| Age | Commit message (Collapse) | Author |
|---|
|
The ColdFire 532x CPU register definitions for the multi-function setup
pins are inconsistently defined compared with other ColdFire parts. Modify
the register defintions to be just the addresses, not pointers. This also
fixes the erroneous use in one case of using these values in the UART setup
code for the 532x.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
There are a lot of unused and uneccessary definitions in the header to
support the ColdFire 532x CPU family. Remove the junk.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Currently the setup code for the FEC multi-function pins on the ColdFire 528x
has the addresses hard coded in the code. Use the register defines that
already exist for this.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Remove the last address definitions relative to the IPSBAR peripheral region
for the ColdFire 527x family. This involved cleaning up some magic numbers
used in the code part, and making them proper register definitions in the 527x
specific header.
This is part of the process of cleaning up the ColdFire register definitions
to make them consistently use absolute addresses for the primary registers.
This will reduce the occasional bugs caused by inconsistent definition of
the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
There is a bunch of old unused and ugly register definitions in the ColdFire
5282 header. Remove them.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
The registers used to configure and set the multifunction pins on the 5272
ColdFire are defined as absolute addresses. So the use of them does not need
to be offset relative to the peripheral region address.
Fix two cases of incorrect usage of these addresses. Both affect UART
initialization, one in the common UART pin setup code, the other in the
NETtel board specific UART signal handling.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Make the ColdFire 5249 MBAR peripheral register definitions absolute
addresses, instead of offsets into the region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Make the remaining definitions of the 5272 ColdFire registers absolute
addresses. Currently some are relative to the MBAR peripheral region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
addresses
Make all definitions of the ColdFire MPARK and IRQ Assignment registers
absolute addresses. Currently some are relative to the MBAR peripheral
region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Make all definitions of the ColdFire Chip Select registers absolute addresses.
Currently some are relative to the MBAR peripheral region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
addresses
Make all definitions of the ColdFire Interrupt Source registers absolute
addresses. Currently some are relative to the MBAR peripheral region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Make all definitions of the ColdFire Pin Assignment registers absolute
addresses. Currently some are relative to the MBAR peripheral region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Make all definitions of the ColdFire Software watchdog registers absolute
addresses. Currently some are relative to the MBAR peripheral region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Make all definitions of the ColdFire Reset and System registers absolute
addresses. Currently some are relative to the MBAR peripheral region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the abolsute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
Make all definitions of the ColdFire Interrupt Mask and Pending registers
absolute addresses. Currently some are relative to the MBAR peripheral region.
The various ColdFire parts use different methods to address the internal
registers, some are absolute, some are relative to peripheral regions
which can be mapped at different address ranges (such as the MBAR and IPSBAR
registers). We don't want to deal with this in the code when we are
accessing these registers, so make all register definitions the absolute
address - factoring out whether it is an offset into a peripheral region.
This makes them all consistently defined, and reduces the occasional bugs
caused by inconsistent definition of the register addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
When ext4_bread() returns NULL and err is set to zero, this means
there is no phyical block mapped to the specified logical block
number. (Previous to commit 90b0a97323, err was uninitialized in this
case, which caused other problems.)
The directory handling routines use ext4_bread() in many places, the
fact that ext4_bread() now returns NULL with err set to zero could
cause problems since a number of these functions will simply return
the value of err if the result of ext4_bread() was the NULL pointer,
causing the caller of the function to think that the function was
successful.
Since directories should never contain holes, this case can only
happen if the file system is corrupted. This commit audits all of the
callers of ext4_bread(), and makes sure they do the right thing if a
hole in a directory is found by ext4_bread().
Some ext4_bread() callers did not need any changes either because they
already had its own hole detector paths.
Signed-off-by: Carlos Maiolino <cmaiolino@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
|
As discussed at the Plumber's Conference, reserve the bit 0x04 in
fallocate() to prevent collisions with a commonly used out-of-tree
patch which implements the no-hide-stale feature.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
|
Let the compiler choose which register to use in the cache flushing
asm statements, instead of imposing %d0.
Additionally, fix two typo's.
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
DRAGEN2 should obviously be CONFIG_DRAGEN2, but the screen.h entry it
triggers only references files that are nowhere to be found in the
current tree. Besides, nothing uses screen.h. So just drop all that.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
|
|
IFC-1.1.0 uses 28nm techenology for SRAM. This tech has known limitaion for
SRAM i.e. "byte select" is not supported. Hence Read Modify Write is
implemented in IFC for any "system side write" into sram buffer. Reading an
uninitialized memory results in ECC Error from sram wrapper.
Hence we must initialize/prefill SRAM buffer by any data before writing
anything in SRAM from system side. To initialize SRAM user can use "READID"
NAND command with read bytes equal to SRAM size. It will be a one time
activity post boot.
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The original code uses 'Programming Interface' field to judge if PCIE is
EP or RC mode, however, some latest silicons do not support this
functionality. According to PCIE specification, 'Header Type' offset 0x0e
is used to indicate header type, so change code to use 'Header Type' field
to judge PCIE mode. Because FSL PCI controller does not support
'Header Type', patch still uses 'Programming Interface' to identify PCI
mode.
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
In the check code above, if orig_start != donor_start, we would
return -EINVAL. So here, orig_start should be equal with donor_start.
Remove the redundant check here.
