| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds the 'device_config' and 'device_prep_slave_sg' interfaces
for users to configure DMA, as well as adding one 'struct sprd_dma_config'
structure to save Spreadtrum DMA configuration for each DMA channel.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This is one preparation patch, we can use default DMA configuration to
implement the device_prep_dma_memcpy() interface instead of issuing
sprd_dma_config().
We will implement one new sprd_dma_config() function with introducing
device_prep_slave_sg() interface in following patch. So we can remove
the obsolete sprd_dma_config() firstly.
Signed-off-by: Eric Long <eric.long@spreadtrum.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Salil Mehta says:
====================
Misc. bug fixes & some minor additions to HNS3 driver
This patch-set provides some bug fixes figured out during testing
and review. It also provides some additions due to running of the
existing code on the new revision of the HNS3 hardware.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When register a RoCE client with hnae3vf device, it needs to judge
the device whether support RoCE vf function. Otherwise, it will
lead to calltrace when RoCE is not support vf function and remove
roce device.
The calltrace as follows:
[ 93.156614] Unable to handle kernel NULL pointer dereference at virtual address 00000015
<SNIP>
[ 93.278784] Call trace:
[ 93.278788] hnae3_match_n_instantiate+0x24/0xd8 [hnae3]
[ 93.278790] hnae3_register_client+0xcc/0x150 [hnae3]
[ 93.278801] hns_roce_hw_v2_init+0x18/0x1000 [hns_roce_hw_v2]
[ 93.278805] do_one_initcall+0x58/0x160
[ 93.278807] do_init_module+0x64/0x1d8
[ 93.278809] load_module+0x135c/0x15c8
[ 93.278811] SyS_finit_module+0x100/0x118
[ 93.278816] __sys_trace_return+0x0/0x4
[ 93.278827] Code: aa0003f5 12001c56 aa1e03e0 d503201f (b9402660)
Fixes: e2cb1dec9779 ("net: hns3: Add HNS3 VF HCL(Hardware Compatibility Layer) Support")
Reported-by: Xinwei Kong <kong.kongxinwei@hisilicon.com>
Reported-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Lijun Ou <oulijun@huawei.com>
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware now supports control of all leds. Existing HNS3 driver code
only supported led locate command over SFP Fibre ports. But now it
is also supported over copper port.
This patch removes existing not needed code for the led locate
command and updates the led control command between driver and
firmware.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the previous implementation of led control for fibre port , parses the
port speed configuration, checks the link status and traffic status per
second, and updates the blink status of link led, traffic led and speed
led.
Now, the firmware takes responsibility to handle the led, the dirver just
needs to deal with locate command.
So the codes for link led, traffic led and speed led are useless now. This
patch removes these redundant codes.
Signed-off-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we down the port, some packets are left in TX/RX buffer. When we
up the port again, these old packets are forwarded to protocol stack
or are sent to internet. It will make some problem. TX/RX buffer should
be cleared when stopping port. This patch adds some function to ensure
the buffer is clean when port is started. We should clear the rings
when clients are being un-initialized as well.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Our code will ensure that hns3_clear_tx_ring is not used to cleared
RX rings and hns3_clear_rx_ring is not used to cleared TX rings. So
the ring type check is unnecessary.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
RX Buffer Descriptor contains a VALID bit which indicates if the BD
is valid and has some data. This field is set by HNS3 hardware to
intimate the driver of some valid data present in the BD. nd should
be reset by the driver when BD is being used again. In the existing
code this bit was not being (re-)initialized properly and hence was
causing problems.
Fixes: 76ad4f0ee747 ("net: hns3: Add support of HNS3 Ethernet Driver for hip08 SoC")
Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HNAE3 module supports kernel nic driver, user nic driver and roce driver,
and there are 3 client types. Driver uses one bit(HNAE3_CLIENT_INITED_B)
to indicate the client initialization state, it will cause confusion
for 3 client types. This patch fixes it by use 3 bits to indicate the
initialization state.
Fixes: 38caee9d3ee8 ("net: hns3: Add support of the HNAE3 framework")
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before the firmware updates the crq's tail pointer, if the PF driver
reads the data in the crq, the data may be incomplete at this time,
which will lead to the driver read an unknown message.
This patch fixes it by checking if crq is not empty before reading the
message.
