| Age | Commit message (Collapse) | Author |
|---|
|
This is another preliminary patch for USB MIDI 2.0 gadget driver.
Add a new flag, no_process_stream, to snd_ump for suppressing the UMP
Stream message handling in UMP core.
Link: https://lore.kernel.org/r/20230621110241.4751-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This is a preliminary patch for MIDI 2.0 USB gadget driver.
Export a new helper to allow changing the current MIDI protocol from
the outside.
Link: https://lore.kernel.org/r/20230621110241.4751-2-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Always add buses to the stream->master_list in a fixed order.
The unique bus->id is used to order the adding of buses to the
list.
This prevents lockdep asserts and possible deadlocks on streams
that have multiple buses.
sdw_acquire_bus_lock() takes bus_lock in the order that buses
are listed in stream->master_list. do_bank_switch() takes all
the msg_lock in the same order.
To prevent a lockdep assert, and a possible real deadlock, the
relative order of taking these mutexes must always be the same.
For example, if a stream takes the mutexes in the order
(bus0, bus1) lockdep will assert if another stream takes them
in the order (bus1, bus0).
More complex relative ordering will also assert, for example
if two streams take (bus0, bus1) and (bus1, bus2), then a third
stream takes (bus2, bus0).
Previously sdw_stream_add_master() simply added the given bus
to the end of the list, requiring the caller to guarantee that
buses are added in a fixed order. This isn't reasonable or
necessary - it's an internal implementation detail that should
not be exposed by the API. It doesn't really make sense when
there could be multiple independent calling drivers, to say
"you must add your buses in the same order as a different driver,
that you don't know about, added them".
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230615141208.679011-2-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Give the bus_lock and msg_lock of each bus a different unique key
so that it is possible to acquire the locks of multiple buses
without lockdep asserting a possible deadlock.
Using mutex_init() to initialize a mutex gives all those mutexes
the same lock class. Lockdep checking treats it as an error to
attempt to take a mutex while already holding a mutex of the same
class. This causes a lockdep assert when sdw_acquire_bus_lock()
attempts to lock multiple buses, and when do_bank_switch() takes
multiple msg_lock.
[ 138.697350] WARNING: possible recursive locking detected
[ 138.697366] 6.3.0-test #1 Tainted: G E
[ 138.697380] --------------------------------------------
[ 138.697394] play/903 is trying to acquire lock:
[ 138.697409] ffff99b8c41aa8c8 (&bus->bus_lock){+.+.}-{3:3}, at:
sdw_prepare_stream+0x52/0x2e0
[ 138.697443]
but task is already holding lock:
[ 138.697468] ffff99b8c41af8c8 (&bus->bus_lock){+.+.}-{3:3}, at:
sdw_prepare_stream+0x52/0x2e0
[ 138.697493]
other info that might help us debug this:
[ 138.697521] Possible unsafe locking scenario:
[ 138.697540] CPU0
[ 138.697550] ----
[ 138.697559] lock(&bus->bus_lock);
[ 138.697570] lock(&bus->bus_lock);
[ 138.697581]
*** DEADLOCK ***
Giving each mutex a unique key allows multiple to be held
without triggering a lockdep assert. But note that it does not
allow them to be taken in one order then a different order.
If two mutexes are taken in the order A, B then they must
always be taken in that order otherwise they could deadlock.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20230615141208.679011-1-rf@opensource.cirrus.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
The 'qcom_swrm_ctrl->pconfig' has size of QCOM_SDW_MAX_PORTS (14),
however we index it starting from 1, not 0, to match real port numbers.
This can lead to writing port config past 'pconfig' bounds and
overwriting next member of 'qcom_swrm_ctrl' struct. Reported also by
smatch:
drivers/soundwire/qcom.c:1269 qcom_swrm_get_port_config() error: buffer overflow 'ctrl->pconfig' 14 <= 14
Fixes: 9916c02ccd74 ("soundwire: qcom: cleanup internal port config indexing")
Cc: <stable@vger.kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <error27@gmail.com>
Link: https://lore.kernel.org/r/202305201301.sCJ8UDKV-lkp@intel.com/
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Link: https://lore.kernel.org/r/20230601102525.609627-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
We're using pci_irq_vector() to obtain the interrupt number and then
bind it to the CPU start perf under the protection of spinlock in
pmu::start(). pci_irq_vector() might sleep since [1] because it will
call msi_domain_get_virq() to get the MSI interrupt number and it
needs to acquire dev->msi.data->mutex. Getting a mutex will sleep on
contention. So use pci_irq_vector() in an atomic context is problematic.
