| Age | Commit message (Collapse) | Author |
|---|
|
Move the USB link power configuration logic from lan78xx_link_reset()
to a new helper function lan78xx_configure_usb(). This simplifies the
main link reset path and isolates USB-specific logic.
The new function handles U1/U2 enablement based on Ethernet link speed,
but only for SuperSpeed-capable devices (LAN7800 and LAN7801). LAN7850,
a High-Speed-only device, is explicitly excluded. A warning is logged
if SuperSpeed is reported unexpectedly for LAN7850.
Add a forward declaration for lan78xx_configure_usb() as preparation for
the upcoming phylink conversion, where it will also be used from the
mac_link_up() callback.
Open questions remain:
- Why is the 1000 Mbps configuration split into two steps (U2 disable,
then U1 enable), unlike the single-step config used for 10/100 Mbps?
- U1/U2 behavior appears to depend on proper EEPROM configuration.
There are known devices in the field without EEPROM. Should the driver
enforce safe defaults in such cases?
Due to lack of USB subsystem expertise, no changes were made to this logic
beyond structural refactoring.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move the PHY interrupt acknowledgment logic from lan78xx_link_reset()
to a new helper function lan78xx_phy_int_ack(). This simplifies the
code and prepares for reusing the acknowledgment logic independently
from the full link reset process, such as when using phylink.
No functional change intended.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extract the LED enable logic based on the "microchip,led-modes"
property into a new helper function lan78xx_configure_leds_from_dt().
This simplifies lan78xx_phy_init() and improves modularity.
No functional changes intended.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Split out PHY detection into lan78xx_get_phy() and MAC-side setup into
lan78xx_mac_prepare_for_phy(), making the main lan78xx_phy_init() cleaner
and easier to follow.
This improves separation of concerns and prepares the code for a future
transition to phylink. Fixed PHY registration and interface selection
are now handled in lan78xx_get_phy(), while MAC-side delay configuration
is done in lan78xx_mac_prepare_for_phy().
The fixed PHY fallback is preserved for setups like EVB-KSZ9897-1,
where LAN7801 connects directly to a KSZ switch without a standard PHY
or device tree support.
No functional changes intended.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RGMII timing correctness relies on the PHY providing internal delays.
This is typically ensured via PHY driver, strap pins, or PCB layout.
Explicitly checking for a PHY driver here is unnecessary and non-standard.
This logic applies to all MACs, not just LAN78xx, and should be left to
phylib, phylink, or platform configuration.
Drop the check and rely on standard subsystem behavior.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ensure that return values from `lan78xx_write_reg()`,
`lan78xx_read_reg()`, and `phy_find_first()` are properly checked and
propagated. Use `ERR_PTR(ret)` for error reporting in
`lan7801_phy_init()` and replace `-EIO` with `-ENODEV` where appropriate
to provide more accurate error codes.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Thangaraj Samynathan <thangaraj.s@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With commit bcb5d6c76903 ("s390/pci: introduce lock to synchronize state
of zpci_dev's") the code to ignore power off of a PF that has child VFs
was changed from a direct return to a goto to the unlock and
pci_dev_put() section. The change however left the existing pci_dev_put()
untouched resulting in a doubple put. This can subsequently cause a use
after free if the struct pci_dev is released in an unexpected state.
Fix this by removing the extra pci_dev_put().
Cc: stable@vger.kernel.org
Fixes: bcb5d6c76903 ("s390/pci: introduce lock to synchronize state of zpci_dev's")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The zpci_create_device() function returns an error pointer that needs to
be checked before dereferencing it as a struct zpci_dev pointer. Add the
missing check in __clp_add() where it was missed when adding the
scan_list in the fixed commit. Simply not adding the device to the scan
list results in the previous behavior.
Cc: stable@vger.kernel.org
Fixes: 0467cdde8c43 ("s390/pci: Sort PCI functions prior to creating virtual busses")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
UDF maintains total length of all extents in i_lenExtents. Generally we
keep extent lengths (and thus i_lenExtents) block aligned because it
makes the file appending logic simpler. However the standard mandates
that the inode size must match the length of all extents and thus we
trim the last extent when closing the file. To catch possible bugs we
also verify that i_lenExtents matches i_size when evicting inode from
memory. Commit b405c1e58b73 ("udf: refactor udf_next_aext() to handle
error") however broke the code updating i_lenExtents and thus
udf_evict_inode() ended up spewing lots of errors about incorrectly
sized extents although the extents were actually sized properly. Fix the
updating of i_lenExtents to silence the errors.
Fixes: b405c1e58b73 ("udf: refactor udf_next_aext() to handle error")
CC: stable@vger.kernel.org
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
I found this simple bug while preparing some patches for pKVM.
AFAICT, it should be harmless (besides crashing the kernel if it
was misbehaving)
Fixes: e94a7dea2972 ("KVM: arm64: Move host page ownership tracking to the hyp vmemmap")
Signed-off-by: Mostafa Saleh <smostafa@google.com>
Link: https://lore.kernel.org/r/20250501162450.2784043-1-smostafa@google.com
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
HCRX_HOST_FLAGS, like most of these hardcoded setups, are not
a good match for options that can be selectively enabled or
disabled.
Nothing but the early setup is relying on it now, so kill the
macro and move the bag of bits where they belong.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20250430105916.3815157-3-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
Rather than restoring HCRX_EL2 to a fixed value on vcpu exit,
perform a full save/restore of the register, ensuring that
we don't lose bits that would have been set at some point in
the host kernel lifetime, such as the GCSEn bit.
