| Age | Commit message (Collapse) | Author |
|---|
|
The pad is now checked by v4l2_subdev_call_wappers
call_g_frame_interval-> check_frame_interval-> check_pad
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
From the measured hardware signal, OV5695 reset pin goes high for a
short period of time during boot-up. From the sensor specification, the
reset pin is active low and the DT binding defines the pin as active
low, which means that the values set by the driver are inverted and thus
the value requested in probe ends up high.
Fix it by changing probe to request the reset GPIO initialized to high,
which makes the initial state of the physical signal low.
In addition, DOVDD rising must occur before DVDD rising from spec., but
regulator_bulk_enable() API enables all the regulators asynchronously.
Use an explicit loops of regulator_enable() instead.
For power off sequence, it is required that DVDD falls first. Given the
bulk API does not give any guarantee about the order of regulators,
change the driver to use regulator_disable() instead.
The sensor also requires a delay between reset high and first I2C
transaction, which was assumed to be 8192 XVCLK cycles, but 1ms is
recommended by the vendor. Fix this as well.
Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
Signed-off-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
This patch adds mode table entry for capturing cropped 640x480 resolution
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
IMX219 sensor is capable for RAW8/RAW10 modes. This commit adds support
for RAW8 bayer format.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
When supporting Rpi Camera v2 Module on the RZ/G2E, found the driver had
some issues with rcar mipi-csi driver. The sensor never entered into LP-11
state.
The powerup sequence in the datasheet[1] shows the sensor entering into
LP-11 in streaming mode, so to fix this issue transitions are performed
from "streaming -> standby" in the probe() after power up.
With this commit the sensor is able to enter LP-11 mode during power up,
as expected by some CSI-2 controllers.
[1] https://publiclab.org/system/images/photos/000/023/294/original/
RASPBERRY_PI_CAMERA_V2_DATASHEET_IMX219PQH5_7.0.0_Datasheet_XXX.PDF
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Acked-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Commit 7cbeb2e1bf0c ("media: smiapp: Move definitions under driver
directory") moved the definitions in include/media/i2c/smiapp.h into other
files and removed include/media/i2c/smiapp.h.
Since then, ./scripts/get_maintainer.pl --self-test complains:
warning: no file matches F: include/media/i2c/smiapp.h
Remove MAINTAINER file entry to this removed file and while at it, update
Sakari's email address in this section.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add entry for my @iki.fi e-mail address to the mailmap.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Currently, imgu is working on 450MHz for all cases, however
in some cases (input frame less than 2048x1152), the imgu
did not need work in high frequency.
This patch make imgu work on 200MHz if the imgu input
frame is less than 2048x1152 to save power.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
While upgrading from 5.5.2 -> 5.5.6 I was surprised by:
ld: drivers/media/i2c/tvp5150.o: in function `tvp5150_probe':
tvp5150.c:(.text+0x11ac): undefined reference to
`__devm_regmap_init_i2c'
make: *** [Makefile:1078: vmlinux] Error 1
The fix was quick enough, make VIDEO_TVP5150 select REGMAP_I2C
And a quick grep showed that it was needed by more targets.
Signed-off-by: Ian Kumlien <ian.kumlien@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The return value checks in snd_pcm_plug_alloc() are covered with
snd_BUG_ON() macro that may trigger a kernel WARNING depending on the
kconfig. But since the error condition can be triggered by a weird
user space parameter passed to OSS layer, we shouldn't give the kernel
stack trace just for that. As it's a normal error condition, let's
remove snd_BUG_ON() macro usage there.
Reported-by: syzbot+2a59ee7a9831b264f45e@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200312155730.7520-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch adds compatible for SlimBus Controller on SDM845.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200312152510.12224-1-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The debug output for tvp5150_selmux() isn't really intuitive. Register
values are printed decimal formatted and the input/output driver states
are printed as enum. Even more the "normal" output enum mapps to zero so
a active output will printing output=0 and a inactive output=1.
Change this by brinting the register values hex formatted and the states
as more readable string.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The tvp5150 accepts NTSC(M,J,4.43), PAL (B,D,G,H,I,M,N) and SECAM video
data and is able to auto-detect the input signal. The auto-detection
does not work if the connector does not receive an input signal and the
tvp5150 might not be configured correctly. This misconfiguration leads
into wrong decoded video streams if the tvp5150 gets powered on before
the video signal is present.
Limit the supported sdtv standards according to the actual selected
connector to avoid a misconfiguration.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Document the optional binding to limit the possible sdtv standards on the
input connectors.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Use underlines to highlight optional and required properties. This is
quite common for all bindings. Align descriptions and start sentence
with uppercase letter. Also reword the usage of the required
endpoint properties for the output port in case BT.656 should be used.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Bring the device into a working state upon a open/close call. Currently
this involves only the interrupt enable/disable process but can be
extended in the future.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Currently the driver notifies internal subdevs if the signal is locked
or not. This information is also useful for userpace applications e.g. to
switch to another input device upon a signal lost event.
