| Age | Commit message (Collapse) | Author |
|---|
|
dnrmg_receive_user_skb"
This reverts commit 85eac2ba35a2dbfbdd5767c7447a4af07444a5b4.
There is an updated version of this fix which we should
use instead.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
emac_mdio_read_link() was not copying the requested phy settings
back into the emac driver's own phy api. This has caused a link
speed mismatch issue for the AR8035 as the emac driver kept
trying to connect with 10/100MBps on a 1GBit/s link.
This patch also unifies shared code between emac_setup_aneg()
and emac_mdio_setup_forced(). And furthermore it removes
a chunk of emac_mdio_init_phy(), that was copying the same
data into itself.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a problem where the AR8035 PHY can't be
detected on an Cisco Meraki MR24, if the ethernet cable is
not connected on boot.
Russell Senior provided steps to reproduce the issue:
|Disconnect ethernet cable, apply power, wait until device has booted,
|plug in ethernet, check for interfaces, no eth0 is listed.
|
|This appears to be a problem during probing of the AR8035 Phy chip.
|When ethernet has no link, the phy detection fails, and eth0 is not
|created. Plugging ethernet later has no effect, because there is no
|interface as far as the kernel is concerned. The relevant part of
|the boot log looks like this:
|this is the failing case:
|
|[ 0.876611] /plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode
|[ 0.882532] /plb/opb/ethernet@ef600c00: reset timeout
|[ 0.888546] /plb/opb/ethernet@ef600c00: can't find PHY!
|and the succeeding case:
|
|[ 0.876672] /plb/opb/emac-rgmii@ef601500: input 0 in RGMII mode
|[ 0.883952] eth0: EMAC-0 /plb/opb/ethernet@ef600c00, MAC 00:01:..
|[ 0.890822] eth0: found Atheros 8035 Gigabit Ethernet PHY (0x01)
Based on the comment and the commit message of
commit 23fbb5a87c56 ("emac: Fix EMAC soft reset on 460EX/GT").
This is because the AR8035 PHY doesn't provide the TX Clock,
if the ethernet cable is not attached. This causes the reset
to timeout and the PHY detection code in emac_init_phy() is
unable to detect the AR8035 PHY. As a result, the emac driver
bails out early and the user left with no ethernet.
In order to stay compatible with existing configurations, the driver
tries the current reset approach at first. Only if the first attempt
timed out, it does perform one more retry with the clock temporarily
switched to the internal source for just the duration of the reset.
LEDE-Bug: #687 <https://bugs.lede-project.org/index.php?do=details&task_id=687>
Cc: Chris Blake <chrisrblake93@gmail.com>
Reported-by: Russell Senior <russell@personaltelco.net>
Fixes: 23fbb5a87c56e98 ("emac: Fix EMAC soft reset on 460EX/GT")
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Verify that the length of the socket buffer is sufficient to cover the
entire nlh->nlmsg_len field before accessing that field for further
input sanitization. If the client only supplies 1-3 bytes of data in
sk_buff, then nlh->nlmsg_len remains partially uninitialized and
contains leftover memory from the corresponding kernel allocation.
Operating on such data may result in indeterminate evaluation of the
nlmsg_len < sizeof(*nlh) expression.
The bug was discovered by a runtime instrumentation designed to detect
use of uninitialized memory in the kernel. The patch prevents this and
other similar tools (e.g. KMSAN) from flagging this behavior in the future.
Signed-off-by: Mateusz Jurczyk <mjurczyk@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux into HEAD
KVM: s390: Fix for master (4.12)
- The newly created AIS capability enables the feature unconditionally
and ignores the cpu model
|
|
Christoph writes:
"A few NVMe fixes for 4.12-rc, PCIe reset fixes and APST fixes, a
RDMA reconnect fix, two FC fixes and a general controller removal fix."
|
|
> ../drivers/hsi/clients/ssi_protocol.c:1069:5: error: 'struct net_device' has no member named 'destructor'
Reported-by: Mark Brown <broonie@kernel.org>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
netdev state"
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/gpu/drm/i915/intel_engine_cs.c: In function ‘intel_engine_is_idle’:
drivers/gpu/drm/i915/intel_engine_cs.c:1103:27: error: unused variable ‘dev_priv’ [-Werror=unused-variable]
struct drm_i915_private *dev_priv = engine->i915;
^~~~~~~~
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
While installing SLES-12 (based on v4.4), I found that the installer
will stall for 60+ seconds during LVM disk scan. The root cause was
determined to be the removal of a bound device check in loop_flush()
by commit b5dd2f6047ca ("block: loop: improve performance via blk-mq").