This patch cached the interrupt number in the probe() and uses the
cached data instead to avoid potential sleep.
[1] commit 82ff8e6b78fc ("PCI/MSI: Use msi_get_virq() in pci_get_vector()")
Fixes: ff0de066b463 ("hwtracing: hisi_ptt: Add trace function support for HiSilicon PCIe Tune and Trace device")
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20230621092804.15120-6-yangyicong@huawei.com
|
|
The PTT trace collects PCIe TLP headers from the PCIe link and don't
have the ability to exclude certain context. It doesn't support itrace
as well. So replace PERF_PMU_CAP_ITRACE with PERF_PMU_CAP_NO_EXCLUDE.
This will greatly save the storage of final data. Tested tracing idle
link for ~15s, without this patch we'll collect ~28.682MB data for
additional information and with this patch it reduced to ~0.226MB.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Tested-by: Junhao He <hejunhao3@huawei.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20230621092804.15120-5-yangyicong@huawei.com
|
|
The PTT can only filter the traced TLP headers by the Root Ports or the
Requester ID of the Endpoint, which are located on the same PCIe core of
the PTT device. The filter value used is derived from the BDF number of
the supported Root Port or the Endpoint. It's not friendly enough for the
users since it requires the user to be familiar enough with the platform
and calculate the filter value manually.
This patch export the available filters through sysfs. Each available
filters is presented as an individual file with the name of the BDF
number of the related PCIe device. The files are created under
$(PTT PMU dir)/available_root_port_filters and
$(PTT PMU dir)/available_requester_filters respectively. The filter
value can be known by reading the related file.
Then the users can easily know the available filters for trace and get
the filter values without calculating.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20230621092804.15120-4-yangyicong@huawei.com
|
|
The PCIe devices supported by the PTT trace can be removed/rescanned by
hotplug or through sysfs. Add support for dynamically updating the
available filter list by registering a PCI bus notifier block. Then user
can always get latest information about available tracing filters and
driver can block the invalid filters of which related devices no longer
exist in the system.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20230621092804.15120-3-yangyicong@huawei.com
|
|
Factor out the allocation and release of filters. This will make it easier
to extend and manage the function of the filter.
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Link: https://lore.kernel.org/r/20230621092804.15120-2-yangyicong@huawei.com
|
|
The ace2x driver can be build with or without mlink support, but
when SND_SOC_SOF_HDA_MLINK is set to =m and soundwire is built-in,
it fails with a link error:
ld.lld: error: undefined symbol: hdac_bus_eml_sdw_wait_syncpu_unlocked
>>> referenced by intel_ace2x.c
>>> drivers/soundwire/intel_ace2x.o:(intel_link_power_up) in archive vmlinux.a
ld.lld: error: undefined symbol: hdac_bus_eml_sdw_sync_arm_unlocked
>>> referenced by intel_ace2x.c
>>> drivers/soundwire/intel_ace2x.o:(intel_sync_arm) in archive vmlinux.a
Add a Kconfig dependency that prevents that broken configuration but
still allows soundwire to be a loadable module instead.
Fixes: 4d1e2464a1104 ("soundwire: intel_ace2x: add sync_arm/sync_go helpers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20230616090932.2714714-1-arnd@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Add the missing MODULE_FIRMWARE macro for "3826.eeprom".
Signed-off-by: Juerg Haefliger <juerg.haefliger@canonical.com>
Acked-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616121917.1034761-1-juerg.haefliger@canonical.com
|
|
For filenames that begin with . and are between 2 and 5 characters long,
UDF charset conversion code would read uninitialized memory in the
output buffer. The only practical impact is that the name may be prepended a
"unification hash" when it is not actually needed but still it is good
to fix this.
Reported-by: syzbot+cd311b1e43cc25f90d18@syzkaller.appspotmail.com
Link: https://lore.kernel.org/all/000000000000e2638a05fe9dc8f9@google.com
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
ath11k has a wiki and a separate page about reporting bugs, add those so
hopefully people find them easier.
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230614144704.505553-3-kvalo@kernel.org
|
|
ath9k patches go to my ath.git tree, document that.
