| Age | Commit message (Collapse) | Author |
|---|
|
Micron has released an updated firmware (MU02) for M510/M550/MX100
drives to fix the issues with queued TRIM. Queued TRIM remains broken on
M500 but is working fine on later drives such as M600 and MX200.
Tweak our blacklist to reflect the above.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=71371
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Cc: stable@vger.kernel.org
Signed-off-by: Tejun Heo <tj@kernel.org>
|
|
The maximum word size is 64-bits since MSA state is saved using st.d
which stores two 64-bit words, therefore reimplement FPR_IDX using xor,
and only within each 64-bit word.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9169/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
This reverts commit 02987633df7ba2f62967791dda816eb191d1add3.
The basic premise of the patch was incorrect since MSA context
(including FP state) is saved using st.d which stores two consecutive
64-bit words in memory rather than a single 128-bit word. This means
that even with big endian MSA, the FP state is still in the first 64-bit
word.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9168/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The expected semantics of __enable_fpu are for the FPU to be enabled
in the given mode if possible, otherwise for the FPU to be left
disabled and SIGFPE returned. The FPU was incorrectly being left
enabled in cases where the desired value for FR was unavailable.
Without ensuring the FPU is disabled in this case, it would be
possible for userland to go on to execute further FP instructions
natively in the incorrect mode, rather than those instructions being
trapped & emulated as they need to be.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9167/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
If a ptracee has not used the FPU and the ptracer sets its FP context
using PTRACE_POKEUSR, PTRACE_SETFPREGS or PTRACE_SETREGSET then that
context will be discarded upon either the ptracee using the FPU or a
further write to the context via ptrace. Prevent this loss by recording
that the task has "used" math once its FP context has been written to.
The context initialisation code that was present for the PTRACE_POKEUSR
case is reused for the other 2 cases to provide consistent behaviour
for the different ptrace requests.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9166/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
When running the emulator to handle an instruction that raised an FP
unimplemented operation exception, the FCSR cause bits were being
cleared. This is done to ensure that the kernel does not take an FP
exception when later restoring FP context to registers. However, this
was not being done when the emulator is invoked in response to a
coprocessor unusable exception. This happens in 2 cases:
- There is no FPU present in the system. In this case things were
OK, since the FP context is never restored to hardware registers
and thus no FP exception may be raised when restoring FCSR.
- The FPU could not be configured to the mode required by the task.
In this case it would be possible for the emulator to set cause
bits which are later restored to hardware if the task migrates
to a CPU whose associated FPU does support its mode requirements,
or if the tasks FP mode requirements change.
Consistently clear the cause bits after invoking the emulator, by moving
the clearing to process_fpemu_return and ensuring this is always called
before the tasks FP context is restored. This will make it easier to
catch further paths invoking the emulator in future, as will be
introduced in further patches.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9165/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Much like for traditional scalar FP exceptions, the cause bits in the
MSACSR register need to be cleared following an MSA FP exception.
Without doing so the exception will simply be raised again whenever
the kernel restores MSACSR from a tasks saved context, leading to
undesirable spurious exceptions. Clear the cause bits from the
handle_msa_fpe function, mirroring the way handle_fpe clears the
cause bits in FCSR.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9164/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Uses of the cfcmsa & ctcmsa instructions were not being wrapped by a
macro in the case where the toolchain supports MSA, since the arguments
exactly match a typical use of the instructions. However using current
toolchains this leads to errors such as:
arch/mips/kernel/genex.S:437: Error: opcode not supported on this processor: mips32r2 (mips32r2) `cfcmsa $5,1'
Thus uses of the instructions must be in the context of a ".set msa"
directive, however doing that from the users of the instructions would
be messy due to the possibility that the toolchain does not support
MSA. Fix this by renaming the macros (prepending an underscore) in order
to avoid recursion when attempting to emit the instructions, and provide
implementations for the TOOLCHAIN_SUPPORTS_MSA case which ".set msa" as
appropriate.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9163/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Recursive macros made the code more concise & worked great for the
case where the toolchain doesn't support MSA. However, with toolchains
which do support MSA they lead to build failures such as:
arch/mips/kernel/r4k_switch.S: Assembler messages:
arch/mips/kernel/r4k_switch.S:148: Error: invalid operands `insert.w $w(0+1)[2],$1'
arch/mips/kernel/r4k_switch.S:148: Error: invalid operands `insert.w $w(0+1)[3],$1'
arch/mips/kernel/r4k_switch.S:148: Error: invalid operands `insert.w $w((0+1)+1)[2],$1'
arch/mips/kernel/r4k_switch.S:148: Error: invalid operands `insert.w $w((0+1)+1)[3],$1'
...