Restoring this check, examining ->lo_state as set by loop_set_fd()
eliminates the bad behavior.
Test method:
modprobe loop max_loop=64
dd if=/dev/zero of=disk bs=512 count=200K
for((i=0;i<4;i++))do losetup -f disk; done
mkfs.ext4 -F /dev/loop0
for((i=0;i<4;i++))do mkdir t$i; mount /dev/loop$i t$i;done
for f in `ls /dev/loop[0-9]*|sort`; do \
echo $f; dd if=$f of=/dev/null bs=512 count=1; \
done
Test output: stock patched
/dev/loop0 18.1217e-05 8.3842e-05
/dev/loop1 6.1114e-05 0.000147979
/dev/loop10 0.414701 0.000116564
/dev/loop11 0.7474 6.7942e-05
/dev/loop12 0.747986 8.9082e-05
/dev/loop13 0.746532 7.4799e-05
/dev/loop14 0.480041 9.3926e-05
/dev/loop15 1.26453 7.2522e-05
Note that from loop10 onward, the device is not mounted, yet the
stock kernel consumes several orders of magnitude more wall time
than it does for a mounted device.
(Thanks for Mike Galbraith <efault@gmx.de>, give a changelog review.)
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: James Wang <jnwang@suse.com>
Fixes: b5dd2f6047ca ("block: loop: improve performance via blk-mq")
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
We need to push the chain index down to the drivers, so they have the
information to which chain the rule belongs. For now, no driver supports
multichain offload, so only chain 0 is supported. This is needed to
prevent chain squashes during offload for now. Later this will be used
to implement multichain offload.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
|
|
When ftrace is used with kprobes, it is possible for a kprobe to contain
an invalid location (ie. only initialised to 0 and not to a specific
location in the code). Trying to perform a cache flush on such location
leads to a crash r4k_flush_icache_range().
Fixes: c1bf207d6ee1 ("MIPS: kprobe: Add support.")
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16296/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
If "i" is the last element in the vcpu->arch.cpuid_entries[] array, it
potentially can be exploited the vulnerability. this will out-of-bounds
read and write. Luckily, the effect is small:
/* when no next entry is found, the current entry[i] is reselected */
for (j = i + 1; ; j = (j + 1) % nent) {
struct kvm_cpuid_entry2 *ej = &vcpu->arch.cpuid_entries[j];
if (ej->function == e->function) {
It reads ej->maxphyaddr, which is user controlled. However...
ej->flags |= KVM_CPUID_FLAG_STATE_READ_NEXT;
After cpuid_entries there is
int maxphyaddr;
struct x86_emulate_ctxt emulate_ctxt; /* 16-byte aligned */
So we have:
- cpuid_entries at offset 1B50 (6992)
- maxphyaddr at offset 27D0 (6992 + 3200 = 10192)
- padding at 27D4...27DF
- emulate_ctxt at 27E0
And it writes in the padding. Pfew, writing the ops field of emulate_ctxt
would have been much worse.
This patch fixes it by modding the index to avoid the out-of-bounds
access. Worst case, i == j and ej->function == e->function,
the loop can bail out.
Reported-by: Moguofang <moguofang@huawei.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Guofang Mo <moguofang@huawei.com>
Cc: stable@vger.kernel.org
Signed-off-by: Wanpeng Li <wanpeng.li@hotmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/ARM Fixes for v4.12-rc5 - Take 2
Changes include:
- Fix an issue with migrating GICv2 VMs on GICv3 systems.
- Squashed a bug for gicv3 when figuring out preemption levels.
- Fix a potential null pointer derefence in KVM happening under memory
pressure.
