| Age | Commit message (Collapse) | Author |
|---|
|
This command is buggy (doesn't take the mutex) and unused. Instead, the
"start_recovery" file is used for the same purpose. Remove the code but
keep the command constant to avoid breaking the testmode ABI.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
If a Tx queue is currently stopped because of our Tx watermark flow
control, don't stop it again. This causes a warning to appear.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
Refuse to boot if the FW version is too old. The minimum version is set
per chip, with the option of setting it per PG in the future.
When boot fails because of an old FW, display a helpful message.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
New wl12xx firmware supports scheduled scans also while connected.
Stop blocking sched scan requests when connected and add a quirk to
block in hardware that don't support it (currently wl18xx doesn't).
This requires FW version 6/7.3.10.2.112 for single-role and
6/7.5.6.0.25 for multi-role.
Signed-off-by: Victor Goldenshtein <victorg@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/newsoc
From Tony Lindgren <tony@atomide.com>:
This branch contains minimal support for omap5 to boot to a
console without clock framework support. This branch depends
on omap-cleanup-part2-for-v3.6.
* 'devel-omap5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: Kconfig update to support additional GPIOs in OMAP5
ARM: OMAP5: Add the build support
arm/dts: OMAP5: Add omap5 dts files
ARM: OMAP5: board-generic: Add device tree support
ARM: omap2+: board-generic: clean up the irq data from board file
ARM: OMAP5: Add SMP support
ARM: OMAP5: Add the WakeupGen IP updates
ARM: OMAP5: l3: Add l3 error handler support for omap5
ARM: OMAP5: gpmc: Update gpmc_init()
ARM: OMAP5: timer: Add clocksource, clockevent support
ARM: OMAP5: Add minimal support for OMAP5430 SOC
ARM: OMAP5: id: Add cpu id for ES versions
ARM: OMAP: counter-32k: Select the CR register offset using the IP scheme
ARM: OMAP2+: Move stubbed secure_sram_reserve function to a common.c and call it __weak
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Dependency for omap/minimal-omap5
|
|
ieee802_1d_to_ac is defined as a const int[8],
but the tid parameter has a range from 0 to 15.
Cc: stable@vger.kernel.org
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
The HCP message should be added to transmit queue, not the other way around.
Signed-off-by: Mathias Jeppsson <mathias.jeppsson@sonymobile.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
list_first_entry() will never return NULL. Instead use
list_for_each_entry_safe() to iterate through the list.
Signed-off-by: Mathias Jeppsson <mathias.jeppsson@sonymobile.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/clk
From Tony Lindgren <tony@atomide.com>:
This branch adds clock data for am33xx. Note that eventually these
will use the common clock framework, but those patches are not quite
ready yet for omaps. This branch depends on omap-cleanup-part2-for-v3.6
branch.
* tag 'omap-devel-am33xx-data-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3+: clock33xx: Add AM33XX clock tree data
ARM: OMAP3+: clock: Move common clksel_rate & clock data to common file
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Dependency for omap/am33xx-clk branch
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup2
From Tony Lindgren <tony@atomide.com>:
This branch contains more clean-up like changes and minor fixes for making
it easier to support new omap SoCs, such as omap5 and am33xx.
This branch has dependencies to earlier clean-up in omap-cleanup-for-v3.6
and omap-devel-dmtimer-for-v3.6 branches, and also depends on the
omap-devel-am33xx-for-v3.6 branch, and are based on a merge of these
branches.
