| Age | Commit message (Collapse) | Author |
|---|
|
Minor PTP register refactor, including logical grouping E825C 1-step
timestamping registers. Remove unused register definitions
(PHY_REG_GPCS_BITSLIP, PHY_REG_REVISION).
Also, apply preferred GENMASK macro (instead of ICE_M) for register
fields definition affected by this patch.
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250310174502.3708121-5-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Simplify ice_phy_reg_info_eth56g struct definition to include base
address for the very first quad. Use base address info and 'step'
value to determine address for specific PHY quad.
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250310174502.3708121-4-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Refactor the code by changing ice_ptp_init_phc_eth56g function
name to ice_ptp_init_phc_e825, to be consistent with the naming pattern
for other devices.
Signed-off-by: Karol Kolacinski <karol.kolacinski@intel.com>
Signed-off-by: Grzegorz Nitka <grzegorz.nitka@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250310174502.3708121-3-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
E830 supports raw receive and generic transmit checksum offloads.
Raw receive checksum support is provided by hardware calculating the
checksum over the whole packet, regardless of type. The calculated
checksum is provided to driver in the Rx flex descriptor. Then the driver
assigns the checksum to skb->csum and sets skb->ip_summed to
CHECKSUM_COMPLETE.
Generic transmit checksum support is provided by hardware calculating the
checksum given two offsets: the start offset to begin checksum calculation,
and the offset to insert the calculated checksum in the packet. Support is
advertised to the stack using NETIF_F_HW_CSUM feature.
E830 has the following limitations when both generic transmit checksum
offload and TCP Segmentation Offload (TSO) are enabled:
1. Inner packet header modification is not supported. This restriction
includes the inability to alter TCP flags, such as the push flag. As a
result, this limitation can impact the receiver's ability to coalesce
packets, potentially degrading network throughput.
2. The Maximum Segment Size (MSS) is limited to 1023 bytes, which prevents
support of Maximum Transmission Unit (MTU) greater than 1063 bytes.
Therefore NETIF_F_HW_CSUM and NETIF_F_ALL_TSO features are mutually
exclusive. NETIF_F_HW_CSUM hardware feature support is indicated but is not
enabled by default. Instead, IP checksums and NETIF_F_ALL_TSO are the
defaults. Enforcement of mutual exclusivity of NETIF_F_HW_CSUM and
NETIF_F_ALL_TSO is done in ice_set_features(). Mutual exclusivity
of IP checksums and NETIF_F_HW_CSUM is handled by netdev_fix_features().
When NETIF_F_HW_CSUM is requested the provided skb->csum_start and
skb->csum_offset are passed to hardware in the Tx context descriptor
generic checksum (GCS) parameters. Hardware calculates the 1's complement
from skb->csum_start to the end of the packet, and inserts the result in
the packet at skb->csum_offset.
Co-developed-by: Alice Michael <alice.michael@intel.com>
Signed-off-by: Alice Michael <alice.michael@intel.com>
Co-developed-by: Eric Joyner <eric.joyner@intel.com>
Signed-off-by: Eric Joyner <eric.joyner@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Rinitha S <sx.rinitha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://patch.msgid.link/20250310174502.3708121-2-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Before commit 7627a0edef54 ("ata: ahci: Drop low power policy board type")
the ATI AHCI controllers specified board type 'board_ahci' rather than
board type 'board_ahci'. This means that LPM was historically not enabled
for the ATI AHCI controllers.
By looking at commit 7a8526a5cd51 ("libata: Add ATA_HORKAGE_NO_NCQ_ON_ATI
for Samsung 860 and 870 SSD."), it is clear that, for some unknown reason,
that Samsung SSDs do not play nice with ATI AHCI controllers. (When using
other AHCI controllers, NCQ can be enabled on these Samsung SSDs without
issues.)