- Maintain RES1 bits in the SCTLR_EL2 to make sure KVM works on new
architecture revisions.
- Allow unaligned accesses at EL2/HYP
|
|
Since introduction of tracing for init functions the in_kernel_space()
check is no longer correct, as it ignores the init sections. As a
result, when probes are inserted (and disabled) in the init functions,
a branch instruction is inserted instead of a nop, which is likely to
result in random crashes during boot.
Remove the MIPS-specific in_kernel_space() method and replace it with a
generic core_kernel_text() that also checks for init sections during
system boot stage.
Fixes: 42c269c88dc1 ("ftrace: Allow for function tracing to record init functions on boot up")
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Tested-by: Matt Redfearn <matt.redfearn@imgtec.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/16092/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Space reserved for PKMap should span from PKMAP_BASE to FIXADDR_START.
For large page sizes this is not the case as eg. for 64k pages the range
currently defined is from 0xfe000000 to 0x102000000(!!) which obviously
isn't right.
Remove the hardcoded location and set the BASE address as an offset from
FIXADDR_START.
Since all PKMAP ptes have to be placed in a contiguous memory, ensure
that this is the case by placing them all in a single page. This is
achieved by aligning the end address to pkmap pages count pages.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15950/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
All PTEs used by PKMAP should be allocated in a contiguous memory area,
but we do not currently have a mechanism to enforce that, so ensure that
we don't try to allocate more entries than would fit in a single page.
Current fixed value of 1024 would not work with XPA enabled when
sizeof(pte_t)==8 and we need two pages to store pte tables.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15949/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
fixrange_init operates at PMD-granularity and expects the addresses to
be PMD-size aligned, but currently that might not be the case for
PKMAP_BASE unless it is defined properly, so ensure a correct alignment
is used before passing the address to fixrange_init.
fixed mappings: only align the start address that is passed to
fixrange_init rather than the value before adding the size, as we may
end up with uninitialised upper part of the range.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15948/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
All performance counters on I6400 (odd and even) are capable of counting
any of the available events, so drop current logic of using the extra
bit to determine which counter to use.
Signed-off-by: Marcin Nowakowski <marcin.nowakowski@imgtec.com>
Fixes: 4e88a8621301 ("MIPS: Add cases for CPU_I6400")
Fixes: fd716fca10fc ("MIPS: perf: Fix I6400 event numbers")
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/15991/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Instead of using the SKB queue with the fake pkt_type for the
offloaded RX BA session management, also handle this with the
normal aggregation state machine worker. This also makes the
use of this more reliable since it gets rid of the allocation
of the fake skb.
Combined with the previous patch, this finally allows us to
get rid of the pkt_type hack entirely, so do that as well.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This brings in commit 7a7c0a6438b8 ("mac80211: fix TX aggregation
start/stop callback race") to allow the follow-up cleanup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Translate hardware port connector type data into link mode supported and
advertised info instead of caching it in driver.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Read port connector type from the firmware instead of caching it in the
driver metadata.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Update struct mlx5_ifc_create(modify)_flow_table_bits according to
the last device specification.
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Using a per field mask field, the TC pedit action supports modifying
partial fields. E.g if using the TC tool, the following example would
make the kernel to only re-write two bytes of the src ip address:
tc filter add dev enp1s0 protocol ip parent ffff: prio 30
flower skip_sw ip_proto udp dst_port 8001
action pedit ex munge ip src set 10.1.0.0 retain 0xffff0000
We add driver support for offload these partial re-writes, by setting
the per FW action offset-in-field and length-from-offset attributes.
The 1st bit set in the mask specifies both the offset and the right
shift to apply on the value such that the 1st bit which needs to be
set will reside in bit 0 of the FW data field.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Use the modify header ID cache for the header re-write part of offloading
TC NIC flows.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Use the modify header ID cache for the header re-write part of offloading
TC eswitch flows.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Packets belonging to flows which are different by matching may still need
to go through the same header re-write. Add a cache for header re-write IDs
keyed by the binary chain of modify header actions.
