN netns exit code unregisters using wrong device, from John W
Linville.
17) Add some USB device IDs to ath3k and btusb bluetooth drivers, from
Dmitry Tunin and Wen-chien Jesse Sung.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (44 commits)
bridge: fix lockdep splat
net: core: 'ethtool' issue with querying phy settings
bridge: fix parsing of MLDv2 reports
ARM: zynq: DT: Use the zynq binding with macb
net: macb: Disable half duplex gigabit on Zynq
net: macb: Document zynq gem dt binding
ipv4: fill in table id when replacing a route
cdc_ncm: Fix tx_bytes statistics
ipv4: Avoid crashing in ip_error
tcp: fix a potential deadlock in tcp_get_info()
net: sched: fix call_rcu() race on classifier module unloads
net: phy: Make sure phy_start() always re-enables the phy interrupts
ipv6: fix ECMP route replacement
ipv6: do not delete previously existing ECMP routes if add fails
Revert "netfilter: bridge: query conntrack about skb dnat"
netfilter: ensure number of counters is >0 in do_replace()
netfilter: nfnetlink_{log,queue}: Register pernet in first place
tcp: don't over-send F-RTO probes
tcp: only undo on partial ACKs in CA_Loss
net/ipv6/udp: Fix ipv6 multicast socket filter regression
...
|
|
Pull block fixes from Jens Axboe:
"Three small fixes that have been picked up the last few weeks.
Specifically:
- Fix a memory corruption issue in NVMe with malignant user
constructed request. From Christoph.
- Kill (now) unused blk_queue_bio(), dm was changed to not need this
anymore. From Mike Snitzer.
- Always use blk_schedule_flush_plug() from the io_schedule() path
when flushing a plug, fixing a !TASK_RUNNING warning with md. From
Shaohua"
* 'for-linus' of git://git.kernel.dk/linux-block:
sched: always use blk_schedule_flush_plug in io_schedule_out
nvme: fix kernel memory corruption with short INQUIRY buffers
block: remove export for blk_queue_bio
|
|
Pull md bugfixes from Neil Brown:
"I have a few more raid5 bugfixes pending, but I want them to get a bit
more review first. In the meantime:
- one serious RAID0 data corruption - caused by recent bugfix that
wasn't reviewed properly.
- one raid5 fix in new code (a couple more of those to come).
- one little fix to stop static analysis complaining about silly rcu
annotation"
* tag 'md/4.1-rc4-fixes' of git://neil.brown.name/md:
md/bitmap: remove rcu annotation from pointer arithmetic.
md/raid0: fix restore to sector variable in raid0_make_request
raid5: fix broken async operation chain
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Updates for the input subsystem.
The main change is that we tell joydev not to touch "absolute mice",
such as VMware virtual mouse, as that produced bad result (cursor
stuck in upper right corner) with games"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: smtpe-ts - wait 50mS until polling for pen-up
Input: smtpe-ts - use msecs_to_jiffies() instead of HZ
Input: joydev - don't classify the vmmouse as a joystick
Input: vmmouse - do not reference non-existing version of X driver
Input: alps - fix finger jumps on lifting 2 fingers on v7 touchpad
Input: elantech - fix semi-mt protocol for v3 HW
Input: sx8654 - fix memory allocation check
|
|
Pull another crypto fix from Herbert Xu:
"Fix ICV corruption in s390/ghash when the same tfm is used by more
than one thread"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: s390/ghash - Fix incorrect ghash icv buffer handling.
|
|
Following lockdep splat was reported :
[ 29.382286] ===============================
[ 29.382315] [ INFO: suspicious RCU usage. ]
[ 29.382344] 4.1.0-0.rc0.git11.1.fc23.x86_64 #1 Not tainted
[ 29.382380] -------------------------------
[ 29.382409] net/bridge/br_private.h:626 suspicious
rcu_dereference_check() usage!