Fixes: c1a81619d73a ("net: hns3: Add mailbox interrupt handling to PF driver")
Signed-off-by: Xi Wang <wangxi11@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HCLGE_PROMISC_TX_EN_B and HCLGE_PROMISC_RX_EN_B are not supported
on pdev revision(0x20), new revision(0x21) supports them.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hardware Revision(0x21) Buffer Descriptor adds a field STRP_TAGP
for vlan stripped processed indication. STRP_TAGP field has 2 bits,
bit 0 is stripped indication of the vlan tag in outer vlan tag
field, bit 1 is stripped indication of the vlan tag in inner vlan
tag field. For each bit, 0 indicates the tag is not stripped and
1 indicates the tag is stripped.
This patch adds STRP_TAGP support for revision(0x21), and does not
change the revision(0x20) action.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HNS3 Hardware can support up to two VLAN tags in transmit leg, the PPP
module can handle the packets based on the tag1 and tag2 config. This
patch adds support for tag2 config for vlan handling
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the latest revision of the hardware, if a packet is spanning
across multiple BDs then only VLD bit and current data size info
is valid in each BD, and rest of the information is only valid
in the last BD of the packet. In such case we should make sure
we are fetching RX packet size from the first descriptor and
information like VLAN should be fetched from last BD.
Signed-off-by: Peng Li <lipeng321@huawei.com>
Reviewed-by: Yisen Zhuang <yisen.zhuang@huawei.com>
Signed-off-by: Salil Mehta <salil.mehta@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The struct Qdisc has a lot of holes, especially after commit
a53851e2c321 ("net: sched: explicit locking in gso_cpu fallback"),
which as a side effect, moved the fields just after 'busylock'
on a new cacheline.
Since both 'padded' and 'refcnt' are not updated frequently, and
there is a hole before 'gso_skb', we can move such fields there,
saving a cacheline without any performance side effect.
Before this commit:
pahole -C Qdisc net/sche/sch_generic.o
# ...
/* size: 384, cachelines: 6, members: 25 */
/* sum members: 236, holes: 3, sum holes: 92 */
/* padding: 56 */
After this commit:
pahole -C Qdisc net/sche/sch_generic.o
# ...
/* size: 320, cachelines: 5, members: 25 */
/* sum members: 236, holes: 2, sum holes: 28 */
/* padding: 56 */
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SIMCOM are reusing a single device ID for many (all of their?)
different modems, based on different chipsets and firmwares. Newer
Qualcomm chipset generations require setting DTR to wake the QMI
function. The SIM7600E modem is using such a chipset, making it
fail to work with this driver despite the device ID match.
Fix by unconditionally enabling the SET_DTR quirk for all SIMCOM
modems using this specific device ID. This is similar to what
we already have done for another case of device IDs recycled over
multiple chipset generations: 14cf4a771b30 ("drivers: net: usb:
qmi_wwan: add QMI_QUIRK_SET_DTR for Telit PID 0x1201")
Initial testing on an older SIM7100 modem shows no immediate side
effects.
Reported-by: Sebastian Sjoholm <sebastian.sjoholm@gmail.com>
Cc: Reinhard Speyerer <rspmn@arcor.de>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The netsec network controller IP can drive 64 address bits for DMA, and
the DMA mask is set accordingly in the driver. However, the SynQuacer
SoC, which is the only silicon incorporating this IP at the moment,
integrates this IP in a manner that leaves address bits [63:40]
unconnected.
Up until now, this has not resulted in any problems, given that the DDR
controller doesn't decode those bits to begin with. However, recent
firmware updates for platforms incorporating this SoC allow the IOMMU
to be enabled, which does decode address bits [47:40], and allocates
top down from the IOVA space, producing DMA addresses that have bits
set that have been left unconnected.
Both the DT and ACPI (IORT) descriptions of the platform take this into
account, and only describe a DMA address space of 40 bits (using either
dma-ranges DT properties, or DMA address limits in IORT named component
nodes). However, even though our IOMMU and bus layers may take such
limitations into account by setting a narrower DMA mask when creating
the platform device, the netsec probe() entrypoint follows the common
practice of setting the DMA mask uncondionally, according to the
capabilities of the IP block itself rather than to its integration into
the chip.
It is currently unclear what the correct fix is here. We could hack around
it by only setting the DMA mask if it deviates from its default value of
DMA_BIT_MASK(32). However, this makes it impossible for the bus layer to
use DMA_BIT_MASK(32) as the bus limit, and so it appears that a more
comprehensive approach is required to take DMA limits imposed by the
SoC as a whole into account.