This commit adds the support for the userspace to subscribe to the
V4L2_EVENT_SOURCE_CHANGE and V4L2_EVENT_CTRL events.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
As documented in [1] the runtime-pm ops are used to set the device into
a fully 'workable' state. Therefore it can be used to enable or disable
the irqs.
[1] https://www.kernel.org/doc/html/latest/power/runtime_pm.html
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
There are several debug prints in the tvp5150_parse_dt() function, which
do not print the prefix, because the v4l2_subdev is not initialized, yet.
Initialize the v4l2_subdev before parsing the device tree to fix the
debug messages.
Signed-off-by: Michael Tretter <m.tretter@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Since commit 10d5509c8d50 ("[media] v4l2: remove g/s_crop from video ops")
the 'which' field for set/get_selection must be FORMAT_ACTIVE. There is
no way to try different selections. The patch adds a helper function to
select the correct selection memory space (sub-device file handle or
driver state) which will be set/returned.
The selection rectangle is updated if the format is FORMAT_ACTIVE and
the rectangle position and/or size differs from the current set
rectangle.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
ovl_inode_lock() is interruptible. When inode_lock() in ovl_llseek()
was replaced with ovl_inode_lock(), we did not add a check for error.
Fix this by making ovl_inode_lock() uninterruptible and change the
existing call sites to use an _interruptible variant.
Reported-by: syzbot+66a9752fa927f745385e@syzkaller.appspotmail.com
Fixes: b1f9d3858f72 ("ovl: use ovl_inode_lock in ovl_llseek()")
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
|
|
Currently a local copy of sel->r is made and adapted to the hardware
constraints. After the adaption the value is applied to the hardware but
the driver forgot to reflect the adapted value to the user space.
Drop the local copy and work directly on the requested rectangle
instead to fix this.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The TVP5150/1 decoders support different video input sources to their
AIP1A/B pins.
Possible configurations are as follows:
- Analog Composite signal connected to AIP1A.
- Analog Composite signal connected to AIP1B.
- Analog S-Video Y (luminance) and C (chrominance)
signals connected to AIP1A and AIP1B respectively.
This patch extends the device tree bindings documentation to describe
how the input connectors for these devices should be defined in a DT.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
This patch adds the of_graph support to describe the tvp input connections.
Physical the TVP5150 has three ports: AIP1A, AIP1B and YOUT. As result
of discussion [1],[2] the device-tree maps these ports 1:1. Look at the
Documentation for more information. Since the TVP5150 is a converter/bridge
the device-tree must contain at least 1-input and 1-output port. The
mc-connectors and mc-links are only created if the device-tree contains the
corresponding connector nodes. If more than one connector is available the
media_entity_operations.link_setup() callback ensures that only one
connector is active.
[1] https://www.spinics.net/lists/linux-media/msg138545.html
[2] https://www.spinics.net/lists/linux-media/msg138546.html
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Commit f7b4b54e6364 ("[media] tvp5150: add HW input connectors support")
added input signals support for the tvp5150, but the approach was found
to be incorrect so the corresponding DT binding commit 82c2ffeb217a
("[media] tvp5150: document input connectors DT bindings") was reverted.
This left the driver with an undocumented (and wrong) DT parsing logic,
so lets get rid of this code as well until the input connectors support
is implemented properly.
It's a partial revert due other patches added on top of mentioned commit
not allowing the commit to be reverted cleanly anymore. But all the code
related to the DT parsing logic and input entities creation are removed.
Suggested-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
[m.felsch@pengutronix.de: rm TVP5150_INPUT_NUM define]
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The patch adds the initial connector parsing code, so we can move from a
driver specific parsing code to a generic one. Currently only the
generic fields and the analog-connector specific fields are parsed. Parsing
the other connector specific fields can be added by a simple callbacks.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
[hverkuil-cisco@xs4all.nl: replace ; with break; in a empty case]
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Currently every driver needs to parse the connector endpoints by it self.
This is the initial work to make this generic. A generic connector has
common members and connector specific members. The common members are:
- type
- label (optional)
- links
- nr_of_links
The specific members are stored within a union, since only one of them
can be available at the time. Since this is the initial support the
patch adds only the analog-connector specific ones.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
A link is between two endpoints not between two ports to be more
precise. Add the local_id/remote_id field which stores the endpoint
reg/port property to the link. Now the link holds all necessary
information about a link.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
This helper was introduced before those helpers where awailable. Convert
it to cleanup the code and improbe readability.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Currently the driver differentiate the port number property handling for
ACPI and DT. This is wrong as because ACPI should use the "reg" val too
[1].
