| Age | Commit message (Collapse) | Author |
|---|
|
Upcoming Intel platforms use LPSS SPI_CS_CONTROL register bits 15:12 for
configuring the chip select polarities. Touch only chip select SW mode and
state bits when enabling the software chip select control in order to not
clear any other bits in the register.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Andy noticed numeric unique device ID is unsigned integer so convert it
using kstrtouint(). Actually integer in ACPI 2.0 and later is 64 bits
litte-endian unsigned integer but quite certainly having so big value here
would mean something extra than just the SPI bus number so it won't hurt to
assume only lower 32 bits carry the bus number for now.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since we call pxa2xx_ssp_get_clk_div() from pump_transfers() we may derive
pointer to struct chip_data from struct drv_data like it's done in the rest
of the functions. This will make it less errorprone.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The speed can be changed from transfer to transfer, that's why the messages
do not depict the actual values during ->setup(). Move debug messages from
->setup() to pump_transfers(). Get rid of leftovers as well.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The rate constraints in this driver are shared between all device
instances. It should not be (and is not) modified at runtime, so make them
const.
While we are at it also change the type of the rates array from u32 to
unsigned int. While both resolve to the same type, u32 is usually used to
empathize that the value is for a 32-bit hardware register or similar which
makes it slightly confusing in this context.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The rate constraints in this board driver are not modified at runtime, so
make them const.
While we are at it also remove the unnecessary 0 initializer for the mask
field.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The rate constraints in this board driver are not modified at runtime, so
make them const.
While we are at it also remove the unnecessary 0 initializer for the mask
field.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
'asoc/fix/wm8904' and 'asoc/fix/wm8962' into asoc-linus
|
|
|
|
The perf_config() infrastructure we inherited from git calls die() when
the provided config callback returns -1, meaning some key in a config
section is unexpected, that seems ok for a stdio based tool, but in
--tui we end up messing up the output, so just tell the user about the
error, wait for a keystroke and return 0, being more resilient and
proceeding with what we managed to parse.
That die() needs to die, tho :-)
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-pqtsffh2kwr5mwm4qg9kgotu@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Besides being a coding style issue, it confuses make tags:
ctags: Warning: include/kvm/arm_vgic.h:307: null expansion of name pattern "\1"
ctags: Warning: include/kvm/arm_vgic.h:308: null expansion of name pattern "\1"
ctags: Warning: include/kvm/arm_vgic.h:309: null expansion of name pattern "\1"
ctags: Warning: include/kvm/arm_vgic.h:317: null expansion of name pattern "\1"
Cc: kvmarm@lists.cs.columbia.edu
Signed-off-by: Michal Marek <mmarek@suse.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
If we panic in hyp mode, we inject a call to panic() into the EL1N host
kernel. If a guest context is active, we first attempt to restore the
minimal amount of state necessary to execute the host kernel with
restore_sysregs.
However, the SP is restored as part of restore_common_regs, and so we
may return to the host's panic() function with the SP of the guest. Any
calculations based on the SP will be bogus, and any attempt to access
the stack will result in recursive data aborts.
When running Linux as a guest, the guest's EL1N SP is like to be some
valid kernel address. In this case, the host kernel may use that region
as a stack for panic(), corrupting it in the process.
Avoid the problem by restoring the host SP prior to returning to the
host. To prevent misleading backtraces in the host, the FP is zeroed at
the same time. We don't need any of the other "common" registers in
order to panic successfully.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Cc: Christoffer Dall <christoffer.dall@linaro.org>
Cc: <kvmarm@lists.cs.columbia.edu>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
The VGIC and timer code for KVM arm/arm64 doesn't have any tracepoints
or tracepoint infrastructure defined. Rewriting some of the timer code
handling showed me how much we need this, so let's add these simple
trace points once and for all and we can easily expand with additional
trace points in these files as we go along.
Cc: Wei Huang <wei@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
The ARM architecture only saves the exit class to the HSR (ESR_EL2 for
arm64) on synchronous exceptions, not on asynchronous exceptions like an
IRQ. However, we only report the exception class on kvm_exit, which is
confusing because an IRQ looks like it exited at some PC with the same
reason as the previous exit. Add a lookup table for the exception index
and prepend the kvm_exit tracepoint text with the exception type to
clarify this situation.
