| Age | Commit message (Collapse) | Author |
|---|
|
We need program ring buffer on instance 1 register space domain,
when only if instance 1 available, with two instances or instance 0,
and we need only program instance 0 regsiter space domain for ring.
Signed-off-by: Leo Liu <leo.liu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
MTU probing initialization occurred only at connect() and at SYN or
SYN-ACK reception, but the former sets MSS to either the default or the
user set value (through TCP_MAXSEG sockopt) and the latter never happens
with repaired sockets.
The result was that, with MTU probing enabled and unless TCP_MAXSEG
sockopt was used before connect(), probing would be stuck at
tcp_base_mss value until tcp_probe_interval seconds have passed.
Signed-off-by: Douglas Caetano dos Santos <douglascs@taghos.com.br>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If you attempt a TCP mount from an host that is unreachable in a way
that triggers an immediate error from kernel_connect(), that error
does not propagate up, instead EAGAIN is reported.
This results in call_connect_status receiving the wrong error.
A case that it easy to demonstrate is to attempt to mount from an
address that results in ENETUNREACH, but first deleting any default
route.
Without this patch, the mount.nfs process is persistently runnable
and is hard to kill. With this patch it exits as it should.
The problem is caused by the fact that xs_tcp_force_close() eventually
calls
xprt_wake_pending_tasks(xprt, -EAGAIN);
which causes an error return of -EAGAIN. so when xs_tcp_setup_sock()
calls
xprt_wake_pending_tasks(xprt, status);
the status is ignored.
Fixes: 4efdd92c9211 ("SUNRPC: Remove TCP client connection reset hack")
Signed-off-by: NeilBrown <neilb@suse.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
Commit b685d3d65ac7 "block: treat REQ_FUA and REQ_PREFLUSH as
synchronous" removed REQ_SYNC flag from WRITE_{FUA|PREFLUSH|...}
definitions. generic_make_request_checks() however strips REQ_FUA and
REQ_PREFLUSH flags from a bio when the storage doesn't report volatile
write cache and thus write effectively becomes asynchronous which can
lead to performance regressions
Fix the problem by making sure all bios which are synchronous are
properly marked with REQ_SYNC.
CC: linux-raid@vger.kernel.org
CC: Shaohua Li <shli@kernel.org>
Fixes: b685d3d65ac791406e0dfd8779cc9b3707fea5a3
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Shaohua Li <shli@fb.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs
Pull overlayfs fixes from Miklos Szeredi:
"Fix regressions:
- missing CONFIG_EXPORTFS dependency
- failure if upper fs doesn't support xattr
- bad error cleanup
This also adds the concept of "impure" directories complementing the
"origin" marking introduced in -rc1. Together they enable getting
consistent st_ino and d_ino for directory listings.
And there's a bug fix and a cleanup as well"
* 'overlayfs-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/vfs:
ovl: filter trusted xattr for non-admin
ovl: mark upper merge dir with type origin entries "impure"
ovl: mark upper dir with type origin entries "impure"
ovl: remove unused arg from ovl_lookup_temp()
ovl: handle rename when upper doesn't support xattr
ovl: don't fail copy-up if upper doesn't support xattr
ovl: check on mount time if upper fs supports setting xattr
ovl: fix creds leak in copy up error path
ovl: select EXPORTFS
|
|
When adding a cfq_group into the cfq service tree, we use CFQ_IDLE_DELAY
as the delay of cfq_group's vdisktime if there have been other cfq_groups
already.
When cfq is under iops mode, commit 9a7f38c42c2b ("cfq-iosched: Convert
from jiffies to nanoseconds") could result in a large iops delay and
lead to an abnormal io schedule delay for the added cfq_group. To fix
it, we just need to revert to the old CFQ_IDLE_DELAY value: HZ / 5
when iops mode is enabled.
Despite having the same value, the delay of a cfq_queue in idle class
and the delay of cfq_group are different things, so I define two new
macros for the delay of a cfq_group under time-slice mode and iops mode.