Fixes: ff5181d8a2a82 ("arm64/gcs: Provide basic EL2 setup to allow GCS usage at EL0 and EL1")
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20250430105916.3815157-2-maz@kernel.org
Signed-off-by: Oliver Upton <oliver.upton@linux.dev>
|
|
The original nvme subsystem design didn't have a CONNECTING state; the
state machine allowed transitions from RESETTING to LIVE directly.
With the introduction of nvme fabrics the CONNECTING state was
introduce. Over time the nvme-pci started to use the CONNECTING state as
well.
Eventually, a bug fix for the nvme-fc started to depend that the only
valid transition to LIVE was from CONNECTING. Though this change didn't
update the firmware update handler which was still depending on
RESETTING to LIVE transition.
The simplest way to address it for the time being is to switch into
CONNECTING state before going to LIVE state.
Fixes: d2fe192348f9 ("nvme: only allow entering LIVE from CONNECTING state")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Daniel Wagner <wagi@kernel.org>
Closes: https://lore.kernel.org/all/0134ea15-8d5f-41f7-9e9a-d7e6d82accaa@roeck-us.net
Reviewed-by: Keith Busch <kbusch@kernel.org>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes Berg says:
====================
Couple of fixes:
* iwlwifi: add two missing device entries
* cfg80211: fix a potential out-of-bounds access
* mac80211: fix format of TID to link mapping action frames
* tag 'wireless-2025-05-06' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless:
wifi: iwlwifi: add support for Killer on MTL
wifi: mac80211: fix the type of status_code for negotiated TID to Link Mapping
wifi: cfg80211: fix out-of-bounds access during multi-link element defragmentation
====================
Link: https://patch.msgid.link/20250506203506.158818-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Johannes Berg says:
====================
wireless features, notably
* stack
- free SKBTX_WIFI_STATUS flag
- fixes for VLAN multicast in multi-link
- improve codel parameters (revert some old twiddling)
* ath12k
- Enable AHB support for IPQ5332.
- Add monitor interface support to QCN9274.
- Add MLO support to WCN7850.
- Add 802.11d scan offload support to WCN7850.
* ath11k
- Restore hibernation support
* iwlwifi
- EMLSR on two 5 GHz links
* mwifiex
- cleanups/refactoring
along with many other small features/cleanups
* tag 'wireless-next-2025-05-06' of https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (177 commits)
Revert "wifi: iwlwifi: clean up config macro"
wifi: iwlwifi: move phy_filters to fw_runtime
wifi: iwlwifi: pcie: make sure to lock rxq->read
wifi: iwlwifi: add definitions for iwl_mac_power_cmd version 2
wifi: iwlwifi: clean up config macro
wifi: iwlwifi: mld: simplify iwl_mld_rx_fill_status()
wifi: iwlwifi: mld: rx: simplify channel handling
wifi: iwlwifi: clean up band in RX metadata
wifi: iwlwifi: mld: skip unknown FW channel load values
wifi: iwlwifi: define API for external FSEQ images
wifi: iwlwifi: mld: allow EMLSR on separated 5 GHz subbands
wifi: iwlwifi: mld: use cfg80211_chandef_get_width()
wifi: iwlwifi: mld: fix iwl_mld_emlsr_disallowed_with_link() return
wifi: iwlwifi: mld: clarify variable type
wifi: iwlwifi: pcie: add support for the reset handshake in MSI
wifi: mac80211_hwsim: Prevent tsf from setting if beacon is disabled
wifi: mac80211: restructure tx profile retrieval for MLO MBSSID
wifi: nl80211: add link id of transmitted profile for MLO MBSSID
wifi: ieee80211: Add helpers to fetch EMLSR delay and timeout values
wifi: mac80211: update ML STA with EML capabilities
...
====================
Link: https://patch.msgid.link/20250506174656.119970-3-johannes@sipsolutions.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2025-05-06
The first patch is by Antonios Salios and adds a missing
spin_lock_init() to the m_can driver.
The next 3 patches are by me and fix the unregistration order in the
mcp251xfd, rockchip_canfd and m_can driver.
The last patch is by Oliver Hartkopp and fixes RCU and BH
locking/handling in the CAN gw protocol.
* tag 'linux-can-fixes-for-6.15-20250506' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can:
can: gw: fix RCU/BH usage in cgw_create_job()
can: mcan: m_can_class_unregister(): fix order of unregistration calls
can: rockchip_canfd: rkcanfd_remove(): fix order of unregistration calls
can: mcp251xfd: mcp251xfd_remove(): fix order of unregistration calls
can: mcp251xfd: fix TDC setting for low data bit rates
can: m_can: m_can_class_allocate_dev(): initialize spin lock on device probe
====================
Link: https://patch.msgid.link/20250506135939.652543-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Accidentally spotted while trying to understand what else needs
to be renamed to netif_ prefix. Most of the calls to dev_set_promiscuity
are adjacent to dev_set_allmulti or dev_disable_lro so it should
be safe to add the lock. Note that new netif_set_promiscuity is
currently unused, the locked paths call __dev_set_promiscuity directly.
Fixes: ad7c7b2172c3 ("net: hold netdev instance lock during sysfs operations")
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250506011919.2882313-1-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When compressed data deduplication is enabled, multiple logical extents
may reference the same compressed physical cluster.
The previous commit 94c43de73521 ("erofs: fix wrong primary bvec
selection on deduplicated extents") already avoids using shortened
bvecs. However, in such cases, the extra temporary buffers also
need to be preserved for later use in z_erofs_fill_other_copies() to
to prevent data corruption.
IOWs, extra temporary buffers have to be retained not only due to
varying start relative offsets (`pageofs_out`, as indicated by
`pcl->multibases`) but also because of shortened bvecs.
android.hardware.graphics.composer@2.1.so : 270696 bytes
0: 0.. 204185 | 204185 : 628019200.. 628084736 | 65536
-> 1: 204185.. 225536 | 21351 : 544063488.. 544129024 | 65536
2: 225536.. 270696 | 45160 : 0.. 0 | 0
com.android.vndk.v28.apex : 93814897 bytes
...