Also resolve the exception class (EC) to a human-friendly text version
so the trace output becomes immediately usable for debugging this code.
Cc: Wei Huang <wei@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
Correct some old mistakes in the API documentation:
1. VCPU is identified by index (using kvm_get_vcpu() function), but
"cpu id" can be mistaken for affinity ID.
2. Some error codes are wrong.
[ Slightly tweaked some grammer and did some s/CPU index/vcpu_index/
in the descriptions. -Christoffer ]
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
We introduce kvm_arm_halt_guest and resume functions. They
will be used for IRQ forward state change.
Halt is synchronous and prevents the guest from being re-entered.
We use the same mechanism put in place for PSCI former pause,
now renamed power_off. A new flag is introduced in arch vcpu state,
pause, only meant to be used by those functions.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
In case a vcpu off PSCI call is called just after we executed the
vcpu_sleep check, we can enter the guest although power_off
is set. Let's check the power_off state in the critical section,
just before entering the guest.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reported-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
kvm_arch_vcpu_runnable now also checks whether the power_off
flag is set.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
The kvm_vcpu_arch pause field is renamed into power_off to prepare
for the introduction of a new pause field. Also vcpu_pause is renamed
into vcpu_sleep since we will sleep until both power_off and pause are
false.
Signed-off-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
vhost drivers provide guest VMs with better I/O performance and lower
CPU utilization. This patch allows users to select vhost devices under
KVM configuration menu on ARM. This makes vhost support on arm/arm64
on a par with other architectures (e.g. x86, ppc).
Signed-off-by: Wei Huang <wei@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
We mark edge-triggered interrupts with the HW bit set as queued to
prevent the VGIC code from injecting LRs with both the Active and
Pending bits set at the same time while also setting the HW bit,
because the hardware does not support this.
However, this means that we must also clear the queued flag when we sync
back a LR where the state on the physical distributor went from active
to inactive because the guest deactivated the interrupt. At this point
we must also check if the interrupt is pending on the distributor, and
tell the VGIC to queue it again if it is.
Since these actions on the sync path are extremely close to those for
level-triggered interrupts, rename process_level_irq to
process_queued_irq, allowing it to cater for both cases.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
The arch timer currently uses edge-triggered semantics in the sense that
the line is never sampled by the vgic and lowering the line from the
timer to the vgic doesn't have any effect on the pending state of
virtual interrupts in the vgic. This means that we do not support a
guest with the otherwise valid behavior of (1) disable interrupts (2)
enable the timer (3) disable the timer (4) enable interrupts. Such a
guest would validly not expect to see any interrupts on real hardware,
but will see interrupts on KVM.
This patch fixes this shortcoming through the following series of
changes.
First, we change the flow of the timer/vgic sync/flush operations. Now
the timer is always flushed/synced before the vgic, because the vgic
samples the state of the timer output. This has the implication that we
move the timer operations in to non-preempible sections, but that is
fine after the previous commit getting rid of hrtimer schedules on every
entry/exit.
Second, we change the internal behavior of the timer, letting the timer
keep track of its previous output state, and only lower/raise the line
to the vgic when the state changes. Note that in theory this could have
been accomplished more simply by signalling the vgic every time the
state *potentially* changed, but we don't want to be hitting the vgic
more often than necessary.
Third, we get rid of the use of the map->active field in the vgic and
instead simply set the interrupt as active on the physical distributor
whenever the input to the GIC is asserted and conversely clear the
physical active state when the input to the GIC is deasserted.
Fourth, and finally, we now initialize the timer PPIs (and all the other
unused PPIs for now), to be level-triggered, and modify the sync code to
sample the line state on HW sync and re-inject a new interrupt if it is
still pending at that time.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
Forwarded physical interrupts on arm/arm64 is a tricky concept and the
way we deal with them is not apparently easy to understand by reading
various specs.
Therefore, add a proper documentation file explaining the flow and
rationale of the behavior of the vgic.