The caching is supported for both eswitch and NIC use-cases, where the
actual conversion of the code to use caching comes in next patches, one
per use-case.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Instead of going through flow->nic/esw_attr for each usage, assign
an attr pointer per the context (nic or esw) and use that.
This patch doesn't add any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Remove the limitation that offloaded NIC filters can have only one
action. This allows us for example to provide flow tag as a note
to upper layers / apps that that HW header re-write was applied.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The PPC_DT_CPU_FTRs is a bit misplaced in menuconfig, it shows up with
other general kernel options. It's really more at home in the "Platform
Support" section, so move it there.
Also enable it by default, for Book3s 64. It does mostly nothing unless
the device tree properties are found, and we will want it enabled
eventually in distro kernels, so turn it on to start getting more
testing.
Fixes: 5a61ef74f269 ("powerpc/64s: Support new device tree binding for discovering CPU features")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Supporting 512TB requires us to do a order 3 allocation for level 1 page
table (pgd). This results in page allocation failures with certain workloads.
For now limit 4k linux page size config to 64TB.
Fixes: f6eedbba7a26 ("powerpc/mm/hash: Increase VA range to 128TB")
Reported-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Fix error path if we can't copy user structure on CXL_IOCTL_START_WORK
ioctl. We shouldn't unlock the context status mutex as it was not
locked (yet).
Fixes: 0712dc7e73e5 ("cxl: Fix issues when unmapping contexts")
Cc: stable@vger.kernel.org # v3.19+
Signed-off-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Reviewed-by: Vaibhav Jain <vaibhav@linux.vnet.ibm.com>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When calling CEC_RECEIVE do not check if the adapter is configured.
Typically CEC_RECEIVE is called after a select() and if that indicates
that there are messages in the receive queue, then you should always be
able to dequeue a message.
The race condition here is that a message has been received and is
queued, so select() tells userspace that a message is available. But
before the application calls CEC_RECEIVE the adapter is unconfigured
(e.g. the HDMI cable is removed). Now select will always report that
there is a message, but calling CEC_RECEIVE will always return -ENONET
because the adapter is no longer configured and so will never actually
dequeue the message.
There is really no need for this check, and in fact the ENONET error
code was never documented for CEC_RECEIVE. This may have been a left-over
of old code that was never updated.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v4.10 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
This reverts commit cf39bf58afdaabc0b86f141630fb3fd18190294e.
The commit regression to users that define both console=ttyS1
and console=ttyS0 on the command line, see
https://lkml.kernel.org/r/20170509082915.GA13236@bistromath.localdomain
The kernel log messages always appeared only on one serial port. It is
even documented in Documentation/admin-guide/serial-console.rst:
"Note that you can only define one console per device type (serial,
video)."
The above mentioned commit changed the order in which the command line
parameters are searched. As a result, the kernel log messages go to
the last mentioned ttyS* instead of the first one.
We long thought that using two console=ttyS* on the command line
did not make sense. But then we realized that console= parameters
were handled also by systemd, see
http://0pointer.de/blog/projects/serial-console.html
"By default systemd will instantiate one serial-getty@.service on
the main kernel console, if it is not a virtual terminal."
where
"[4] If multiple kernel consoles are used simultaneously, the main
console is the one listed first in /sys/class/tty/console/active,
which is the last one listed on the kernel command line."
This puts the original report into another light. The system is running
in qemu. The first serial port is used to store the messages into a file.
The second one is used to login to the system via a socket. It depends
on systemd and the historic kernel behavior.
By other words, systemd causes that it makes sense to define both
console=ttyS1 console=ttyS0 on the command line. The kernel fix
caused regression related to userspace (systemd) and need to be
reverted.
In addition, it went out that the fix helped only partially.
The messages still were duplicated when the boot console was
removed early by late_initcall(printk_late_init). Then the entire
log was replayed when the same console was registered as a normal one.