* tag 'omap-cleanup-part2-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: sdrc: Fix the build break for OMAP4 only builds
ARM: OMAP2+: dmtimer: cleanup fclk usage
ARM: OMAP2+: Fix mismerge for omap_hwmod_get_main_clk() API
ARM: OMAP2+: Remove unnecessary ifdef around __omap2_set_globals
ARM: OMAP2+: am33xx: Change cpu_is_am33xx to soc_is_am33xx
ARM: OMAP2+: am33xx: Make am33xx as a separate class
ARM: OMAP2+: Move omap3 dpll ops to dpll3xxx.c
ARM: OMAP2+: All OMAP2PLUS uses omap-device.o target so add one entry
ARM: OMAP: dmtimer: use devm_ API and do some cleanup in probe()
ARM: OMAP2+: hwmod code: add support to set dmadisable in hwmod framework
ARM: OMAP2+: PRM/CM: Move the stubbed prm and cm functions to prcm.c file and make them __weak
ARM: OMAP2+: hwmod: add omap_hwmod_get_main_clk() API
ARM: OMAP3+: dpll: optimize noncore dpll locking logic
ARM: OMAP3: control: add definition for CONTROL_CAMERA_PHY_CTRL
ARM: OMAP2+: powerdomain code: Fix Wake-up power domain power status
ARM: OMAP4: clockdomain/CM code: Update supported transition modes
ARM: OMAP3/4: omap_hwmod: Add rstst_offs field to struct omap_hwmod_omap4_prcm
ARM: OMAP2+: hwmod: Add new sysc_type3 into omap_hwmod required for am33xx
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/boards
From Tony Lindgren <tony@atomide.com>:
Board and platform data related changes for omaps
* tag 'omap-devel-board-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: Fix omap3evm randconfig error introduced by VBUS support
ARM: OMAP: board-omap4panda: MUX configuration for sys_nirq2
ARM: OMAP: board-4430sdp: MUX configuration for sys_nirq2
ARM: OMAP3530evm: set pendown_state and debounce time for ads7846
ARM: omap3evm: enable VBUS switch for EHCI tranceiver
ARM: OMAP3EVM: Adding USB internal LDOs board file
ARM: OMAP3EVM: Add NAND flash definition
ARM: OMAP3: cm-t35: add tvp5150 decoder support
ARM: OMAP3: cm-t35: add mt9t001 camera sensor support
omap2+: add drm device
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://gitorious.org/linux-davinci/linux-davinci into next/fixes-non-critical
DaVinci fixes for v3.6
Fix an interrupt handling issue with cp_intc which
was causing occasional spurious interrupts with DA850 EVM
* tag 'davinci-v3.6-fixes' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: da8xx: fix interrupt handling
|
|
git://gitorious.org/linux-davinci/linux-davinci into next/soc
From Sekhar Nori <nsekhar@ti.com>:
DaVinci SoC updates for v3.6
Add IRQ domain support for cp_intc and
runtime PM core support for DaVinci devices.
* tag 'davinci-v3.6-soc' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: add runtime PM support for clock management
ARM: davinci: cp_intc: Add irq domain support
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://gitorious.org/linux-davinci/linux-davinci into next/cleanup
From: Sekhar Nori <nsekhar@ti.com>
DaVinci cleanups for v3.6
Remove some header files which were marked for removal. These files are
not used anymore.
* tag 'davinci-v3.6-cleanup' of git://gitorious.org/linux-davinci/linux-davinci:
ARM: davinci: remove dummy header files
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren <tony@atomide.com>:
Here is one PM regression fix and a defconfig change to disable
echi-omap because the driver currently causes issues with PM.
This annoys Kevin as it makes it harder for him to validate that
PM is working. The proper fixes for the echi-omap are being
discussed, but looks like it will not be properly working with PM
until in v3.7.
* tag 'omap-fixes-for-v3.5-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: omap2plus_defconfig: EHCI driver is not stable, disable it
ARM: OMAP2+: hwmod code/clockdomain data: fix 32K sync timer
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
From: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
You'll find in this patch set the nineth version of the initial
support for a new family of ARMv7-compatible Marvell SoCs.
As for the previous releases, both the Armada 370 and the Armada XP
SoCs are supported in this directory, and we are able to build a
single kernel image that boots on both SoCs. Both SoCs use the PJ4B
processor, a Marvell-developed ARM core that implements the ARMv7
instruction set. We are currently using Marvell evaluation boards for
both of those SoCs, and the support for those boards is added in this
patch set.
This patch set, and the support for those SoCs, started as a
collaborative effort from Marvell engineers (who have done the initial
development work) and Free Electrons engineers (who are reshaping the
code for mainline submission, adding device tree support, etc.). This
effort has also received contributions from Ben Dooks from Codethink.
* mvebu/newsoc:
ARM: mvebu: MPIC: read number of interrupts from control register
arm: mach-mvebu: add entry to MAINTAINERS
arm: mach-mvebu: add compilation/configuration change
arm: mach-mvebu: add defconfig
arm: mach-mvebu: add documentation for new device tree bindings
arm: mach-mvebu: add support for Armada 370 and Armada XP with DT
arm: mach-mvebu: add source files
arm: mach-mvebu: add header
clocksource: time-armada-370-xp: Marvell Armada 370/XP SoC timer driver
Changes from Arnd
* Pulled from git://github.com/Marvell-Semi/EBU_mainline_public.git mvebu_for-next-V9
* rebased onto v3.5-rc5 because it was originally based on
an old arm-soc/for-next branch
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
Read the number of MPIC interrupts from the controller and only register
that many.
