| Age | Commit message (Collapse) | Author |
|---|
|
There is plenty of consumer hardware (e.g., mac books) that does not use AT
keyboards or PS/2 mice. It therefore makes sense for distro kernels to
build the related drivers as modules to avoid loading them on hardware that
does not need them. As such, these options should no longer be protected by
EXPERT.
Moreover, building these drivers as modules gets rid of the following ugly
error during boot:
[ 2.337745] i8042: PNP: No PS/2 controller found. Probing ports directly.
[ 3.439537] i8042: No controller found
Signed-off-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This allows the module to be autoloaded in the common case.
In order to work on non-PnP systems the module should be compiled in or
loaded unconditionally at boot (c.f. modules-load.d(5)), as before.
Signed-off-by: Tom Gundersen <teg@jklm.no>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
evdev always tries to allocate the event buffer for clients using
kzalloc rather than vmalloc, presumably to avoid mapping overhead where
possible. However, drivers like bcm5974, which claims support for
reporting 16 fingers simultaneously, can have an extraordinarily large
buffer. The resultant contiguous order-4 allocation attempt fails due
to fragmentation, and the device is thus unusable until reboot.
Try kzalloc if we can to avoid the mapping overhead, but if that fails,
fall back to vzalloc.
Signed-off-by: Daniel Stone <daniels@collabora.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Main hardware parts of the (Armada 370 based) NETGEAR ReadyNAS 104 are
supported by mainline kernel (USB 3.0 rear ports, USB 2.0 front port,
Gigabit controller and PHYs, serial port, LEDs, buttons, SATA ports,
G762 fan controller) and referenced in provided .dts file. Some additonal
work remains for:
- Intersil ISL12057 I2C RTC and Alarm chip: working driver but needs
to be splitted for submission of RTC part first;
- Front LCD (Winstar 1602G): driver needs to be written
- Armada NAND controller (to access onboard 128MB of NAND): support
being pushed by @free-electrons people
- 4 front SATA LEDs controlled via GPIO brought by NXP PCA9554:
driver is available upstream. Not referenced/tested yet.
but the device is usable w/o those.
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
|
|
If hardware (or firmware) detects palm on the surface of the device it does
not mean that the data packet is bad from the protocol standpoint. Instead
of reporting PSMOUSE_BAD_DATA in this case simply threat it as if nothing
touches the surface.
BugLink: http://bugs.launchpad.net/bugs/1229361
Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Tested-by: Kamal Mostafa <kamal@canonical.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Remove original filter from rsnd_dma_init(),
and use SH-DMA suitable filter.
This new style can be used from Device Tree.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
|
|
Most of the kernel code assumes that max*pfn is maximum pfns because
the physical start of memory is expected to be PFN0. Since this
assumption is not true on ARM architectures, the meaning of max*pfn
is number of memory pages. This is done to keep drivers happy which
are making use of of these variable to calculate the dma bounce limit
using dma_mask.
Now since we have a architecture override possibility for DMAable
maximum pfns, lets make meaning of max*pfns as maximum pnfs on ARM
as well.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Nicolas Pitre <nicolas.pitre@linaro.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
DMA bounce limit is the maximum direct DMA'able memory beyond which
bounce buffers has to be used to perform dma operations. MMC queue layr
relies on dma_mask but its calculation is based on max_*pfn which
don't have uniform meaning across architectures. So make use of
dma_max_pfn() which is expected to return the DMAable maximum pfn
value across architectures.
Cc: Chris Ball <cjb@laptop.org>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
DMA bounce limit is the maximum direct DMA'able memory beyond which
bounce buffers has to be used to perform dma operations. SCSI driver
relies on dma_mask but its calculation is based on max_*pfn which
don't have uniform meaning across architectures. So make use of
dma_max_pfn() which is expected to return the DMAable maximum pfn
value across architectures.
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Most of the kernel assumes that PFN0 is the start of the physical
memory (RAM). This assumptions is not true on most of the ARM SOCs
and hence and if one try to update the ARM port to follow the assumptions,
we end of breaking the dma bounce limit for few block layer drivers.
One such example is trying to unify the meaning of max*_pfn on ARM
as the bootmem layer expects, breaks few block layer driver dma
bounce limit.
To fix this problem, we introduce dma_max_pfn(dev) generic helper with
a possibility of override from the architecture code. The helper converts
a DMA bitmask of bits to a block PFN number. In all the generic cases,
it is just "dev->dma_mask >> PAGE_SHIFT" and hence default behavior
is maintained as is.
Subsequent patches will make use of the helper. No functional change.
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
blk_queue_bounce_limit()
The blk_queue_bounce_limit() API parameter 'dma_mask' is actually the
maximum address the device can handle rather than a dma_mask. Rename
it accordingly to avoid it being interpreted as dma_mask.
No functional change.
The idea is to fix the bad assumptions about dma_mask wherever it could
be miss-interpreted.