Signed-off-by: Wang Sheng-Hui <shhuiw@gmail.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
|
|
'pindesc' was not freed when returning from an error induced
exit path.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This named the sleep mode pin configurations as *slpm* rather
than *sleep* to correspond better with the settings from the
datasheet. It also defines an optional sleep mode for the SPI
controller SPI2.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The use of regsets has removed the need for many private ptrace requests,
so remove the corresponding definitions from the user-visible ptrace.h
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Convert the struct i2c_msg initialization to C99 format. This makes
maintaining and editing the code simpler. Also helps once other fields
like transferred are added in future.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
KPROBE_TRACING has been replaced by KPROBE_EVENT.
Signed-off-by: Liu Bo <liub.liubo@gmail.com>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
wlcore_op_set_key() calls wl18xx_set_key(),
which in turn executes some of his function
calls without acquiring wl->mutex and making
sure the fw is awake.
Adding mutex_lock()/ps_elp_wakeup() calls is
not enough, as wl18xx_set_key() calls
wl1271_tx_flush() which can't be called while
the mutex is taken.
Add the required calls to wlcore_op_set_key,
but limit the queues_stop and flushing
to the only encryption types in which
a spare block might be needed (GEM and TKIP).
[Arik - move state != ON check]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
|
|
The current elp timeout (the same as the dynamic
ps timeout - 1500ms) is too high. Usually,
wl1271_ps_elp_sleep() get called right after tx/rx,
which is fine, but some command might get sent
even when there is no traffic (e.g. ht changes
triggered by beacon frames), and leaving the
device awake for 1500ms in this case is redundant.
Use a timeout of 30ms.
The fw won't enter elp anyway before the dynamic-ps
timeout was expired as well (and it entered ps
successfully).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
|
|
The NVS file is loaded by the device's probe callback with the help of
request_firmware(). Since request_firmware() relies on udevd, the
modules cannot be loaded before hotplug events are handled.
Fix this by loading the NVS file asynchronously and continue
initialization only after the firmware request is over.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
|
|
Move most of the device-specific probe functionality into setup(), a new
op. By doing this, wlcore_probe will be the first to request a firmware
from userspace, making it easier to load the NVS file asynchronously.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
|
|
When the no_recovery flag is used, the recovery work will not restart
the FW and the state will not be set to 'on'. To enable post-mortem
analysis, allow memory access in the 'restarting' state.
Also, since the FW might not be operational, don't fail the read/write
operations if elp_wakeup fails.
Reported-by: Arkady Miasnikov <a-miasnikov@ti.com>
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
|
|
Currently, all the (station) roles use the same
keep-alive template id (0). However, the klv
template ids shouldn't be shared by different
roles.
Implement a simple klv_templates bitmap, and let
each role allocate its own klv template id on
role initialization.
[Arik - remove invalidation of KLV template when getting into "idle".
This is already handled in unjoin]
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
|
|
Previously, invalidation of the keep-alive template was
done when going idle. However, while removing the
idle-handling we didn't move the keep-alive template
invalidation to another place.
This finally resulted in fw error when trying to use
the keep-alive template by another role.
(Note that we still have an error here - each role
should have its unique keep-alive template id, while
currently they all use CMD_TEMPL_KLV_IDX_NULL_DATA (0).
This only works now because we don't support concurrent
connected stations yet)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
|
|
The driver used siso20 in this case for legacy reasons.
Reported-by: Ido Reis <idor@ti.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
|
|
The interrupt line is enabled by wl12xx_enable_interrupts and
wl18xx_enable_interrupts, but it will not be disabled in all failure
paths. Fix this.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
|
|
While recursive recovery is avoided during shutdown, a new recovery may
be queued when the FW boots. The recovery work will then try to stop an
already stopped hardware, which will most likely result in a kernel
panic.
Fix this by verifying that wl->state is on before queueing a new
recovery.
Signed-off-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
|
|
add phy_fw_version_str to debugfs driver_state file.
information is taken during boot and stored in wl->chip.phy_fw_ver_str.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
|
|
Limit SPI transmissions to the wl12xx max buffer size, as only 12xx was
tested with SPI.
This allows us to remove the global aggregation buffer constant.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
|
|
Use number_of_assembled_ant5 phy param to indicate if A band is enabled:
if number_of_assembled_ant5 != 0 then it is enabled otherwise it is
disabled.
This aligns with phy implementation that uses this param both to indicate
if band is active and the number of antennas.
This parameter replaces enable_11a module param that was removed.
User-Space applications can use wlconf and/or INI files to disable A band
using this parameter.
Signed-off-by: Yair Shapira <yair.shapira@ti.com>
Signed-off-by: Igal Chernobelsky <igalc@ti.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
|
|
This allows us to have a p2p-management interface (in STA mode),
as we as a group dedicated interface.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
|
|
Enable device roles just before starting it.
This way, a single device role should be enough
for all vifs, as we can't use concurrent device
roles (which require ROC) anyway.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
|
|
enabled (but not-started) sta role should be good enough
for scanning (both normal and scheduled), so use it
instead of the device_role.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
|
|
Make debug prints operational when dynamic debug is not defined.
This allows better debugging in production environments.
Change the driver prefix to "wlcore" while were at it.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
|
|
Allow 3 native mac addresses on 18xx. On 12xx allow 2 native mac
addresses and set the LAA bit to create a third mac address. This
enabled operation with a separate group interface.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <luca@coelho.fi>
|