In a similar way, from user reports, it is clear the ATI AHCI controllers
can enable LPM on e.g. Maxtor HDDs perfectly fine, but when enabling LPM
on certain Samsung SSDs, things break. (E.g. the SSDs will not get detected
by the ATI AHCI controller even after a COMRESET.)
Yet, when using LPM on these Samsung SSDs with other AHCI controllers, e.g.
Intel AHCI controllers, these Samsung drives appear to work perfectly fine.
Considering that the combination of ATI + Samsung, for some unknown reason,
does not seem to work well, disable LPM when detecting an ATI AHCI
controller with a problematic Samsung SSD.
Apply this new ATA_QUIRK_NO_LPM_ON_ATI quirk for all Samsung SSDs that have
already been reported to not play nice with ATI (ATA_QUIRK_NO_NCQ_ON_ATI).
Fixes: 7627a0edef54 ("ata: ahci: Drop low power policy board type")
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Reported-by: Eric <eric.4.debian@grabatoulnz.fr>
Closes: https://lore.kernel.org/linux-ide/Z8SBZMBjvVXA7OAK@eldamar.lan/
Tested-by: Eric <eric.4.debian@grabatoulnz.fr>
Reviewed-by: Damien Le Moal <dlemoal@kernel.org>
Link: https://lore.kernel.org/r/20250317170348.1748671-2-cassel@kernel.org
Signed-off-by: Niklas Cassel <cassel@kernel.org>
|
|
Currently iwlmld_kunit_add_chanctx receives a band, picks a predefined
static chandef, and creates the chanctx from it.
Change it to receive a bandwidth as well. Otherwise, the bandwidth in
the chanctx/phy will be different than what test specified in the
iwl_mld_kunit_link.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250313002008.85a1285d34cd.Ia71cdcd4241fe73501bc93e3cb2c6bb3f631b9ec@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
To allow setting up association/EMLSR states with more flexibility,
change the relevant functions to receive a new struct, iwl_mld_kunit_link,
which will contain all the link parameters (for now just link id, band
and bandwidth).
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250313002008.f336491ccc4e.I6b727765eb394a3dbb78cea71e356be1bdc4a17c@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Allow EMLSR if the bandwidths of the links are unequal if one of the
following conditions is true:
1. in low latency mode
2. bandwidth of the secondary link is greater than the bandwidth of the
primary
3. the primary link is active and is loaded enough to justify EMLSR
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250313002008.150c330711c4.Ifd72d2e076783991852a7f1756948b4f0efb9fea@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We exit EMLSR mode if the FW requested to do so.
To prevent repeated toggling of the EMLSR mode (frequent entry and
exit), add this exit reason to the EMLSR prevention mechanism.
This mechanism avoids re-entering EMLSR for a certain period of time
after multiple exits caused by the same reason.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250313002008.f0e74a7f99af.I447c8788afba85a2a5040ae2c1213b6e05ec14f3@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The channel load logic moves from the FW to the driver.
- Implement the logic: allow EMLSR only if the candidate primary link is
active and if its average channel load exceeds the threshold.
- Remove IWL_MLD_EMLSR_BLOCKED_FW. Instead, treat ESR_RECOMMEND_LEAVE in
the EMLSR_RECOMMENDATION notif as an EXIT reason.
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://patch.msgid.link/20250313002008.6729a8d67815.Iab39bf0982d8cdbb0db701d31854101c2fcf3b64@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Add debugfs file in mld to retrieve TAS status per radio, TAS block list,
current mcc, OEM name and OEM allowed list. This will add ability to get
TAS status to user application via debugfs and required for debugging.