Some of this text was contributed by Marc Zyngier and edited by me.
Omissions and errors are all mine.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
We currently initialize the SGIs to be enabled in the VGIC code, but we
use the VGIC_NR_PPIS define for this purpose, instead of the the more
natural VGIC_NR_SGIS. Change this slightly confusing use of the
defines.
Note: This should have no functional change, as both names are defined
to the number 16.
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
The GICD_ICFGR allows the bits for the SGIs and PPIs to be read only.
We currently simulate this behavior by writing a hardcoded value to the
register for the SGIs and PPIs on every write of these bits to the
register (ignoring what the guest actually wrote), and by writing the
same value as the reset value to the register.
This is a bit counter-intuitive, as the register is RO for these bits,
and we can just implement it that way, allowing us to control the value
of the bits purely in the reset code.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
Currently vgic_process_maintenance() processes dealing with a completed
level-triggered interrupt directly, but we are soon going to reuse this
logic for level-triggered mapped interrupts with the HW bit set, so
move this logic into a separate static function.
Probably the most scary part of this commit is convincing yourself that
the current flow is safe compared to the old one. In the following I
try to list the changes and why they are harmless:
Move vgic_irq_clear_queued after kvm_notify_acked_irq:
Harmless because the only potential effect of clearing the queued
flag wrt. kvm_set_irq is that vgic_update_irq_pending does not set
the pending bit on the emulated CPU interface or in the
pending_on_cpu bitmask if the function is called with level=1.
However, the point of kvm_notify_acked_irq is to call kvm_set_irq
with level=0, and we set the queued flag again in
__kvm_vgic_sync_hwstate later on if the level is stil high.
Move vgic_set_lr before kvm_notify_acked_irq:
Also, harmless because the LR are cpu-local operations and
kvm_notify_acked only affects the dist
Move vgic_dist_irq_clear_soft_pend after kvm_notify_acked_irq:
Also harmless, because now we check the level state in the
clear_soft_pend function and lower the pending bits if the level is
low.
Reviewed-by: Eric Auger <eric.auger@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
We currently schedule a soft timer every time we exit the guest if the
timer did not expire while running the guest. This is really not
necessary, because the only work we do in the timer work function is to
kick the vcpu.
Kicking the vcpu does two things:
(1) If the vpcu thread is on a waitqueue, make it runnable and remove it
from the waitqueue.
(2) If the vcpu is running on a different physical CPU from the one
doing the kick, it sends a reschedule IPI.
The second case cannot happen, because the soft timer is only ever
scheduled when the vcpu is not running. The first case is only relevant
when the vcpu thread is on a waitqueue, which is only the case when the
vcpu thread has called kvm_vcpu_block().
Therefore, we only need to make sure a timer is scheduled for
kvm_vcpu_block(), which we do by encapsulating all calls to
kvm_vcpu_block() with kvm_timer_{un}schedule calls.
Additionally, we only schedule a soft timer if the timer is enabled and
unmasked, since it is useless otherwise.
Note that theoretically userspace can use the SET_ONE_REG interface to
change registers that should cause the timer to fire, even if the vcpu
is blocked without a scheduled timer, but this case was not supported
before this patch and we leave it for future work for now.
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
Some times it is useful for architecture implementations of KVM to know
when the VCPU thread is about to block or when it comes back from
blocking (arm/arm64 needs to know this to properly implement timers, for
example).
Therefore provide a generic architecture callback function in line with
what we do elsewhere for KVM generic-arch interactions.
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
|
|
The PAGES_TO_MiB macro is used for unit conversion but the
trace_mc_event() tracepoint expects a page address. Fix that.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/1445341538-24271-1-git-send-email-tanxiaojun@huawei.com
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
Now, ftrace only calculate the dyn_ftrace number in the adding
breakpoint loop, not in adding update and finish update loop.
Calculate the correct dyn_ftrace, once ftrace reports the failure message
to the userspace.