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230614144704.505553-2-kvalo@kernel.org
|
|
Felix has a git tree for mt76 patches, document that.
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230614144704.505553-1-kvalo@kernel.org
|
|
A firmware contains basic header, sections and optional dynamic header.
Define them by a struct, so it will be easier to understand the layout,
and also simply access these elements.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616060601.28460-1-pkshih@realtek.com
|
|
Some old declarations about TX power stuffs were named with confusing
`_max`. But, they mean "the number of". So we change them to be named
with `_num`.
(No logic is changed.)
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616060523.28396-1-pkshih@realtek.com
|
|
RTL8851B is a chip with only single RF path, and it must use 1 TX power
value for transmission, so force 1 TX power value to prevent hardware
logic gets wrong TX power values randomly in certain samples.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230615130442.18116-6-pkshih@realtek.com
|
|
The main change is to adjust RX calibration groups from {0,1,2,3} to {0,2}
in 5 GHz, so reduce elements from 4 to 2, and use index to iterate them.
Meanwhile, always do RX narrowband calibration (ID_NBRXK) for each group.
NCTL is used to assist IQK, so also update NCTL to 0x6 along with internal
tag HALRF_029_00_103.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230615130442.18116-5-pkshih@realtek.com
|
|
LCK is short for LC Tank calibration. To keep RF performance, do this
calibration if difference of thermal value is over a threshold.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230615130442.18116-4-pkshih@realtek.com
|
|
Update 8851B TX power tables to RF version R28.
TX power tables' changes:
* TX power limit and TX power shape:
update 5 GHz configurations for FCC and IC
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230615130442.18116-3-pkshih@realtek.com
|
|
Update 8851b radio A parameters to R28 along with internal HALRF_029_00_103
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230615130442.18116-2-pkshih@realtek.com
|
|
Without this patch, firmware only track beacons for port 0 and since
we will always start AP on port 0, this results in misbehavior of
power saving mode on other ports after AP stops.
The "default port" H2C command is used to notify which port should
firmware track. Update the correct settings to firmware so power
saving mode can work properly.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616125540.36877-7-pkshih@realtek.com
|
|
Since register based H2C commands don't need endian conversion.
Introduce a new API that don't do conversion and send it directly.
New caller are expected to encode with cpu order and gradually
replace the old ones.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616125540.36877-6-pkshih@realtek.com
|
|
When traversing channel list, TX in high queue should be disabled
along with beacon function, so packets won't be sent to incorrect
channels.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616125540.36877-5-pkshih@realtek.com
|
|
The flush period may not always intersect with DTIM and when that
happens, an error log "timed out to flush pci TX ring[6]" is shown.
Bypass this since hardware will do proper transmission on the next
DTIM period for broadcast/multicast packets in high queue.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616125540.36877-4-pkshih@realtek.com
|
|
Broadcast and multicast packets in high queue should be transmitted
all at once during DTIM. But without proper settings, hardware fails
to recognize that there are multiple packets and fetches only one.
Fix this by signaling hardware with more data bit set when there are
packets in the high queue.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616125540.36877-3-pkshih@realtek.com
|
|
Remove macros that set TX descriptors. Use struct and
le32_encode_bits() with mask definitions.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616125540.36877-2-pkshih@realtek.com
|
|
In the wpa_supplicant rekey flow, it sends an EAPOL packet 4/4 through
nl80211_tx_control_port() and triggers wake_tx_queue() in the driver.
Then, it sends nl80211_new_key() to configure a new key in mac80211.
However, in wake_tx_queue(), a workqueue is used to process the tx packet,
which might cause the driver to process the EAPOL packet later than
nl80211_new_key(). As a result, the EAPOL 4/4 packet is dropped by mac80211
due to the rekey configuration being finished. The EAPOL packets belongs to
VO packets that need high priority. Therefore, we process VO packets
directly without workqueue to ensure that packets can process immediately.
VO is normally used by voice application that is low traffic load and low
latency, that doesn't affect user experience.
We test iperf with VO packets(iperf3 -P4 -u -b 10000M -S 0xdf)
before after
TX throughput 162M 162M
ping RTT 3.8ms 3.7ms
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230616031713.16769-1-pkshih@realtek.com
|
|
For combo chips, antennas were controlled by bluetooth only during
power on. If WiFi wish to do transmission, notification to the coexistence
module are required. Previously we only do this before authentication.