[1] https://patchwork.kernel.org/patch/11421985/
Fixes: ca50c197bd96 ("[media] v4l: fwnode: Support generic fwnode for parsing standardised properties")
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Since we expose the definition to the dt-bindings we need to keep those
definitions in sync. To address this the patch adds a simple cross
reference to the dt-bindings.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add defines which can be included to easily describe the supported
standard tv norms 'sdtv-standards' within the device tree.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Some connectors no matter if in- or output supports only a limited
range of sdtv standards. It doesn't matter if the hardware behind that
connector supports more than the listed formats since the users are
restriced by a label e.g. to plug only a camera into this connector
which uses the PAL format.
This patch adds the capability to describe such limitation within the
firmware. There are no format restrictions if the property isn't
present, so it's completely backward compatible.
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
from user space
When calling ccdc_data_size_max_bit() to validate data_sz in
vpfe_ccdc_validate_param(), it's treated as an enumeration ranging from
0 to 7 while essentially it's an 32 bit unsigned integer directly from
user space. This can make the return value of ccdc_data_size_max_bit()
underflow and bypass the following check.
To fix this, an additional check is added to the following if clause to
keep this enumaration variable in range. And if its value is not legal,
return -EINVAL properly.
Signed-off-by: Changming Liu <charley.ashbringer@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
After the switch to use v4l2_async_notifier_add_subdev() and
v4l2_async_notifier_cleanup(), unloading the ti_cal module would cause a
kernel oops.
This was root cause to the fact that v4l2_async_notifier_cleanup() tries
to kfree the asd pointer passed into v4l2_async_notifier_add_subdev().
In our case the asd reference was from a statically allocated struct.
So in effect v4l2_async_notifier_cleanup() was trying to free a pointer
that was not kalloc.
So here we switch to using a kzalloc struct instead of a static one.
To achieve this we re-order some of the calls to prevent asd allocation
from leaking.
Fixes: d079f94c9046 ("media: platform: Switch to v4l2_async_notifier_add_subdev")
Cc: stable@vger.kernel.org
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Previously, vpu->recv_buf and send_buf are forced cast from
void __iomem *tcm. vpu->recv_buf->share_buf is passed to
vpu_ipi_desc.handler(). It's not able to do unaligned access. Otherwise
kernel would crash due to unable to handle kernel paging request.
struct vpu_run {
u32 signaled;
char fw_ver[VPU_FW_VER_LEN];
unsigned int dec_capability;
unsigned int enc_capability;
wait_queue_head_t wq;
};
fw_ver starts at 4 byte boundary. If system enables
CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS, strscpy() will do
read_word_at_a_time(), which tries to read 8-byte: *(unsigned long *)addr
vpu_init_ipi_handler() calls strscpy(), which would lead to crash.
vpu_init_ipi_handler() and several other handlers (eg.
vpu_dec_ipi_handler) only do read access to this data, so they can be
const, and we can use memcpy_fromio() to copy the buf to another non iomem
buffer then pass to handler.
Fixes: 85709cbf1524 ("media: replace strncpy() by strscpy()")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Check for overflow in addition before checking for end-of-block-device.
Steps to reproduce:
#define _GNU_SOURCE 1
#include <sys/ioctl.h>
#include <sys/types.h>
#include <sys/stat.h>
#include <fcntl.h>
typedef unsigned long long __u64;
struct blk_zone_range {
__u64 sector;
__u64 nr_sectors;
};
#define BLKRESETZONE _IOW(0x12, 131, struct blk_zone_range)
int main(void)
{
int fd = open("/dev/nullb0", O_RDWR|O_DIRECT);
struct blk_zone_range zr = {4096, 0xfffffffffffff000ULL};
ioctl(fd, BLKRESETZONE, &zr);
return 0;
}
BUG: KASAN: null-ptr-deref in submit_bio_wait+0x74/0xe0
Write of size 8 at addr 0000000000000040 by task a.out/1590
CPU: 8 PID: 1590 Comm: a.out Not tainted 5.6.0-rc1-00019-g359c92c02bfa #2
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS ?-20190711_202441-buildvm-armv7-10.arm.fedoraproject.org-2.fc31 04/01/2014
Call Trace:
dump_stack+0x76/0xa0
__kasan_report.cold+0x5/0x3e
kasan_report+0xe/0x20
submit_bio_wait+0x74/0xe0
blkdev_zone_mgmt+0x26f/0x2a0
blkdev_zone_mgmt_ioctl+0x14b/0x1b0
blkdev_ioctl+0xb28/0xe60
block_ioctl+0x69/0x80
ksys_ioctl+0x3af/0xa50
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alexey Dobriyan (SK hynix) <adobriyan@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Steps to reproduce:
BLKRESETZONE zone 0
// force EIO
pwrite(fd, buf, 4096, 4096);
[issue more IO including zone ioctls]
It will start failing randomly including IO to unrelated zones because of
->error "reuse". Trigger can be partition detection as well if test is not
run immediately which is even more entertaining.