[ 29.382455]
other info that might help us debug this:
[ 29.382507]
rcu_scheduler_active = 1, debug_locks = 0
[ 29.382549] 2 locks held by swapper/0/0:
[ 29.382576] #0: (((&p->forward_delay_timer))){+.-...}, at:
[<ffffffff81139f75>] call_timer_fn+0x5/0x4f0
[ 29.382660] #1: (&(&br->lock)->rlock){+.-...}, at:
[<ffffffffa0450dc1>] br_forward_delay_timer_expired+0x31/0x140
[bridge]
[ 29.382754]
stack backtrace:
[ 29.382787] CPU: 0 PID: 0 Comm: swapper/0 Not tainted
4.1.0-0.rc0.git11.1.fc23.x86_64 #1
[ 29.382838] Hardware name: LENOVO 422916G/LENOVO, BIOS A1KT53AUS 04/07/2015
[ 29.382882] 0000000000000000 3ebfc20364115825 ffff880666603c48
ffffffff81892d4b
[ 29.382943] 0000000000000000 ffffffff81e124e0 ffff880666603c78
ffffffff8110bcd7
[ 29.383004] ffff8800785c9d00 ffff88065485ac58 ffff880c62002800
ffff880c5fc88ac0
[ 29.383065] Call Trace:
[ 29.383084] <IRQ> [<ffffffff81892d4b>] dump_stack+0x4c/0x65
[ 29.383130] [<ffffffff8110bcd7>] lockdep_rcu_suspicious+0xe7/0x120
[ 29.383178] [<ffffffffa04520f9>] br_fill_ifinfo+0x4a9/0x6a0 [bridge]
[ 29.383225] [<ffffffffa045266b>] br_ifinfo_notify+0x11b/0x4b0 [bridge]
[ 29.383271] [<ffffffffa0450d90>] ? br_hold_timer_expired+0x70/0x70 [bridge]
[ 29.383320] [<ffffffffa0450de8>]
br_forward_delay_timer_expired+0x58/0x140 [bridge]
[ 29.383371] [<ffffffffa0450d90>] ? br_hold_timer_expired+0x70/0x70 [bridge]
[ 29.383416] [<ffffffff8113a033>] call_timer_fn+0xc3/0x4f0
[ 29.383454] [<ffffffff81139f75>] ? call_timer_fn+0x5/0x4f0
[ 29.383493] [<ffffffff8110a90f>] ? lock_release_holdtime.part.29+0xf/0x200
[ 29.383541] [<ffffffffa0450d90>] ? br_hold_timer_expired+0x70/0x70 [bridge]
[ 29.383587] [<ffffffff8113a6a4>] run_timer_softirq+0x244/0x490
[ 29.383629] [<ffffffff810b68cc>] __do_softirq+0xec/0x670
[ 29.383666] [<ffffffff810b70d5>] irq_exit+0x145/0x150
[ 29.383703] [<ffffffff8189f506>] smp_apic_timer_interrupt+0x46/0x60
[ 29.383744] [<ffffffff8189d523>] apic_timer_interrupt+0x73/0x80
[ 29.383782] <EOI> [<ffffffff816f131f>] ? cpuidle_enter_state+0x5f/0x2f0
[ 29.383832] [<ffffffff816f131b>] ? cpuidle_enter_state+0x5b/0x2f0
Problem here is that br_forward_delay_timer_expired() is a timer
handler, calling br_ifinfo_notify() which assumes either rcu_read_lock()
or RTNL are held.
Simplest fix seems to add rcu read lock section.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Reported-by: Dominick Grift <dac.override@gmail.com>
Cc: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When trying to configure the settings for PHY1, using commands
like 'ethtool -s eth0 phyad 1 speed 100', the 'ethtool' seems to
modify other settings apart from the speed of the PHY1, in the
above case.
The ethtool seems to query the settings for PHY0, and use this
as the base to apply the new settings to the PHY1. This is
causing the other settings of the PHY 1 to be wrongly
configured.
The issue is caused by the '_ethtool_get_settings()' API, which
gets called because of the 'ETHTOOL_GSET' command, is clearing
the 'cmd' pointer (of type 'struct ethtool_cmd') by calling
memset. This clears all the parameters (if any) passed for the
'ETHTOOL_GSET' cmd. So the driver's callback is always invoked
with 'cmd->phy_address' as '0'.
The '_ethtool_get_settings()' is called from other files in the
'net/core'. So the fix is applied to the 'ethtool_get_settings()'
which is only called in the context of the 'ethtool'.