Fixes: 9a7f38c42c2b ("cfq-iosched: Convert from jiffies to nanoseconds")
Cc: <stable@vger.kernel.org> # 4.8+
Signed-off-by: Hou Tao <houtao1@huawei.com>
Acked-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
We've had user reports of unmount hangs in xfs_wait_buftarg() that
analysis shows is due to btp->bt_io_count == -1. bt_io_count
represents the count of in-flight asynchronous buffers and thus
should always be >= 0. xfs_wait_buftarg() waits for this value to
stabilize to zero in order to ensure that all untracked (with
respect to the lru) buffers have completed I/O processing before
unmount proceeds to tear down in-core data structures.
The value of -1 implies an I/O accounting decrement race. Indeed,
the fact that xfs_buf_ioacct_dec() is called from xfs_buf_rele()
(where the buffer lock is no longer held) means that bp->b_flags can
be updated from an unsafe context. While a user-level reproducer is
currently not available, some intrusive hacks to run racing buffer
lookups/ioacct/releases from multiple threads was used to
successfully manufacture this problem.
Existing callers do not expect to acquire the buffer lock from
xfs_buf_rele(). Therefore, we can not safely update ->b_flags from
this context. It turns out that we already have separate buffer
state bits and associated serialization for dealing with buffer LRU
state in the form of ->b_state and ->b_lock. Therefore, replace the
_XBF_IN_FLIGHT flag with a ->b_state variant, update the I/O
accounting wrappers appropriately and make sure they are used with
the correct locking. This ensures that buffer in-flight state can be
modified at buffer release time without racing with modifications
from a buffer lock holder.
Fixes: 9c7504aa72b6 ("xfs: track and serialize in-flight async buffers against unmount")
Cc: <stable@vger.kernel.org> # v4.8+
Signed-off-by: Brian Foster <bfoster@redhat.com>
Reviewed-by: Nikolay Borisov <nborisov@suse.com>
Tested-by: Libor Pechacek <lpechacek@suse.com>
Reviewed-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
|
|
Commit b685d3d65ac7 ("block: treat REQ_FUA and REQ_PREFLUSH as
synchronous") removed REQ_SYNC flag from WRITE_{FUA|PREFLUSH|...}
definitions. generic_make_request_checks() however strips REQ_FUA and
REQ_PREFLUSH flags from a bio when the storage doesn't report volatile
write cache and thus write effectively becomes asynchronous which can
lead to performance regressions.
Fix the problem by making sure all bios which are synchronous are
properly marked with REQ_SYNC.
Fixes: b685d3d65ac7 ("block: treat REQ_FUA and REQ_PREFLUSH as synchronous")
Cc: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
In the conversion to drop drm_modeset_lock_all and the magic implicit
context I failed to realize that _resume starts out with a pile of
state copies, but not with the locks. And hence drm_atomic_commit
won't grab these for us.
v2: Add locking checks in helpers to make sure we catch this in the
future. Note we can only require the locks in the atomic_check phase,
not in the commit phase. But since any commit is guaranteed to first
run the checks (even for the resume stuff where we use stored
duplicated old state) this should give us full coverage. Requested by
Maarten.
Cc: Jyri Sarha <jsarha@ti.com>
Fixes: a5b8444e289c ("drm/atomic-helper: remove modeset_lock_all from helper_resume")
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: Daniel Vetter <daniel.vetter@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20170531083813.1390-1-daniel.vetter@ffwll.ch
|
|
This is another attempt to work around the VLA used in
mixer_us16x08.c. Basically the temporary array is used individually
for two cases, and we can declare locally in each block, instead of
hackish max() usage.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
A mixer element created in a quirk for Tascam US-16x08 contains a
typo: it should be "EQ MidLow Q" instead of "EQ MidQLow Q".
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195875
Fixes: d2bb390a2081 ("ALSA: usb-audio: Tascam US-16x08 DSP mixer quirk")
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This reverts commit 89b593c30e83 ("ALSA: usb-audio: purge needless
variable length array"). The patch turned out to cause a severe
regression, triggering an Oops at snd_usb_ctl_msg(). It was overseen
that snd_usb_ctl_msg() writes back the response to the given buffer,
while the patch changed it to a read-only const buffer. (One should
always double-check when an extra pointer cast is present...)