364: 53869896..54095257 | 225361 : 543997952.. 544063488 | 65536
-> 365: 54095257..54309344 | 214087 : 544063488.. 544129024 | 65536
366: 54309344..54514557 | 205213 : 544129024.. 544194560 | 65536
...
Both 204185 and 54095257 have the same start relative offset of 3481,
but the logical page 55 of `android.hardware.graphics.composer@2.1.so`
ranges from 225280 to 229632, forming a shortened bvec [225280, 225536)
that cannot be used for decompressing the range from 54095257 to
54309344 of `com.android.vndk.v28.apex`.
Since `pcl->multibases` is already meaningless, just mark `be->keepxcpy`
on demand for simplicity.
Again, this issue can only lead to data corruption if `-Ededupe` is on.
Fixes: 94c43de73521 ("erofs: fix wrong primary bvec selection on deduplicated extents")
Reviewed-by: Hongbo Li <lihongbo22@huawei.com>
Signed-off-by: Gao Xiang <hsiangkao@linux.alibaba.com>
Link: https://lore.kernel.org/r/20250506101850.191506-1-hsiangkao@linux.alibaba.com
|
|
__qdisc_destroy() calls into various qdiscs .destroy() op, which in turn
can call .ndo_setup_tc(), which requires the netdev instance lock.
This commit extends the critical section in
unregister_netdevice_many_notify() to cover dev_shutdown() (and
dev_tcx_uninstall() as a side-effect) and acquires the netdev instance
lock in __dev_change_net_namespace() for the other dev_shutdown() call.
This should now guarantee that for all qdisc ops, the netdev instance
lock is held during .ndo_setup_tc().
Fixes: a0527ee2df3f ("net: hold netdev instance lock during qdisc ndo_setup_tc")
Signed-off-by: Cosmin Ratiu <cratiu@nvidia.com>
Acked-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250505194713.1723399-1-cratiu@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use Device Serial Number instead of PCI bus/device/function for
the index of struct ice_adapter.
Functions on the same physical device should point to the very same
ice_adapter instance, but with two PFs, when at least one of them is
PCI-e passed-through to a VM, it is no longer the case - PFs will get
seemingly random PCI BDF values, and thus indices, what finally leds to
each of them being on their own instance of ice_adapter. That causes them
to don't attempt any synchronization of the PTP HW clock usage, or any
other future resources.
DSN works nicely in place of the index, as it is "immutable" in terms of
virtualization.
Fixes: 0e2bddf9e5f9 ("ice: add ice_adapter for shared data across PFs on the same NIC")
Suggested-by: Jacob Keller <jacob.e.keller@intel.com>
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Suggested-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Signed-off-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250505161939.2083581-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Jiri Pirko says:
====================
devlink: sanitize variable typed attributes
This is continuation based on first two patches of
https://lore.kernel.org/20250425214808.507732-1-saeed@kernel.org
Better to take it as a separate patchset, as the rest of the original
patchset is probably settled.
This patchset is taking care of incorrect usage of internal NLA_* values
in uapi, introduces new enum (in patch #2) that shadows NLA_* values and
makes that part of UAPI.
The last two patches removes unnecessary translations with maintaining
clear devlink param driver api.
====================
Link: https://patch.msgid.link/20250505114513.53370-1-jiri@resnulli.us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Use newly introduced DEVLINK_VAR_ATTR_TYPE_* enum values instead of
internal NLA_* in fmsg health reporter code.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250505114513.53370-5-jiri@resnulli.us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Assign DEVLINK_PARAM_TYPE_* enum values to DEVLINK_VAR_ATTR_TYPE_* to
ensure the same values are used internally and in UAPI. Benefit from
that by removing the value translations.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250505114513.53370-4-jiri@resnulli.us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Devlink param and health reporter fmsg use attributes with dynamic type
which is determined according to a different type. Currently used values
are NLA_*. The problem is, they are not part of UAPI. They may change
which would cause a break.
To make this future safe, introduce a enum that shadows NLA_* values in
it and is part of UAPI.
Also, this allows to possibly carry types that are unrelated to NLA_*
values.
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250505114513.53370-3-jiri@resnulli.us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
in case the enum has holes, instead of hard stop, generate a validation
callback to check valid enum values.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Link: https://patch.msgid.link/20250505114513.53370-2-jiri@resnulli.us
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fix ethtool syntax for setting ntuple rule into rss. It should be
`context' instead of `action'.
Signed-off-by: David Wei <dw@davidwei.uk>
Link: https://patch.msgid.link/20250503043007.857215-1-dw@davidwei.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Calling core::fmt::write() from rust code while FineIBT is enabled
results in a kernel panic:
[ 4614.199779] kernel BUG at arch/x86/kernel/cet.c:132!
[ 4614.205343] Oops: invalid opcode: 0000 [#1] PREEMPT SMP NOPTI
[ 4614.211781] CPU: 2 UID: 0 PID: 6057 Comm: dmabuf_dump Tainted: G U O 6.12.17-android16-0-g6ab38c534a43 #1 9da040f27673ec3945e23b998a0f8bd64c846599
[ 4614.227832] Tainted: [U]=USER, [O]=OOT_MODULE
[ 4614.241247] RIP: 0010:do_kernel_cp_fault+0xea/0xf0
...
