| Age | Commit message (Collapse) | Author |
|---|
|
In file included from ./include/linux/hugetlb.h:445:0,
from arch/powerpc/kernel/setup-common.c:37:
./arch/powerpc/include/asm/hugetlb.h: In function ‘huge_ptep_clear_flush’:
./arch/powerpc/include/asm/hugetlb.h:154:8: error: variable ‘pte’ set but not used [-Werror=unused-but-set-variable]
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
This patch implements CONFIG_DEBUG_VIRTUAL to warn about
incorrect use of virt_to_phys() and page_to_phys()
Below is the result of test_debug_virtual:
[ 1.438746] WARNING: CPU: 0 PID: 1 at ./arch/powerpc/include/asm/io.h:808 test_debug_virtual_init+0x3c/0xd4
[ 1.448156] CPU: 0 PID: 1 Comm: swapper Not tainted 4.20.0-rc5-00560-g6bfb52e23a00-dirty #532
[ 1.457259] NIP: c066c550 LR: c0650ccc CTR: c066c514
[ 1.462257] REGS: c900bdb0 TRAP: 0700 Not tainted (4.20.0-rc5-00560-g6bfb52e23a00-dirty)
[ 1.471184] MSR: 00029032 <EE,ME,IR,DR,RI> CR: 48000422 XER: 20000000
[ 1.477811]
[ 1.477811] GPR00: c0650ccc c900be60 c60d0000 00000000 006000c0 c9000000 00009032 c7fa0020
[ 1.477811] GPR08: 00002400 00000001 09000000 00000000 c07b5d04 00000000 c00037d8 00000000
[ 1.477811] GPR16: 00000000 00000000 00000000 00000000 c0760000 c0740000 00000092 c0685bb0
[ 1.477811] GPR24: c065042c c068a734 c0685b8c 00000006 00000000 c0760000 c075c3c0 ffffffff
[ 1.512711] NIP [c066c550] test_debug_virtual_init+0x3c/0xd4
[ 1.518315] LR [c0650ccc] do_one_initcall+0x8c/0x1cc
[ 1.523163] Call Trace:
[ 1.525595] [c900be60] [c0567340] 0xc0567340 (unreliable)
[ 1.530954] [c900be90] [c0650ccc] do_one_initcall+0x8c/0x1cc
[ 1.536551] [c900bef0] [c0651000] kernel_init_freeable+0x1f4/0x2cc
[ 1.542658] [c900bf30] [c00037ec] kernel_init+0x14/0x110
[ 1.547913] [c900bf40] [c000e1d0] ret_from_kernel_thread+0x14/0x1c
[ 1.553971] Instruction dump:
[ 1.556909] 3ca50100 bfa10024 54a5000e 3fa0c076 7c0802a6 3d454000 813dc204 554893be
[ 1.564566] 7d294010 7d294910 90010034 39290001 <0f090000> 7c3e0b78 955e0008 3fe0c062
[ 1.572425] ---[ end trace 6f6984225b280ad6 ]---
[ 1.577467] PA: 0x09000000 for VA: 0xc9000000
[ 1.581799] PA: 0x061e8f50 for VA: 0xc61e8f50
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Include the new USB product ID for Intel Bluetooth device 22260
family(CcPeak)
The /sys/kernel/debug/usb/devices portion for this device is:
T: Bus=01 Lev=01 Prnt=01 Port=02 Cnt=02 Dev#= 2 Spd=12 MxCh= 0
D: Ver= 2.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=8087 ProdID=0029 Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 64 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
I: If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 63 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 63 Ivl=1ms
Signed-off-by: Raghuram Hegde <raghuram.hegde@intel.com>
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Alexei Starovoitov says:
====================
pull-request: bpf 2018-12-18
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) promote bpf_perf_event.h to mandatory UAPI header, from Masahiro.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After phy_start() phylib takes care of all needed actions, including
aneg settings and checking link state. There's no need to set state
PHY_CHANGELINK in drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
clcsock can be released while kernel_accept() references it in TCP
listen worker. Also, clcsock needs to wake up before released if TCP
fallback is used and the clcsock is blocked by accept. Add a lock to
safely release clcsock and call kernel_sock_shutdown() to wake up
clcsock from accept in smc_release().