[gregory.clement@free-electrons.com: rename armada symbol name to fit
with new name: armada_370_xp]
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Lior Amsalem <alior@marvell.com>
|
|
The new mach-mvebu directory will be maintained by Andrew Lunn and
Jason Cooper (as the existing maintainers for previous Marvell EBU
SoCs) together with Grégory Clément for the Armada 370/XP SoCs.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Lior Amsalem <alior@marvell.com>
|
|
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Lior Amsalem <alior@marvell.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Yehuda Yitschak <yehuday@marvell.com>
Tested-by: Lior Amsalem <alior@marvell.com>
|
|
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Lior Amsalem <alior@marvell.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Yehuda Yitschak <yehuday@marvell.com>
Tested-by: Lior Amsalem <alior@marvell.com>
|
|
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Lior Amsalem <alior@marvell.com>
Tested-by: Yehuda Yitschak <yehuday@marvell.com>
Tested-by: Lior Amsalem <alior@marvell.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
|
|
[ben.dooks@codethink.co.uk: ensure error check on of_property_read_u32]
[ben.dooks@codethink.co.uk: use mpic address instead of bus-unit's ]
[ben.dooks@codethink.co.uk: BUG_ON() if the of_iomap() fails for mpic]
[ben.dooks@codethink.co.uk: move mpic per-cpu register base ]
[ben.dooks@codethink.co.uk: number fetch should use irqd_to_hwirq()]
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Lior Amsalem <alior@marvell.com>
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Yehuda Yitschak <yehuday@marvell.com>
Tested-by: Lior Amsalem <alior@marvell.com>
|
|
[ben.dooks@codethink.co.uk: fixup style error in system-controller]
[ben.dooks@codethink.co.uk: check result of of_match_node()]
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Lior Amsalem <alior@marvell.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Yehuda Yitschak <yehuday@marvell.com>
Tested-by: Lior Amsalem <alior@marvell.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
|
|
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Lior Amsalem <alior@marvell.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Yehuda Yitschak <yehuday@marvell.com>
Tested-by: Lior Amsalem <alior@marvell.com>
|
|
Timer 0 is used as free-running clocksource, while timer 1 is used as
clock_event_device.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Lior Amsalem <alior@marvell.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Yehuda Yitschak <yehuday@marvell.com>
Tested-by: Lior Amsalem <alior@marvell.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: John Stultz <johnstul@us.ibm.com>
|
|
Add device tree nodes to enable ucc uart support on P1025RDB.
Signed-off-by: Zhicheng Fan <B32736@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/boards
From Kukjin Kim <kgene.kim@samsung.com>:
* 'next/board-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: S3C64XX: Add IRQ mapping for wm0010 on Cragganmore
ARM: S5PV210: Add HSOTG support to SMDKV210
ARM: EXYNOS: Update keypad entries for SMDK4X12
ARM: S3C64XX: Dynamically assign interrupts for CPU PMIC on Cragganmore
ARM: S3C64XX: Dynamically allocate the IRQ range for WM8994 on Cragganmore
ARM: S3C64XX: Add WM5102 EVM to Cragganmore modules
ARM: S3C64XX: Add module identification for Balblair Cragganmore module
ARM: EXYNOS: Add HSOTG support to SMDKV310
ARM: EXYNOS: Add HSOTG support to Origen
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dma
From Kukjin Kim <kgene.kim@samsung.com>:
Here is updating DMA common operation for Samsung SoCs.
Since some DMA client driver such as spi needs to change the configuration
after dma_request() so this branch adds dma_config() can configure DMA
transmit option which is included in dma_request() after that.
Note, according to the changes, needs to update spi and ASoC drivers
for Samsung SoCs and only got the ack from Mark Brown not Grant Likely
and as I know, he is busy for moving. But I think, the spi change has
no problem and it is simple.
* 'next/devel-dma-ops' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: SAMSUNG: Fix compiler warning in dma-ops.c file
ASoC: follow the updated samsung DMA common operations
spi/s3c64xx: Add the use of DMA config operation
ARM: SAMSUNG: Add config() function in DMA common operations
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/cleanup
From Kukjin Kim <kgene.kim@samsung.com>:
Samsung cleanup patches for v3.6 and most of them are removing
useless codes
* 'next/cleanup-samsung' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: EXYNOS: Remove the L2 cache latency setting for EXYNOS5
ARM: EXYNOS: Remove leftovers of the Samsung specific power domain control
ARM: SAMSUNG: Remove unused variable 'running' on PWM
ARM: SAMSUNG: remove unused SPI clock headers
ARM: S3C24XX: remove unused header <mach/bast-pmu.h>
ARM: S3C24XX: Remove duplicate header file inclusion
ARM: SAMSUNG: Remove description corresponding to a deleted element
ARM: S5PC100: Remove unused variable in dma.c file
ARM: S5P64X0: Remove unused variable in dma.c file
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Freescale PowerPC SoCs share a number of IP blocks with Freescale
ARM/IMX SoCs, FlexCAN, SSI, FEC, eSDHC, USB, etc. There are some
effort consolidating those drivers to make them work for both
architectures.