Add the required API definitions and some debug host command utils.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250313002008.66524c6ea198.I1625135284fc075148a55dd9ac629e94ca881fe4@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
The WIPHY_DEBUGFS_READ_WRITE_FILE_OPS_MLD macro is intended to call
read/write handlers with the wiphy lock held. However, the current
implementation uses the MLD_DEBUGFS_READ_WRAPPER macro, which does
not hold the wiphy lock during read operations. This fix updates
the WIPHY_DEBUGFS_READ_WRITE_FILE_OPS_MLD macro to use the
WIPHY_DEBUGFS_READ_WRAPPER_MLD macro instead, ensuring that the
wiphy lock is held during both read and write operations.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250313002008.2001d2335e9d.I607a8bd12efc6d1190cef1fca44279dbdd2756ea@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Introduced the WIPHY_DEBUGFS_READ_FILE_OPS_MLD macro to enable reading
data from the driver while holding the wiphy lock.
This will enable read operations with wiphy locked.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250313002008.b0ddb6b0a144.I1fab63f2c6f52fea61cc5d7b27775aed58adfd8d@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
WIPHY_DEBUGFS_WRITE_HANDLER_WRAPPER
Renamed the macro WIPHY_DEBUGFS_HANDLER_WRAPPER to
WIPHY_DEBUGFS_WRITE_HANDLER_WRAPPER to better reflect its purpose as a
write handler.
Additionally, updated the corresponding macro
WIPHY_DEBUGFS_HANDLER_WRAPPER_MLD to
WIPHY_DEBUGFS_WRITE_HANDLER_WRAPPER_MLD for consistency.
This change does not alter the functionality but enhances the
maintainability of the code.
Signed-off-by: Pagadala Yesu Anjaneyulu <pagadala.yesu.anjaneyulu@intel.com>
Reviewed-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/20250313002008.bb8a1d7907c8.I53325f2f37ccaad2b212d35d10616e06c1555e48@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Link ID to store chandef is still being used as 0 even in case of MLO which
is incorrect. This leads to issue during CAC completion where link 0 as well
gets stopped.
Fixes: 0b7798232eee ("wifi: cfg80211/mac80211: use proper link ID for DFS")
Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com>
Link: https://patch.msgid.link/20250314-fix_starting_cac_during_mlo-v1-1-3b51617d7ea5@oss.qualcomm.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
There are a few conflicts between the work that went
into wireless and that's here now, resolve them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Maxime Chevallier says:
====================
net: phy: Rework linkmodes handling in a dedicated file
This is V5 of the phy_caps series. In a nutshell, this series reworks the way
we maintain the list of speed/duplex capablities for each linkmode so that we
no longer have multiple definition of these associations.
That will help making sure that when people add new linkmodes in
include/uapi/linux/ethtool.h, they don't have to update phylib and phylink as
well, making the process more straightforward and less error-prone.
It also generalises the phy_caps interface to be able to lookup linkmodes
from phy_interface_t, which is needed for the multi-port work I've been working
on for a while.
This V5 addresse Russell's and Paolo's reviews, namely :
- Error out when encountering an unknown SPEED_XXX setting
It prints an error and fails to initialize phylib. I've tested by
introducing a dummy 1.6T speed, I guess it's only a matter of time
before that actually happens :)
- Deal more gracefully with the fixed-link settings, keeping some level of
compatibility with what we had before by making sure we report a
single BaseT mode like before.
V1 : https://lore.kernel.org/netdev/20250222142727.894124-1-maxime.chevallier@bootlin.com/
V2 : https://lore.kernel.org/netdev/20250226100929.1646454-1-maxime.chevallier@bootlin.com/
V3 : https://lore.kernel.org/netdev/20250228145540.2209551-1-maxime.chevallier@bootlin.com/
V4 : https://lore.kernel.org/netdev/20250303090321.805785-1-maxime.chevallier@bootlin.com/
====================
Link: https://patch.msgid.link/20250307173611.129125-1-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Phylink has internal code to get the MAC capabilities of a given PHY
interface (what are the supported speed and duplex).
Extract that into phy_caps, but use the link_capa for conversion. Add an
internal phylink helper for the link caps -> mac caps conversion, and
use this in phylink_caps_to_linkmodes().