Reported-by: syzbot+0bf2e01269f1274b4b03@syzkaller.appspotmail.com
Reported-by: syzbot+e3132895630f957306bc@syzkaller.appspotmail.com
Signed-off-by: Myungho Jung <mhjungk@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently variable data0 is not being initialized so a garbage value is
being passed to vxge_hw_vpath_fw_api and this value is being written to
the rts_access_steer_data0 register. There are other occurrances where
data0 is being initialized to zero (e.g. in function
vxge_hw_upgrade_read_version) so I think it makes sense to ensure data0
is initialized likewise to 0.
Detected by CoverityScan, CID#140696 ("Uninitialized scalar variable")
Fixes: 8424e00dfd52 ("vxge: serialize access to steering control register")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At least old Xen net backends seem to send frags with no real data
sometimes. In case such a fragment happens to occur with the frag limit
already reached the frontend will BUG currently even if this situation
is easily recoverable.
Modify the BUG_ON() condition accordingly.
Tested-by: Dietmar Hahn <dietmar.hahn@ts.fujitsu.com>
Signed-off-by: Juergen Gross <jgross@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Microsemi has been bought by Microchip and Microchip is supporting those
switches.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Woojung Huh <Woojung.Huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NAME_DISTRIBUTOR messages are transmitted through unicast link on TIPC
2.0, by contrast, the messages are delivered through broadcast link on
TIPC 1.7. But at present, NAME_DISTRIBUTOR messages received by
broadcast link cannot be handled in tipc_rcv() until an unicast message
arrives, which may lead to a significant delay to update name table.
To avoid this delay, we will also deal with broadcast NAME_DISTRIBUTOR
message on broadcast receive path.
Signed-off-by: Zhenbo Gao <zhenbo.gao@windriver.com>
Reviewed-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Even though the link is down before entering hibernation,
there is an issue that the network interface always links up after resuming
from hibernation.
If the link is still down before enabling the network interface,
and after resuming from hibernation, the phydev->state is forcibly set
to PHY_UP in mdio_bus_phy_restore(), and the link becomes up.
In suspend sequence, only if the PHY is attached, mdio_bus_phy_suspend()
calls phy_stop_machine(), and mdio_bus_phy_resume() calls
phy_start_machine().
In resume sequence, it's enough to do the same as mdio_bus_phy_resume()
because the state has been preserved.
This patch fixes the issue by calling phy_start_machine() in
mdio_bus_phy_restore() in the same way as mdio_bus_phy_resume().
Fixes: bc87922ff59d ("phy: Move PHY PM operations into phy_device")
Suggested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current state for the lan78xx driver does not allow for changing the
MAC address of the interface, without either removing the module (if
you compiled it that way) or rebooting the machine. If you attempt to
change the MAC address, ifconfig will show the new address, however,
the system/interface will not respond to any traffic using that
configuration. A few short-term options to work around this are to
unload the module and reload it with the new MAC address, change the
interface to "promisc", or reboot with the correct configuration to
change the MAC.
This patch enables the ability to change the MAC address via fairly normal means...
ifdown <interface>
modify entry in /etc/network/interfaces OR a similar method
ifup <interface>
Then test via any network communication, such as ICMP requests to gateway.
My only test platform for this patch has been a raspberry pi model 3b+.
Signed-off-by: Jason Martinsen <jasonmartinsen@msn.com>
-----
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
3c1bcc8614db ("net: ethernet: Convert phydev advertize and supported
from u32 to link mode") left some unused code in phy_probe(), remove it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The LAN7431 uses an external phy, and it can be found anywhere in
the phy address space. This patch uses phy address 1 for LAN7430
only. And searches all addresses otherwise.
Signed-off-by: Bryan Whitehead <Bryan.Whitehead@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Petr Machata says:
====================
vxlan: Various fixes
This patch set contains three fixes for the vxlan driver.
Patch #1 fixes handling of offload mark on replaced VXLAN FDB entries. A
way to trigger this is to replace the FDB entry with one that can not be
offloaded. A future patch set should make it possible to veto such FDB
changes. However the FDB might still fail to be offloaded due to another
issue, and the offload mark should reflect that.