As a simple fix, just revert the affected commit. It was merely a
cleanup. Although it brings VLA again, it's clearer as a fix. We'll
address the VLA later in another patch.
Fixes: 89b593c30e83 ("ALSA: usb-audio: purge needless variable length array")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=195875
Cc: <stable@vger.kernel.org> # v4.11+
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Force vop output mode on encoder driver seem not a good idea,
EDP, HDMI, DisplayPort all have 10bit input on rk3399,
On non-10bit vop, vop 8bit output bit[0-7] connect to the
encoder high 8bit [2-9].
So force RGB10 to RGB888 on vop driver would be better.
And another problem, EDP check crtc id on atomic_check,
but encoder maybe NULL, so out_mode configure would fail,
it cause edp no display.
Signed-off-by: Mark Yao <mark.yao@rock-chips.com>
Reviewed-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1495885416-22216-1-git-send-email-mark.yao@rock-chips.com
|
|
When the controller fails to provide an RPM reading within the alloted
time; the driver returns -ETIMEDOUT and no file contents.
Signed-off-by: Patrick Venture <venture@google.com>
Fixes: 2d7a548a3eff ("drivers: hwmon: Support for ASPEED PWM/Fan tach")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
The driver uses regmap and thus has to select it to avoid build
errors such as the following.
drivers/hwmon/aspeed-pwm-tacho.c:337:21: error: variable
'aspeed_pwm_tacho_regmap_config' has initializer but incomplete type
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Acked-by: Joel Stanley <joel@jms.id.au>
Fixes: 2d7a548a3eff ("drivers: hwmon: Support for ASPEED PWM/Fan tach")
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
This effectively reverts commit 8ee74a91ac30 ("proc: try to remove use
of FOLL_FORCE entirely")
It turns out that people do depend on FOLL_FORCE for the /proc/<pid>/mem
case, and we're talking not just debuggers. Talking to the affected people, the use-cases are:
Keno Fischer:
"We used these semantics as a hardening mechanism in the julia JIT. By
opening /proc/self/mem and using these semantics, we could avoid
needing RWX pages, or a dual mapping approach. We do have fallbacks to
these other methods (though getting EIO here actually causes an assert
in released versions - we'll updated that to make sure to take the
fall back in that case).
Nevertheless the /proc/self/mem approach was our favored approach
because it a) Required an attacker to be able to execute syscalls
which is a taller order than getting memory write and b) didn't double
the virtual address space requirements (as a dual mapping approach
would).
I think in general this feature is very useful for anybody who needs
to precisely control the execution of some other process. Various
debuggers (gdb/lldb/rr) certainly fall into that category, but there's
another class of such processes (wine, various emulators) which may
want to do that kind of thing.
Now, I suspect most of these will have the other process under ptrace
control, so maybe allowing (same_mm || ptraced) would be ok, but at
least for the sandbox/remote-jit use case, it would be perfectly
reasonable to not have the jit server be a ptracer"
Robert O'Callahan:
"We write to readonly code and data mappings via /proc/.../mem in lots
of different situations, particularly when we're adjusting program
state during replay to match the recorded execution.
Like Julia, we can add workarounds, but they could be expensive."
so not only do people use FOLL_FORCE for both reads and writes, but they
use it for both the local mm and remote mm.
With these comments in mind, we likely also cannot add the "are we
actively ptracing" check either, so this keeps the new code organization
and does not do a real revert that would add back the original comment
about "Maybe we should limit FOLL_FORCE to actual ptrace users?"
Reported-by: Keno Fischer <keno@juliacomputing.com>
Reported-by: Robert O'Callahan <robert@ocallahan.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
The tagset lock needs to be held when iterating the tag_list, so a
lockdep assert was added when updating number of hardware queues. The
drivers calling this API, however, were unaware of the new requirement,
so are failing the assertion.