Signed-off-by: Arun Parameswaran <aparames@broadcom.com>
Reviewed-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When more than a multicast address is present in a MLDv2 report, all but
the first address is ignored, because the code breaks out of the loop if
there has not been an error adding that address.
This has caused failures when two guests connected through the bridge
tried to communicate using IPv6. Neighbor discoveries would not be
transmitted to the other guest when both used a link-local address and a
static address.
This only happens when there is a MLDv2 querier in the network.
The fix will only break out of the loop when there is a failure adding a
multicast address.
The mdb before the patch:
dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp
dev ovirtmgmt port bond0.86 grp ff02::2 temp
After the patch:
dev ovirtmgmt port vnet0 grp ff02::1:ff7d:6603 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff7d:6604 temp
dev ovirtmgmt port bond0.86 grp ff02::fb temp
dev ovirtmgmt port bond0.86 grp ff02::2 temp
dev ovirtmgmt port bond0.86 grp ff02::d temp
dev ovirtmgmt port vnet0 grp ff02::1:ff00:76 temp
dev ovirtmgmt port bond0.86 grp ff02::16 temp
dev ovirtmgmt port vnet1 grp ff02::1:ff00:77 temp
dev ovirtmgmt port bond0.86 grp ff02::1:ff00:def temp
dev ovirtmgmt port bond0.86 grp ff02::1:ffa1:40bf temp
Fixes: 08b202b67264 ("bridge br_multicast: IPv6 MLD support.")
Reported-by: Rik Theys <Rik.Theys@esat.kuleuven.be>
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@redhat.com>
Tested-by: Rik Theys <Rik.Theys@esat.kuleuven.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the new zynq binding for macb ethernet, since it will disable half
duplex gigabit like the Zynq TRM says to do.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to the Zynq TRM, gigabit half duplex is not supported. Add a
new cap and compatible string so Zynq can avoid advertising that mode.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When replacing an IPv4 route, tb_id member of the new fib_alias
structure is not set in the replace code path so that the new route is
ignored.
Fixes: 0ddcf43d5d4a ("ipv4: FIB Local/MAIN table collapse")
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Acked-by: Alexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tx_curr_frame_payload field is u32. When we try to calculate a
small negative delta based on it, we end up with a positive integer
close to 2^32 instead. So the tx_bytes pointer increases by about
2^32 for every transmitted frame.
Fix by calculating the delta as a signed long.
Cc: Ben Hutchings <ben.hutchings@codethink.co.uk>
Reported-by: Florian Bruhin <me@the-compiler.org>
Fixes: 7a1e890e2168 ("usbnet: Fix tx_bytes statistic running backward in cdc_ncm")
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contain Netfilter fixes for your net tree, they are:
1) Fix a race in nfnetlink_log and nfnetlink_queue that can lead to a crash.
This problem is due to wrong order in the per-net registration and netlink
socket events. Patch from Francesco Ruggeri.
2) Make sure that counters that userspace pass us are higher than 0 in all the
x_tables frontends. Discovered via Trinity, patch from Dave Jones.
3) Revert a patch for br_netfilter to rely on the conntrack status bits. This
breaks stateless IPv6 NAT transformations. Patch from Florian Westphal.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ip_error does not check if in_dev is NULL before dereferencing it.
IThe following sequence of calls is possible:
CPU A CPU B
ip_rcv_finish
ip_route_input_noref()
ip_route_input_slow()
inetdev_destroy()
dst_input()
With the result that a network device can be destroyed while processing
an input packet.
A crash was triggered with only unicast packets in flight, and
forwarding enabled on the only network device. The error condition
was created by the removal of the network device.
As such it is likely the that error code was -EHOSTUNREACH, and the
action taken by ip_error (if in_dev had been accessible) would have
been to not increment any counters and to have tried and likely failed
to send an icmp error as the network device is going away.
Therefore handle this weird case by just dropping the packet if
!in_dev. It will result in dropping the packet sooner, and will not
result in an actual change of behavior.
Fixes: 251da4130115b ("ipv4: Cache ip_error() routes even when not forwarding.")
Reported-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Tested-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: Vittorio Gambaletta <linuxbugs@vittgam.net>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Taking socket spinlock in tcp_get_info() can deadlock, as
inet_diag_dump_icsk() holds the &hashinfo->ehash_locks[i],
while packet processing can use the reverse locking order.