Drop the recursion from msa_init_all_upper invoking the msa_init_upper
macro explicitly for each vector register.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9162/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Assuming at ($1) as the source or destination register of copy or
insert instructions:
- Simplifies the macros providing those instructions for toolchains
without MSA support.
- Avoids an unnecessary move instruction when at is used as the source
or destination register anyway.
- Is sufficient for the uses to be introduced in the kernel by a
subsequent patch.
Note that due to a patch ordering snafu on my part this also fixes the
currently broken build with MSA support enabled. The build has been
broken since commit c9017757c532 "MIPS: init upper 64b of vector
registers when MSA is first used", which this patch should have
preceeded.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9161/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The {save,restore}_fp_context{,32} functions require that the assembler
allows the use of sdc instructions on any FP register, and this is
acomplished by setting the arch to mips64r2 or mips64r6
(using MIPS_ISA_ARCH_LEVEL_RAW).
However this has the effect of enabling the assembler to use mips64
instructions in the expansion of pseudo-instructions. This was done in
the (now-reverted) commit eec43a224cf1 "MIPS: Save/restore MSA context
around signals" which led to my mistakenly believing that there was an
assembler bug, when in reality the assembler was just emitting mips64
instructions. Avoid the issue for future commits which will add code to
r4k_fpu.S by pushing the .set MIPS_ISA_ARCH_LEVEL_RAW directives into
the functions that require it, and remove the spurious assertion
declaring the assembler bug.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
[james.hogan@imgtec.com: Rebase on v4.0-rc1 and reword commit message to
reflect use of MIPS_ISA_ARCH_LEVEL_RAW]
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9612/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
The lose_fpu() function only disables the FPU in CP0_Status.CU1 if the
FPU is in use and MSA isn't enabled.
This isn't necessarily a problem because KSTK_STATUS(current), the
version of CP0_Status stored on the kernel stack on entry from user
mode, does always get updated and gets restored when returning to user
mode, but I don't think it was intended, and it is inconsistent with the
case of only the FPU being in use. Sometimes leaving the FPU enabled may
also mask kernel bugs where FPU operations are executed when the FPU
might not be enabled.
So lets disable the FPU in the MSA case too.
Fixes: 33c771ba5c5d ("MIPS: save/disable MSA in lose_fpu")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/9323/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
|
|
Otherwise the VCE firmware needs to be in the first 256MB of VRAM.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Dumping is still possible if a ring isn't ready, only when it
isn't allocated at all we need to abort here.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Use readb() and memcpy_fromio() accessors instead.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
Need to expand the check to handle short circuiting
if the selected state is the same as current state.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=87796
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
If the user supplies EDID through firmware or debugfs override, the
driver callbacks are bypassed and the connector ELD does not get
updated, and audio fails. Set ELD for firmware and debugfs EDIDs too.
There should be no harm in gratuitously doing this for non HDMI/DP
connectors, as it's still up to the driver to use the ELD, if any.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=82349
Reference: https://bugs.freedesktop.org/show_bug.cgi?id=80691
Reported-by: Emil <emilsvennesson@gmail.com>
Reported-by: Rob Engle <grenoble@gmail.com>
Tested-by: Jolan Luff <jolan@gormsby.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: stable@vger.kernel.org
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
locks_delete_lock_ctx() is called inside the loop, so we
should use list_for_each_entry_safe.