Patch #2 fixes problems in __vxlan_dev_create() when a call to
rtnl_configure_link() fails. These failures would be tricky to hit on a
real system, the most likely vector is through an error in vxlan_open().
However, with the abovementioned vetoing patchset, vetoing the created
entry would trigger the same problems (and be easier to reproduce).
Patch #3 fixes a problem in vxlan_changelink(). In situations where the
default remote configured in the FDB table (if any) does not exactly
match the remote address configured at the VXLAN device, changing the
remote address breaks the default FDB entry. Patch #4 is then a self
test for this issue.
v3:
- Patch #2:
- Reuse the same errout block for both cleanup paths. Use a bool to
decide whether the unregister_netdevice() call should be made.
v2:
- Drop former patch #3
- Patch #2:
- Delete the default entry before calling unregister_netdevice(). That
takes care of former patch #3, hence tweak the commit message to
mention that problem as well.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a test to exercise the fix from the previous patch.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Default remotes are stored as FDB entries with an Ethernet address of
00:00:00:00:00:00. When a request is made to change a remote address of
a VXLAN device, vxlan_changelink() first deletes the existing default
remote, and then creates a new FDB entry.
This works well as long as the list of default remotes matches exactly
the configuration of a VXLAN remote address. Thus when the VXLAN device
has a remote of X, there should be exactly one default remote FDB entry
X. If the VXLAN device has no remote address, there should be no such
entry.
Besides using "ip link set", it is possible to manipulate the list of
default remotes by using the "bridge fdb". It is therefore easy to break
the above condition. Under such circumstances, the __vxlan_fdb_delete()
call doesn't delete the FDB entry itself, but just one remote. The
following vxlan_fdb_create() then creates a new FDB entry, leading to a
situation where two entries exist for the address 00:00:00:00:00:00,
each with a different subset of default remotes.
An even more obvious breakage rooted in the same cause can be observed
when a remote address is configured for a VXLAN device that did not have
one before. In that case vxlan_changelink() doesn't remove any remote,
and just creates a new FDB entry for the new address:
$ ip link add name vx up type vxlan id 2000 dstport 4789
$ bridge fdb ap dev vx 00:00:00:00:00:00 dst 192.0.2.20 self permanent
$ bridge fdb ap dev vx 00:00:00:00:00:00 dst 192.0.2.30 self permanent
$ ip link set dev vx type vxlan remote 192.0.2.30
$ bridge fdb sh dev vx | grep 00:00:00:00:00:00
00:00:00:00:00:00 dst 192.0.2.30 self permanent <- new entry, 1 rdst
00:00:00:00:00:00 dst 192.0.2.20 self permanent <- orig. entry, 2 rdsts
00:00:00:00:00:00 dst 192.0.2.30 self permanent
To fix this, instead of calling vxlan_fdb_create() directly, defer to
vxlan_fdb_update(). That has logic to handle the duplicates properly.
Additionally, it also handles notifications, so drop that call from
changelink as well.
Fixes: 0241b836732f ("vxlan: fix default fdb entry netlink notify ordering during netdev create")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a failure occurs in rtnl_configure_link(), the current code
calls unregister_netdevice() to roll back the earlier call to
register_netdevice(), and jumps to errout, which calls
vxlan_fdb_destroy().
However unregister_netdevice() calls transitively ndo_uninit, which is
vxlan_uninit(), and that already takes care of deleting the default FDB
entry by calling vxlan_fdb_delete_default(). Since the entry added
earlier in __vxlan_dev_create() is exactly the default entry, the
cleanup code in the errout block always leads to double free and thus a
panic.
Besides, since vxlan_fdb_delete_default() always destroys the FDB entry
with notification enabled, the deletion of the default entry is notified
even before the addition was notified.
Instead, move the unregister_netdevice() call after the manual destroy,
which solves both problems.
Fixes: 0241b836732f ("vxlan: fix default fdb entry netlink notify ordering during netdev create")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When rdst of an offloaded FDB entry is replaced, it certainly isn't
offloaded anymore. Drivers are notified about such replacements, and can
re-mark the entry as offloaded again if they so wish. However until a
driver does so explicitly, assume a replaced FDB entry is not offloaded.
