| Age | Commit message (Collapse) | Author |
|---|
|
The DSI host has different modes in prepare() and enable() functions,
prepare() is in LP command mode and enable() is in HS video mode.
>From our experience, generally the initialization sequence needs to be
sent in the LP command mode.
Move the setup init function from enable() to prepare() to fix a display
shift on rk3568 evb.
Tested on rk3568/rk3576/rk3588 EVB.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250618091520.691590-1-andyshrk@163.com
|
|
Although the datasheet of the panel module describes that it has a
reset pin, in the actual hardware design, we often use an RC circuit
to control the reset, and rarely use GPIO to control the reset. This
is the way it is done on our numerous development boards (such as
RK3568/RK3576 EVB).
So make the reset-gpio optional.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250616070536.670519-2-andyshrk@163.com
|
|
Although the datasheet of the panel module describes that it has a
reset pin, in the actual hardware design, we often use an RC circuit
to control the reset, and rarely use GPIO to control the reset. This
is the way it is done on our numerous development boards (such as RK3568,
RK3576 EVB).
So make the reset-gpio optional.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Acked-by: Rob Herring (Arm) <robh@kernel.org>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250616070536.670519-1-andyshrk@163.com
|
|
Add support for the 2160x1080 LCD panel from DJN (98-03057-6598B-I)
bundled with a HX83112B driver IC, as found on the Fairphone 3
smartphone.
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Luca Weiss <luca@lucaweiss.eu>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250611-fp3-display-v4-3-ef67701e7687@lucaweiss.eu
|
|
Himax HX83112B is a display driver IC used to drive LCD DSI panels.
Describe it and the Fairphone 3 panel (98-03057-6598B-I) from DJN using
it.
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luca Weiss <luca@lucaweiss.eu>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250611-fp3-display-v4-2-ef67701e7687@lucaweiss.eu
|
|
Add the vendor prefix for DJN (http://en.djnlcd.com/).
Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Luca Weiss <luca@lucaweiss.eu>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20250611-fp3-display-v4-1-ef67701e7687@lucaweiss.eu
|
|
Since the drm_mock_scheduler does not have real users in userspace, nor
does it have real hardware or firmware rings, it's not necessary to
signal timedout fences nor free jobs - from a functional standpoint.
Still, the dma_fence framework establishes the hard rule that all fences
must always get signaled.
The unit tests, moreover, should as much as possible represent the
intended usage of the scheduler API.
Furthermore, this later enables simplifying the mock scheduler's
teardown code path.
Make sure timed out hardware fences get signaled with the appropriate
error code.
Signed-off-by: Philipp Stanner <phasta@kernel.org>
Acked-by: Danilo Krummrich <dakr@kernel.org>
Link: https://lore.kernel.org/r/20250605134154.191764-2-phasta@kernel.org
|
|
Use drm dp helper to enable backlight now that it has been modified
to set PANEL_LUMINANCE_CONTROL_ENABLE bit based on if capability
supports it and the driver wants it. Remove the dead code.
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://lore.kernel.org/r/20250620063445.3603086-14-suraj.kandpal@intel.com
|
|
Now that the drm helper sets the backlight using luminance
too we can use that. Remove the obselete function.
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://lore.kernel.org/r/20250620063445.3603086-13-suraj.kandpal@intel.com
|
|
Now that drm_edp_backlight init has been modified to take
into account the setup of lumininace based brightness manipulation
we can just use that.
--v2
-Fix commit message [Arun]
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://lore.kernel.org/r/20250620063445.3603086-12-suraj.kandpal@intel.com
|
|
Add flag to enable brightness control via luminance value
when enabling edp backlight.
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://lore.kernel.org/r/20250620063445.3603086-11-suraj.kandpal@intel.com
|
|
Change the argument type to u32 for the default level being sent
since it has to now account for luminance value which has to be
set for DP_EDP_PANEL_LUMINANCE_TARGET_VALUE.
--v2
-No need to typecast [Jani]
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://lore.kernel.org/r/20250620063445.3603086-10-suraj.kandpal@intel.com
|
|
Modify drm_edp_backlight_set_level to be able to set the value
for register in DP_EDP_PANEL_TARGET_LUMINANCE_VALUE. We multiply
the level with 1000 since we get the value in Nits and the
register accepts it in milliNits.