We could avoid this locking for TCP_LISTEN states, but lockdep would
certainly get confused as all TCP sockets share same lockdep classes.
[ 523.722504] ======================================================
[ 523.728706] [ INFO: possible circular locking dependency detected ]
[ 523.734990] 4.1.0-dbg-DEV #1676 Not tainted
[ 523.739202] -------------------------------------------------------
[ 523.745474] ss/18032 is trying to acquire lock:
[ 523.750002] (slock-AF_INET){+.-...}, at: [<ffffffff81669d44>] tcp_get_info+0x2c4/0x360
[ 523.758129]
[ 523.758129] but task is already holding lock:
[ 523.763968] (&(&hashinfo->ehash_locks[i])->rlock){+.-...}, at: [<ffffffff816bcb75>] inet_diag_dump_icsk+0x1d5/0x6c0
[ 523.774661]
[ 523.774661] which lock already depends on the new lock.
[ 523.774661]
[ 523.782850]
[ 523.782850] the existing dependency chain (in reverse order) is:
[ 523.790326]
-> #1 (&(&hashinfo->ehash_locks[i])->rlock){+.-...}:
[ 523.796599] [<ffffffff811126bb>] lock_acquire+0xbb/0x270
[ 523.802565] [<ffffffff816f5868>] _raw_spin_lock+0x38/0x50
[ 523.808628] [<ffffffff81665af8>] __inet_hash_nolisten+0x78/0x110
[ 523.815273] [<ffffffff816819db>] tcp_v4_syn_recv_sock+0x24b/0x350
[ 523.822067] [<ffffffff81684d41>] tcp_check_req+0x3c1/0x500
[ 523.828199] [<ffffffff81682d09>] tcp_v4_do_rcv+0x239/0x3d0
[ 523.834331] [<ffffffff816842fe>] tcp_v4_rcv+0xa8e/0xc10
[ 523.840202] [<ffffffff81658fa3>] ip_local_deliver_finish+0x133/0x3e0
[ 523.847214] [<ffffffff81659a9a>] ip_local_deliver+0xaa/0xc0
[ 523.853440] [<ffffffff816593b8>] ip_rcv_finish+0x168/0x5c0
[ 523.859624] [<ffffffff81659db7>] ip_rcv+0x307/0x420
Lets use u64_sync infrastructure instead. As a bonus, 64bit
arches get optimized, as these are nop for them.
Fixes: 0df48c26d841 ("tcp: add tcpi_bytes_acked to tcp_info")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we have a read_boot_clock64() function available on every
architecture, and converted all the users to it, it's time to remove
the (now unused) read_boot_clock() completely from the kernel.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
[jstultz: Minor commit message tweak suggested by Ingo]
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
As part of addressing the "y2038 problem" for in-kernel uses,
this patch converts read_boot_clock() to read_boot_clock64()
and read_persistent_clock() to read_persistent_clock64() using
timespec64.
Rename some instances of 'timespec' to 'timespec64' in time.c and
related references
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
[jstultz: Fixed minor style and grammer tweaks
pointed out by Ingo]
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
On 32-bit systems, timespec64_add_ns() calls __iter_div_u64_rem()
which needs math64.h, and we want to include time64.h in some
cases.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Xunlei Pang <pang.xunlei@linaro.org>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
The timer_start event now shows whether the timer is
deferrable in case of a low-res timer. The debug_activate
function now includes a deferrable flag while calling
the trace_timer_start event.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Badhri Jagan Sridharan <Badhri@google.com>
[jstultz: Fixed minor whitespace and grammer tweaks
pointed out by Ingo]
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
Ingo suggested that the timekeeping debugging variables
recently added should not be global, and should be tied
to the timekeeper's read_base.
Thus this patch implements that suggestion.
This version is different from the earlier versions
as it keeps the variables in the timekeeper structure
rather then in the tkr.
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Prarit Bhargava <prarit@redhat.com>
Cc: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
This patch series introduces a new function
u32 ktime_get_resolution_ns(void)
which allows to clean up some driver code.
In particular the IIO subsystem has a function to provide timestamps for
events but no means to get their resolution. So currently the dht11 driver
tries to guess the resolution in a rather messy and convoluted way. We
can do much better with the new code.