To allow transmission before auth, such as management TX, now we start
the initiation of coexistence earlier so antennas are shared between
WiFi and bluetooth after set_channel(), and frames could then be sent.
Signed-off-by: Po-Hao Huang <phhuang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20230615114348.7193-1-pkshih@realtek.com
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into soc/defconfig
- Enable mt6357 PMIC needed for mt8365 EVK
- Enable device for power button on several PMICs
* tag 'v6.4-next-defconfig' of https://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
arm64: defconfig: enable Mediatek PMIC key
arm64: defconfig: enable MT6357 regulator
Link: https://lore.kernel.org/r/92e336ca-bbbb-6d6c-297a-13deaae4138b@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux into soc/defconfig
TI K3 defconfig updates
Enable AM62 Verdin board peripherals
Enable UBIFS support for OSPI NOR/NAND Filesystem on K3 platforms
* tag 'ti-k3-config-for-v6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux:
arm64: defconfig: Enable UBIFS
arm64: defconfig: enable drivers for Verdin AM62
Link: https://lore.kernel.org/r/97a49740-32e7-f899-d153-743b5a57eba7@ti.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/defconfig
More Qualcomm ARM64 defconfig updates for v6.5
This enables various clock drivers for QCM2290, SM6115 and SC8280XP.
Furhter, the interconnect and the MSM power manageer (MPM) drivers are
enabled to allow QCM2290 to boot.
* tag 'qcom-arm64-defconfig-for-6.5-2' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: defconfig: Build SM6115 display and GPU clock controller drivers
arm64: defconfig: Build display clock controller driver for QCM2290
arm64: defconfig: Build interconnect driver for QCM2290
arm64: defconfig: Build Global Clock Controller driver for QCM2290
arm64: defconfig: Build MSM power manager driver
arm64: defconfig: Enable sc828x0xp lpasscc clock controller
Link: https://lore.kernel.org/r/20230615154119.1460952-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into soc/defconfig
Qualcomm ARM64 defconfig updates for v6.5
Enable the FSA4480 driver to enable USB Type-C altmode on devices such
as SM8350 and SM8450 HDK. Enable the IPQ6018 APSS clock and PLL
controller for CPU scaling, and enable GPU clock river for SA8775P.
* tag 'qcom-arm64-defconfig-for-6.5' of https://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
arm64: defconfig: Enable ipq6018 apss clock and PLL controller
arm64: defconfig: enable FSA4480 driver as module
arm64: defconfig: enable the SA8775P GPUCC driver
Link: https://lore.kernel.org/r/20230610170955.2478831-1-andersson@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into soc/defconfig
i.MX defconfig changes for 6.5:
- Remove KERNEL_LZO and FW_LOADER_USER_HELPER from imx_v6_v7_defconfig.
- Enable i.MX8M video capture drivers and TI SN65DSI83 driver for arm64
defconfig.
* tag 'imx-defconfig-6.5' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: defconfig: Enable the TI SN65DSI83 driver
ARM: imx_v6_v7_defconfig: Remove KERNEL_LZO config
arm64: defconfig: Enable video capture drivers on imx8mm/imx8mn
ARM: imx_v6_v7_defconfig: Remove firmware loader helper
Link: https://lore.kernel.org/r/20230610072530.418847-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
We currently allow to create perf link for program with
expected_attach_type == BPF_TRACE_KPROBE_MULTI.
This will cause crash when we call helpers like get_attach_cookie or
get_func_ip in such program, because it will call the kprobe_multi's
version (current->bpf_ctx context setup) of those helpers while it
expects perf_link's current->bpf_ctx context setup.
Making sure that we use BPF_TRACE_KPROBE_MULTI expected_attach_type
only for programs attaching through kprobe_multi link.
Fixes: ca74823c6e16 ("bpf: Add cookie support to programs attached with kprobe multi link")
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Andrii Nakryiko <andrii@kernel.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Link: https://lore.kernel.org/bpf/20230618131414.75649-1-jolsa@kernel.org
|
|
When building a kernel with LLVM=1, LLVM_IAS=0 and CONFIG_KASAN=y, LLVM
leaves DWARF tags for the "asan.module_ctor" & co symbols. In turn,
pahole creates BTF_KIND_FUNC entries for these and this makes the BTF
metadata validation fail because they contain a dot.