[ 4614.398144] RIP: 0010:_RNvXs5_NtNtNtCs3o2tGsuHyou_4core3fmt3num3impyNtB9_7Display3fmt+0x0/0x20
[ 4614.407792] Code: 48 f7 df 48 0f 48 f9 48 89 f2 89 c6 5d e9 18 fd ff ff 0f 1f 84 00 00 00 00 00 f3 0f 1e fa 41 81 ea 14 61 af 2c 74 03 0f 0b 90 <66> 0f 1f 00 55 48 89 e5 48 89 f2 48 8b 3f be 01 00 00 00 5d e9 e7
[ 4614.428775] RSP: 0018:ffffb95acfa4ba68 EFLAGS: 00010246
[ 4614.434609] RAX: 0000000000000000 RBX: 0000000000000010 RCX: 0000000000000000
[ 4614.442587] RDX: 0000000000000007 RSI: ffffb95acfa4ba70 RDI: ffffb95acfa4bc88
[ 4614.450557] RBP: ffffb95acfa4bae0 R08: ffff0a00ffffff05 R09: 0000000000000070
[ 4614.458527] R10: 0000000000000000 R11: ffffffffab67eaf0 R12: ffffb95acfa4bcc8
[ 4614.466493] R13: ffffffffac5d50f0 R14: 0000000000000000 R15: 0000000000000000
[ 4614.474473] ? __cfi__RNvXs5_NtNtNtCs3o2tGsuHyou_4core3fmt3num3impyNtB9_7Display3fmt+0x10/0x10
[ 4614.484118] ? _RNvNtCs3o2tGsuHyou_4core3fmt5write+0x1d2/0x250
This happens because core::fmt::write() calls
core::fmt::rt::Argument::fmt(), which currently has CFI disabled:
library/core/src/fmt/rt.rs:
171 // FIXME: Transmuting formatter in new and indirectly branching to/calling
172 // it here is an explicit CFI violation.
173 #[allow(inline_no_sanitize)]
174 #[no_sanitize(cfi, kcfi)]
175 #[inline]
176 pub(super) unsafe fn fmt(&self, f: &mut Formatter<'_>) -> Result {
This causes a Control Protection exception, because FineIBT has sealed
off the original function's endbr64.
This makes rust currently incompatible with FineIBT. Add a Kconfig
dependency that prevents FineIBT from getting turned on by default
if rust is enabled.
[ Rust 1.88.0 (scheduled for 2025-06-26) should have this fixed [1],
and thus we relaxed the condition with Rust >= 1.88.
When `objtool` lands checking for this with e.g. [2], the plan is
to ideally run that in upstream Rust's CI to prevent regressions
early [3], since we do not control `core`'s source code.
Alice tested the Rust PR backported to an older compiler.
Peter would like that Rust provides a stable `core` which can be
pulled into the kernel: "Relying on that much out of tree code is
'unfortunate'".
- Miguel ]
Signed-off-by: Paweł Anikiel <panikiel@google.com>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Link: https://github.com/rust-lang/rust/pull/139632 [1]
Link: https://lore.kernel.org/rust-for-linux/20250410154556.GB9003@noisy.programming.kicks-ass.net/ [2]
Link: https://github.com/rust-lang/rust/pull/139632#issuecomment-2801950873 [3]
Link: https://lore.kernel.org/r/20250410115420.366349-1-panikiel@google.com
Link: https://lore.kernel.org/r/att0-CANiq72kjDM0cKALVy4POEzhfdT4nO7tqz0Pm7xM+3=_0+L1t=A@mail.gmail.com
[ Reduced splat. - Miguel ]
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
|
|
Starting with Rust 1.88.0 (expected 2025-06-26) [1], `rustc` may move
back the `uninlined_format_args` to `style` from `pedantic` (it was
there waiting for rust-analyzer suppotr), and thus we will start to see
lints like:
warning: variables can be used directly in the `format!` string
--> rust/macros/kunit.rs:105:37
|
105 | let kunit_wrapper_fn_name = format!("kunit_rust_wrapper_{}", test);
| ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
= help: for further information visit https://rust-lang.github.io/rust-clippy/master/index.html#uninlined_format_args
help: change this to
|
105 - let kunit_wrapper_fn_name = format!("kunit_rust_wrapper_{}", test);
105 + let kunit_wrapper_fn_name = format!("kunit_rust_wrapper_{test}");
There is even a case that is a pure removal:
warning: variables can be used directly in the `format!` string
--> rust/macros/module.rs:51:13
|
51 | format!("{field}={content}\0", field = field, content = content)
| ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
|
= help: for further information visit https://rust-lang.github.io/rust-clippy/master/index.html#uninlined_format_args
help: change this to
|
51 - format!("{field}={content}\0", field = field, content = content)
51 + format!("{field}={content}\0")
The lints all seem like nice cleanups, thus just apply them.
We may want to disable `allow-mixed-uninlined-format-args` in the future.
Cc: stable@vger.kernel.org # Needed in 6.12.y and later (Rust is pinned in older LTSs).
Link: https://github.com/rust-lang/rust-clippy/pull/14160 [1]
Acked-by: Benno Lossin <lossin@kernel.org>
Reviewed-by: Tamir Duberstein <tamird@gmail.com>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Link: https://lore.kernel.org/r/20250502140237.1659624-6-ojeda@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
|
|
configuration
Starting with Rust 1.88.0 (expected 2025-06-26) [1], Clippy may start
warning about paths that do not resolve in the `disallowed_macros`
configuration:
warning: `kernel::dbg` does not refer to an existing macro
--> .clippy.toml:10:5
|
10 | { path = "kernel::dbg", reason = "the `dbg!` macro is intended as a debugging tool" },
| ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
This is a lint we requested at [2], due to the trouble debugging
the lint due to false negatives (e.g. [3]), which we use to emulate
`clippy::dbg_macro` [4]. See commit 8577c9dca799 ("rust: replace
`clippy::dbg_macro` with `disallowed_macros`") for more details.