This patch takes the lock within the blk-mq function so the drivers do
not have to be modified in order to be safe.
Fixes: 705cda97e ("blk-mq: Make it safe to use RCU to iterate over blk_mq_tag_set.tag_list")
Reported-by: Gabriel Krisman Bertazi <krisman@collabora.co.uk>
Reviewed-by: Bart Van Assche <Bart.VanAssche@sandisk.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Tariq Toukan says:
====================
MAINTAINERS updates
This patchset contains updates to the MAINTAINERS file.
In the first patch, I replace Yishai as the maintainer of
the mlx4_core driver.
In the other two patches we move an RDMA header file from
the list of the mlx4/mlx5 core driver into the respective
IB driver, where it belongs.
Series generated against net commit:
468b0df61a51 Merge git://git.kernel.org/pub/scm/linux/kernel/git/pablo/nf
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It belongs there, should not be under mlx5 Core driver.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It belongs there, should not be under mlx4 Core driver.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add myself as a maintainer for mlx4 core driver,
replacing Yishai Hadas.
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Building the driver with CONFIG_SMP disabled results in a harmless
warning:
ethernet/mellanox/mlx5/core/main.c: In function 'mlx5_irq_set_affinity_hint':
ethernet/mellanox/mlx5/core/main.c:615:6: error: unused variable 'irq' [-Werror=unused-variable]
It's better to express the conditional compilation using IS_ENABLED()
here, as that lets the compiler see what the intented use for the variable
is, and that it can be silently discarded.
Fixes: b665d98edc9a ("net/mlx5: Tolerate irq_set_affinity_hint() failures")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
'static' was not enough, the helpers must be 'static inline'
net/dsa/mv88e6xxx/global2.h:123:12: error: 'mv88e6xxx_g2_misc_4_bit_port' defined but not used [-Werror=unused-function]
net/dsa/mv88e6xxx/global2.h:117:12: error: 'mv88e6xxx_g2_pvt_write' defined but not used [-Werror=unused-function]
Fixes: c21fbe29f858 ("net: dsa: mv88e6xxx: Add missing static to stub functions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current implementation lacks the logic for providing management
firmware with RDMA-related statistics; [much] worse than that -
it logs such events by default to system logs.
Since the statistics' gathering is done periodically, using sufficiently
new management firmware the system logs would get filled with these
unnecessary prints.
For now, reduce the verbosity of the log so that it would not be
logged by default.
Fixes: 6c75424612a7 ("qed: Add support for NCSI statistics")
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During PCI error recovery process, specifically on eeh_err_detected()
we might have a NULL netdev struct, hence a direct dereference will
lead to a kernel oops. This was observed with latest upstream kernel
(v4.12-rc2) on Chelsio adapter T422-CR in PowerPC machines.
This patch checks for NULL pointer and avoids the crash, both in
eeh_err_detected() and eeh_resume(). Also, we avoid to trigger
a fatal error or to try disabling interrupts on FW during PCI
error recovery, because: (a) driver might not be able to accurately
access PCI regions in this case, and (b) trigger a fatal error
_during_ the recovery steps is a mistake that could prevent the
recovery path to complete successfully.
Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 19bca6ab75d8 ("KVM: SVM: Fix cross vendor migration issue with
unusable bit") added checking type when setting unusable.
So unusable can be set if present is 0 OR type is 0.
According to the AMD processor manual, long mode ignores the type value
in segment descriptor. And type can be 0 if it is read-only data segment.
Therefore type value is not related to unusable flag.
This patch is based on linux-next v4.12.0-rc3.
Signed-off-by: Gioh Kim <gi-oh.kim@profitbricks.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
kvm_skip_emulated_instruction() will return 0 if userspace is
single-stepping the guest.
kvm_skip_emulated_instruction() uses return status convention of exit
handler: 0 means "exit to userspace" and 1 means "continue vm entries".
The problem is that nested_vmx_check_vmptr() return status means
something else: 0 is ok, 1 is error.