Link: 20170606160339.GC7604@pathway.suse.cz
Cc: Aleksey Makarov <aleksey.makarov@linaro.org>
Cc: Sabrina Dubroca <sd@queasysnail.net>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Jiri Slaby <jslaby@suse.com>
Cc: Robin Murphy <robin.murphy@arm.com>,
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: "Nair, Jayachandran" <Jayachandran.Nair@cavium.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Reported-by: Sabrina Dubroca <sd@queasysnail.net>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
|
|
On sparc, if we have an alloca() like situation, as is the case with
SHASH_DESC_ON_STACK(), we can end up referencing deallocated stack
memory. The result can be that the value is clobbered if a trap
or interrupt arrives at just the right instruction.
It only occurs if the function ends returning a value from that
alloca() area and that value can be placed into the return value
register using a single instruction.
For example, in lib/libcrc32c.c:crc32c() we end up with a return
sequence like:
return %i7+8
lduw [%o5+16], %o0 ! MEM[(u32 *)__shash_desc.1_10 + 16B],
%o5 holds the base of the on-stack area allocated for the shash
descriptor. But the return released the stack frame and the
register window.
So if an intererupt arrives between 'return' and 'lduw', then
the value read at %o5+16 can be corrupted.
Add a data compiler barrier to work around this problem. This is
exactly what the gcc fix will end up doing as well, and it absolutely
should not change the code generated for other cpus (unless gcc
on them has the same bug :-)
With crucial insight from Eric Sandeen.
Cc: <stable@vger.kernel.org>
Reported-by: Anatoly Pugachev <matorola@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When doing sampling, for example:
perf record -e cycles:u ...
On workloads that do a lot of kernel entry/exits we see kernel
samples, even though :u is specified. This is due to skid existing.
This might be a security issue because it can leak kernel addresses even
though kernel sampling support is disabled.
The patch drops the kernel samples if exclude_kernel is specified.
For example, test on Haswell desktop:
perf record -e cycles:u <mgen>
perf report --stdio
Before patch applied:
99.77% mgen mgen [.] buf_read
0.20% mgen mgen [.] rand_buf_init
0.01% mgen [kernel.vmlinux] [k] apic_timer_interrupt
0.00% mgen mgen [.] last_free_elem
0.00% mgen libc-2.23.so [.] __random_r
0.00% mgen libc-2.23.so [.] _int_malloc
0.00% mgen mgen [.] rand_array_init
0.00% mgen [kernel.vmlinux] [k] page_fault
0.00% mgen libc-2.23.so [.] __random
0.00% mgen libc-2.23.so [.] __strcasestr
0.00% mgen ld-2.23.so [.] strcmp
0.00% mgen ld-2.23.so [.] _dl_start
0.00% mgen libc-2.23.so [.] sched_setaffinity@@GLIBC_2.3.4
0.00% mgen ld-2.23.so [.] _start
We can see kernel symbols apic_timer_interrupt and page_fault.
After patch applied:
99.79% mgen mgen [.] buf_read
0.19% mgen mgen [.] rand_buf_init
0.00% mgen libc-2.23.so [.] __random_r
0.00% mgen mgen [.] rand_array_init
0.00% mgen mgen [.] last_free_elem
0.00% mgen libc-2.23.so [.] vfprintf
0.00% mgen libc-2.23.so [.] rand
0.00% mgen libc-2.23.so [.] __random
0.00% mgen libc-2.23.so [.] _int_malloc
0.00% mgen libc-2.23.so [.] _IO_doallocbuf
0.00% mgen ld-2.23.so [.] do_lookup_x
0.00% mgen ld-2.23.so [.] open_verify.constprop.7
0.00% mgen ld-2.23.so [.] _dl_important_hwcaps
0.00% mgen libc-2.23.so [.] sched_setaffinity@@GLIBC_2.3.4
0.00% mgen ld-2.23.so [.] _start
There are only userspace symbols.
Signed-off-by: Jin Yao <yao.jin@linux.intel.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: acme@kernel.org
Cc: jolsa@kernel.org
Cc: kan.liang@intel.com
Cc: mark.rutland@arm.com
Cc: will.deacon@arm.com
Cc: yao.jin@intel.com
Link: http://lkml.kernel.org/r/1495706947-3744-1-git-send-email-yao.jin@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
During early boot, load_ucode_intel_ap() uses __load_ucode_intel()
to obtain a pointer to the relevant microcode patch (embedded in the
initrd), and stores this value in 'intel_ucode_patch' to speed up the
microcode patch application for subsequent CPUs.