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-14-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
phylink_caps_to_linkmodes() is used to derive a list of linkmodes that
can be conceivably exposed using a given set of speeds and duplex
through phylink's MAC capabilities.
This list can be derived from the link_caps array in phy_caps, provided
we convert the MAC capabilities into a LINK_CAPA bitmask first.
Introduce an internal phylink helper phylink_caps_to_link_caps() to
convert from MAC capabilities into phy_caps, then phy_caps_linkmodes()
to do the link_caps -> linkmodes conversion.
This avoids having to update phylink for every new linkmode.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-13-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
phylink allows MAC drivers to report the capabilities in terms of speed,
duplex and pause support. This is done through a dedicated set of enum
values in the form of the MAC_ capabilities. They are very close to what
the LINK_CAPA_xxx can express, with the difference that LINK_CAPA don't
have any information about Pause/Asym Pause support.
To prepare converting phylink to using the phy_caps, add the mapping
between MAC capabilities and phy_caps. While doing so, we move the
phylink_caps_params array up a bit to simplify future commits.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-12-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The phy_settings array is no longer relevant as it has now been replaced
by the link_caps array and associated phy_caps helpers.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-11-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When phylink creates a fixed-link configuration, it finds a matching
linkmode to set as the advertised, lp_advertising and supported modes
based on the speed and duplex of the fixed link.
Use the newly introduced phy_caps_lookup to get these modes instead of
phy_lookup_settings(). This has the side effect that the matched
settings and configured linkmodes may now contain several linkmodes (the
intersection of supported linkmodes from the phylink settings and the
linkmodes that match speed/duplex) instead of the one from
phy_lookup_settings().
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-10-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
When configuring PHY advertising with autoneg disabled, we lookd for an
exact linkmode to advertise and configure for the requested Speed and
Duplex, specially at or over 1G.
Using phy_caps_lookup allows us to build a list of the supported
linkmodes at that speed that we can advertise instead of the first mode
that matches.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-9-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
As the link_caps array is efficient for <speed,duplex> lookups,
implement a function for speed/duplex lookups that matches a given
mask. This replicates to some extent the phy_lookup_settings()
behaviour, matching full link_capabilities instead of a single linkmode.
phy.c's phy_santize_settings() and phylink's
phylink_ethtool_ksettings_set() performs such lookup using the
phy_settings table, but are only interested in the actual speed/duplex
that were matched, rathet than the individual linkmode.
Similar to phy_lookup_settings(), the newly introduced phy_caps_lookup()
will run through the link_caps[] array by descending speed/duplex order.
If the link_capabilities for a given <speed/duplex> tuple intersects the
passed linkmodes, we consider that a match.
Similar to phy_lookup_settings(), we also allow passing an 'exact'
boolean, allowing non-exact match. Here, we MUST always match the
linkmodes mask, but we allow matching on lower speed settings.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-8-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In several occasions, phylib needs to lookup a set of matching speed and
duplex against a given linkmode set. Instead of relying on the
phy_settings array and thus iterate over the whole linkmodes list, use
the link_capabilities array to lookup these matches, as we aren't
interested in the actual link setting that matches but rather the speed
and duplex for that setting.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-7-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
With the link_capabilities array, it's trivial to validate a given mask
againts a <speed, duplex> tuple. Create a helper for that purpose, and
use it to replace a phy_settings lookup in phy_check_valid();
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-6-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Convert the __set_linkmode_max_speed to use the link_capabilities array.
This makes it easy to clamp the linkmodes to a given max speed.
Introduce a new helper phy_caps_linkmode_max_speed to replace the
previous one that used phy_settings.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-5-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Use the newly introduced link_capabilities array to derive the list of
possible speeds when given a combination of linkmodes. As
link_capabilities is indexed by speed, we don't have to iterate the
whole phy_settings array.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-4-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The canonical definition for all the link modes is in linux/ethtool.h,
which is complemented by the link_mode_params array stored in
net/ethtool/common.h . That array contains all the metadata about each
of these modes, including the Speed and Duplex information.