In the mean time, let's limit the DMA mask to 40 bits. Given that there
is currently only one SoC that incorporates this IP, this is a reasonable
approach that can be backported to -stable and buys us some time to come
up with a proper fix going forward.
Fixes: 533dd11a12f6 ("net: socionext: Add Synquacer NetSec driver")
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Jassi Brar <jaswinder.singh@linaro.org>
Cc: Masahisa Kojima <masahisa.kojima@linaro.org>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Robin Murphy <robin.murphy@arm.com>
Acked-by: Jassi Brar <jaswinder.singh@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
seg6_do_srh_encap and seg6_do_srh_inline can possibly do an
out-of-bounds access when adding the SRH to the packet. This no longer
happen when expanding the skb not only by the size of the SRH (+
outer IPv6 header), but also by skb->mac_len.
[ 53.793056] BUG: KASAN: use-after-free in seg6_do_srh_encap+0x284/0x620
[ 53.794564] Write of size 14 at addr ffff88011975ecfa by task ping/674
[ 53.796665] CPU: 0 PID: 674 Comm: ping Not tainted 4.17.0-rc3-ARCH+ #90
[ 53.796670] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996),
BIOS 1.11.0-20171110_100015-anatol 04/01/2014
[ 53.796673] Call Trace:
[ 53.796679] <IRQ>
[ 53.796689] dump_stack+0x71/0xab
[ 53.796700] print_address_description+0x6a/0x270
[ 53.796707] kasan_report+0x258/0x380
[ 53.796715] ? seg6_do_srh_encap+0x284/0x620
[ 53.796722] memmove+0x34/0x50
[ 53.796730] seg6_do_srh_encap+0x284/0x620
[ 53.796741] ? seg6_do_srh+0x29b/0x360
[ 53.796747] seg6_do_srh+0x29b/0x360
[ 53.796756] seg6_input+0x2e/0x2e0
[ 53.796765] lwtunnel_input+0x93/0xd0
[ 53.796774] ipv6_rcv+0x690/0x920
[ 53.796783] ? ip6_input+0x170/0x170
[ 53.796791] ? eth_gro_receive+0x2d0/0x2d0
[ 53.796800] ? ip6_input+0x170/0x170
[ 53.796809] __netif_receive_skb_core+0xcc0/0x13f0
[ 53.796820] ? netdev_info+0x110/0x110
[ 53.796827] ? napi_complete_done+0xb6/0x170
[ 53.796834] ? e1000_clean+0x6da/0xf70
[ 53.796845] ? process_backlog+0x129/0x2a0
[ 53.796853] process_backlog+0x129/0x2a0
[ 53.796862] net_rx_action+0x211/0x5c0
[ 53.796870] ? napi_complete_done+0x170/0x170
[ 53.796887] ? run_rebalance_domains+0x11f/0x150
[ 53.796891] __do_softirq+0x10e/0x39e
[ 53.796894] do_softirq_own_stack+0x2a/0x40
[ 53.796895] </IRQ>
[ 53.796898] do_softirq.part.16+0x54/0x60
[ 53.796900] __local_bh_enable_ip+0x5b/0x60
[ 53.796903] ip6_finish_output2+0x416/0x9f0
[ 53.796906] ? ip6_dst_lookup_flow+0x110/0x110
[ 53.796909] ? ip6_sk_dst_lookup_flow+0x390/0x390
[ 53.796911] ? __rcu_read_unlock+0x66/0x80
[ 53.796913] ? ip6_mtu+0x44/0xf0
[ 53.796916] ? ip6_output+0xfc/0x220
[ 53.796918] ip6_output+0xfc/0x220
[ 53.796921] ? ip6_finish_output+0x2b0/0x2b0
[ 53.796923] ? memcpy+0x34/0x50
[ 53.796926] ip6_send_skb+0x43/0xc0
[ 53.796929] rawv6_sendmsg+0x1216/0x1530
[ 53.796932] ? __orc_find+0x6b/0xc0
[ 53.796934] ? rawv6_rcv_skb+0x160/0x160
[ 53.796937] ? __rcu_read_unlock+0x66/0x80
[ 53.796939] ? __rcu_read_unlock+0x66/0x80
[ 53.796942] ? is_bpf_text_address+0x1e/0x30
[ 53.796944] ? kernel_text_address+0xec/0x100
[ 53.796946] ? __kernel_text_address+0xe/0x30
[ 53.796948] ? unwind_get_return_address+0x2f/0x50
[ 53.796950] ? __save_stack_trace+0x92/0x100
[ 53.796954] ? save_stack+0x89/0xb0
[ 53.796956] ? kasan_kmalloc+0xa0/0xd0
[ 53.796958] ? kmem_cache_alloc+0xd2/0x1f0
[ 53.796961] ? prepare_creds+0x23/0x160
[ 53.796963] ? __x64_sys_capset+0x252/0x3e0
[ 53.796966] ? do_syscall_64+0x69/0x160
[ 53.796968] ? entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 53.796971] ? __alloc_pages_nodemask+0x170/0x380
[ 53.796973] ? __alloc_pages_slowpath+0x12c0/0x12c0
[ 53.796977] ? tty_vhangup+0x20/0x20
[ 53.796979] ? policy_nodemask+0x1a/0x90
[ 53.796982] ? __mod_node_page_state+0x8d/0xa0