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
We need to start treating DMA masks as something which is specific to
the bus that the device resides on, otherwise we're going to hit all
sorts of nasty issues with LPAE and 32-bit DMA controllers in >32-bit
systems, where memory is offset from PFN 0.
In order to start doing this, we convert the DMA mask to a PFN using
the device specific dma_to_pfn() macro. This is the reverse of the
pfn_to_dma() macro which is used to get the DMA address for the device.
This gives us a PFN mask, which we can then check against the PFN
limit of the DMA zone.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The dma mask is not configured in the current code.
This was triggered by soc-dmaengine-pcm which allocate the dma
buffers with the imx-sdma as device.
This commit fix audio on imx31.
Signed-off-by: Philippe Rétornaz <philippe.retornaz@epfl.ch>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This driver doesn't need to directly access DMA masks if it uses the
platform_device_register_full() API rather than
platform_device_register_simple() - the former function can initialize
the DMA mask appropriately.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
dcdbas was explicitly initializing DMA masks thusly:
dcdbas_pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
dcdbas_pdev->dev.dma_mask = &dcdbas_pdev->dev.coherent_dma_mask;
which bypasses the architecture check. Moreover, it is creating the
dcdbas_pdev device itself, and using the platform_device_register_full()
avoids some of this explicit initialization.
Convert the driver to use platform_device_register_full(), and as it
makes use of coherent DMA, also call dma_set_coherent_mask() to ensure
that the architecture gets to check the mask.
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
register_platform_device_full() can setup the DMA mask provided the
appropriate member is set in struct platform_device_info. So lets
make that be the case. This avoids a direct reference to the DMA
masks by this driver.
While here, add the dma_set_mask_and_coherent() call which the DMA API
requires DMA-using drivers to call.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
messing with dma masks
Use platform_device_register_full() for those drivers which can, to
avoid messing directly with DMA masks. This can only be done when
the driver does not need to access the allocated musb platform device
from within its callbacks, which may be called during the musb
device probing.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Don't statically allocate struct device's in modules, and shut the
warning up with an empty release() function. There's a reason that
warning is there and that's not for people to hide in this way. It's
there to persuade people to use the correct APIs to allocate platform
devices.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The correct way for a driver to specify the coherent DMA mask is
not to directly access the field in the struct device, but to use
dma_set_coherent_mask(). Only arch and bus code should access this
member directly.
Convert all direct write accesses to using the correct API.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The correct way for a driver to specify the coherent DMA mask is
not to directly access the field in the struct device, but to use
dma_set_coherent_mask(). Only arch and bus code should access this
member directly.
Convert all direct write accesses to using the correct API.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The correct way for a driver to specify the coherent DMA mask is
not to directly access the field in the struct device, but to use
dma_set_coherent_mask(). Only arch and bus code should access this
member directly.
Convert all direct write accesses to using the correct API.
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The code sequence:
dev->coherent_dma_mask = DMA_BIT_MASK(24);
dev->dma_mask = &dev->coherent_dma_mask;
bypasses the architectures check on the DMA mask. It can be replaced
with dma_coerce_mask_and_coherent(), avoiding the direct initialization
of this mask.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The code sequence:
pdev->dev.coherent_dma_mask = DMA_BIT_MASK(64);
pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
bypasses the architectures check on the DMA mask. It can be replaced
with dma_coerce_mask_and_coherent(), avoiding the direct initialization
of this mask.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The code sequence:
pldat->pdev->dev.coherent_dma_mask = 0xFFFFFFFF;
pldat->pdev->dev.dma_mask = &pldat->pdev->dev.coherent_dma_mask;
bypasses the architectures check on the DMA mask. It can be replaced
with dma_coerce_mask_and_coherent(), avoiding the direct initialization
of this mask.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The code sequence:
dev->dma_mask = &dev->coherent_dma_mask;
dev->coherent_dma_mask = dma_mask;
bypasses the architectures check on the DMA mask. It can be replaced
with dma_coerce_mask_and_coherent(), avoiding the direct initialization
of this mask.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The code sequence:
isp->raw_dmamask = DMA_BIT_MASK(32);
isp->dev->dma_mask = &isp->raw_dmamask;
isp->dev->coherent_dma_mask = DMA_BIT_MASK(32);
bypasses the architectures check on the DMA mask. It can be replaced
with dma_coerce_mask_and_coherent(), avoiding the direct initialization
of this mask.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This code sequence:
if (!pdev->dev.dma_mask) {
pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
pdev->dev.coherent_dma_mask = DMA_BIT_MASK(32);
}
bypasses the architectures check on the DMA mask. It can be replaced
with dma_coerce_mask_and_coherent(), avoiding the direct initialization
of this mask.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Convert this code sequence:
pdev->dev.coherent_dma_mask = DMA_BIT_MASK(64);
pdev->dev.dma_mask = &pdev->dev.coherent_dma_mask;
to use dma_coerce_mask_and_coherent() to avoid bypassing the architecture
check on the DMA mask.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
This code sequence is unsafe in modules:
static u64 mask = DMA_BIT_MASK(something);
...
if (!dev->dma_mask)
dev->dma_mask = &mask;
as if a module is reloaded, the mask will be pointing at the original
module's mask address, and this can lead to oopses. Moreover, they
all follow this with:
if (!dev->coherent_dma_mask)
dev->coherent_dma_mask = mask;
where 'mask' is the same value as the statically defined mask, and this
bypasses the architecture's check on whether the DMA mask is possible.