Phylib and phylink needs that information as well for internal
management of the link, which was done by duplicating that information
in locally-stored arrays and lookup functions. This makes it easy for
developpers adding new modes to forget modifying phylib and phylink
accordingly.
However, the link_mode_params array in net/ethtool/common.c is fairly
inefficient to search through, as it isn't sorted in any manner. Phylib
and phylink perform a lot of lookup operations, mostly to filter modes
by speed and/or duplex.
We therefore introduce the link_caps private array in phy_caps.c, that
indexes linkmodes in a more efficient manner. Each element associated a
tuple <speed, duplex> to a bitfield of all the linkmodes runs at these
speed/duplex.
We end-up with an array that's fairly short, easily addressable and that
it optimised for the typical use-cases of phylib/phylink.
That array is initialized at the same time as phylib. As the
link_mode_params array is part of the net stack, which phylink depends
on, it should always be accessible from phylib.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-3-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
link_mode_params contains a lookup table of all 802.3 link modes that
are currently supported with structured data about each mode's speed,
duplex, number of lanes and mediums.
As a preparation for a port representation, export that table for the
rest of the net stack to use.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Link: https://patch.msgid.link/20250307173611.129125-2-maxime.chevallier@bootlin.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
LSMs often inspect the path.mnt of files in the security hooks, and this
causes a NULL deref in efivarfs_pm_notify() because the path is
constructed with a NULL path.mnt.
Fix by obtaining from vfs_kern_mount() instead, and being very careful
to ensure that deactivate_super() (potentially triggered by a racing
userspace umount) is not called directly from the notifier, because it
would deadlock when efivarfs_kill_sb() tried to unregister the notifier
chain.
[ Al notes:
Umm... That's probably safe, but not as a long-term solution -
it's too intimately dependent upon fs/super.c internals. The
reasons why you can't run into ->s_umount deadlock here are
non-trivial... ]
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Link: https://lore.kernel.org/r/e54e6a2f-1178-4980-b771-4d9bafc2aa47@tnxip.de
Link: https://lore.kernel.org/r/3e998bf87638a442cbc6864cdcd3d8d9e08ce3e3.camel@HansenPartnership.com
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull misc hotfixes from Andrew Morton:
"15 hotfixes. 7 are cc:stable and the remainder address post-6.13
issues or aren't considered necessary for -stable kernels.
13 are for MM and the other two are for squashfs and procfs.
All are singletons. Please see the individual changelogs for details"
* tag 'mm-hotfixes-stable-2025-03-17-20-09' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm:
mm/page_alloc: fix memory accept before watermarks gets initialized
mm: decline to manipulate the refcount on a slab page
memcg: drain obj stock on cpu hotplug teardown
mm/huge_memory: drop beyond-EOF folios with the right number of refs
selftests/mm: run_vmtests.sh: fix half_ufd_size_MB calculation
mm: fix error handling in __filemap_get_folio() with FGP_NOWAIT
mm: memcontrol: fix swap counter leak from offline cgroup
mm/vma: do not register private-anon mappings with khugepaged during mmap
squashfs: fix invalid pointer dereference in squashfs_cache_delete
mm/migrate: fix shmem xarray update during migration
mm/hugetlb: fix surplus pages in dissolve_free_huge_page()
mm/damon/core: initialize damos->walk_completed in damon_new_scheme()
mm/damon: respect core layer filters' allowance decision on ops layer
filemap: move prefaulting out of hot write path
proc: fix UAF in proc_get_inode()
|
|
Unfortunately I no longer have time to meaningfully take part in the
linux kernel development.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull SoC fixes from Arnd Bergmann:
"The majority of these last fixes are for devicetree files.