[ 53.796986] ? __check_object_size+0xe7/0x240
[ 53.796989] ? __sys_sendto+0x229/0x290
[ 53.796991] ? rawv6_rcv_skb+0x160/0x160
[ 53.796993] __sys_sendto+0x229/0x290
[ 53.796996] ? __ia32_sys_getpeername+0x50/0x50
[ 53.796999] ? commit_creds+0x2de/0x520
[ 53.797002] ? security_capset+0x57/0x70
[ 53.797004] ? __x64_sys_capset+0x29f/0x3e0
[ 53.797007] ? __x64_sys_rt_sigsuspend+0xe0/0xe0
[ 53.797011] ? __do_page_fault+0x664/0x770
[ 53.797014] __x64_sys_sendto+0x74/0x90
[ 53.797017] do_syscall_64+0x69/0x160
[ 53.797019] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 53.797022] RIP: 0033:0x7f43b7a6714a
[ 53.797023] RSP: 002b:00007ffd891bd368 EFLAGS: 00000246 ORIG_RAX:
000000000000002c
[ 53.797026] RAX: ffffffffffffffda RBX: 00000000006129c0 RCX: 00007f43b7a6714a
[ 53.797028] RDX: 0000000000000040 RSI: 00000000006129c0 RDI: 0000000000000004
[ 53.797029] RBP: 00007ffd891be640 R08: 0000000000610940 R09: 000000000000001c
[ 53.797030] R10: 0000000000000000 R11: 0000000000000246 R12: 0000000000000040
[ 53.797032] R13: 000000000060e6a0 R14: 0000000000008004 R15: 000000000040b661
[ 53.797171] Allocated by task 642:
[ 53.797460] kasan_kmalloc+0xa0/0xd0
[ 53.797463] kmem_cache_alloc+0xd2/0x1f0
[ 53.797465] getname_flags+0x40/0x210
[ 53.797467] user_path_at_empty+0x1d/0x40
[ 53.797469] do_faccessat+0x12a/0x320
[ 53.797471] do_syscall_64+0x69/0x160
[ 53.797473] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 53.797607] Freed by task 642:
[ 53.797869] __kasan_slab_free+0x130/0x180
[ 53.797871] kmem_cache_free+0xa8/0x230
[ 53.797872] filename_lookup+0x15b/0x230
[ 53.797874] do_faccessat+0x12a/0x320
[ 53.797876] do_syscall_64+0x69/0x160
[ 53.797878] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[ 53.798014] The buggy address belongs to the object at ffff88011975e600
which belongs to the cache names_cache of size 4096
[ 53.799043] The buggy address is located 1786 bytes inside of
4096-byte region [ffff88011975e600, ffff88011975f600)
[ 53.800013] The buggy address belongs to the page:
[ 53.800414] page:ffffea000465d600 count:1 mapcount:0
mapping:0000000000000000 index:0x0 compound_mapcount: 0
[ 53.801259] flags: 0x17fff0000008100(slab|head)
[ 53.801640] raw: 017fff0000008100 0000000000000000 0000000000000000
0000000100070007
[ 53.803147] raw: dead000000000100 dead000000000200 ffff88011b185a40
0000000000000000
[ 53.803787] page dumped because: kasan: bad access detected
[ 53.804384] Memory state around the buggy address:
[ 53.804788] ffff88011975eb80: fb fb fb fb fb fb fb fb fb fb fb fb
fb fb fb fb
[ 53.805384] ffff88011975ec00: fb fb fb fb fb fb fb fb fb fb fb fb
fb fb fb fb
[ 53.805979] >ffff88011975ec80: fb fb fb fb fb fb fb fb fb fb fb fb
fb fb fb fb
[ 53.806577] ^
[ 53.807165] ffff88011975ed00: fb fb fb fb fb fb fb fb fb fb fb fb
fb fb fb fb
[ 53.807762] ffff88011975ed80: fb fb fb fb fb fb fb fb fb fb fb fb
fb fb fb fb
[ 53.808356] ==================================================================
[ 53.808949] Disabling lock debugging due to kernel taint
Fixes: 6c8702c60b88 ("ipv6: sr: add support for SRH encapsulation and injection with lwtunnels")
Signed-off-by: David Lebrun <dlebrun@google.com>
Signed-off-by: Mathieu Xhonneux <m.xhonneux@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Christophe Roullier says:
====================
net: ethernet: stmmac: add support for stm32mp1
Patches to have Ethernet support on stm32mp1
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch describes syscon DT bindings.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Manage dwmac-4.20a version from synopsys
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add description for Ethernet MPU families fields
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Glue codes to support stm32mp157c device and stay