Fixes: 8634b51f6ca2 (locks: convert lease handling to file_lock_context)
Signed-off-by: "Yan, Zheng" <zyan@redhat.com>
Signed-off-by: Jeff Layton <jeff.layton@primarydata.com>
|
|
dmi_num is a u16, dmi_len is a u32, so this construct:
dmi_num = dmi_len / 4;
would result in an integer overflow for a DMI table larger than
256 kB. I've never see such a large table so far, but SMBIOS 3.0
makes it possible so maybe we'll see such tables in the future.
So instead of faking a structure count when the entry point does
not provide it, adjust the loop condition in dmi_table() to properly
deal with the case where dmi_num is not set.
This bug was introduced with the initial SMBIOS 3.0 support in commit
fc43026278b2 ("dmi: add support for SMBIOS 3.0 64-bit entry point").
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Cc: <stable@vger.kernel.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
|
|
Now GPIO syscon driver produces bunch of warnings during the
boot of Kesytone 2 SoCs:
gpio-syscon soc:keystone_dsp_gpio@02620240: can't read the dir register offset!
gpio-syscon soc:keystone_dsp_gpio@2620244: can't read the dir register offset!
This message unintentionally was added using dev_err(), but its
actual log level is debug, because third cell of "ti,syscon-dev" is
optional.
Hence change it to dev_dbg() as it should be.
This patch fixes commit:
5a3e3f8 ("gpio: syscon: retriave syscon node and regs offsets from dt")
Reported-by: Russell King <linux@arm.linux.org.uk>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
into for-linus
|
|
The IMG PDC watchdog driver heartbeat module parameter has no default so
it is initialised to zero. This results in the following warning during
probe:
imgpdc-wdt 2006000.wdt: Initial timeout out of range! setting max timeout
The module parameter description implies that the default value should
be PDC_WDT_DEF_TIMEOUT, which isn't yet used, so initialise it to that.
Also tweak the heartbeat module parameter description for consistency.
Fixes: 93937669e9b5 ("watchdog: ImgTec PDC Watchdog Timer Driver")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Naidu Tellapati <Naidu.Tellapati@imgtec.com>
Cc: Jude Abraham <Jude.Abraham@imgtec.com>
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
The IMG PDC watchdog probe function calls pdc_wdt_stop() prior to
watchdog_set_drvdata(), causing a NULL pointer dereference when
pdc_wdt_stop() retrieves the struct pdc_wdt_dev pointer using
watchdog_get_drvdata() and reads the register base address through it.
Fix by moving the watchdog_set_drvdata() call earlier, to where various
other pdc_wdt->wdt_dev fields are initialised.
Fixes: 93937669e9b5 ("watchdog: ImgTec PDC Watchdog Timer Driver")
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Ezequiel Garcia <ezequiel.garcia@imgtec.com>
Cc: Naidu Tellapati <Naidu.Tellapati@imgtec.com>
Cc: Jude Abraham <Jude.Abraham@imgtec.com>
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
"ret" should be signed for the error handling to work correctly. This
doesn't matter much in real life since mtk_wdt_set_timeout() always
succeeds.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
|
|
If the guest CPU is supposed to support rdtscp and the host has rdtscp
enabled in the secondary execution controls, we can also expose this
feature to L1. Just extend nested_vmx_exit_handled to properly route
EXIT_REASON_RDTSCP.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
|
|
When the receiver was enabled during startup, a character could
have been in the FIFO when the UART get initially used. The
driver configures the (receive) watermark level, and flushes the
FIFO. However, the receive flag (RDRF) could still be set at that
stage (as mentioned in the register description of UARTx_RWFIFO).
This leads to an interrupt which won't be handled properly in
interrupt mode: The receive interrupt function lpuart_rxint checks
the FIFO count, which is 0 at that point (due to the flush
during initialization). The problem does not manifest when using
DMA to receive characters.