This means we would continue executing after a failure. Static checker
noticed it because vmptr was not initialized.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 6affcbedcac7 ("KVM: x86: Add kvm_skip_emulated_instruction and use it.")
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
nbd_config is allocated in nbd_alloc_config(), but never freed.
Fixes: 5ea8d10802ec ("nbd: separate out the config information")
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
There is nothing to clear -- nbd_device has just been allocated.
Fold nbd_reset() into its other caller, nbd_config_put().
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Josef Bacik <jbacik@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
We saw perf IRQ init failures when running Linux kernel in an ACPI
guest without PMU (i.e. pmu=off). This is because perf IRQ is not
present when pmu=off, but arm_pmu_acpi still tries to register
or unregister GSI. This patch addresses the problem by checking
gicc->performance_interrupt. If it is 0, which is the value set
by qemu when pmu=off, we skip the IRQ register/unregister process.
[ 4.069470] bc00: 0000000000040b00 ffff0000089db190
[ 4.070267] [<ffff000008134f80>] enable_percpu_irq+0xdc/0xe4
[ 4.071192] [<ffff000008667cc4>] arm_perf_starting_cpu+0x108/0x10c
[ 4.072200] [<ffff0000080cbdd4>] cpuhp_invoke_callback+0x14c/0x4ac
[ 4.073210] [<ffff0000080ccd3c>] cpuhp_thread_fun+0xd4/0x11c
[ 4.074132] [<ffff0000080f1394>] smpboot_thread_fn+0x1b4/0x1c4
[ 4.075081] [<ffff0000080ec90c>] kthread+0x10c/0x138
[ 4.075921] [<ffff0000080833c0>] ret_from_fork+0x10/0x50
[ 4.076947] genirq: Setting trigger mode 4 for irq 43 failed
(gic_set_type+0x0/0x74)
Signed-off-by: Wei Huang <wei@redhat.com>
[will: add comment justifying deviation from ACPI spec, removed redundant hunk]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Add device-tree files relevant to TI DaVinci platform
to its entry so mach-davinci sub-arch maintainers get
copied on patches with device-tree file updates.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
arch_teardown_dma_ops() being the inverse of arch_setup_dma_ops()
,dma_ops should be cleared in the teardown path. Currently, only the
device's iommu mapping structures are cleared in arch_teardown_dma_ops,
but not the dma_ops. So on the next reprobe, dma_ops left in place is
stale from the first IOMMU setup, but iommu mappings has been disposed
of. This is a problem when the probe of the device is deferred and
recalled with the IOMMU probe deferral.
So for fixing this, slightly refactor by moving the code from
__arm_iommu_detach_device to arm_iommu_detach_device and cleanup
the former. This takes care of resetting the dma_ops in the teardown
path.
Fixes: 09515ef5ddad ("of/acpi: Configure dma operations at probe time for platform/amba/pci bus devices")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
With IOMMU probe deferral, iort_iommu_configure can be called
multiple times for the same device. Hence we have a check
to see if the device's fwspec is already translated and return
the iommu_ops from that directly. But the check is wrongly
placed in iort_iommu_xlate, which breaks devices with multiple
sids. Move the check to iort_iommu_configure.
Fixes: 5a1bb638d567 ("drivers: acpi: Handle IOMMU lookup failure with deferred probing or error")
Tested-by: Nate Watterson <nwatters@codeaurora.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
arch_setup_dma_ops() is used in device probe code paths to create an
IOMMU mapping and attach it to the device. The function assumes that the
device is attached to a device-specific IOMMU instance (or at least a
device-specific TLB in a shared IOMMU instance) and thus creates a
separate mapping for every device.
On several systems (Renesas R-Car Gen2 being one of them), that
assumption is not true, and IOMMU mappings must be shared between
multiple devices. In those cases the IOMMU driver knows better than the
generic ARM dma-mapping layer and attaches mapping to devices manually
with arm_iommu_attach_device(), which sets the DMA ops for the device.