--v2
-Add comment regarding the unit [Arun]
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://lore.kernel.org/r/20250620063445.3603086-9-suraj.kandpal@intel.com
|
|
Use u32 for level variable as one may need to pass value for
DP_EDP_PANEL_TARGET_LUMINANCE_VALUE.
--v2
-Typecase is not needed [Jani]
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://lore.kernel.org/r/20250620063445.3603086-8-suraj.kandpal@intel.com
|
|
Modify drm_edp_probe_state to read current level from
DP_EDP_PANEL_TARGET_LUMINANCE_VALUE. We divide it by
1000 since the value in this register is in millinits.
--v2
-Add comment on the unit sent back [Arun]
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://lore.kernel.org/r/20250620063445.3603086-7-suraj.kandpal@intel.com
|
|
Change the current_level argument type to u32 from u16
since it can now carry the value which it gets from
DP_EDP_PANEL_TARGET_LUMINANCE_VALUE.
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://lore.kernel.org/r/20250620063445.3603086-6-suraj.kandpal@intel.com
|
|
Use u32 instead of u16 for max variable in drm_edp_backlight_info
since it can now hold max luminance range value which is u32.
We will set this max with max_luminance value when luminance_set is
true.
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://lore.kernel.org/r/20250620063445.3603086-5-suraj.kandpal@intel.com
|
|
Add new argument to drm_edp_backlight_init which gives the
max_luminance which will be needed to set the max values for
backlight.
--v2
-Use pass only max luminance instead of luminance_range_info struct
[Arun]
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://lore.kernel.org/r/20250620063445.3603086-4-suraj.kandpal@intel.com
|
|
Add bool argument in drm_edp_backlight init to provide the drivers
option to choose if they want to use luminance values to
manipulate brightness.
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://lore.kernel.org/r/20250620063445.3603086-3-suraj.kandpal@intel.com
|
|
Introduce luminance_set flag which indicates if we can manipulate
backlight using luminance value or not which is only possible
after eDP v1.5.
Signed-off-by: Suraj Kandpal <suraj.kandpal@intel.com>
Reviewed-by: Arun R Murthy <arun.r.murthy@intel.com>
Link: https://lore.kernel.org/r/20250620063445.3603086-2-suraj.kandpal@intel.com
|
|
That is something TTM internal which is about to get dropped.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Ian Forbes <ian.forbes@broadcom.com>
Link: https://lore.kernel.org/r/20250616130726.22863-1-christian.koenig@amd.com
|
|
The following error has been reported sporadically by CI when a test
unbinds the i915 driver on a ring submission platform:
<4> [239.330153] ------------[ cut here ]------------
<4> [239.330166] i915 0000:00:02.0: [drm] drm_WARN_ON(dev_priv->mm.shrink_count)
<4> [239.330196] WARNING: CPU: 1 PID: 18570 at drivers/gpu/drm/i915/i915_gem.c:1309 i915_gem_cleanup_early+0x13e/0x150 [i915]
...
<4> [239.330640] RIP: 0010:i915_gem_cleanup_early+0x13e/0x150 [i915]
...
<4> [239.330942] Call Trace:
<4> [239.330944] <TASK>
<4> [239.330949] i915_driver_late_release+0x2b/0xa0 [i915]
<4> [239.331202] i915_driver_release+0x86/0xa0 [i915]
<4> [239.331482] devm_drm_dev_init_release+0x61/0x90
<4> [239.331494] devm_action_release+0x15/0x30
<4> [239.331504] release_nodes+0x3d/0x120
<4> [239.331517] devres_release_all+0x96/0xd0
<4> [239.331533] device_unbind_cleanup+0x12/0x80
<4> [239.331543] device_release_driver_internal+0x23a/0x280
<4> [239.331550] ? bus_find_device+0xa5/0xe0
<4> [239.331563] device_driver_detach+0x14/0x20
...