In a dramatic turn of event, this BTF verification failure can cause
the netfilter_bpf initialization to fail, causing netfilter_core to
free the netfilter_helper hashmap and netfilter_ftp to trigger a
use-after-free. The risk of u-a-f in netfilter will be addressed
separately but the existence of "asan.module_ctor" debug info under some
build conditions sounds like a good enough reason to accept functions
that contain dots in BTF.
Although using only LLVM=1 is the recommended way to compile clang-based
kernels, users can certainly do LLVM=1, LLVM_IAS=0 as well and we still
try to support that combination according to Nick. To clarify:
- > v5.10 kernel, LLVM=1 (LLVM_IAS=0 is not the default) is recommended,
but user can still have LLVM=1, LLVM_IAS=0 to trigger the issue
- <= 5.10 kernel, LLVM=1 (LLVM_IAS=0 is the default) is recommended in
which case GNU as will be used
Fixes: 1dc92851849c ("bpf: kernel side support for BTF Var and DataSec")
Signed-off-by: Florent Revest <revest@chromium.org>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Andrii Nakryiko <andrii@kernel.org>
Cc: Yonghong Song <yhs@meta.com>
Cc: Nick Desaulniers <ndesaulniers@google.com>
Link: https://lore.kernel.org/bpf/20230615145607.3469985-1-revest@chromium.org
|
|
This reverts commit 07b679f70d73483930e8d3c293942416d9cd5c13.
This change appears to have broken things...
We now see applications hanging during disk accesses.
e.g.
multi-port virtio-blk device running in h/w (FPGA)
Host running a simple 'fio' test.
[global]
thread=1
direct=1
ioengine=libaio
norandommap=1
group_reporting=1
bs=4K
rw=read
iodepth=128
runtime=1
numjobs=4
time_based
[job0]
filename=/dev/vda
[job1]
filename=/dev/vdb
[job2]
filename=/dev/vdc
...
[job15]
filename=/dev/vdp
i.e. 16 disks; 4 queues per disk; simple burst of 4KB reads
This is repeatedly run in a loop.
After a few, normally <10 seconds, fio hangs.
With 64 queues (16 disks), failure occurs within a few seconds; with 8 queues (2 disks) it may take ~hour before hanging.
Last message:
fio-3.19
Starting 8 threads
Jobs: 1 (f=1): [_(7),R(1)][68.3%][eta 03h:11m:06s]
I think this means at the end of the run 1 queue was left incomplete.
'diskstats' (run while fio is hung) shows no outstanding transactions.
e.g.
$ cat /proc/diskstats
...
252 0 vda 1843140071 0 14745120568 712568645 0 0 0 0 0 3117947 712568645 0 0 0 0 0 0
252 16 vdb 1816291511 0 14530332088 704905623 0 0 0 0 0 3117711 704905623 0 0 0 0 0 0
...
Other stats (in the h/w, and added to the virtio-blk driver ([a]virtio_queue_rq(), [b]virtblk_handle_req(), [c]virtblk_request_done()) all agree, and show every request had a completion, and that virtblk_request_done() never gets called.
e.g.
PF= 0 vq=0 1 2 3
[a]request_count - 839416590 813148916 105586179 84988123
[b]completion1_count - 839416590 813148916 105586179 84988123
[c]completion2_count - 0 0 0 0
PF= 1 vq=0 1 2 3
[a]request_count - 823335887 812516140 104582672 75856549
[b]completion1_count - 823335887 812516140 104582672 75856549
[c]completion2_count - 0 0 0 0
i.e. the issue is after the virtio-blk driver.
This change was introduced in kernel 6.3.0.
I am seeing this using 6.3.3.
If I run with an earlier kernel (5.15), it does not occur.
If I make a simple patch to the 6.3.3 virtio-blk driver, to skip the blk_mq_add_to_batch()call, it does not fail.
e.g.
kernel 5.15 - this is OK
virtio_blk.c,virtblk_done() [irq handler]
if (likely(!blk_should_fake_timeout(req->q))) {
blk_mq_complete_request(req);
}
kernel 6.3.3 - this fails
virtio_blk.c,virtblk_handle_req() [irq handler]
if (likely(!blk_should_fake_timeout(req->q))) {
if (!blk_mq_complete_request_remote(req)) {
if (!blk_mq_add_to_batch(req, iob, virtblk_vbr_status(vbr), virtblk_complete_batch)) {
virtblk_request_done(req); //this never gets called... so blk_mq_add_to_batch() must always succeed
}
}
}
If I do, kernel 6.3.3 - this is OK
virtio_blk.c,virtblk_handle_req() [irq handler]
if (likely(!blk_should_fake_timeout(req->q))) {
if (!blk_mq_complete_request_remote(req)) {
virtblk_request_done(req); //force this here...
if (!blk_mq_add_to_batch(req, iob, virtblk_vbr_status(vbr), virtblk_complete_batch)) {
virtblk_request_done(req); //this never gets called... so blk_mq_add_to_batch() must always succeed
}
}
}
Perhaps you might like to fix/test/revert this change...