The arch_setup_dma_ops() function takes this into account and bails out
immediately if the device already has DMA ops assigned. However, the
corresponding arch_teardown_dma_ops() function, called from driver
unbind code paths (including probe deferral), will tear the mapping down
regardless of who created it. When the device is reprobed
arch_setup_dma_ops() will be called again but won't perform any
operation as the DMA ops will still be set.
We need to reset the DMA ops in arch_teardown_dma_ops() to fix this.
However, we can't do so unconditionally, as then a new mapping would be
created by arch_setup_dma_ops() when the device is reprobed, regardless
of whether the device needs to share a mapping or not. We must thus keep
track of whether arch_setup_dma_ops() created the mapping, and only in
that case tear it down in arch_teardown_dma_ops().
Keep track of that information in the dev_archdata structure. As the
structure is embedded in all instances of struct device let's not grow
it, but turn the existing dma_coherent bool field into a bitfield that
can be used for other purposes.
Fixes: 09515ef5ddad ("of/acpi: Configure dma operations at probe time for platform/amba/pci bus devices")
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
While deferring the probe of IOMMU masters, xlate and
add_device callbacks called from iort_iommu_configure
can pass back error values like -ENODEV, which means
the IOMMU cannot be connected with that master for real
reasons. Before the IOMMU probe deferral, all such errors
were ignored. Now all those errors are propagated back,
killing the master's probe for such errors. Instead ignore
all the errors except EPROBE_DEFER, which is the only one
of concern and let the master work without IOMMU, thus
restoring the old behavior. Also make explicit that
acpi_dma_configure handles only -EPROBE_DEFER from
iort_iommu_configure.
Fixes: 5a1bb638d567 ("drivers: acpi: Handle IOMMU lookup failure with deferred probing or error")
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
While deferring the probe of IOMMU masters, xlate and
add_device callbacks called from of_iommu_configure
can pass back error values like -ENODEV, which means
the IOMMU cannot be connected with that master for real
reasons. Before the IOMMU probe deferral, all such errors
were ignored. Now all those errors are propagated back,
killing the master's probe for such errors. Instead ignore
all the errors except EPROBE_DEFER, which is the only one
of concern and let the master work without IOMMU, thus
restoring the old behavior. Also make explicit that
of_dma_configure handles only -EPROBE_DEFER from
of_iommu_configure.
Fixes: 7b07cbefb68d ("iommu: of: Handle IOMMU lookup failure with deferred probing or error")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Magnus Damn <magnus.damn@gmail.com>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Now with IOMMU probe deferral, we return -EPROBE_DEFER
for masters that are connected to an IOMMU which is not
probed yet, but going to get probed, so that we can attach
the correct dma_ops. So while trying to defer the probe of
the master, check if the of_iommu node that it is connected
to is marked in DT as 'status=disabled', then the IOMMU is never
is going to get probed. So simply return NULL and let the master
work without an IOMMU.
Fixes: 7b07cbefb68d ("iommu: of: Handle IOMMU lookup failure with deferred probing or error")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Will Deacon <will.deacon@arm.com>
Tested-by: Magnus Damn <magnus.damn@gmail.com>
Acked-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Sricharan R <sricharan@codeaurora.org>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Newly added code in the ipmmu-vmsa driver showed a small mistake
in a header file that can't be included by itself without CONFIG_IOMMU_DMA
enabled:
In file included from drivers/iommu/ipmmu-vmsa.c:13:0:
include/linux/dma-iommu.h:105:94: error: 'struct device' declared inside parameter list will not be visible outside of this definition or declaration [-Werror]
This adds a forward declaration for 'struct device', similar to how
we treat the other struct types in this case.
Fixes: 3ae47292024f ("iommu/ipmmu-vmsa: Add new IOMMU_DOMAIN_DMA ops")
Fixes: 273df9635385 ("iommu/dma: Make PCI window reservation generic")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
When starting or stopping an aggregation session, one of the steps
is that the driver calls back to mac80211 that the start/stop can
proceed. This is handled by queueing up a fake SKB and processing
it from the normal iface/sdata work. Since this isn't flushed when
disassociating, the following race is possible:
* associate
* start aggregation session
* driver callback
* disassociate
* associate again to the same AP
* callback processing runs, leading to a WARN_ON() that
the TID hadn't requested aggregation
If the second association isn't to the same AP, there would only
be a message printed ("Could not find station: <addr>"), but the
same race could happen.