Given the false negatives are not resolved yet, it is expected that
Clippy complains about not finding this macro.
Thus, until the false negatives are fixed (and, even then, probably we
will need to wait for the MSRV to raise enough), use the escape hatch
to allow an invalid path.
Cc: stable@vger.kernel.org # Needed in 6.12.y and later (Rust is pinned in older LTSs).
Link: https://github.com/rust-lang/rust-clippy/pull/14397 [1]
Link: https://github.com/rust-lang/rust-clippy/issues/11432 [2]
Link: https://github.com/rust-lang/rust-clippy/issues/11431 [3]
Link: https://github.com/rust-lang/rust-clippy/issues/11303 [4]
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Link: https://lore.kernel.org/r/20250502140237.1659624-5-ojeda@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
|
|
Starting with Rust 1.88.0 (expected 2025-06-26) [1][2], `rustc` may
introduce a new lint that catches unnecessary transmutes, e.g.:
error: unnecessary transmute
--> rust/uapi/uapi_generated.rs:23242:18
|
23242 | unsafe { ::core::mem::transmute(self._bitfield_1.get(0usize, 1u8) as u8) }
| ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ help: replace this with: `(self._bitfield_1.get(0usize, 1u8) as u8 == 1)`
|
= note: `-D unnecessary-transmutes` implied by `-D warnings`
= help: to override `-D warnings` add `#[allow(unnecessary_transmutes)]`
There are a lot of them (at least 300), but luckily they are all in
`bindgen`-generated code.
Thus clean all up by allowing it there.
Since unknown lints trigger a lint itself in older compilers, do it
conditionally so that we can keep the `unknown_lints` lint enabled.
Cc: stable@vger.kernel.org # Needed in 6.12.y and later (Rust is pinned in older LTSs).
Link: https://github.com/rust-lang/rust/pull/136083 [1]
Link: https://github.com/rust-lang/rust/issues/136067 [2]
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Link: https://lore.kernel.org/r/20250502140237.1659624-4-ojeda@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
|
|
Starting with Rust 1.87.0 (expected 2025-05-15) [1], Clippy may expand
the `ptr_eq` lint, e.g.:
error: use `core::ptr::eq` when comparing raw pointers
--> rust/kernel/list.rs:438:12
|
438 | if self.first == item {
| ^^^^^^^^^^^^^^^^^^ help: try: `core::ptr::eq(self.first, item)`
|
= help: for further information visit https://rust-lang.github.io/rust-clippy/master/index.html#ptr_eq
= note: `-D clippy::ptr-eq` implied by `-D warnings`
= help: to override `-D warnings` add `#[allow(clippy::ptr_eq)]`
It is expected that a PR to relax the lint will be backported [2] by
the time Rust 1.87.0 releases, since the lint was considered too eager
(at least by default) [3].
Thus allow the lint temporarily just in case.
Cc: stable@vger.kernel.org # Needed in 6.12.y and later (Rust is pinned in older LTSs).
Link: https://github.com/rust-lang/rust-clippy/pull/14339 [1]
Link: https://github.com/rust-lang/rust-clippy/pull/14526 [2]
Link: https://github.com/rust-lang/rust-clippy/issues/14525 [3]
Link: https://lore.kernel.org/r/20250502140237.1659624-3-ojeda@kernel.org
[ Converted to `allow`s since backport was confirmed. - Miguel ]
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
|
|
Starting with Rust 1.87.0 (expected 2025-05-15), `objtool` may report:
rust/core.o: warning: objtool: _R..._4core9panicking9panic_fmt() falls
through to next function _R..._4core9panicking18panic_nounwind_fmt()
rust/core.o: warning: objtool: _R..._4core9panicking18panic_nounwind_fmt()
falls through to next function _R..._4core9panicking5panic()
The reason is that `rust_begin_unwind` is now mangled:
_R..._7___rustc17rust_begin_unwind
Thus add the mangled one to the list so that `objtool` knows it is
actually `noreturn`.
See commit 56d680dd23c3 ("objtool/rust: list `noreturn` Rust functions")
for more details.
Alternatively, we could remove the fixed one in `noreturn.h` and relax
this test to cover both, but it seems best to be strict as long as we can.
Cc: stable@vger.kernel.org # Needed in 6.12.y and later (Rust is pinned in older LTSs).
Cc: Josh Poimboeuf <jpoimboe@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Reviewed-by: Alice Ryhl <aliceryhl@google.com>
Link: https://lore.kernel.org/r/20250502140237.1659624-2-ojeda@kernel.org
Signed-off-by: Miguel Ojeda <ojeda@kernel.org>
|
|
For now, we need another entry for these devices, this
will be changed completely for 6.16.
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219926
Link: https://patch.msgid.link/20250506214258.2efbdc9e9a82.I31915ec252bd1c74bd53b89a0e214e42a74b6f2e@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The status code should be type of __le16.
Fixes: 83e897a961b8 ("wifi: ieee80211: add definitions for negotiated TID to Link map")
Fixes: 8f500fbc6c65 ("wifi: mac80211: process and save negotiated TID to Link mapping request")
Signed-off-by: Michael-CY Lee <michael-cy.lee@mediatek.com>
Link: https://patch.msgid.link/20250505081946.3927214-1-michael-cy.lee@mediatek.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
defragmentation
Currently during the multi-link element defragmentation process, the
multi-link element length added to the total IEs length when calculating
the length of remaining IEs after the multi-link element in
cfg80211_defrag_mle(). This could lead to out-of-bounds access if the
multi-link element or its corresponding fragment elements are the last
elements in the IEs buffer.