Link: http://lkml.kernel.org/r/1442420382-13130-1-git-send-email-mnfhuang@gmail.com
Signed-off-by: Minfei Huang <mnfhuang@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
I.e. we want to tell the user about errors found during, for instance,
the ui_browser initialization, so that a call to ui__warning() appears
as a window waiting for a key to be pressed.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-ederrwizcl6mfz10vfobl5qq@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The annotate__configs should be sorted so that it can use bsearch(3).
However commit 0c4a5bcea460 ("perf annotate: Display total number of
samples with --show-total-period") added a new config item at the end.
This resulted in the 'annotate.use_offset' config variable cannot be
found and perf terminated like below:
$ perf report
bad config file line 6 in ~/.perfconfig
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Martin Liška <mliska@suse.cz>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Taeung Song <treeze.taeung@gmail.com>
Fixes: 0c4a5bcea460 ("perf annotate: Display total number of samples with --show-total-period")
Link: http://lkml.kernel.org/r/1445396240-3428-1-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The --call-graph option is complex so we should provide better guide for
users. Also change help message to be consistent with config option
names. Now perf top will show help like below:
$ perf top --call-graph
Error: option `call-graph' requires a value
Usage: perf top [<options>]
--call-graph <record_mode[,record_size],print_type,threshold[,print_limit],order,sort_key[,branch]>
setup and enables call-graph (stack chain/backtrace):
record_mode: call graph recording mode (fp|dwarf|lbr)
record_size: if record_mode is 'dwarf', max size of stack recording (<bytes>)
default: 8192 (bytes)
print_type: call graph printing style (graph|flat|fractal|none)
threshold: minimum call graph inclusion threshold (<percent>)
print_limit: maximum number of call graph entry (<number>)
order: call graph order (caller|callee)
sort_key: call graph sort key (function|address)
branch: include last branch info to call graph (branch)
Default: fp,graph,0.5,caller,function
Requested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Chandler Carruth <chandlerc@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1445524112-5201-2-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
All callers use locks_lock_inode_wait() instead.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
|
|
Instead of having users check for FL_POSIX or FL_FLOCK to call the correct
locks API function, use the check within locks_lock_inode_wait(). This
allows for some later cleanup.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
|
|
Users of the locks API commonly call either posix_lock_file_wait() or
flock_lock_file_wait() depending upon the lock type. Add a new function
locks_lock_inode_wait() which will check and call the correct function for
the type of lock passed in.
Signed-off-by: Benjamin Coddington <bcodding@redhat.com>
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
|
|
Fix an obvious "Broadcom Corporation" typo in a header comment.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Ray Jui <rjui@broadcom.com>
|
|
The caller callchain order is useful with --children option since it can
show 'overview' style output, but other commands which don't use
--children feature like 'perf script' or even 'perf report/top' without
--children are better to keep callee order.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Brendan Gregg <brendan.d.gregg@gmail.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Chandler Carruth <chandlerc@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1445499946-29817-1-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Currently 'perf top --call-graph' option is same as 'perf record'. But
'perf top' also need to receive display options in 'perf report'. To do
that, change parse_callchain_report_opt() to allow record options too.
Now perf top can receive display options like below:
$ perf top --call-graph
Error: option `call-graph' requires a value
Usage: perf top [<options>]
--call-graph
<mode[,dump_size],output_type,min_percent[,print_limit],call_order[,branch]>
setup and enables call-graph (stack chain/backtrace)
recording: fp dwarf lbr, output_type (graph, flat,
fractal, or none), min percent threshold, optional
print limit, callchain order, key (function or
address), add branches
$ perf top --call-graph callee,graph,fp
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Chandler Carruth <chandlerc@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1445495330-25416-2-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
These messages will be used by 'perf top' in the next patch.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Chandler Carruth <chandlerc@gmail.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/1445495330-25416-1-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Commits such as 65dd297ac25565 ("xfs: %pF is only for function
pointers") caused a regression because pretty_print() didn't support
%ps/%pS. The current %pf/%pF implementation in pretty_print() is what
%ps/%pS is supposed to do, so use the same code for %ps/%pS.
Addressing the incorrect %pf/%pF implementation is beyond the scope of
this patch.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Cc: Dave Chinner <david@fromorbit.com>
Link: http://lkml.kernel.org/r/20150831211637.GA12848@home.buserror.net
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
This patch changes return type of pstore_is_mounted from int to bool.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
|
|
Device stopped to tuning some channels after regmap conversion.