These address two important regressions for the Qualcomm SMMU and the
Raspberry Pi 4 USB controller, as well as a larger number of patches
fixing minor mistakes in board specific files for Rockchips, i.MX,
starfive and broadcom.
The non-DT changes are
- A fix for an old boot regression on Renesas shmobile chips
- Another boot time regression for for the Qualcomm PDR SoC driver,
among a few other Qualcomm firmware driver fixes for efivars and
tzmem
- Minor Kconfig fixes for davinci and OMAP1
- Minor code fixes for sparx5 reset controllers, OMAP memory
controller, i.MX SCU, cpufreq and SoC drivers and a Hisilicon SoC
driver
- One more update to the Asahi maintainers, adding Neal Gompa as a
reviewer"
* tag 'soc-fixes-6.14-2' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (35 commits)
ARM: davinci: da850: fix selecting ARCH_DAVINCI_DA8XX
soc: hisilicon: kunpeng_hccs: Fix incorrect string assembly
memory: omap-gpmc: drop no compatible check
reset: mchp: sparx5: Fix for lan966x
ARM: shmobile: smp: Enforce shmobile_smp_* alignment
MAINTAINERS: Add myself (Neal Gompa) as a reviewer for ARM Apple support
MAINTAINERS: Add apple-spi driver & binding files
arm64: dts: rockchip: slow down emmc freq for rock 5 itx
ARM: dts: BCM5301X: Fix switch port labels of ASUS RT-AC3200
ARM: dts: BCM5301X: Fix switch port labels of ASUS RT-AC5300
ARM: dts: bcm2711: Don't mark timer regs unconfigured
ARM: OMAP1: select CONFIG_GENERIC_IRQ_CHIP
arm64: dts: rockchip: Add missing PCIe supplies to RockPro64 board dtsi
arm64: dts: rockchip: Add avdd HDMI supplies to RockPro64 board dtsi
arm64: dts: rockchip: Remove undocumented sdmmc property from lubancat-1
arm64: dts: rockchip: fix pinmux of UART5 for PX30 Ringneck on Haikou
arm64: dts: rockchip: fix pinmux of UART0 for PX30 Ringneck on Haikou
arm64: dts: rockchip: fix u2phy1_host status for NanoPi R4S
arm64: dts: bcm2712: PL011 UARTs are actually r1p5
ARM: dts: bcm2711: PL011 UARTs are actually r1p5
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace
Pull probes fixes from Masami Hiramatsu:
- Clean up tprobe correctly when module unload
Tracepoint probes do not set TRACEPOINT_STUB on the 'tpoint' pointer
when unloading a module, thus they show as a normal 'fprobe' instead
of 'tprobe' and never come back
- Fix leakage of tprobe module refcount
When a tprobe's target module is loaded, it gets the module's
refcount in the module notifier but forgot to put it after
registering the probe on it.
Fix it by getting the refcount only when registering tprobe.
* tag 'probes-fixes-v6.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/trace/linux-trace:
tracing: tprobe-events: Fix leakage of module refcount
tracing: tprobe-events: Fix to clean up tprobe correctly when module unload
|
|
'net-stmmac-avoid-unnecessary-work-in-stmmac_release-stmmac_dvr_remove'
Russell King says:
====================
net: stmmac: avoid unnecessary work in stmmac_release()/stmmac_dvr_remove()
This small series is a subset of a RFC I sent earlier. These two
patches remove code that is unnecessary and/or wrong in these paths.
Details in each commit.
====================
Link: https://patch.msgid.link/Z87bpDd7QYYVU0ML@shell.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
stmmac_release() calls phylink_stop() and then goes on to call
stmmac_mac_set(, false). However, phylink_stop() will call
stmmac_mac_link_down() before returning, which will do this work.