compatible with stm32 mcu familly
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to add a documentation for ptp_qoriq dt-bindings.
The description for ptp_qoriq dt-bindings was actually moved
from Documentation/devicetree/bindings/net/fsl-tsec-phy.txt,
since gianfar_ptp driver was moved to ptp_qoriq driver.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Global variable gfar_phc_index was used to get and store
phc index through gianfar_ptp driver. However gianfar_ptp
had been renamed as ptp_qoriq for QorIQ common PTP driver.
This gfar_phc_index doesn't work any more, and the phc index
is stored in drvdata now. This patch is to support getting
phc index through ptp_qoriq drvdata.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to move some definitions in ptp_qoriq.c
to the header file.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gianfar_ptp was the PTP clock driver for 1588 timer
module of Freescale QorIQ eTSEC (Enhanced Three-Speed
Ethernet Controllers) platforms. Actually QorIQ DPAA
(Data Path Acceleration Architecture) platforms is
also using the same 1588 timer module in hardware.
This patch is to rework gianfar_ptp as QorIQ common
PTP driver to support both DPAA and eTSEC. Moved
gianfar_ptp.c to drivers/ptp/, renamed it as
ptp_qoriq.c, and renamed many variables. There were
not any function changes.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixup the checksum for CHECKSUM_COMPLETE when pulling skbs on RX path.
Otherwise we get splats when tc mirred is used to redirect packets to ifb.
Before fix:
nic: hw csum failure
Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add RTL8211B suspend / resume callbacks.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sridhar Samudrala says:
====================
Enable virtio_net to act as a standby for a passthru device
The main motivation for this patch is to enable cloud service providers
to provide an accelerated datapath to virtio-net enabled VMs in a
transparent manner with no/minimal guest userspace changes. This also
enables hypervisor controlled live migration to be supported with VMs that
have direct attached SR-IOV VF devices.
Patch 1 introduces a failover module that provides a generic interface for
paravirtual drivers to listen for netdev register/unregister/link change
events from pci ethernet devices with the same MAC and takeover their
datapath. The notifier and event handling code is based on the existing
netvsc implementation.
Patch 2 refactors netvsc to use the registration/notification framework
introduced by failover module.
Patch 3 introduces a net_failover driver that provides an automated
failover mechanism to paravirtual drivers via APIs to create and destroy
a failover master netdev and mananges a primary and standby slave netdevs
that get registered via the generic failover infrastructure.
Patch 4 introduces a new feature bit VIRTIO_NET_F_STANDBY to virtio-net
that can be used by hypervisor to indicate that virtio_net interface
should act as a standby for another device with the same MAC address.
Patch 5 extends virtio_net to use alternate datapath when available and
registered. When STANDBY feature is enabled, virtio_net driver uese the
net_failover API to create an additional 'failover' netdev that acts as
a master device and controls 2 slave devices. The original virtio_net
netdev is registered as 'standby' netdev and a passthru/vf device with
the same MAC gets registered as 'primary' netdev. Both 'standby' and
'failover' netdevs are associated with the same 'pci' device. The user
accesses the network interface via 'failover' netdev. The 'failover'
netdev chooses 'primary' netdev as default for transmits when it is
available with link up and running.