One outstanding difference between two architectures is ARM/IMX will
turn off module clocks during platform initialization for power saving
and expects drivers manage clocks using clk API, while PowerPC
mostly does not do that, and thus does not always build in clk API.
Listing all those driver Kconfig options in "select PPC_CLOCK if" seems
not scalable for long term maintenance, and could easily introduce
Kconfig recursive dependency. This patch chooses to select PPC_CLOCK
unconditionally for FSL_SOC to always build clk API for PowerPC in.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
QE Microcode Initialization using qe_upload_microcode() does not work on
P1021 if the IRAM-Ready register is not set after the microcode upload. Add
a definition for the "I-RAM Ready" register and sets it upon microcode
upload completion.
Signed-off-by: Ioannis Kokkoris <ioannis.kokoris@siemens-enterprise.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
With 2-cell format interrupts of MSI PCIe ethernet card can not work.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The issue log on core1 is:
root@mpc8572ds:~# ifconfig eth0 10.192.208.244
net eth0: could not attach to PHY
SIOCSIFFLAGS: No such device
To attach PHY node mdio@24520 should not be disabled in dts of core1.
Because all PHYs are controlled through this node as follows:
mdio@24520 {
phy0: ethernet-phy@0 {
interrupts = <10 1 0 0>;
reg = <0x0>;
};
phy1: ethernet-phy@1 {
interrupts = <10 1 0 0>;
reg = <0x1>;
};
phy2: ethernet-phy@2 {
interrupts = <10 1 0 0>;
reg = <0x2>;
};
phy3: ethernet-phy@3 {
interrupts = <10 1 0 0>;
reg = <0x3>;
};
tbi0: tbi-phy@11 {
reg = <0x11>;
device_type = "tbi-phy";
};
};
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jia Hongtao <B38951@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
CONFIG_FSL_BOOKE is only defined in 32-bit, CONFIG_PPC_FSL_BOOK3E is
defined in both 32-bit and 64-bit, so use CONFIG_PPC_FSL_BOOK3E to make
driver work in 32-bit & 64-bit.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
We should use the MPIC_LARG_VECTORS flag while intializing the MPIC.
This prevents us from eating in to hardware vector number space (MSIs)
while setting up internal sources.
Signed-off-by: Varun Sethi <Varun.Sethi@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
So that we can call it when improving SPE switch like book3e did for fp
switch.
Signed-off-by: Liu Yu <yu.liu@freescale.com>
Signed-off-by: Olivia Yin <hong-hua.yin@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
BSC9131RDB is a Freescale reference design board for BSC9131 SoC. The
BSC9131 is integrated SoC that targets Femto base station market. It
combines Power Architecture e500v2 and DSP StarCore SC3850 core
technologies with MAPLE-B2F baseband acceleration processing elements.
The BSC9131 SoC includes the following function and features:
. Power Architecture subsystem including a e500 processor with 256-Kbyte
shared L2 cache
. StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache
. The Multi Accelerator Platform Engine for Femto BaseStation Baseband
Processing (MAPLE-B2F)
. A multi-standard baseband algorithm accelerator for Channel
Decoding/Encoding, Fourier Transforms, UMTS chip rate processing, LTE
UP/DL Channel processing, and CRC algorithms
. Consists of accelerators for Convolution, Filtering, Turbo Encoding,
Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix
Inversion operations
. DDR3/3L memory interface with 32-bit data width without ECC and 16-bit
with ECC, up to 400-MHz clock/800 MHz data rate
. Dedicated security engine featuring trusted boot
. DMA controller
. OCNDMA with four bidirectional channels
. Interfaces
. Two triple-speed Gigabit Ethernet controllers featuring network
acceleration including IEEE 1588. v2 hardware support and
virtualization (eTSEC)
. eTSEC 1 supports RGMII/RMII
. eTSEC 2 supports RGMII
. High-speed USB 2.0 host and device controller with ULPI interface
. Enhanced secure digital (SD/MMC) host controller (eSDHC)
. Antenna interface controller (AIC), supporting three industry standard
JESD207/three custom ADI RF interfaces (two dual port and one single
port) and three MAXIM's MaxPHY serial interfaces
. ADI lanes support both full duplex FDD support and half duplex TDD
support
. Universal Subscriber Identity Module (USIM) interface that facilitates
communication to SIM cards or Eurochip pre-paid phone cards
. TDM with one TDM port
. Two DUART, four eSPI, and two I2C controllers
. Integrated Flash memory controller (IFC)
. TDM with 256 channels
. GPIO
. Sixteen 32-bit timers
The DSP portion of the SoC consists of DSP core (SC3850) and various
accelerators pertaining to DSP operations.