<4> [357.719679] ---[ end trace 0000000000000000 ]---
If the test also unloads the i915 module then that's followed with:
<3> [357.787478] =============================================================================
<3> [357.788006] BUG i915_vma (Tainted: G U W N ): Objects remaining on __kmem_cache_shutdown()
<3> [357.788031] -----------------------------------------------------------------------------
<3> [357.788204] Object 0xffff888109e7f480 @offset=29824
<3> [357.788670] Allocated in i915_vma_instance+0xee/0xc10 [i915] age=292729 cpu=4 pid=2244
<4> [357.788994] i915_vma_instance+0xee/0xc10 [i915]
<4> [357.789290] init_status_page+0x7b/0x420 [i915]
<4> [357.789532] intel_engines_init+0x1d8/0x980 [i915]
<4> [357.789772] intel_gt_init+0x175/0x450 [i915]
<4> [357.790014] i915_gem_init+0x113/0x340 [i915]
<4> [357.790281] i915_driver_probe+0x847/0xed0 [i915]
<4> [357.790504] i915_pci_probe+0xe6/0x220 [i915]
...
Closer analysis of CI results history has revealed a dependency of the
error on a few IGT tests, namely:
- igt@api_intel_allocator@fork-simple-stress-signal,
- igt@api_intel_allocator@two-level-inception-interruptible,
- igt@gem_linear_blits@interruptible,
- igt@prime_mmap_coherency@ioctl-errors,
which invisibly trigger the issue, then exhibited with first driver unbind
attempt.
All of the above tests perform actions which are actively interrupted with
signals. Further debugging has allowed to narrow that scope down to
DRM_IOCTL_I915_GEM_EXECBUFFER2, and ring_context_alloc(), specific to ring
submission, in particular.
If successful then that function, or its execlists or GuC submission
equivalent, is supposed to be called only once per GEM context engine,
followed by raise of a flag that prevents the function from being called
again. The function is expected to unwind its internal errors itself, so
it may be safely called once more after it returns an error.
In case of ring submission, the function first gets a reference to the
engine's legacy timeline and then allocates a VMA. If the VMA allocation
fails, e.g. when i915_vma_instance() called from inside is interrupted
with a signal, then ring_context_alloc() fails, leaving the timeline held
referenced. On next I915_GEM_EXECBUFFER2 IOCTL, another reference to the
timeline is got, and only that last one is put on successful completion.
As a consequence, the legacy timeline, with its underlying engine status
page's VMA object, is still held and not released on driver unbind.
Get the legacy timeline only after successful allocation of the context
engine's VMA.
v2: Add a note on other submission methods (Krzysztof Karas):
Both execlists and GuC submission use lrc_alloc() which seems free
from a similar issue.
Fixes: 75d0a7f31eec ("drm/i915: Lift timeline into intel_context")
Closes: https://gitlab.freedesktop.org/drm/i915/kernel/-/issues/12061
Cc: Chris Wilson <chris.p.wilson@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Krzysztof Karas <krzysztof.karas@intel.com>
Reviewed-by: Sebastian Brzezinka <sebastian.brzezinka@intel.com>
Reviewed-by: Krzysztof Niemiec <krzysztof.niemiec@intel.com>
Signed-off-by: Janusz Krzysztofik <janusz.krzysztofik@linux.intel.com>
Reviewed-by: Nitin Gote <nitin.r.gote@intel.com>
Reviewed-by: Andi Shyti <andi.shyti@linux.intel.com>
Signed-off-by: Andi Shyti <andi.shyti@linux.intel.com>
Link: https://lore.kernel.org/r/20250611104352.1014011-2-janusz.krzysztofik@linux.intel.com
|
|
As with the RK3588 SoC, RK3576 also allows the use of HDMI PHY PLL as an
alternative and more accurate pixel clock source for VOP2.
Document the optional PLL clock property.
Moreover, given that this is part of a series intended to address some
recent display problems, provide the appropriate tags to facilitate
backporting.
Fixes: c3b7c5a4d7c1 ("dt-bindings: display: vop2: Add rk3576 support")
Cc: stable@vger.kernel.org
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: "Rob Herring (Arm)" <robh@kernel.org>
Tested-by: Nicolas Frattaroli <nicolas.frattaroli@collabora.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://lore.kernel.org/r/20250612-rk3576-hdmitx-fix-v1-1-4b11007d8675@collabora.com
|
|
Currently, Ultrajoiner is supported only on Xe2_HPD.