As this patch series is initially focusing on usecases where hypervisor
fully controls the VM networking and the guest is not expected to directly
configure any hardware settings, it doesn't expose all the ndo/ethtool ops
that are supported by virtio_net at this time. To support additional usecases,
it should be possible to enable additional ops later by caching the state
in failover netdev and replaying when the 'primary' netdev gets registered.
At the time of live migration, the hypervisor needs to unplug the VF device
from the guest on the source host and reset the MAC filter of the VF to
initiate failover of datapath to virtio before starting the migration. After
the migration is completed, the destination hypervisor sets the MAC filter
on the VF and plugs it back to the guest to switch over to VF datapath.
This patch is based on the discussion initiated by Jesse on this thread.
https://marc.info/?l=linux-virtualization&m=151189725224231&w=2
v12:
- Tested live migration with virtio-net/AVF(i40evf) configured in failover
mode while running iperf in background. Tried static ip and dhcp
configurations using 'network' scripts and Network Manager.
- Build tested netvsc module.
Updates:
- Extended generic failover module to do common functions like setting
FAILOVER_SLAVE flag, registering rx-handler and linking to upper dev in
the generic register/unregister handlers.
This required adding 3 additional failover ops pre_register, pre_unregister
and handle_frame. netvsc and net_failover drivers are updated to support
these ops.
v11:
- Split net_failover module into 2 components.
1. 'failover' module that provides generic failover infrastructure
to register a failover instance and listen for slave events.
2. 'net_failover' driver that provides APIs to create/destroy upper
netdev and supports 3-netdev model used by virtio-net.
- Added documentation
v10:
- fix net_failover_open() to update failover CARRIER correctly based on
standby and primary states.
- fix net_failover_handle_frame() to handle frames received on standby
when primary is present.
- replace netdev_upper_dev_link with netdev_master_upper_dev_link and
handle lower dev state changes.
- fix net_failver_create() and net_failover_register() interfaces to
use ERR_PTR and avoid arg **
- disable setting mac address when virtio-net in STANDBY mode
- document exported symbols
- added entry to MAINTAINERS file
v9:
Select NET_FAILOVER automatically when VIRTIO_NET/HYPERV_NET
are enabled. (stephen)
v8:
- Made the failover managment routines more robust by updating the feature
bits/other fields in the failover netdev when slave netdevs are
registered/unregistered. (mst)
- added support for handling vlans.
- Limited the changes in netvsc to only use the notifier/event/lookups
from the failover module. The slave register/unregister/link-change
handlers are only updated to use the getbymac routine to get the
upper netdev. There is no change in their functionality. (stephen)
- renamed structs/function/file names to use net_failover prefix. (mst)
v7
- Rename 'bypass/active/backup' terminology with 'failover/primary/standy'
(jiri, mst)
- re-arranged dev_open() and dev_set_mtu() calls in the register routines
so that they don't get called for 2-netdev model. (stephen)
- fixed select_queue() routine to do queue selection based on VF if it is
registered as primary. (stephen)
- minor bugfixes
v6 RFC:
Simplified virtio_net changes by moving all the ndo_ops of the
bypass_netdev and create/destroy of bypass_netdev to 'bypass' module.
avoided 2 phase registration(driver + instances).
introduced IFF_BYPASS/IFF_BYPASS_SLAVE dev->priv_flags
replaced mutex with a spinlock
v5 RFC:
Based on Jiri's comments, moved the common functionality to a 'bypass'
module so that the same notifier and event handlers to handle child
register/unregister/link change events can be shared between virtio_net
and netvsc.
Improved error handling based on Siwei's comments.
v4:
- Based on the review comments on the v3 version of the RFC patch and
Jakub's suggestion for the naming issue with 3 netdev solution,
proposed 3 netdev in-driver bonding solution for virtio-net.
v3 RFC:
- Introduced 3 netdev model and pointed out a couple of issues with
that model and proposed 2 netdev model to avoid these issues.
- Removed broadcast/multicast optimization and only use virtio as
backup path when VF is unplugged.
v2 RFC:
- Changed VIRTIO_NET_F_MASTER to VIRTIO_NET_F_BACKUP (mst)
- made a small change to the virtio-net xmit path to only use VF datapath
for unicasts. Broadcasts/multicasts use virtio datapath. This avoids
east-west broadcasts to go over the PCI link.