Fix these issues by using the new dma_coerce_coherent_and_mask()
function.
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Many drivers contain code such as:
dev->dma_mask = &dev->coherent_dma_mask;
dev->coherent_dma_mask = MASK;
Let's move this pattern out of drivers and have the DMA API provide a
helper for it. This helper uses dma_set_mask_and_coherent() to allow
platform issues to be properly dealt with via dma_set_mask()/
dma_is_supported().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Add a comment to explain why this driver doesn't call any of the DMA
API dma_set_mask() functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The DMA API requires drivers to call the appropriate dma_set_mask()
functions before doing any DMA mapping. Add this required call to
the AMBA PL08x driver.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The DMA API requires drivers to call the appropriate dma_set_mask()
functions before doing any DMA mapping. Add this required call to
the AMBA PL330 driver.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
The DMA API requires drivers to call the appropriate dma_set_mask()
functions before doing any DMA mapping. Add this required call to
the AMBA PL08x driver.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
AMBA Primecell devices always treat streaming and coherent DMA exactly
the same, so there's no point in having the masks separated.
Acked-by: Grant Likely <grant.likely@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
new helper
Replace the following sequence:
dma_set_mask(dev, mask);
dma_set_coherent_mask(dev, mask);
with a call to the new helper dma_set_mask_and_coherent().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
helper
Replace the following sequence:
dma_set_mask(dev, mask);
dma_set_coherent_mask(dev, mask);
with a call to the new helper dma_set_mask_and_coherent().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
with new helper
Replace the following sequence:
dma_set_mask(dev, mask);
dma_set_coherent_mask(dev, mask);
with a call to the new helper dma_set_mask_and_coherent().
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Driver core clears the driver data to NULL after device_release
or on probe failure, so just remove it from here.
Driver core change:
"device-core: Ensure drvdata = NULL when no driver is bound"
(sha1: 0998d0631001288a5974afc0b2a5f568bcdecb4d)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
|
|
This patch adds __init to the ACPICA documented initializers:
acpi_initialize_tables()
acpi_initialize_subsystem()
acpi_load_tables()
acpi_enable_subsystem()
acpi_initialize_objects()
and to acpi_reallocate_root_table(), acpi_find_root_pointer() which
are also meant to be called only during initialization.
This patch adds __init to the ACPICA documented finalizer:
acpi_terminate()
as this finalizer is only called in __init function now.
This change helps to reduce source code differences between
ACPICA upstream and Linux.
[rjw: Changelog]
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add an asmlinkage wrapper around acpi_enter_sleep_state() to prevent
an empty stub from being called by assmebly code for ACPI_REDUCED_HARDWARE
set.
As arch/x86/kernel/acpi/wakeup_xx.S is only compiled when CONFIG_ACPI=y
and there are no users of ACPI_HARDWARE_REDUCED, currently this is in
fact not a real issue, but a cleanup to reduce source code differences
between Linux and ACPICA upstream.
[rjw: Changelog]
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch updates header files used by acpidump to reduce the
source code differences between Linux and ACPICA upstream.
This patch does not affect the generation of the Linux kernel binary.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch updates architecture specific environment settings to reduce
source differences between Linux and ACPICA upstream.
This patch does not affect the generation of the Linux kernel binary.
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Function acpi_ut_delete_caches() is meant to be used to implement
ACPI_ALLOCATE()/ACPI_FREE() mechanisms in ACPICA, so it should call
acpi_os_free() rather than ACPI_FREE(). Linux is not affected by this
issue as it uses kmem_cache instead of the ACPICA local cache, but
the change helps to reduce source code differences between Linux and
ACPICA upstream.
[rjw: Changelog]
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Reversion commit 7cb7f45c7fee (Revert "ACPICA: Remove obsolete
acpi_os_validate_address interface") restored a piece of dead code
related to an obselete AOPOBJ_INVALID flag. Remove that code again.
This helps to reduce source code differences between Linux and ACPICA
upstream.
[rjw: Changelog]
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch removes unnecessary memset() invocations where
kmem_cache_zalloc() is used for allocating memory. It also helps to
reduce source code differences between ACPICA upstream and Linux.
[rjw: Changelog]
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
ACPI_FREE() should always be used to free objects allocated with
ACPI_ALLOCATE_ZEROED(), so make acpi_ut_create_package_object() do
that.
This patch ports a fix from ACPICA upstream to Linux and helps to
reduce source code differences between them.
[rjw: Changelog]
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The object length returned by acpi_ut_get_simple_object_size() should
be rounded up to the closest word boundary.
This patch ports a fix from ACPICA upstream to Linux.
[rjw: Changelog]
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