The fix is of course to clear ->error where necessary.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Alexey Dobriyan (SK hynix) <adobriyan@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The platform_get_resource_byname() function returns NULL on error, it
doesn't return error pointers.
Fixes: d166a73503ef ("spi: fspi: dynamically alloc AHB memory")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20200312113154.GC20562@mwanda
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Correct maxnode parameter value passed to mbind() syscall to be the
amount of node mask bits to analyze plus 1. Dynamically allocate node
mask memory depending on the index of node of cpu being profiled.
Fixes: c44a8b44ca9f ("perf record: Bind the AIO user space buffers to nodes")
Signed-off-by: Alexey Budankov <alexey.budankov@linux.intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Link: http://lore.kernel.org/lkml/c7ea8ffe-1357-bf9e-3a89-1da1d8e9b75b@linux.intel.com
[ Remove leftover nr_bits + 1 comment in mbind() call ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
No users, drop it.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Weiping Zhang <zhangweiping@didiglobal.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
In commit 2da22da5734 (nbd: fix zero cmd timeout handling v2),
it is allowed to reset timer when it fires if tag_set.timeout
is set to zero. If the server is shutdown and a new socket
is reconfigured, the request should be requeued to be processed by
new server instead of waiting for response from the old one.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Hou Pu <houpu@bytedance.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This patch changes the check condition for the validity/authentication
of the session.
1. The Host Session Number(HSN) in the response should match the HSN for
the session.
2. The TPER Session Number(TSN) can never be less than 4096 for a regular
session.
Reference:
Section 3.2.2.1 of https://trustedcomputinggroup.org/wp-content/uploads/TCG_Storage_Opal_SSC_Application_Note_1-00_1-00-Final.pdf
Section 3.3.7.1.1 of https://trustedcomputinggroup.org/wp-content/uploads/TCG_Storage_Architecture_Core_Spec_v2.01_r1.00.pdf
Co-developed-by: Andrzej Jakowski <andrzej.jakowski@linux.intel.com>
Signed-off-by: Andrzej Jakowski <andrzej.jakowski@linux.intel.com>
Signed-off-by: Revanth Rajashekar <revanth.rajashekar@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Nbd server with multiple connections could be upgraded since
560bc4b (nbd: handle dead connections). But if only one conncection
is configured, after we take down nbd server, all inflight IO
would finally timeout and return error. We could requeue them
like what we do with multiple connections and wait for new socket
in submit path.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Hou Pu <houpu@bytedance.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit b72053072c0b ("block: allow partitions on host aware zone
devices") introduced the helper function disk_has_partitions() to check
if a given disk has valid partitions. However, since this function result
directly depends on the disk partition table length rather than the
actual existence of valid partitions in the table, it returns true even
after all partitions are removed from the disk. For host aware zoned
block devices, this results in zone management support to be kept
disabled even after removing all partitions.
Fix this by changing disk_has_partitions() to walk through the partition
table entries and return true if and only if a valid non-zero size
partition is found.
Fixes: b72053072c0b ("block: allow partitions on host aware zone devices")
Cc: stable@vger.kernel.org # 5.5
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Reviewed-by: Johannes Thumshirn <johannes.thumshirn@wdc.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Deduplicate cancellation parts, as many of them looks the same, as do
e.g.
- io_wqe_cancel_cb_work() and io_wqe_cancel_work()
- io_wq_worker_cancel() and io_work_cancel()
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
We deleted last_md_mark_dirty long ago, this function no longer needs to
exist, delete it, otherwise a compilation error will occur when DEBUG is
opened.
Fixes: ac0acb9e39ac ("drbd: use drbd_device_post_work() in more place")
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The kernel documentation includes a brief section about genhd
capabilities, but it turns out that the only documented
capability (GENHD_FL_MEDIA_CHANGE_NOTIFY) isn't used any more.
This patch removes that flag, and documents the rest, based on my
understanding of the current uses of these flags in the kernel. The
documentation is kept in the header file, alongside the declarations,
in the hope that it will be kept up-to-date in future; the kernel
documentation is changed to include the documentation generated from
the header file.
Because the ultimate goal is to provide some end-user
documentation (or end-administrator documentation), the comments are
perhaps more user-oriented than might be expected. Since the values
are shown to users in hexadecimal, the documentation lists them in
hexadecimal, and the constant declarations are adjusted to match.
Reviewed-by: Matthew Wilcox (Oracle) <willy@infradead.org>
Signed-off-by: Stephen Kitt <steve@sk2.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Loongson 7A1000 SATA controller uses BAR0 as the base address register.
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