Update the HAS_ULTRAJOINER macro to reflect the same.
v2: Clarify the commit message to specify platform. (Jani)
Bspec: 69556
Signed-off-by: Ankit Nautiyal <ankit.k.nautiyal@intel.com>
Reviewed-by: Karthik B S <karthik.b.s@intel.com>
Link: https://lore.kernel.org/r/20250611053039.377695-1-ankit.k.nautiyal@intel.com
|
|
The GitLab runner tags are case sensitive, and Flip-hatch's tag was
incorrectly lowercase. This prevented jobs from being picked up
by the runner. Fix the runner tag for Flip-hatch.
Based on https://gitlab.freedesktop.org/mesa/mesa/-/commit/03b480d3
Signed-off-by: Vignesh Raman <vignesh.raman@collabora.com>
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
|
|
These runners are no more. So remove the jobs.
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
|
|
The current s3cp stopped working after the migration. Update to the
latest mesa and ci-templates to get s3cp working again and adapt to
recent changes in mesa-ci.
Acked-by: Daniel Stone <daniels@collabora.com>
Acked-by: Helen Koike <helen.fornazier@gmail.com>
Signed-off-by: Vignesh Raman <vignesh.raman@collabora.com>
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
|
|
The python-artifacts job has a timeout of 10 minutes, which causes
build failures as it was unable to clone the repository within the
specified limits. Set GIT_DEPTH to 10 to speed up cloning and avoid
build failures due to timeouts when fetching the full repository.
Acked-by: Daniel Stone <daniels@collabora.com>
Acked-by: Helen Koike <helen.fornazier@gmail.com>
Signed-off-by: Vignesh Raman <vignesh.raman@collabora.com>
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
|
|
Back-merge drm-next to (indirectly) get arm-smmu updates for making
stall-on-fault more reliable.
Signed-off-by: Rob Clark <robin.clark@oss.qualcomm.com>
|
|
Fix Kconfig symbol dependency on KUNIT, which isn't actually required
for XE to be built-in. However, if KUNIT is enabled, it must be built-in
too.
Fixes: 08987a8b6820 ("drm/xe: Fix build with KUNIT=m")
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Thomas Hellström <thomas.hellstrom@linux.intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Harry Austen <hpausten@protonmail.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20250627-xe-kunit-v2-2-756fe5cd56cf@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
If CONFIG_DRM_XE_DISPLAY is set, the xe module can only be built as
module to avoid duplicate symbols from i915. The interface for pcode was
added without considering that, so the build breaks if both xe and i915
are built-in.
Since the intel_pcode_* functions should only be called from the display
side (xe side should call the xe interface directly) and there's already
a protection in Kconfig to avoid the problematic configuration, ifdef it
out in case CONFIG_DRM_XE_DISPLAY is disabled.
Closes: https://lore.kernel.org/r/3667a992-a24b-4e49-aab2-5ca73f2c0a56@infradead.org
Fixes: d9465cc8ac2d ("drm/xe/pcode: add struct drm_device based interface")
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://lore.kernel.org/r/20250627-xe-kunit-v2-1-756fe5cd56cf@intel.com
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
|
|
The commit d391c5827107 ("drivers/firmware: move x86 Generic System
Framebuffers support") moved the sysfb*.c source files from arch/x86
to drivers/firmware, because the logic wasn't x86 specific and could
be used by other architectures.
But the drivers/firmware path is not listed in MAINTAINERS, which led
to the files being orphaned and scripts/get_maintainer.pl not listing
a mailing list to Cc anymore.
Now that we have an entry for all the firmware-provided framebuffer code,
add the missing sysfb files to make sure correct folks and list is Cc'ed.
Fixes: d391c5827107 ("drivers/firmware: move x86 Generic System Framebuffers support")
Reported-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Closes: https://lore.kernel.org/lkml/aF53djlieUNF_-aV@smile.fi.intel.com/
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://lore.kernel.org/r/20250627113328.2703491-1-javierm@redhat.com
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
|
|
Add FourCC definitions for the 48-bit RGB/BGR formats to the
DRM/KMS uapi.