Fix this by not going the whole detour with a fake SKB etc. but
simply looking up the aggregation session in the driver callback,
marking it with a START_CB/STOP_CB bit and then scheduling the
regular aggregation work that will now process these bits as well.
This also simplifies the code and gets rid of the whole problem
with allocation failures of said skb, which could have left the
session in limbo.
Reported-by: Jouni Malinen <j@w1.fi>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
In descriptor mode, the descriptor running pointer is not maintained
by the interrupt handler, thus, driver finds the running descriptor
from the descriptor pointer field in the CHCRB register.
But, CHCRB::DPTR indicates *next* descriptor pointer, not current.
Thus, The residue calculation will be missed. This patch fixup it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
Pablo Neira Ayuso says:
====================
Netfilter fixes for net
The following patchset contains Netfilter fixes for your net tree,
they are:
1) Conntrack SCTP CRC32c checksum mangling may operate on non-linear
skbuff, patch from Davide Caratti.
2) nf_tables rb-tree set backend does not handle element re-addition
after deletion in the same transaction, leading to infinite loop.
3) Atomically unclear the IPS_SRC_NAT_DONE_BIT on nat module removal,
from Liping Zhang.
4) Conntrack hashtable resizing while ctnetlink dump is progress leads
to a dead reference to released objects in the lists, also from
Liping.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Users should really consider switching to rmi-smbus instead of plain PS/2.
Notify them that they should report a missing pnpID in the file.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The Synaptics touchpads are now either using i2c-hid or rmi-smbus.
Warn the users if they are missing the rmi-smbus modules and have no
chance of reporting correct data.
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Or the user might have the touchpad unbound from PS/2 but never picked
up by rmi-smbus.ko
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
synaptics_query_hardware() was being passed a 'struct synaptics_device_info'
in uninitialized stack memory, then not always initializing all fields.
This caused garbage to show up in certain fields, making the touchpad
unusable.
Fix by zeroing the device info, so all fields default to 0.
Fixes: 6c53694fb222 ("Input: synaptics - split device info into a separate structure")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
When we put the touchscreen controller in low-power mode the irq
pin may trigger (float) and if we then try to read a data packet we
get the following error in dmesg:
[ 478.801017] silead_ts i2c-MSSL1680:00: Data read error -121
This commit disables the irq during suspend/resume fixing this error.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
For a driver that does not set the CPUFREQ_STICKY flag, if all of the
->init() calls fail, cpufreq_register_driver() should return an error.
This will prevent the driver from loading.
Fixes: ce1bcfe94db8 (cpufreq: check cpufreq_policy_list instead of scanning policies for all CPUs)
Cc: 4.0+ <stable@vger.kernel.org> # 4.0+
Signed-off-by: David Arcari <darcari@redhat.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In the Linux kernel, acpi_get_table() "clones" haven't been fully
balanced by acpi_put_table() invocations. In upstream ACPICA, due to
the design change, there are also unbalanced acpi_get_table_by_index()
invocations requiring special care.
acpi_get_table() reference counting mismatches may occor due to that
and printing error messages related to them is not useful at this
point. The strict balanced validation count check should only be
enabled after confirming that all invocations are safe and aligned
with their designed purposes.
Thus this patch removes the error value returned by acpi_tb_get_table()
in that case along with the accompanying error message to fix the
issue.
Fixes: 174cc7187e6f (ACPICA: Tables: Back port acpi_get_table_with_size() and early_acpi_os_unmap_memory() from Linux kernel)
Cc: 4.10+ <stable@vger.kernel.org> # 4.10+
Reported-by: Anush Seetharaman <anush.seetharaman@intel.com>
Reported-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
[ rjw: Changelog ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