Fix this situation by explicitly read the status register, which
leads to clearing of the RDRF flag. Due to the flush just after
the status flag read, a explicit data read is not to required.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Specify transmit FIFO size which might be different depending on
LPUART instance. This makes sure uart_wait_until_sent in serial
core getting called, which in turn waits and checks if the FIFO
is really empty on shutdown by using the tx_empty callback.
Without the call of this callback, the last several characters
might not yet be transmitted when closing the serial port. This
can be reproduced by simply using echo and redirect the output to
a ttyLP device.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Exynos serial ports operate either in a DMA-based or interrupt-based
modes. In DMA-based mode, the UART generates a transfer data request
and a Transmission (Tx) interrupt in interrupt-based mode.
The Tx IRQ is only unmasked in interrupt-based mode and it was done
in s3c24xx_serial_start_tx(). Commit ba019a3e2ad5 ("serial: samsung:
remove redundant interrupt enabling") removed the IRQ enable on that
function since it is enabled when the mode is set in enable_tx_pio().
The problem is that enable_tx_pio() is only called if the port mode
has not been set before but the mode was not cleared on .shutdown().
So if the UART was shutdown and then started up again, the mode set
will remain and the Tx IRQ won't be unmasked.
This caused a hang on at least Exynos5250, Exynos5420 and Exynos5800
when the system is rebooted or powered off.
Fixes: ba019a3e2ad5 ("serial: samsung: remove redundant interrupt enabling")
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull drm refcounting fixes from Dave Airlie:
"Here is the complete set of i915 bug/warn/refcounting fixes"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Fixup legacy plane->crtc link for initial fb config
drm/i915: Fix atomic state when reusing the firmware fb
drm/i915: Keep ring->active_list and ring->requests_list consistent
drm/i915: Don't try to reference the fb in get_initial_plane_config()
drm: Fixup racy refcounting in plane_force_disable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
"Fix DM core device cleanup regression -- due to a latent race that was
exposed by the bdi changes that were introduced during the 4.0 merge"
* tag 'dm-4.0-fix-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: fix add_disk() NULL pointer due to race with free_dev()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest
Pull kselftest fix from Shuah Khan.
* tag 'linux-kselftest-4.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux-kselftest:
selftests: Fix build failures when invoked from kselftest target
|
|
Using the framework provided by the recent vgic.c changes we register
a kvm_io_bus device when initializing the virtual GICv2.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Currently we use a lot of VGIC specific code to do the MMIO
dispatching.
Use the previous reworks to add kvm_io_bus style MMIO handlers.
Those are not yet called by the MMIO abort handler, also the actual
VGIC emulator function do not make use of it yet, but will be enabled
with the following patches.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The vgic_find_range() function in vgic.c takes a struct kvm_exit_mmio
argument, but actually only used the length field in there. Since we
need to get rid of that structure in that part of the code anyway,
let's rework the function (and it's callers) to pass the length
argument to the function directly.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
The name "kvm_mmio_range" is a bit bold, given that it only covers
the VGIC's MMIO ranges. To avoid confusion with kvm_io_range, rename
it to vgic_io_range.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
virt/kvm was never really a good include directory for anything else
than locally included headers.
With the move of iodev.h there is no need anymore to add this
directory the compiler's include path, so remove it from the x86 kvm
Makefile.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
virt/kvm was never really a good include directory for anything else
than locally included headers.
With the move of iodev.h there is no need anymore to add this
directory the compiler's include path, so remove it from the arm and
arm64 kvm Makefile.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
iodev.h contains definitions for the kvm_io_bus framework. This is
needed both by the generic KVM code in virt/kvm as well as by
architecture specific code under arch/. Putting the header file in
virt/kvm and using local includes in the architecture part seems at
least dodgy to me, so let's move the file into include/kvm, so that a
more natural "#include <kvm/iodev.h>" can be used by all of the code.
This also solves a problem later when using struct kvm_io_device
in arm_vgic.h.
Fixing up the FSF address in the GPL header and a wrong include path
on the way.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Reviewed-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
This is needed in e.g. ARM vGIC emulation, where the MMIO handling
depends on the VCPU that does the access.