The format will be used by the Raspberry Pi PiSP Back End,
supported by a V4L2 driver in kernel space and by libcamera in
userspace, which uses the DRM FourCC identifiers.
Signed-off-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Reviewed-by: Rob Clark <robin.clark@oss.qualcomm.com>
Reviewed-by: Simon Ser <contact@emersion.fr>
Reviewed-by: Naushir Patuck <naush@raspberrypi.com>
Link: https://lore.kernel.org/r/20240226132544.82817-1-jacopo.mondi@ideasonboard.com
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
|
|
bo->size is redundant because the base GEM object already has a size
field with the same value. Drop bo->size and use the base GEM object’s
size instead. While at it, introduce xe_bo_size() to abstract the BO
size.
v2:
- Fix typo in kernel doc (Ashutosh)
- Fix kunit (CI)
- Fix line wrap (Checkpatch)
v3:
- Fix sriov build (CI)
v4:
- Fix display build (CI)
Signed-off-by: Matthew Brost <matthew.brost@intel.com>
Reviewed-by: Ashutosh Dixit <ashutosh.dixit@intel.com>
Link: https://lore.kernel.org/r/20250625144128.2827577-1-matthew.brost@intel.com
|
|
The Dynamic Inhibit Context Switch is an optimization aimed at reducing
the amount of time the HW is stuck waiting on an unsatisfied semaphore.
When this optimization is enabled, the GuC will dynamically modify the
CTX_CTRL_INHIBIT_SYN_CTX_SWITCH in the CTX_CONTEXT_CONTROL register of
LRCs to enable immediate switching out on an unsatisfied semaphore wait
when multiple contexts are competing for time on the same engine.
This feature is available on recent HW from GuC 70.40.1 onwards and it
is enabled via a per-VF feature opt-in.
v2: rebase
v3: switch to using guc_buf_cache instead of dedicated alloc
v4: add helper to check for feature availability (Michal), don't enable
if multi-lrc is possible.
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Julia Filipchuk <julia.filipchuk@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://lore.kernel.org/r/20250625205405.1653212-4-daniele.ceraolospurio@intel.com
|
|
On newer HW (Xe2 onwards + PVC) it is possible to get extra information
when a CAT error occurs, specifically a dword reporting the error type.
To enable this extra reporting, we need to opt-in with the GuC, which is
done via a specific per-VF feature opt-in H2G.
On platforms where the HW does not support the extra reporting, the GuC
will set the type to 0xdeadbeef, so we can keep the code simple and
opt-in to the feature on every platform and then just discard the data
if it is invalid.
Note that on native/PF we're guaranteed that the opt in is available
because we don't support any GuC old enough to not have it, but if we're
a VF we might be running on a non-XE PF with an older GuC, so we need to
handle that case. We can re-use the invalid type above to handle this
scenario the same way as if the feature was not supported in HW.
Given that this patch is the first user of the guc_buf_cache on native
and VF, it also extends that feature to non-PF use-cases.
v2: simpler print for the error type (John), rebase
v3: use guc_buf_cache instead of new alloc, simpler doc (Michal)
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Nirmoy Das <nirmoy.das@intel.com>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: Nirmoy Das <nirmoy.das@intel.com> #v1
Reviewed-by: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: John Harrison <John.C.Harrison@Intel.com>
Link: https://lore.kernel.org/r/20250625205405.1653212-3-daniele.ceraolospurio@intel.com
|
|
Move big-endian support from drm_fb_xrgb8888_to_rgb565() into the new
helper drm_xrgb8888_to_rgb565be(). The functionality is required for
displays with big-endian byte order. Update all callers.