Note that replaces coming via vxlan_fdb_external_learn_add() are always
immediately followed by an explicit offload marking.
Fixes: 0efe11733356 ("vxlan: Support marking RDSTs as offloaded")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed:
====================
mlx5-uplink-rep-2018-12-15
Or Gerlitz says:
This series is essentially a cleanup to align with the rest of the NIC
switchdev drivers and make us
more robust and clear/n: currently the PF netdev serves as the mlx5
e-switch uplink netdev
representor when going into switchdev mode and back as plain NIC
netdev when going out.
This causes some irregularities and misc troubles.
Move to use dedicated uplink rep, as we have for the VF vports.
The uplink rep netdev does has sysfs link and supports the sriov vf
mac ndo, these two are in
use by libvirt and other orchestrators, It also has richer ethtool
support to allow controlling the
port link & mtu along with supporting dcb and plugging into the mlx5
lag logic.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Anssi Hannula says:
====================
net: macb: DMA race condition fixes
Here are a couple of race condition fixes for the macb driver. The first
two are for issues observed at runtime on real HW.
v2:
- added received Tested-bys and Acked-bys to the first two patches
- in patch 3/3, moved the timestamp protection barrier closer to the
timestamp reads
- in patch 3/3, removed unnecessary move of the addr assignment in
gem_rx() to keep the patch minimal for maximum clarity
- in patch 3/3, clarified commit message and comments
The 3/3 is the same one I improperly sent last week as a standalone
patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When reading buffer descriptors on RX or on TX completion, an
RX_USED/TX_USED bit is checked first to ensure that the descriptors have
been populated, i.e. the ownership has been transferred. However, there
are no memory barriers to ensure that the data protected by the
RX_USED/TX_USED bit is up-to-date with respect to that bit.
Specifically:
- TX timestamp descriptors may be loaded before ctrl is loaded for the
TX_USED check, which is racy as the descriptors may be updated between
the loads, causing old timestamp descriptor data to be used.
- RX ctrl may be loaded before addr is loaded for the RX_USED check,
which is racy as a new frame may be written between the loads, causing
old ctrl descriptor data to be used.
This issue exists for both macb_rx() and gem_rx() variants.
Fix the races by adding DMA read memory barriers on those paths and
reordering the reads in macb_rx().
I have not observed any actual problems in practice caused by these
being missing, though.
Tested on a ZynqMP based system.
Fixes: 89e5785fc8a6 ("[PATCH] Atmel MACB ethernet driver")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bit RX_USED set to 0 in the address field allows the controller to write
data to the receive buffer descriptor.
The driver does not ensure the ctrl field is ready (cleared) when the
controller sees the RX_USED=0 written by the driver. The ctrl field might
only be cleared after the controller has already updated it according to
a newly received frame, causing the frame to be discarded in gem_rx() due
to unexpected ctrl field contents.
A message is logged when the above scenario occurs:
macb ff0b0000.ethernet eth0: not whole frame pointed by descriptor
Fix the issue by ensuring that when the controller sees RX_USED=0 the
ctrl field is already cleared.
This issue was observed on a ZynqMP based system.
Fixes: 4df95131ea80 ("net/macb: change RX path for GEM")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
64-bit DMA addresses are split in upper and lower halves that are
written in separate fields on GEM. For RX, bit 0 of the address is used
as the ownership bit (RX_USED). When the RX_USED bit is unset the
controller is allowed to write data to the buffer.
The driver does not guarantee that the controller already sees the upper
half when the RX_USED bit is cleared, possibly resulting in the
controller writing an incoming frame to an address with an incorrect
upper half and therefore possibly corrupting unrelated system memory.
Fix that by adding the necessary DMA memory barrier between the writes.
This corruption was observed on a ZynqMP based system.
Fixes: fff8019a08b6 ("net: macb: Add 64 bit addressing support for GEM")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Acked-by: Harini Katakam <harini.katakam@xilinx.com>
Tested-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Herton reports the following error when building a userspace program that
includes net_stamp.h:
In file included from foo.c:2:
/usr/include/linux/net_tstamp.h:158:2: error: unknown type name
‘clockid_t’
clockid_t clockid; /* reference clockid */
^~~~~~~~~
Fix it by using __kernel_clockid_t in place of clockid_t.