- added suppport for the feature bit in qemu
====================
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch enables virtio_net to switch over to a VF datapath when STANDBY
feature is enabled and a VF netdev is present with the same MAC address.
It allows live migration of a VM with a direct attached VF without the need
to setup a bond/team between a VF and virtio net device in the guest.
It uses the API that is exported by the net_failover driver to create and
and destroy a master failover netdev. When STANDBY feature is enabled, an
additional netdev(failover netdev) is created that acts as a master device
and tracks the state of the 2 lower netdevs. The original virtio_net netdev
is marked as 'standby' netdev and a passthru device with the same MAC is
registered as 'primary' netdev.
The hypervisor needs to unplug the VF device from the guest on the source
host and reset the MAC filter of the VF to initiate failover of datapath
to virtio before starting the migration. After the migration is completed,
the destination hypervisor sets the MAC filter on the VF and plugs it back
to the guest to switch over to VF datapath.
This patch is based on the discussion initiated by Jesse on this thread.
https://marc.info/?l=linux-virtualization&m=151189725224231&w=2
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This feature bit can be used by hypervisor to indicate virtio_net device to
act as a standby for another device with the same MAC address.
VIRTIO_NET_F_STANDBY is defined as bit 62 as it is a device feature bit.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The net_failover driver provides an automated failover mechanism via APIs
to create and destroy a failover master netdev and manages a primary and
standby slave netdevs that get registered via the generic failover
infrastructure.
The failover netdev acts a master device and controls 2 slave devices. The
original paravirtual interface gets registered as 'standby' slave netdev and
a passthru/vf device with the same MAC gets registered as 'primary' slave
netdev. Both 'standby' and 'failover' netdevs are associated with the same
'pci' device. The user accesses the network interface via 'failover' netdev.
The 'failover' netdev chooses 'primary' netdev as default for transmits when
it is available with link up and running.
This can be used by paravirtual drivers to enable an alternate low latency
datapath. It also enables hypervisor controlled live migration of a VM with
direct attached VF by failing over to the paravirtual datapath when the VF
is unplugged.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the registration/notification framework supported by the generic
failover infrastructure.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The failover module provides a generic interface for paravirtual drivers
to register a netdev and a set of ops with a failover instance. The ops
are used as event handlers that get called to handle netdev register/
unregister/link change/name change events on slave pci ethernet devices
with the same mac address as the failover netdev.
This enables paravirtual drivers to use a VF as an accelerated low latency
datapath. It also allows migration of VMs with direct attached VFs by
failing over to the paravirtual datapath when the VF is unplugged.
Signed-off-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SCTP sockets originated in a VRF can improve their performance if CRC32c
computation is delegated to underlying devices: update device features,
setting NETIF_F_SCTP_CRC. Iterating the following command in the topology
proposed with [1],
# ip vrf exec vrf-h2 netperf -H 192.0.2.1 -t SCTP_STREAM -- -m 10K
the measured throughput in Mbit/s improved from 2395 ± 1% to 2720 ± 1%.
[1] https://www.spinics.net/lists/netdev/msg486007.html
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: David Ahern <dsa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some drivers, such as DWC EQOS on Tegra, need to perform operations that
can sleep under this lock (clk_set_rate() in tegra_eqos_fix_speed()) for
proper operation. Since there is no need for this lock to be a spinlock,
convert it to a mutex instead.
Fixes: e6ea2d16fc61 ("net: stmmac: dwc-qos: Add Tegra186 support")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Tested-by: Bhadram Varka <vbhadram@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tx-timeout mostly happens due to some issue in the device. In such cases,
debug dump would be helpful for identifying the cause of the issue.
This patch adds support to spill debug data during the Tx timeout. Here
bnx2x_panic_dump() API is used instead of bnx2x_panic(), since we still
want to allow the Tx-timeout recovery a chance to succeed.
Changes from previous version:
-------------------------------
v2: Fixed a coding error.
Please consider applying this to "net-next".
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the driver version to 12.0.0.4
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The driver exits port setup after failing the lpfc_sli4_get_parameters
command (messages 0356, 2541, & 1412).
The older CNA adapters do not support the MBX command. In the past
the code was allowed to fail and continue on with initialization.