With the change applied, drm_fb_xrgb8888_to_rgb565() has the same
signature as the other conversion functions, which is required for
further updates to drm_fb_blit(). Also makes the format-conversion
helper available to panic handlers, if necessary.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://lore.kernel.org/r/20250625114911.1121301-1-tzimmermann@suse.de
|
|
Add a function for dumping the entries of a specific flip queue.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250624170049.27284-9-ville.syrjala@linux.intel.com
|
|
Implement the driver side of Wa_18034343758, which is supposed to
prevent the DSB and DMC from accessing registers in parallel, and
thus potentially corrupting the registers due to a hardware issue
(which should be fixed in PTL-B0).
The w/a sequence goes as follows:
DMC starts the DSB
| \
DMC halts itself | DSB waits a while for DMC to have time to halt
. | DSB executes normally
. | DSB unhalts the DMC at the very end
. /
DMC resumes execution
v2: PTL-B0+ firmware no longer has the w/a since the hw got fixed
v3: Do the w/a on all PTL for now since we only have the A0 firmware
binaries which issues the halt instructions unconditionally
v4: PTL DMC binaries do in fact have the A0 vs. B0 split, so skip
the w/a on PTL-B0+
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250624170049.27284-7-ville.syrjala@linux.intel.com
|
|
Support commits via the flip queue (as opposed to DSB or MMIO).
As it's somewhat unknown if we can actually use it is currently
gated behind the new use_flipq modparam, which defaults to disabled.
The implementation has a bunch of limitations that would need
real though to solve:
- disabled when PSR is used
- disabled when VRR is used
- color management updates not performed via the flip queue
v2: Don't use flip queue if there is no dmc
v3: Use intel_flipq_supported()
v3: Configure PKG_C_LATENCY appropriately
Ignore INT_VECTOR if there is a real PIPEDMC interrupt
(nothing in the hw appears to clear INT_VECTOR)
v4: Leave added_wake_time=0 when flip queue isn't used, to
avoid needleslly increasing pkg_c_latency on lnl/ptl due
to Wa_22020432604. This is a bit racy though...
Use IS_DISPLAY_VER()
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250624170049.27284-6-ville.syrjala@linux.intel.com
|
|
Provide the lower level code for PIPEDMC based flip queue.
We'll use the so called semi-full flip queue mode where the
PIPEDMC will start the provided DSB on a scanline a little
ahead of the vblank. We need to program the triggering scanline
early enough so that the DSB has enough time to complete writing
all the double buffered registers before they get latched (at
start of vblank).
The firmware implements several queues:
- 3 "plane queues" which execute a single DSB per entry
- 1 "general queue" which can apparently execute 2 DSBs per entry
- 1 vestigial "fast queue" that replaced the "simple flip queue"
on ADL+, but this isn't supposed to be used due to issues.
But we only need a single plane queue really, and we won't actually
use it as a real queue because we don't allow queueing multiple commits
ahead of time. So the whole thing is perhaps useless. I suppose
there migth be some power saving benefits if we would get the flip
scheduled by userspace early and then could keep some hardware powered
off a bit longer until the DMC kicks off the flipq programming. But that
is pure speculation at this time and needs to be proven.
The code to hook up the flip queue into the actual atomic commit
path will follow later.
TODO: need to think how to do the "wait for DMC firmware load" nicely
need to think about VRR and PSR
etc.
v2: Don't write DMC_FQ_W2_PTS_CFG_SEL on pre-lnl
Don't oops at flipq init if there is no dmc
v3: Adapt to PTL+ flipq changes (different queue entry
layout, different trigger event, need VRR TG)
Use the actual CDCLK frequency
Ask the DSB code how long things are expected to take
v3: Adjust the cdclk rounding (docs are 100% vague, Windows
rounds like this)
Initialize some undocumented magic DMC variables on PTL
v4: Use PIPEDMC_FQ_STATUS for busy check (the busy bit in
PIPEDMC_FQ_CTRL is apparently gone on LNL+)
Based the preempt timeout on the max exec time
Preempt before disabling the flip queue
Order the PIPEDMC_SCANLINECMP* writes a bit more carefully
Fix some typos
v5: Try to deal with some clang-20 div-by-zero false positive (Nathan)
Add some docs (Jani)
Cc: Nathan Chancellor <nathan@kernel.org>
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
epr
Link: https://patchwork.freedesktop.org/patch/msgid/20250624170049.27284-5-ville.syrjala@linux.intel.com
|
|
Add the register definitions for a bunch of flip queue related
PIPEDMC registers.