Remove this unnecessary call.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Furong Xu <0x1207@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1trcI6-005rn8-GV@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
While the network device is registered, it is published to userspace,
and thus userspace can change its state. This means calling
functions such as stmmac_stop_all_dma() and stmmac_mac_set() are
racy.
Moreover, unregister_netdev() will unpublish the network device, and
then if appropriate call the .ndo_stop() method, which is
stmmac_release(). This will first call phylink_stop() which will
synchronously take the link down, resulting in stmmac_mac_link_down()
and stmmac_mac_set(, false) being called.
stmmac_release() will also call stmmac_stop_all_dma().
Consequently, neither of these two functions need to called prior
to unregister_netdev() as that will safely call paths that will
result in this work being done if necessary.
Remove these redundant racy calls.
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Furong Xu <0x1207@gmail.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1trcI1-005rn2-CZ@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Expand on the requirements of the .pcs_config() method documentation,
specifically mentioning that it should cause minimal disruption to
an established link, and that it should return a positive non-zero
value when requiring the .pcs_an_restart() method to be called.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1trb24-005oVq-Is@rmk-PC.armlinux.org.uk
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Lenovo ThinkPad Hybrid USB-C with USB-A Dock (17ef:a359) is affected by
the same problem as the Lenovo Powered USB-C Travel Hub (17ef:721e):
Both are based on the Realtek RTL8153B chip used to use the cdc_ether
driver. However, using this driver, with the system suspended the device
constantly sends pause-frames as soon as the receive buffer fills up.
This causes issues with other devices, where some Ethernet switches stop
forwarding packets altogether.
Using the Realtek driver (r8152) fixes this issue. Pause frames are no
longer sent while the host system is suspended.
Cc: Leon Schuermann <leon@is.currently.online>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Oliver Neukum <oliver@neukum.org> (maintainer:USB CDC ETHERNET DRIVER)
Cc: netdev@vger.kernel.org (open list:NETWORKING DRIVERS)
Link: https://git.kernel.org/netdev/net/c/cb82a54904a9
Link: https://git.kernel.org/netdev/net/c/2284bbd0cf39
Link: https://www.lenovo.com/de/de/p/accessories-and-software/docking/docking-usb-docks/40af0135eu
Signed-off-by: Philipp Hahn <phahn-oss@avm.de>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Link: https://patch.msgid.link/484336aad52d14ccf061b535bc19ef6396ef5120.1741601523.git.p.hahn@avm.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
intel_tsn_lane_is_available()
Fix the warning "warn: missing error code? 'ret'" in the
intel_tsn_lane_is_available() function.
The function now returns 0 to indicate that a TSN lane was found and
returns -EINVAL when it is not found.
Fixes: a42f6b3f1cc1 ("net: stmmac: configure SerDes according to the interface mode")
Signed-off-by: Choong Yong Liang <yong.liang.choong@linux.intel.com>
Reviewed-by: Kory Maincent <kory.maincent@bootlin.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250310050835.808870-1-yong.liang.choong@linux.intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Heiner Kallweit says:
====================
net: phy: clean up PHY package MMD access functions
Move declarations of the functions with users to phylib.h, and remove
unused functions.
====================
Link: https://patch.msgid.link/b624fcb7-b493-461a-a0b5-9ca7e9d767bc@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
These functions have never had a user, so remove them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/5792e2cd-6f0a-4f7d-a5ef-b932f94d82f3@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
phylib.h
These functions are used by PHY drivers only, therefore move their
declaration to phylib.h.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/406c8a20-b62e-4ee3-b174-b566724a0876@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Tariq Toukan says:
====================
mlx5: Support HWS flow meter/sampler actions in FS core
This series by Moshe adds support for flow meter and flow sampler HW
Steering actions in FS core level. As these actions can be shared by
multiple rules, these patches use refcounts to manage the HWS actions
sharing in FS core level.