Reason is that regmap_update_bits() works a bit differently for
partially volatile registers than old homemade routine. Return
back to old routine in order to fix issue.
Fixes: 478932b16052f5ded74685d096ae920cd17d6424
Cc: <stable@kernel.org> # 4.2+
Reported-by: Mark Clarkstone <hello@markclarkstone.co.uk>
Tested-by: Mark Clarkstone <hello@markclarkstone.co.uk>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Add lock to prevent concurrent access for control message as control
message function uses shared buffer. Without the lock there may be
remote control polling which messes the buffer causing IO errors.
Increase buffer size and add check for maximum supported message
length.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=103391
Fixes: c56222a6b25c ("[media] rtl28xxu: move usb buffers to state")
Cc: <stable@vger.kernel.org> # 4.0+
Signed-off-by: Antti Palosaari <crope@iki.fi>
|
|
Fixes the following randconfig problem:
drivers/built-in.o: In function `v4l2_flash_release':
(.text+0x12204f): undefined reference to `v4l2_async_unregister_subdev'
drivers/built-in.o: In function `v4l2_flash_release':
(.text+0x122057): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o: In function `v4l2_flash_close':
v4l2-flash-led-class.c:(.text+0x12208f): undefined reference to `v4l2_fh_is_singular'
v4l2-flash-led-class.c:(.text+0x1220c8): undefined reference to `__v4l2_ctrl_s_ctrl'
drivers/built-in.o: In function `v4l2_flash_open':
v4l2-flash-led-class.c:(.text+0x12227f): undefined reference to `v4l2_fh_is_singular'
drivers/built-in.o: In function `v4l2_flash_init_controls':
v4l2-flash-led-class.c:(.text+0x12274e): undefined reference to `v4l2_ctrl_handler_init_class'
v4l2-flash-led-class.c:(.text+0x122797): undefined reference to `v4l2_ctrl_new_std_menu'
v4l2-flash-led-class.c:(.text+0x1227e0): undefined reference to `v4l2_ctrl_new_std'
v4l2-flash-led-class.c:(.text+0x122826): undefined reference to `v4l2_ctrl_handler_setup'
v4l2-flash-led-class.c:(.text+0x122839): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o: In function `v4l2_flash_init':
(.text+0x1228e2): undefined reference to `v4l2_subdev_init'
drivers/built-in.o: In function `v4l2_flash_init':
(.text+0x12293b): undefined reference to `v4l2_async_register_subdev'
drivers/built-in.o: In function `v4l2_flash_init':
(.text+0x122949): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o:(.rodata+0x20ef8): undefined reference to `v4l2_subdev_queryctrl'
drivers/built-in.o:(.rodata+0x20f10): undefined reference to `v4l2_subdev_querymenu'
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
|
|
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
When reading the firmware and sending commands, the length must
be bounds checked to avoid overrunning the size of the command
buffer and smashing the stack if the firmware is not in the expected
format:
si2168 11-0064: found a 'Silicon Labs Si2168-B40'
si2168 11-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
si2168 11-0064: firmware download failed -95
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: ffffffffa085708f
Add the proper check.
Cc: stable@kernel.org
Reported-by: Stuart Auchterlonie <sauchter@redhat.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
When reading the firmware and sending commands, the length
must be bounds checked to avoid overrunning the size of the command
buffer and smashing the stack if the firmware is not in the
expected format. Add the proper check.
Cc: stable@kernel.org
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This driver doesn't claim the IR transmitter to be wakeup source. It
even disables the clock and the IR during suspend-resume cycle.
This patch removes yet another misuse of IRQF_NO_SUSPEND.
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Guoxiong Yan <yanguoxiong@huawei.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The variable err was never initialized, that means we had been checking
a garbage value in the for loop. Moreover if the segment is not outside
the firmware file then also we have been returning the garbage.
Initialize it to 0 so that on success we return the value and no need to
check in the for loop also as it is initially 0 and whenever that value
changes we have done a break from the loop.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