Signed-off-by: Nikolay Nikolaev <n.nikolaev@virtualopensystems.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Christoffer Dall <christoffer.dall@linaro.org>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
git://anongit.freedesktop.org/drm-intel into drm-fixes
This should cover the final warnings in -rc5 with two more backports
from our development branch (drm-intel-next-queued). They're the ones
from Daniel and Damien, with references to the reports.
This is on top of drm-fixes because of the dependency on the two earlier
fixes not yet in Linus' tree.
There's an additional regression fix from Chris.
* tag 'drm-intel-fixes-2015-03-26' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Fixup legacy plane->crtc link for initial fb config
drm/i915: Fix atomic state when reusing the firmware fb
drm/i915: Keep ring->active_list and ring->requests_list consistent
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 fixes from Martin Schwidefsky:
"A couple of bug fixes for s390.
The ftrace comile fix is quite large for a -rc6 release, but it would
be nice to have it in 4.0"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/smp: reenable smt after resume
s390/mm: limit STACK_RND_MASK for compat tasks
s390/ftrace: fix compile error if CONFIG_KPROBES is disabled
s390/cpum_sf: add diagnostic sampling event only if it is authorized
|
|
There is no reason to pass static vars to function that can use
only them.
The dmi_table() can use only dmi_len and dmi_num static vars, so use
them directly. In this case we can freely change their type in one
place and slightly decrease redundancy.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
|
|
New SMBIOS3 spec adds additional field for versioning - docrev.
The docrev identifies the revision of a specification implemented in
the table structures, so display SMBIOSv3 versions in format,
like "3.22.1".
In case of only 32 bit entry point for versions > 3 display
dmi version like "3.22.x" as we don't know the docrev.
In other cases display version like it was.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
|
|
This is a very similar bug in the load detect code fixed in
commit 9128b040eb774e04bc23777b005ace2b66ab2a85
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Mar 3 17:31:21 2015 +0100
drm/i915: Fix modeset state confusion in the load detect code
But this time around it was the initial fb code that forgot to update
the plane->crtc pointer. Otherwise it's the exact same bug, with the
exact same restrains (any set_config call/ioctl that doesn't disable
the pipe papers over the bug for free, so fairly hard to hit in normal
testing). So if you want the full explanation just go read that one
over there - it's rather long ...
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Josh Boyer <jwboyer@fedoraproject.org>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reported-and-tested-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: backported to drm-intel-fixes for v4.0-rc]
Reference: http://mid.gmane.org/CA+5PVA7ChbtJrknqws1qvZcbrg1CW2pQAFkSMURWWgyASRyGXg@mail.gmail.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
Right now, we get a warning when taking over the firmware fb:
[drm:drm_atomic_plane_check] FB set but no CRTC
with the following backtrace:
[<ffffffffa010339d>] drm_atomic_check_only+0x35d/0x510 [drm]
[<ffffffffa0103567>] drm_atomic_commit+0x17/0x60 [drm]
[<ffffffffa00a6ccd>] drm_atomic_helper_plane_set_property+0x8d/0xd0 [drm_kms_helper]
[<ffffffffa00f1fed>] drm_mode_plane_set_obj_prop+0x2d/0x90 [drm]
[<ffffffffa00a8a1b>] restore_fbdev_mode+0x6b/0xf0 [drm_kms_helper]
[<ffffffffa00aa969>] drm_fb_helper_restore_fbdev_mode_unlocked+0x29/0x80 [drm_kms_helper]
[<ffffffffa00aa9e2>] drm_fb_helper_set_par+0x22/0x50 [drm_kms_helper]
[<ffffffffa050a71a>] intel_fbdev_set_par+0x1a/0x60 [i915]
[<ffffffff813ad444>] fbcon_init+0x4f4/0x580
That's because we update the plane state with the fb from the firmware, but we
never associate the plane to that CRTC.