This API is not designed to be exposed to user space.
This has been tested on i386, sunxi and mxs.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Harald Geyer <harald@ccbib.org>
[jstultz: Tweaked to make it build after upstream changes]
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
Invalid values may overflow later, leading to undefined behaviour when
multiplied by 60 to get the amount of seconds.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Signed-off-by: John Stultz <john.stultz@linaro.org>
|
|
"base_irq" needs to be signed for the error handling to work. Also we
can remove the initialization because we re-assign it later.
Fixes: aa8d6b73ea33 ('ARM: pxa: pxa_cplds: add lubbock and mainstone IO')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The pl330 device could hang infinitely on certain boards when DMA
channels are terminated.
It was caused by lack of runtime resume when executing
pl330_terminate_all() which calls the _stop() function. _stop() accesses
device register and can loop infinitely while checking for device state.
The hang was confirmed by Dinh Nguyen on Altera SOCFPGA Cyclone V
board during boot. It can be also triggered with:
$ echo 1 > /sys/module/dmatest/parameters/iterations
$ echo dma1chan0 > /sys/module/dmatest/parameters/channel
$ echo 1 > /sys/module/dmatest/parameters/run
$ sleep 1
$ cat /sys/module/dmatest/parameters/run
Reported-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Fixes: ae43b3289186 ("ARM: 8202/1: dmaengine: pl330: Add runtime Power Management support v12")
Cc: <stable@vger.kernel.org>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
If no_irq_chip is used for wake up (e.g. gpio-keys with a simple GPIO
controller), the following warning is printed on resume from s2ram:
WANING: CPU: 0 PID: 1046 at kernel/irq/manage.c:537 irq_set_irq_wake+0x9c/0xf8()
Unbalanced IRQ 113 wake disable
This happens because no_irq_chip does not implement
irq_chip.irq_set_wake(), causing set_irq_wake_real() to return -ENXIO,
and irq_set_irq_wake() to reset the wake_depth to zero.
Set IRQCHIP_SKIP_SET_WAKE to indicate that irq_chip.irq_set_wake() is
not implemented.
Cfr. commit 10a50f1ab5f06c9a ("genirq: Set IRQCHIP_SKIP_SET_WAKE flag
for dummy_irq_chip").
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Gregory Clement <gregory.clement@free-electrons.com>
Link: http://lkml.kernel.org/r/1432281529-23325-1-git-send-email-geert%2Brenesas@glider.be
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
PTR_ERR(NULL) returns 0 so current code returns 0 if ioremap fails, fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Yingjoe Chen <yingjoe.chen@mediatek.com>
Cc: linux-mediatek@lists.infradead.org <linux-mediatek@lists.infradead.org>
Cc: Jason Cooper <jason@lakedaemon.net>
Link: http://lkml.kernel.org/r/1432220254.29544.1.camel@ingics.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
For some CPU models I broke the AVX2 feature detection in:
7bc371faa9cd ("x86/fpu, crypto x86/camellia_aesni_avx2: Simplify the camellia_aesni_init() xfeature checks")
534ff06e3929 ("x86/fpu, crypto x86/serpent_avx2: Simplify the init() xfeature checks")
... because I did not realize that it's possible for a CPU to support
the xstate necessary for AVX2 execution (XSTATE_YMM), but not have
the AVX2 instructions themselves.
Restore the necessary CPUID checks as well.
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Fenghua Yu <fenghua.yu@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
* fix firmware name and other things to enable 3165
* fix bad APMG configuration for 8000 (no AMPG on these devices)
* fix MAC address assignment for 8000
* fix firmware debugging triggers (MLME)
* fix several bugs in low power states code (net-detect,
d0i3)
|
|
In
commit f02ad907cd9e7fe3a6405d2d005840912f1ed258
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Thu Jan 22 16:36:23 2015 +0100
drm/atomic-helpers: Recover full cursor plane behaviour
we've added a hack to atomic helpers to never to vblank waits for
cursor updates through the legacy apis since that's what X expects.
Unfortunately we've (again) forgotten to adjust the transitional
helpers. Do this now.
This fixes regressions for drivers only partially converted over to
atomic (like i915).