v2: The layout of flip queue entries changed on PTL
Bump the DMC_FQ_W2_PTS_CFG_SEL bitfields sizes (Uma)
Reduce the scanlines to 21 bits for now (Uma)
v3: Also define some undocumented DMC variables we need on PTL
v3: Drop PIPEDMC_FQ_CTRL_BUSY as it seems to no longer exist
on LNL+
Fix up some typos
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250624170049.27284-4-ville.syrjala@linux.intel.com
|
|
The current PKG_C_LATENCY stuff looks busted in several ways:
- doesn't account for multiple pipes from different commits
correctly
- WM_LINETIME is in units of 0.125usec, PKG_C_LATENCY wants
units on 1 usec
- weird VRR state stuff being checked
- use of pointless RMW
Fix it all up. Note that it's still a bit unclear how all this
works, especially how the added_wake_time ties into the flipq
triggers in DMC, and how we need to sequence updates to
PKG_C_LATENCY when enabling/disabling pipes/etc. We may also
need to think what to about the WM1+ disabling and the related
PSR chicken bits when we can use PKG_C_LATENCY for early wake...
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250624170049.27284-3-ville.syrjala@linux.intel.com
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
|
|
AFAIK PKG_C_LATENCY.added_wake_time only matters for flip queue.
As long as we're not using that there's no point in adding any
extra wake time.
Reviewed-by: Uma Shankar <uma.shankar@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20250624170049.27284-2-ville.syrjala@linux.intel.com
|
|
Commit 77ba0b856225 ("drm/i915/dsi: convert vlv_dsi.[ch] to struct
intel_display") added a to_intel_display(connector) call to
vlv_dphy_param_init() but when vlv_dphy_param_init() gets called
the connector object has not been initialized yet, so this leads
to a NULL pointer deref:
BUG: kernel NULL pointer dereference, address: 000000000000000c
...
Hardware name: ASUSTeK COMPUTER INC. T100TA/T100TA, BIOS T100TA.314 08/13/2015
RIP: 0010:vlv_dsi_init+0x4e6/0x1600 [i915]
...
Call Trace:
<TASK>
? intel_step_name+0x4be8/0x5c30 [i915]
intel_setup_outputs+0x2d6/0xbd0 [i915]
intel_display_driver_probe_nogem+0x13f/0x220 [i915]
i915_driver_probe+0x3d9/0xaf0 [i915]
Use to_intel_display(&intel_dsi->base) instead to fix this.
Fixes: 77ba0b856225 ("drm/i915/dsi: convert vlv_dsi.[ch] to struct intel_display")
Signed-off-by: Hans de Goede <hansg@kernel.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20250626143317.101706-1-hansg@kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Drop the custom MHZ macro and replace it with HZ_PER_MHZ.
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20250527-samsung-dsim-v1-2-5be520d84fbb@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Turn the open-coded goto-again construct into a while loop, to make
samsung_dsim_transfer_start() a bit shorter and easier to read.
Hold the spinlock when looping back around and avoid the duplicated
list_empty() check.
Reviewed-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20250527-samsung-dsim-v1-1-5be520d84fbb@pengutronix.de
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Update header inclusions to follow IWYU (Include What You Use)
principle.
Note that kernel.h is discouraged to be included as it's written
at the top of that file.
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Thomas Zimmermann <tzimmermann@suse.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20250627103454.702606-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
|
|
When the panic handler is called, configure the psr to send the full
framebuffer to the monitor, otherwise the panic screen is only
partially visible.
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://lore.kernel.org/r/20250624091501.257661-12-jfalempe@redhat.com
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
|
|
On Alder Lake and later, it's not possible to disable tiling when DPT
is enabled.
So this commit implements 4-Tiling support, to still be able to draw
the panic screen.
Signed-off-by: Jocelyn Falempe <jfalempe@redhat.com>
Link: https://lore.kernel.org/r/20250624091501.257661-11-jfalempe@redhat.com
Signed-off-by: Maarten Lankhorst <dev@lankhorst.se>
|