However a nvme change moved a closing bracket and now makes all
failures terminal.
Revise the logic so that terminal failure only occurs if the command
failed on the newer adapters. Additionally, if parameters are set
that require information from the command and the command failed,
the parameters are erroneous and port set up should fail even on
the older adapters.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The lancer G5 chip family fails the CQ create with 16k page size. The
hardware incorrectly reports it supports large page sizes when it is
actually limited to 4k pages.
A prior patch resolved this for the A0 chip revision only. This patch
excludes all revisions of the G5 asic from using large page sizes. As
knowing the actual chip revision is unnecessary, the now unused definitions
are removed
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
modprobe -r lpfc produces the following:
Call Trace:
__blk_mq_run_hw_queue+0xa2/0xb0
__blk_mq_delay_run_hw_queue+0x9d/0xb0
? blk_mq_hctx_has_pending+0x32/0x80
blk_mq_run_hw_queue+0x50/0xd0
blk_mq_sched_insert_request+0x110/0x1b0
blk_execute_rq_nowait+0x76/0x180
nvme_keep_alive_work+0x8a/0xd0 [nvme_core]
process_one_work+0x17f/0x440
worker_thread+0x126/0x3c0
? manage_workers.isra.24+0x2a0/0x2a0
kthread+0xd1/0xe0
? insert_kthread_work+0x40/0x40
ret_from_fork_nospec_begin+0x21/0x21
? insert_kthread_work+0x40/0x40
However, rmmod lpfc would run correctly.
When an nvme remoteport is unregistered with the host nvme transport, it
needs to set the remoteport->dev_loss_tmo value 0 to indicate an immediate
termination of device loss and prevent any further keep alives to that
rport. The driver was never setting dev_loss_tmo causing the nvme
transport to continue to send the keep alive.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Under large configurations, the driver would start to log message 6065 -
NVME out of buffers (exchanges).
The driver is using the ndlp cmd_qdepth value when determining the max
outstanding ios for an adapter. This value, by default, is set to 65536,
which exceeds the maximum exchange counts supported on an adapter. The ndlp
cmd_qdepth has no relevance and outstanding io count should be capped at
the max exchange count with IO requests beyond that level getting bounced
back with an EBUSY status so that they are retried by the block layer.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
MDS diagnostics fail because of frame count mismatch.
Unavailability of SGL is the trigger for this issue. If ELS SGL is not
available to process MDS frame, IOCB is put in FCP txq but not attempted to
post afterwards. So, driver stops processing incoming frames as it runs out
of IOCB. lpfc_drain_txq attempts to submit IOCBS that are queued in ELS
txq but MDS frames are posted to FCP WQ.
Attempt to submit IOCBs that are present in FCP txq when MDS loopback is
running.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
When issuing a nexus reset for directly attached device, we want to ignore
the PHY down events so libsas will not deform and reform the port.
In the case that the attached SAS changes for the reset, libsas will deform
and form a port.
For scenario that the PHY does not come up after a timeout period, then
report the PHY down to libsas.
Signed-off-by: Xiang Chen <chenxiang66@hisilicon.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
It is an step of executing task to get free slot. If the step fails, we
will cleanup LLDD resources and should return failure to upper layer or
internal caller to abort task execution of this time.
But in the current code, the caller of get_free_slot() doesn't return
failure when get_free_slot() failed. This patch is to fix it.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
For v2 hw, STP link from target is rejected after host reset because of a
SoC bug. The STP reject will be terminated after we have sent IO from each
PHY of a port.
This is not an problem before, as we don't need to setup STP link from
target immediately after host reset. But now, it is. Because we want to
send soft-reset immediately after host reset.
In order to terminate STP reject quickly, this patch send ATA reset command
through each PHY of a port. Notes: ATA reset command don't need target's
response.
Besides, we do abort dev for each device before terminating STP reject.
This is a quirk of v2 hw.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This patch adds a force PHY function for internal ATA command for v2 hw.
Because there is an SoC bug in v2 hw, and need send an IO through each PHY
of a port to work around a bug which occurs after a controller reset.
This force PHY function will be used in the later patch.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
In future scenarios we will want to use the TMF struct for more task types
than SSP.
As such, we can add struct hisi_sas_tmf_task directly into struct
hisi_sas_slot, and this will mean we can remove the TMF parameters from the
task prep functions.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