Fixes: 80b14dee2bea ("net: Add a new socket option for a future transmit time.")
Cc: Timothy Redaelli <tredaelli@redhat.com>
Reported-by: Herton R. Krzesinski <herton@redhat.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Tested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some platforms (currently detected only on SAMA5D4) TX might stuck
even the pachets are still present in DMA memories and TX start was
issued for them. This happens due to race condition between MACB driver
updating next TX buffer descriptor to be used and IP reading the same
descriptor. In such a case, the "TX USED BIT READ" interrupt is asserted.
GEM/MACB user guide specifies that if a "TX USED BIT READ" interrupt
is asserted TX must be restarted. Restart TX if used bit is read and
packets are present in software TX queue. Packets are removed from software
TX queue if TX was successful for them (see macb_tx_interrupt()).
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
function br_multicast_toggle now always return 0,
so the variable 'err' is unneeded.
Also cleanup dead branch in br_changelink.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1070:5: warning:
variable 'op' set but not used [-Wunused-but-set-variable]
drivers/net/ethernet/qlogic/qlcnic/qlcnic_sriov_pf.c:1342:5: warning:
variable 'cmd_op' set but not used [-Wunused-but-set-variable]
'op' never used since introduction in commit 7cb03b2347d5 ("qlcnic:
Support VF-PF communication channel commands.")
'cmd_op' not used since commit 6226204bcf20 ("qlcnic: Fix operation
type and command type.")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On many devices the RTL8723BS device gets reset during suspend/resume,
causing it to lose its firmware and all state.
Testing has shown it drops back to communicating at 115200 bps and sends
sync-request packages, indicating it has been fully reset.
This commit fixes this by queueing a reprobe on resume.
This mirrors how USB RTL BT devices, which have the same problem, are
handled in the btusb driver, there we set the USB_QUIRK_RESET_RESUME for
all RTL devices, which also causes a reprobe on resume. The only difference
is that here we need to do the reprobe ourselves.
Since we are doing a full reprobe on resume now, we can also turn off the
device on suspend to save power while suspended.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add support for vendor specific suspend / resume callbacks.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Current btf internal verbose logger logs fwd type as
[2] FWD A type_id=0
where A is the type name.
Commit 9d5f9f701b18 ("bpf: btf: fix struct/union/fwd types
with kind_flag") introduced kind_flag which can be used
to distinguish whether a forward type is a struct or
union.
Also, "type_id=0" does not carry any meaningful
information for fwd type as btf_type.type = 0 is simply
enforced during btf verification and is not used
anywhere else.
This commit changed the log to
[2] FWD A struct
if kind_flag = 0, or
[2] FWD A union
if kind_flag = 1.
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
Pull block fix from Jens Axboe:
"Correct an ioctl direction for the zoned ioctls"
* tag 'for-linus-20181218' of git://git.kernel.dk/linux-block:
uapi: linux/blkzoned.h: fix BLKGETZONESZ and BLKGETNRZONES definitions
|
|
Trivial fix to clean up an indentation issue, remove spaces
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fix from Bjorn Helgaas:
"Fix the ACPI APEI error path, which previously queued several
uninitialized events (Yanjiang Jin)"
* tag 'pci-v4.20-fixes-4' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI/AER: Queue one GHES event, not several uninitialized ones
|
|
The function should return an error if create_singlethread_workqueue()
fails.
Fixes: 34877a15f787 ("net: stmmac: Rework and fix TX Timeout code")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to commit 143ece654f9f ("tipc: check tsk->group in tipc_wait_for_cond()")
we have to reload grp->dests too after we re-take the sock lock.
This means we need to move the dsts check after tipc_wait_for_cond()
too.
Fixes: 75da2163dbb6 ("tipc: introduce communication groups")
Reported-and-tested-by: syzbot+99f20222fc5018d2b97a@syzkaller.appspotmail.com
Cc: Ying Xue <ying.xue@windriver.com>
Cc: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial fix to clean up an indentation issue
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
We accidentally deleted the code to set "rc = -ENOMEM;" and this patch
adds it back.