To address this issue, correctly calculate the remaining IEs length by
deducting the multi-link element end offset from total IEs end offset.
Cc: stable@vger.kernel.org
Fixes: 2481b5da9c6b ("wifi: cfg80211: handle BSS data contained in ML probe responses")
Signed-off-by: Veerendranath Jakkam <quic_vjakkam@quicinc.com>
Link: https://patch.msgid.link/20250424-fix_mle_defragmentation_oob_access-v1-1-84412a1743fa@quicinc.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The vfio-pci huge_fault handler doesn't make any attempt to insert a
mapping containing the faulting address, it only inserts mappings if the
faulting address and resulting pfn are aligned. This works in a lot of
cases, particularly in conjunction with QEMU where DMA mappings linearly
fault the mmap. However, there are configurations where we don't get
that linear faulting and pages are faulted on-demand.
The scenario reported in the bug below is such a case, where the physical
address width of the CPU is greater than that of the IOMMU, resulting in a
VM where guest firmware has mapped device MMIO beyond the address width of
the IOMMU. In this configuration, the MMIO is faulted on demand and
tracing indicates that occasionally the faults generate a VM_FAULT_OOM.
Given the use case, this results in a "error: kvm run failed Bad address",
killing the VM.
The host is not under memory pressure in this test, therefore it's
suspected that VM_FAULT_OOM is actually the result of a NULL return from
__pte_offset_map_lock() in the get_locked_pte() path from insert_pfn().
This suggests a potential race inserting a pte concurrent to a pmd, and
maybe indicates some deficiency in the mm layer properly handling such a
case.
Nevertheless, Peter noted the inconsistency of vfio-pci's huge_fault
handler where our mapping granularity depends on the alignment of the
faulting address relative to the order rather than aligning the faulting
address to the order to more consistently insert huge mappings. This
change not only uses the page tables more consistently and efficiently, but
as any fault to an aligned page results in the same mapping, the race
condition suspected in the VM_FAULT_OOM is avoided.
Reported-by: Adolfo <adolfotregosa@gmail.com>
Closes: https://bugzilla.kernel.org/show_bug.cgi?id=220057
Fixes: 09dfc8a5f2ce ("vfio/pci: Fallback huge faults for unaligned pfn")
Cc: stable@vger.kernel.org
Tested-by: Adolfo <adolfotregosa@gmail.com>
Co-developed-by: Peter Xu <peterx@redhat.com>
Signed-off-by: Peter Xu <peterx@redhat.com>
Link: https://lore.kernel.org/r/20250502224035.3183451-1-alex.williamson@redhat.com
Signed-off-by: Alex Williamson <alex.williamson@redhat.com>
|
|
set_high_memory() touches arch_zone_lowest_possible_pfn which is
marked as __initdata, which creates a section mismatch.
Since the only user of the function is free_area_init() which is also marked
as __init, mark set_high_memory() as __init as well.
Signed-off-by: Oscar Salvador <osalvador@suse.de>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202505060901.Qcs06UoB-lkp@intel.com/
Link: https://lore.kernel.org/r/20250506111012.108743-1-osalvador@suse.de
Signed-off-by: Mike Rapoport (Microsoft) <rppt@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux
Pull btrfs fixes from David Sterba:
- revert device path canonicalization, this does not work as intended
with namespaces and is not reliable in all setups
- fix crash in scrub when checksum tree is not valid, e.g. when mounted
with rescue=ignoredatacsums
- fix crash when tracepoint btrfs_prelim_ref_insert is enabled
- other minor fixups:
- open code folio_index(), meant to be used in MM code
- use matching type for sizeof in compression allocation
* tag 'for-6.15-rc5-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux:
btrfs: open code folio_index() in btree_clear_folio_dirty_tag()
Revert "btrfs: canonicalize the device path before adding it"
btrfs: avoid NULL pointer dereference if no valid csum tree
btrfs: handle empty eb->folios in num_extent_folios()
btrfs: correct the order of prelim_ref arguments in btrfs__prelim_ref
btrfs: compression: adjust cb->compressed_folios allocation type
|
|
With the possibility of intra-mode BHI via cBPF, complete mitigation for
BHI is to use IBHF (history fence) instruction with BHI_DIS_S set. Since
this new instruction is only available in 64-bit mode, setting BHI_DIS_S in
32-bit mode is only a partial mitigation.
Do not set BHI_DIS_S in 32-bit mode so as to avoid reporting misleading
mitigated status. With this change IBHF won't be used in 32-bit mode, also
remove the CONFIG_X86_64 check from emit_spectre_bhb_barrier().
Suggested-by: Josh Poimboeuf <jpoimboe@kernel.org>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Reviewed-by: Josh Poimboeuf <jpoimboe@kernel.org>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
|
|
Classic BPF programs can be run by unprivileged users, allowing
unprivileged code to execute inside the kernel. Attackers can use this to
craft branch history in kernel mode that can influence the target of
indirect branches.
BHI_DIS_S provides user-kernel isolation of branch history, but cBPF can be
used to bypass this protection by crafting branch history in kernel mode.
To stop intra-mode attacks via cBPF programs, Intel created a new
instruction Indirect Branch History Fence (IBHF). IBHF prevents the
predicted targets of subsequent indirect branches from being influenced by
branch history prior to the IBHF. IBHF is only effective while BHI_DIS_S is
enabled.
Add the IBHF instruction to cBPF jitted code's exit path. Add the new fence
when the hardware mitigation is enabled (i.e., X86_FEATURE_CLEAR_BHB_HW is
set) or after the software sequence (X86_FEATURE_CLEAR_BHB_LOOP) is being
used in a virtual machine. Note that X86_FEATURE_CLEAR_BHB_HW and
X86_FEATURE_CLEAR_BHB_LOOP are mutually exclusive, so the JIT compiler will
only emit the new fence, not the SW sequence, when X86_FEATURE_CLEAR_BHB_HW
is set.