On resuming from suspend-to-RAM, however, load_ucode_ap() calls
load_ucode_intel_ap() for each non-boot-CPU. By then the initramfs is
long gone so the pointer stored in 'intel_ucode_patch' no longer points to
a valid microcode patch.
Clear that pointer so that we effectively fall back to the CPU hotplug
notifier callbacks to update the microcode.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
[ Edit and massage commit message. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org> # 4.10..
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/20170607095819.9754-1-bp@alien8.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
I will be traveling in the upcoming months and it'll be much easier for me
to access my kernel.org email rather than my work one. Change my email
address in the MAINTAINERS file from jeyu@redhat.com to jeyu@kernel.org.
Signed-off-by: Jessica Yu <jeyu@redhat.com>
|
|
An error during suspend (e100e_pm_suspend),
[ 429.994338] ACPI : EC: event blocked
[ 429.994633] e1000e: EEE TX LPI TIMER: 00000011
[ 430.955451] pci_pm_suspend(): e1000e_pm_suspend+0x0/0x30 [e1000e] returns -2
[ 430.955454] dpm_run_callback(): pci_pm_suspend+0x0/0x140 returns -2
[ 430.955458] PM: Device 0000:00:19.0 failed to suspend async: error -2
[ 430.955581] PM: Some devices failed to suspend, or early wake event detected
[ 430.957709] ACPI : EC: event unblocked
lead to complete failure:
[ 432.585002] ------------[ cut here ]------------
[ 432.585013] WARNING: CPU: 3 PID: 8372 at kernel/irq/manage.c:1478 __free_irq+0x9f/0x280
[ 432.585015] Trying to free already-free IRQ 20
[ 432.585016] Modules linked in: cdc_ncm usbnet x86_pkg_temp_thermal intel_powerclamp coretemp mii crct10dif_pclmul crc32_pclmul ghash_clmulni_intel snd_hda_codec_hdmi snd_hda_codec_realtek snd_hda_codec_generic snd_hda_intel snd_hda_codec snd_hwdep lpc_ich snd_hda_core snd_pcm mei_me mei sdhci_pci sdhci i915 mmc_core e1000e ptp pps_core prime_numbers
[ 432.585042] CPU: 3 PID: 8372 Comm: kworker/u16:40 Tainted: G U 4.10.0-rc8-CI-Patchwork_3870+ #1
[ 432.585044] Hardware name: LENOVO 2356GCG/2356GCG, BIOS G7ET31WW (1.13 ) 07/02/2012
[ 432.585050] Workqueue: events_unbound async_run_entry_fn
[ 432.585051] Call Trace:
[ 432.585058] dump_stack+0x67/0x92
[ 432.585062] __warn+0xc6/0xe0
[ 432.585065] warn_slowpath_fmt+0x4a/0x50
[ 432.585070] ? _raw_spin_lock_irqsave+0x49/0x60
[ 432.585072] __free_irq+0x9f/0x280
[ 432.585075] free_irq+0x34/0x80
[ 432.585089] e1000_free_irq+0x65/0x70 [e1000e]
[ 432.585098] e1000e_pm_freeze+0x7a/0xb0 [e1000e]
[ 432.585106] e1000e_pm_suspend+0x21/0x30 [e1000e]
[ 432.585113] pci_pm_suspend+0x71/0x140
[ 432.585118] dpm_run_callback+0x6f/0x330
[ 432.585122] ? pci_pm_freeze+0xe0/0xe0
[ 432.585125] __device_suspend+0xea/0x330
[ 432.585128] async_suspend+0x1a/0x90
[ 432.585132] async_run_entry_fn+0x34/0x160
[ 432.585137] process_one_work+0x1f4/0x6d0
[ 432.585140] ? process_one_work+0x16e/0x6d0
[ 432.585143] worker_thread+0x49/0x4a0
[ 432.585145] kthread+0x107/0x140
[ 432.585148] ? process_one_work+0x6d0/0x6d0
[ 432.585150] ? kthread_create_on_node+0x40/0x40
[ 432.585154] ret_from_fork+0x2e/0x40
[ 432.585156] ---[ end trace 6712df7f8c4b9124 ]---
The unwind failures stems from commit 2800209994f8 ("e1000e: Refactor PM
flows"), but it may be a later patch that introduced the non-recoverable
behaviour.