Reported-by: Pekka Paalanen <ppaalanen@gmail.com>
Cc: Pekka Paalanen <ppaalanen@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Reviewed-and-tested-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
into drm-fixes
Just two small DP fixes for 4.1
* 'drm-fixes-4.1' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: fix error flag checking in native aux path
drm/radeon: retry dcpd fetch
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
There's a stable backport from Ander [1] that combines this and a few
other commits to fix the flickering on v4.0, reported in [2] among
others. Having this upstream is obviously a requirement for stable.
* tag 'drm-intel-fixes-2015-05-21' of git://anongit.freedesktop.org/drm-intel:
drm/i915: fix screen flickering
|
|
Multitheaded tests showed that the icv buffer in the current ghash
implementation is not handled correctly. A move of this working ghash
buffer value to the descriptor context fixed this. Code is tested and
verified with an multithreaded application via af_alg interface.
Cc: stable@vger.kernel.org
Signed-off-by: Harald Freudenberger <freude@linux.vnet.ibm.com>
Signed-off-by: Gerald Schaefer <geraldsc@linux.vnet.ibm.com>
Reported-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull two xen bugfixes from David Vrabel:
- fix ARM build regression.
- fix VIRQ_CONSOLE related oops.
* tag 'for-linus-4.1b-rc4-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/events: don't bind non-percpu VIRQs with percpu chip
xen/arm: Define xen_arch_suspend()
|
|
Pull KVM fixes from Paolo Bonzini:
"This includes a fix for two oopses, one on PPC and on x86.
The rest is fixes for bugs with newer Intel processors"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
kvm/fpu: Enable eager restore kvm FPU for MPX
Revert "KVM: x86: drop fpu_activate hook"
kvm: fix crash in kvm_vcpu_reload_apic_access_page
KVM: MMU: fix SMAP virtualization
KVM: MMU: fix CR4.SMEP=1, CR0.WP=0 with shadow pages
KVM: MMU: fix smap permission check
KVM: PPC: Book3S HV: Fix list traversal in error case
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"Bug fixes.
Three for our crypto code, two for eBPF, and one memory management fix
to get machines with memory > 8TB working"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/mm: correct return value of pmd_pfn
s390/crypto: fix stckf loop
s390/zcrypt: Fix invalid domain handling during ap module unload
s390/bpf: Fix gcov stack space problem
s390/zcrypt: fixed ap poll timer behavior
s390/bpf: Adjust ALU64_DIV/MOD to match interpreter change
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This batch became slightly large, just because I've been on vacation
for the last two weeks. Nothing to scare much here, all
device-specific fixes, mostly small patches.
Majority of patches are for HD-audio, especially Dell machines. The
rest are small ASoC fixes for various codecs, and a USB-audio quirk.
One PCM fix is included to ease the faulty condition checks in the
case of two periods PCM buffers"
* tag 'sound-4.1-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Disable widget power-saving for ALC292 & co
ALSA: hda - Reduce verbs by node power-saves
ALSA: sound/atmel/ac97c.c: remove unused variable
ALSA: usb-audio: Add quirk for MS LifeCam Studio
ALSA: pcm: Modify double acknowledged interrupts check condition
ALSA: hda/realtek - ALC292 dock fix for Thinkpad L450
ALSA: hda - Add Conexant codecs CX20721, CX20722, CX20723 and CX20724
ALSA: hda - Fix headset mic and mic-in for a Dell desktop
ASoC: wm8994: correct BCLK DIV 348 to 384
ASoC: wm8960: fix "RINPUT3" audio route error
ASoC: dapm: Modify widget stream name according to prefix
ALSA: hda - Add headset mic quirk for Dell Inspiron 5548
ASoC: rt5645: Fix mask for setting RT5645_DMIC_2_DP_GPIO12 bit
ASoC: rt5645: Add ACPI match ID
ALSA: hda/realtek - Add ALC298 alias name for Dell
ASoC: uda1380: Avoid accessing i2c bus when codec is disabled
ALSA: hda/realtek - Fix typo for ALC286/ALC288
ASoC: mc13783: Fix wrong mask value used in mc13xxx_reg_rmw() calls
ALSA: hda - Add headphone quirk for Lifebook E752
ASoC: davinci-mcasp: Correct pm status check in suspend callback
|