Fixes: d2201a21598a ("qed: No need for LL2 frags indication")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HCI_QUIRK_RESET_ON_CLOSE quirk is required for BT v1.0 based devices,
to send a reset command to the chip during hci device close. Serdev
architecture is used for the latest BT chips, which doesn't require to
send the reset command during close. If still chips required reset
command during close, it would be better enabling it in the vendor
probes or in proto setup.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The barriers are redundant because atomic_test_and_clear_bit() already
provides the required full ordering for the cases in question (that is,
when the bit is cleared).
Signed-off-by: Andrea Parri <andrea.parri@amarulasolutions.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
John Fastabend says:
====================
This adds a size field to the sk_msg_md data structure used by SK_MSG
programs. Without this in the zerocopy case and in the copy case
where multiple iovs are in use its difficult to know how much data
can be pulled in. The normal method of reading data and data_end
only give the current contiguous buffer. BPF programs can attempt to
pull in extra data but have to guess if it exists. This can result
in multiple "guesses" its much better if we know upfront the size
of the sk_msg.
====================
Acked-by: Martin KaFai Lau <kafai@fb.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
The BCM43430A0 has the default MAC address 43:43:A0:12:1F:AC if none
is given. This address was found when enabling Bluetooth on a bunch of
boards with the AMPAK AP6210 module, all sharing the same address. It
also contains the sequence 4343A0, which is suspicious as that is also
the name the chip identifies itself as.
Add this to the list of default MAC addresses and leave it to the user
to configure a valid one.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The BCM4330 chip is a 802.11 a/b/g/n + Bluetooth 4.0 + HS controller.
This patch adds a compatible string match to the serdev driver for the
Bluetooth part of the chip.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The BCM20702A1 chip is a single-chip Bluetooth 4.0 controller and
transceiver. It is found in the AMPAK AP6210 WiFi+BT package.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The datasheets for BCM20702 and BCM43438 both have power up time
sequence graphs, however they are slightly different. Both chips
also have an internal power-on-reset, which holds the chip in reset
for a short time after the regulators are enabled.
For the BCM20702, the time period from when the regulators are enabled,
until the chip settles and comes out of sleep state, is 6564 ~ 8171 us.
For the BCM43438, the graph only shows the time period from when the
regulators are enabled until the chip responds by driving the host's
CTS line low, assuming the host has already driven its RTS line low.
This is shown to be 6.5 sleep cycles, with the sleep clock at 32.768
kHz. This is around 2 ms.
Wait a full 10 ms after the regulators are enabled to account for signal
rising times.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The Broadcom Bluetooth chips have two power inputs, VBAT and VDDIO.
The former provides overall power for the chip, while the latter powers
the I/O pins and buffers.
Model these two as regulator supplies, and let the driver manage them
in the same way as it does the clock supply.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The Broadcom Bluetooth controllers support a secondary LPO clock at
32.768 kHz. This external clock provides low power timing, and also
a way to detect the frequency of the main reference clock. On many
designs without NVRAM and a non-default reference clock, this must
be used or the controller will not function correctly.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Originally the device tree binding only specified one clock reference,
with the name "extclk". The driver simply retrieves the clock without
bothering to specify a name.
Since we added a second clock to the binding, we need to fetch the
clocks by name now. First we try the new name "txco", then fall back
to the old name "extclk", and finally try retrieving a clock without
using any name, to cover any instances where a bad device tree or
firmware worked by accident.
In the last case, we should take care that we don't get the same
clock twice when we add support for the "lpo" clock.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The driver currently checks the clk pointer for an error condition, as
returned by clk_get, before every invocation of the clk consumer API.
This is redundant if the goal is simply to ignore the errors, thereby
making the clk optional. The clk consumer API already checks if the
pointer is NULL or not.
Simplify the code a bit by assigning NULL to the clk pointer if the
error condition is one we want to ignore, which is every error except
deferred probing.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
On some systems that actually have the bluetooth controller wired up
with an extra clock signal, it's possible the bluetooth controller
probes before the clock provider. clk_get would return a defer probe
error, which was not handled by this driver.
Handle this properly, so that these systems can work reliably.
Tested-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