Hardware that enumerates BHI_NO basically has BHI_DIS_S protections always
enabled, regardless of the value of BHI_DIS_S. Since BHI_DIS_S doesn't
protect against intra-mode attacks, enumerate BHI bug on BHI_NO hardware as
well.
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
|
|
Classic BPF programs have been identified as potential vectors for
intra-mode Branch Target Injection (BTI) attacks. Classic BPF programs can
be run by unprivileged users. They allow unprivileged code to execute
inside the kernel. Attackers can use unprivileged cBPF to craft branch
history in kernel mode that can influence the target of indirect branches.
Introduce a branch history buffer (BHB) clearing sequence during the JIT
compilation of classic BPF programs. The clearing sequence is the same as
is used in previous mitigations to protect syscalls. Since eBPF programs
already have their own mitigations in place, only insert the call on
classic programs that aren't run by privileged users.
Signed-off-by: Daniel Sneddon <daniel.sneddon@linux.intel.com>
Signed-off-by: Pawan Gupta <pawan.kumar.gupta@linux.intel.com>
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Alexandre Chartre <alexandre.chartre@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mikulas Patocka:
- fix reading past the end of allocated memory
- fix missing dm_put_live_table() in dm_keyslot_evict()
* tag 'for-6.15/dm-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix copying after src array boundaries
dm: add missing unlock on in dm_keyslot_evict()
|
|
Coverity noticed that the rc on smb2_parse_contexts() was not being checked
in the case of compounded operations. Since we don't want to stop parsing
the following compounded responses which are likely valid, we can't easily
error out here, but at least print a warning message if server has a bug
causing us to skip parsing the open response contexts.
Addresses-Coverity: 1639191
Acked-by: Paulo Alcantara (Red Hat) <pc@manguebit.com>
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
As reported by Sebastian Andrzej Siewior the use of local_bh_disable()
is only feasible in uni processor systems to update the modification rules.
The usual use-case to update the modification rules is to update the data
of the modifications but not the modification types (AND/OR/XOR/SET) or
the checksum functions itself.
To omit additional memory allocations to maintain fast modification
switching times, the modification description space is doubled at gw-job
creation time so that only the reference to the active modification
description is changed under rcu protection.
Rename cgw_job::mod to cf_mod and make it a RCU pointer. Allocate in
cgw_create_job() and free it together with cgw_job in
cgw_job_free_rcu(). Update all users to dereference cgw_job::cf_mod with
a RCU accessor and if possible once.
[bigeasy: Replace mod1/mod2 from the Oliver's original patch with dynamic
allocation, use RCU annotation and accessor]
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Closes: https://lore.kernel.org/linux-can/20231031112349.y0aLoBrz@linutronix.de/
Fixes: dd895d7f21b2 ("can: cangw: introduce optional uid to reference created routing jobs")
Tested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Link: https://patch.msgid.link/20250429070555.cs-7b_eZ@linutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Marc Kleine-Budde <mkl@pengutronix.de> says:
If a driver is removed, the driver framework invokes the driver's
remove callback. A CAN driver's remove function calls
unregister_candev(), which calls net_device_ops::ndo_stop further down
in the call stack for interfaces which are in the "up" state.
With the mcp251xfd driver the removal of the module causes the
following warning:
| WARNING: CPU: 0 PID: 352 at net/core/dev.c:7342 __netif_napi_del_locked+0xc8/0xd8
as can_rx_offload_del() deletes the NAPI, while it is still active,
because the interface is still up.
To fix the warning, first unregister the network interface, which
calls net_device_ops::ndo_stop, which disables the NAPI, and then call
can_rx_offload_del().
All other driver using the rx-offload helper have been checked and the
same issue has been found in the rockchip and m_can driver. These have
been fixed, but only compile time tested. On the mcp251xfd the fix was
tested on hardware.
Link: https://patch.msgid.link/20250502-can-rx-offload-del-v1-0-59a9b131589d@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If a driver is removed, the driver framework invokes the driver's
remove callback. A CAN driver's remove function calls
unregister_candev(), which calls net_device_ops::ndo_stop further down
in the call stack for interfaces which are in the "up" state.
The removal of the module causes a warning, as can_rx_offload_del()
deletes the NAPI, while it is still active, because the interface is
still up.
To fix the warning, first unregister the network interface, which
calls net_device_ops::ndo_stop, which disables the NAPI, and then call
can_rx_offload_del().
Fixes: 1be37d3b0414 ("can: m_can: fix periph RX path: use rx-offload to ensure skbs are sent from softirq context")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250502-can-rx-offload-del-v1-3-59a9b131589d@pengutronix.de
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
If a driver is removed, the driver framework invokes the driver's
remove callback. A CAN driver's remove function calls
unregister_candev(), which calls net_device_ops::ndo_stop further down
in the call stack for interfaces which are in the "up" state.
The removal of the module causes a warning, as can_rx_offload_del()
deletes the NAPI, while it is still active, because the interface is
still up.
To fix the warning, first unregister the network interface, which
calls net_device_ops::ndo_stop, which disables the NAPI, and then call
can_rx_offload_del().
Fixes: ff60bfbaf67f ("can: rockchip_canfd: add driver for Rockchip CAN-FD controller")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250502-can-rx-offload-del-v1-2-59a9b131589d@pengutronix.de
Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In case of a ZONE APPEND write, regardless of native ZONE APPEND or the
emulation layer in the zone write plugging code, the sector the data got
written to by the device needs to be updated in the bio.