Martin
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202306090826.C1fZmdMe-lkp@intel.com/
Cc: Suwan Kim <suwan.kim027@gmail.com>
Tested-by: edliaw@google.com
Reported-by: "Roberts, Martin" <martin.roberts@intel.com>
Message-Id: <336455b4f630f329380a8f53ee8cad3868764d5c.1686295549.git.mst@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
s/ep_chg_chg_id/ep_chg_id in documentation of master clock structure.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20230615093227.576102-12-claudiu.beznea@microchip.com
|
|
Switch SAMA7G5 clocks to use parent_hw and parent_data. Having
parent_hw instead of parent names improves to clock registration
speed and re-parenting. Extra time saved on registration is
~250us when running at 800MHz.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20230615093227.576102-11-claudiu.beznea@microchip.com
|
|
Switch slow clock drivers to use parent_data and parent_hw.
With this parent-child relation is described with pointers rather
than strings.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20230615093227.576102-10-claudiu.beznea@microchip.com
|
|
Add support for parent_hw in SAM9X60 PLL clock drivers.
With this parent-child relation is described with pointers rather
than strings making registration a bit faster.
All the SoC based drivers that rely on clk-sam9x60-pll were adapted
to the new API change. The switch itself for SoCs will be done
in subsequent patches.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20230615093227.576102-9-claudiu.beznea@microchip.com
|
|
Add support for parent_hw in utmi clock drivers.
With this parent-child relation is described with pointers rather
than strings making registration a bit faster.
All the SoC based drivers that rely on clk-utmi were adapted
to the new API change. The switch itself for SoCs will be done
in subsequent patches.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20230615093227.576102-8-claudiu.beznea@microchip.com
|
|
Add support for parent_hw in system clock drivers.
With this parent-child relation is described with pointers rather
than strings making registration a bit faster.
All the SoC based drivers that rely on clk-system were adapted
to the new API change. The switch itself for SoCs will be done
in subsequent patches.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20230615093227.576102-7-claudiu.beznea@microchip.com
|
|
Add support for parent_hw in programmable clock driver.
With this parent-child relation is described with pointers rather
than strings making registration a bit faster.
All the SoC based drivers that rely on clk-programmable were adapted
to the new API change. The switch itself for SoCs will be done
in subsequent patches.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20230615093227.576102-6-claudiu.beznea@microchip.com
|
|
Add support for parent_hw in peripheral clock drivers.
With this parent-child relation is described with pointers rather
than strings making registration a bit faster.
All the SoC based drivers that rely on clk-peripheral were adapted
to the new API change. The switch itself for SoCs will be done
in subsequent patches.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20230615093227.576102-5-claudiu.beznea@microchip.com
|
|
Add support for parent_hw in master clock drivers.
With this parent-child relation is described with pointers rather
than strings making registration a bit faster.
All the SoC based drivers that rely on clk-master were adapted
to the new API change. The switch itself for SoCs will be done
in subsequent patches.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20230615093227.576102-4-claudiu.beznea@microchip.com
|
|
Add support for parent_hw in generic clock drivers.
With this parent-child relation is described with pointers rather
than strings making registration a bit faster.
All the SoC based drivers that rely on clk-generated were adapted
to the new API change. The switch itself for SoCs will be done
in subsequent patches.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20230615093227.576102-3-claudiu.beznea@microchip.com
|
|
Add support for parent_data and parent_hw in main oscillator clock drivers.
With this parent-child relations are described with pointers rather
than strings making registration a bit faster.
All the SoC based drivers that rely on clk-main were adapted
to the new API change. The switch itself for SoCs will be done
in subsequent patches.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Link: https://lore.kernel.org/r/20230615093227.576102-2-claudiu.beznea@microchip.com
|