====================
Link: https://patch.msgid.link/1741543663-22123-1-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add support for HW Steering action of flow sampler destination. For each
flow sampler created cache the hws action by sampler id as a key. Hold
refcount for each rule using the cached action.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/1741543663-22123-4-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Add support for HW Steering action of flow meter range. Flow meters
range can use one HWS action for the whole range. Thus, share a cached
HWS action among rules that use same flow meter object range. Hold
refcount for each rule using the cached action.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/1741543663-22123-3-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Counters HWS actions are shared using refcount, to create action on
demand by flow steering rule and destroy only when no rules are using
the action. The method is extensible to other HWS action types, such as
flow meter and sampler actions, in the downstream patches.
Add an API to facilitate the reuse of get/put logic for HWS actions
shared by refcount.
Signed-off-by: Moshe Shemesh <moshe@nvidia.com>
Reviewed-by: Mark Bloch <mbloch@nvidia.com>
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://patch.msgid.link/1741543663-22123-2-git-send-email-tariqt@nvidia.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
syzbot warns about a potential deadlock, but this is a false positive
resulting from a missing lockdep annotation: iterate_dir() locks the
parent whereas the inode_lock() it warns about locks the child, which is
guaranteed to be a different lock.
So use inode_lock_nested() instead with the appropriate lock class.
Reported-by: syzbot+019072ad24ab1d948228@syzkaller.appspotmail.com
Suggested-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
|
|
Chia-Yu Chang says:
====================
AccECN protocol preparation patch series
Please find the v7
v7 (03-Mar-2025)
- Move 2 new patches added in v6 to the next AccECN patch series
v6 (27-Dec-2024)
- Avoid removing removing the potential CA_ACK_WIN_UPDATE in ack_ev_flags of patch #1 (Eric Dumazet <edumazet@google.com>)
- Add reviewed-by tag in patches #2, #3, #4, #5, #6, #7, #8, #12, #14
- Foloiwng 2 new pathces are added after patch #9 (Patch that adds SKB_GSO_TCP_ACCECN)
* New patch #10 to replace exisiting SKB_GSO_TCP_ECN with SKB_GSO_TCP_ACCECN in the driver to avoid CWR flag corruption
* New patch #11 adds AccECN for virtio by adding new negotiation flag (VIRTIO_NET_F_HOST/GUEST_ACCECN) in feature handshake and translating Accurate ECN GSO flag between virtio_net_hdr (VIRTIO_NET_HDR_GSO_ACCECN) and skb header (SKB_GSO_TCP_ACCECN)
- Add detailed changelog and comments in #13 (Eric Dumazet <edumazet@google.com>)
- Move patch #14 to the next AccECN patch series (Eric Dumazet <edumazet@google.com>)
v5 (5-Nov-2024)
- Add helper function "tcp_flags_ntohs" to preserve last 2 bytes of TCP flags of patch #4 (Paolo Abeni <pabeni@redhat.com>)
- Fix reverse X-max tree order of patches #4, #11 (Paolo Abeni <pabeni@redhat.com>)
- Rename variable "delta" as "timestamp_delta" of patch #2 fo clariety
- Remove patch #14 in this series (Paolo Abeni <pabeni@redhat.com>, Joel Granados <joel.granados@kernel.org>)
v4 (21-Oct-2024)
- Fix line length warning of patches #2, #4, #8, #10, #11, #14
- Fix spaces preferred around '|' (ctx:VxV) warning of patch #7
- Add missing CC'ed of patches #4, #12, #14
v3 (19-Oct-2024)
- Fix build error in v2
v2 (18-Oct-2024)
- Fix warning caused by NETIF_F_GSO_ACCECN_BIT in patch #9 (Jakub Kicinski <kuba@kernel.org>)
The full patch series can be found in
https://github.com/L4STeam/linux-net-next/commits/upstream_l4steam/
The Accurate ECN draft can be found in
https://datatracker.ietf.org/doc/html/draft-ietf-tcpm-accurate-ecn-28
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