We don't quite have the full DRM take over from HW state just yet, so
fake enough of the plane atomic state to pass the checks.
v2: Fix the state on which we set the CRTC in the case we're sharing the
initial fb with another pipe. (Matt)
Signed-off-by: Damien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
[Jani: backported to drm-intel-fixes for v4.0-rc]
Reference: http://mid.gmane.org/CA+5PVA7yXH=U757w8V=Zj2U1URG4nYNav20NpjtQ4svVueyPNw@mail.gmail.com
Reference: http://lkml.kernel.org/r/CA+55aFweWR=nDzc2Y=rCtL_H8JfdprQiCimN5dwc+TgyD4Bjsg@mail.gmail.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
We have a HP machine which use the codec node 0x17 connecting the
internal speaker, and from the node capability, we saw the EAPD,
if we don't set the EAPD on for this node, the internal speaker
can't output any sound.
Cc: <stable@vger.kernel.org>
BugLink: https://bugs.launchpad.net/bugs/1436745
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The sun5i timer is used as the sched-clock on certain systems, and ever
since we started using cpufreq, the cpu clock (that is one of the
timer's clock indirect parent) now changes as well, along with the
actual sched_clock() rate.
This is not accurate and not desirable.
We can safely remove the sun5i sched-clock on those systems, since we
have other reliable sched_clock() sources in the system.
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
[ Improved the changelog. ]
Cc: richard@nod.at
Link: http://lkml.kernel.org/r/1427362029-6511-4-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Fix !CONFIG_HAS_IOMEM related build failures in three clocksource drivers.
The build failures have the pattern of:
drivers/clocksource/sh_cmt.c: In function ‘sh_cmt_map_memory’: drivers/clocksource/sh_cmt.c:920:2:
error: implicit declaration of function ‘ioremap_nocache’ [-Werror=implicit-function-declaration] cmt->mapbase = ioremap_nocache(mem->start, resource_size(mem));
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: maxime.ripard@free-electrons.com
Link: http://lkml.kernel.org/r/1427362029-6511-1-git-send-email-daniel.lezcano@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
If we retire requests last, we may use a later seqno and so clear
the requests lists without clearing the active list, leading to
confusion. Hence we should retire requests first for consistency with
the early return. The order used to be important as the lifecycle for
the object on the active list was determined by request->seqno. However,
the requests themselves are now reference counted removing the
constraint from the order of retirement.
Fixes regression from
commit 1b5a433a4dd967b125131da42b89b5cc0d5b1f57
Author: John Harrison <John.C.Harrison@Intel.com>
Date: Mon Nov 24 18:49:42 2014 +0000
drm/i915: Convert 'i915_seqno_passed' calls into 'i915_gem_request_completed
'
and a
WARNING: CPU: 0 PID: 1383 at drivers/gpu/drm/i915/i915_gem_evict.c:279 i915_gem_evict_vm+0x10c/0x140()
WARN_ON(!list_empty(&vm->active_list))
Identified by updating WATCH_LISTS:
[drm:i915_verify_lists] *ERROR* blitter ring: active list not empty, but no requests
WARNING: CPU: 0 PID: 681 at drivers/gpu/drm/i915/i915_gem.c:2751 i915_gem_retire_requests_ring+0x149/0x230()
WARN_ON(i915_verify_lists(ring->dev))
Note that this is only a problem in evict_vm where the following happens
after a retire_request has cleaned out all requests, but not all active
bo:
- intel_ring_idle called from i915_gpu_idle notices that no requests are
outstanding and immediately returns.
- i915_gem_retire_requests_ring called from i915_gem_retire_requests also
immediately returns when there's no request, still leaving the bo on the
active list.
- evict_vm hits the WARN_ON(!list_empty(&vm->active_list)) after evicting
all active objects that there's still stuff left that shouldn't be
there.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: John Harrison <John.C.Harrison@Intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
|
|
The total stream number of Sunrise Point's input and output stream
exceeds 15, which will cause some streams do not work because
of the overflow on SDxCTL.STRM field if using the legacy
stream tag allocation method.
This patch uses the new stream tag allocation method by add
the flag AZX_DCAPS_SEPARATE_STREAM_TAG for Skylake platform.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