Fixes: 2800209994f8 ("e1000e: Refactor PM flows")
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=99847
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Clean up a few sparse warnings, these following
functions can be made static:
drivers/net/ethernet/intel/igb/igb_main.c: warning: symbol
'igb_add_mac_filter' was not declared. Should it be static?
drivers/net/ethernet/intel/igb/igb_main.c: warning: symbol
'igb_del_mac_filter' was not declared. Should it be static?
drivers/net/ethernet/intel/igb/igb_main.c: warning: symbol
'igb_set_vf_mac_filter' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
It's possible that get_random_{u32,u64} is used before the crng has
initialized, in which case, its output might not be cryptographically
secure. For this problem, directly, this patch set is introducing the
*_wait variety of functions, but even with that, there's a subtle issue:
what happens to our batched entropy that was generated before
initialization. Prior to this commit, it'd stick around, supplying bad
numbers. After this commit, we force the entropy to be re-extracted
after each phase of the crng has initialized.
In order to avoid a race condition with the position counter, we
introduce a simple rwlock for this invalidation. Since it's only during
this awkward transition period, after things are all set up, we stop
using it, so that it doesn't have an impact on performance.
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Cc: stable@vger.kernel.org # v4.11+
|
|
Few shell command examples in perf-script-python.txt has few nitpicks
include:
- tools/perf/scripts/python directory listing command is unnecessarily
repeated.
- few examples contain additional information in command prompt
unnecessarily and inconsistently.
This commit fixes them to enhance readability of the document.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tom Zanussi <tzanussi@gmail.com>
Fixes: cff68e582237 ("perf/scripts: Add perf-trace-python Documentation")
Link: http://lkml.kernel.org/r/20170530111827.21732-4-sj38.park@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Default function signature of trace_unhandled() got changed to include a
field dict, but its documentation, perf-script-python.txt has not been
updated. Fix it.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Pierre Tardy <tardyp@gmail.com>
Fixes: c02514850d67 ("perf scripts python: Give field dict to unhandled callback")
Link: http://lkml.kernel.org/r/20170530111827.21732-6-sj38.park@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
This commit fixes wrong code snippets for trace_begin() and trace_end()
function example definition.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tom Zanussi <tzanussi@gmail.com>
Fixes: cff68e582237 ("perf/scripts: Add perf-trace-python Documentation")
Link: http://lkml.kernel.org/r/20170530111827.21732-5-sj38.park@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
This commit fixes two errors in documents for perf-script-python and
perf-script-perl as below:
- /sys/kernel/debug/tracing events -> /sys/kernel/debug/tracing/events/
- trace_handled -> trace_unhandled
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tom Zanussi <tzanussi@gmail.com>
Fixes: cff68e582237 ("perf/scripts: Add perf-trace-python Documentation")
Link: http://lkml.kernel.org/r/20170530111827.21732-3-sj38.park@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Script generated by the '--gen-script' option contains an outdated
comment. It mentions a 'perf-trace-python' document while it has been
renamed to 'perf-script-python'. Fix it.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Fixes: 133dc4c39c57 ("perf: Rename 'perf trace' to 'perf script'")
Link: http://lkml.kernel.org/r/20170530111827.21732-2-sj38.park@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
An example in perf-probe documentation for pattern of function name
based probe addition is not providing example command for that case.
This commit fixes the example to give appropriate example command.
Signed-off-by: SeongJae Park <sj38.park@gmail.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Taeung Song <treeze.taeung@gmail.com>
Fixes: ee391de876ae ("perf probe: Update perf probe document")
Link: http://lkml.kernel.org/r/20170507103642.30560-1-sj38.park@gmail.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Linus pointed out that there is a much more efficient way of avoiding
the problem that we were trying to address in commit 9dfa7bba35ac0:
"fix race in drivers/char/random.c:get_reg()".
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
|