BSC9131RDB Overview
----------------------
BSC9131 SoC
1Gbyte DDR3 (on board DDR)
128Mbyte 2K page size NAND Flash
256 Kbit M24256 I2C EEPROM
128 Mbit SPI Flash memory
USB-ULPI
eTSEC1: Connected to RGMII PHY
eTSEC2: Connected to RGMII PHY
DUART interface: supports one UARTs up to 115200 bps for console display
Linux runs on e500v2 core and access some DSP peripherals like AIC
Signed-off-by: Ramneek Mehresh <ramneek.mehresh@freescale.com>
Signed-off-by: Priyanka Jain <Priyanka.Jain@freescale.com>
Signed-off-by: Akhil Goyal <Akhil.Goyal@freescale.com>
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Rajan Srivastava <rajan.srivastava@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This reverts commit 96cc017c5b7ec095ef047d3c1952b6b6bbf98943.
The P3060 was cancelled before it went into production, so there's no point
in supporting it.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
In order to enable the DIU video controller on the P1022DS, the FPGA needs
to be switched to "indirect mode", where the localbus is disabled and
the FPGA is accessed via writes to localbus chip select signals CS0 and CS1.
To obtain the address of CS0 and CS1, the platform driver uses an "indirect
pixis mode" device tree node. This node assumes that the localbus 'ranges'
property is sorted in chip-select order. That is, reg value 0 maps to
CS0, reg value 1 maps to CS1, etc. This is how the 'ranges' property is
supposed to be arranged.
Unfortunately, the 'ranges' property is often mis-arranged, and not just on
the P1022DS. Linux normally does not care, since it does not program the
localbus. But the indirect-mode code on the P1022DS does care.
The "proper" fix is to have U-Boot fix the 'ranges' property, but this would
be too cumbersome. The names and 'reg' properties of all the localbus
devices would also need to be updated, and determining which localbus device
maps to which chip select is board-specific.
Instead, we determine the CS0/CS1 base addresses the same way that U-boot
does -- by reading the BRx registers directly and mapping them to physical
addresses. This code is simpler and more reliable, and it does not require
a U-boot or device tree change.
Since the indirect pixis device tree node is no longer needed, the node is
deleted from the DTS.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
NAND on p2041 uses CS1 as chip select.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This reference board dates back to 2004, and is largely a legacy
EOL product. The MPC8560 is a pre e500v2 CPU. The SBC8548 is
a more modern, better e500v2 target for people to use as a
reference board with today's kernels, should they require one.
Removing support for it will also allow us to remove some
sbc8560 specific quirk handling in 8250 UART code, and some
MTD mapping support.
Cc: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
The p1024rdb has the similar feature as the p1020rdb. Therefore, p1024rdb use
the same platform file as the p1/p2 rdb board.
Overview of P2020RDB platform
- DDR3 1G
- NOR flash 16M
- 3 Ethernet interfaces
- NAND Flash 32M
- SPI EEPROM 16M
- SD/MMC
- 2 USB ports
- 4 TDM ports
Signed-off-by: Jin Qing <b24347@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Tang Yuantian <Yuantian.Tang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add EEPROM to the P1010RDB device tree.
The 24c01 acts as a memory SPD so it shouldn't be overwritten without
care.
The 24c256 is a general purpose memory.
Signed-off-by: Gustavo Zacarias <gustavo@zacarias.com.ar>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
This reverts commit 0c00f65653389a408dfbbee7578e671664eea26a.
The initial commit was my fault. There are two boards out there:
P2020RDB and P2020RDB-PC. I wasn't aware of that and assumed that I have
a RDB board in front of me while I the RDB-PC. This patch makes it work
for the RDB-PC variant and breaks it for the RDB. Now there is a device
tree file available for the RDB-PC which was not there earlier. So with
this revert, everything gets back to normal :)
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Add spi support for mgcoge into the platform code and the dts
file. Additionaly SPIDEV is switched on in the defconfig and the
updates for the newer kernel version are committed. The SPI
interface is used to drive the Maxim DS3106 clock chip.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
|
Switch on UBIFS, HOTPLUG and TIPC and update the config to
the latest kernel version.
Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Heiko Schocher <hs@denx.de>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
|