At the moment, this is done for every native ZONE APPEND write and every
request that is flagged with 'BIO_ZONE_WRITE_PLUGGING'. But thus
superfluously updates the sector for regular writes to a zoned block
device.
Check if a bio is a native ZONE APPEND write or if the bio is flagged as
'BIO_EMULATES_ZONE_APPEND', meaning the block layer's zone write plugging
code handles the ZONE APPEND and translates it into a regular write and
back. Only if one of these two criterion is met, update the sector in the
bio upon completion.
Signed-off-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/dea089581cb6b777c1cd1500b38ac0b61df4b2d1.1746530748.git.jth@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If a driver is removed, the driver framework invokes the driver's
remove callback. A CAN driver's remove function calls
unregister_candev(), which calls net_device_ops::ndo_stop further down
in the call stack for interfaces which are in the "up" state.
With the mcp251xfd driver the removal of the module causes the
following warning:
| WARNING: CPU: 0 PID: 352 at net/core/dev.c:7342 __netif_napi_del_locked+0xc8/0xd8
as can_rx_offload_del() deletes the NAPI, while it is still active,
because the interface is still up.
To fix the warning, first unregister the network interface, which
calls net_device_ops::ndo_stop, which disables the NAPI, and then call
can_rx_offload_del().
Fixes: 55e5b97f003e ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Cc: stable@vger.kernel.org
Link: https://patch.msgid.link/20250502-can-rx-offload-del-v1-1-59a9b131589d@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The TDC is currently hardcoded enabled. This means that even for lower
CAN-FD data bitrates (with a DBRP (data bitrate prescaler) > 2) a TDC
is configured. This leads to a bus-off condition.
ISO 11898-1 section 11.3.3 says "Transmitter delay compensation" (TDC)
is only applicable if DBRP is 1 or 2.
To fix the problem, switch the driver to use the TDC calculation
provided by the CAN driver framework (which respects ISO 11898-1
section 11.3.3). This has the positive side effect that userspace can
control TDC as needed.
Demonstration of the feature in action:
| $ ip link set can0 up type can bitrate 125000 dbitrate 500000 fd on
| $ ip -details link show can0
| 3: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 72 qdisc pfifo_fast state UP mode DEFAULT group default qlen 10
| link/can promiscuity 0 allmulti 0 minmtu 0 maxmtu 0
| can <FD> state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
| bitrate 125000 sample-point 0.875
| tq 50 prop-seg 69 phase-seg1 70 phase-seg2 20 sjw 10 brp 2
| mcp251xfd: tseg1 2..256 tseg2 1..128 sjw 1..128 brp 1..256 brp_inc 1
| dbitrate 500000 dsample-point 0.875
| dtq 125 dprop-seg 6 dphase-seg1 7 dphase-seg2 2 dsjw 1 dbrp 5
| mcp251xfd: dtseg1 1..32 dtseg2 1..16 dsjw 1..16 dbrp 1..256 dbrp_inc 1
| tdcv 0..63 tdco 0..63
| clock 40000000 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 tso_max_size 65536 tso_max_segs 65535 gro_max_size 65536 parentbus spi parentdev spi0.0
| $ ip link set can0 up type can bitrate 1000000 dbitrate 4000000 fd on
| $ ip -details link show can0
| 3: can0: <NOARP,UP,LOWER_UP,ECHO> mtu 72 qdisc pfifo_fast state UP mode DEFAULT group default qlen 10
| link/can promiscuity 0 allmulti 0 minmtu 0 maxmtu 0
| can <FD,TDC-AUTO> state ERROR-ACTIVE (berr-counter tx 0 rx 0) restart-ms 0
| bitrate 1000000 sample-point 0.750
| tq 25 prop-seg 14 phase-seg1 15 phase-seg2 10 sjw 5 brp 1
| mcp251xfd: tseg1 2..256 tseg2 1..128 sjw 1..128 brp 1..256 brp_inc 1
| dbitrate 4000000 dsample-point 0.700
| dtq 25 dprop-seg 3 dphase-seg1 3 dphase-seg2 3 dsjw 1 dbrp 1
| tdco 7
| mcp251xfd: dtseg1 1..32 dtseg2 1..16 dsjw 1..16 dbrp 1..256 dbrp_inc 1
| tdcv 0..63 tdco 0..63
| clock 40000000 numtxqueues 1 numrxqueues 1 gso_max_size 65536 gso_max_segs 65535 tso_max_size 65536 tso_max_segs 65535 gro_max_size 65536 parentbus spi parentdev spi0.0
There has been some confusion about the MCP2518FD using a relative or
absolute TDCO due to the datasheet specifying a range of [-64,63]. I
have a custom board with a 40 MHz clock and an estimated loop delay of
100 to 216 ns. During testing at a data bit rate of 4 Mbit/s I found
that using can_get_relative_tdco() resulted in bus-off errors. The
final TDCO value was 1 which corresponds to a 10% SSP in an absolute
configuration. This behavior is expected if the TDCO value is really
absolute and not relative. Using priv->can.tdc.tdco instead results in
a final TDCO of 8, setting the SSP at exactly 80%. This configuration
works.
The automatic, manual, and off TDC modes were tested at speeds up to,
and including, 8 Mbit/s on real hardware and behave as expected.
Fixes: 55e5b97f003e ("can: mcp25xxfd: add driver for Microchip MCP25xxFD SPI CAN")
Reported-by: Kelsey Maes <kelsey@vpprocess.com>
Closes: https://lore.kernel.org/all/C2121586-C87F-4B23-A933-845362C29CA1@vpprocess.com
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Kelsey Maes <kelsey@vpprocess.com>
Link: https://patch.msgid.link/20250430161501.79370-1-kelsey@vpprocess.com
[mkl: add comment]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
