| Age | Commit message (Collapse) | Author |
|---|
|
David Ahern says:
====================
net/ipv6: Address checks need to consider the L3 domain
IPv6 prohibits a local address from being used as a gateway for a route.
However, it is ok for the gateway to be a local address in a different L3
domain (e.g., VRF). This allows, for example, veth pairs to connect VRFs.
ip6_route_info_create calls ipv6_chk_addr_and_flags for gateway addresses
to determine if the address is a local one, but ipv6_chk_addr_and_flags
does not currently consider L3 domains. As a result routes can not be
added in one VRF with a nexthop that points to a local address in a
second VRF.
Resolve by comparing the l3mdev for the passed in device and requiring an
l3mdev match with the device containing an address. The intent of checking
for an address on the specified device versus any device in the domain is
mantained by a new argument to skip the check between the passed in device
and the device with the address.
Patch 1 moves the gateway validation from ip6_route_info_create into a
helper; the function is long enough and refactoring drops the indent
level.
Patch 2 adds a skip_dev_check argument to ipv6_chk_addr_and_flags to
allow a device to always be passed yet skip the device check when
looking at addresses and fixes up a few ipv6_chk_addr callers that
pass a NULL device.
Patch 3 adds l3mdev checks to ipv6_chk_addr_and_flags.
Patches 4 and 5 do some refactoring to the fib_tests script and then
patch 6 adds nexthop validation tests.
v4
- separated l3mdev check into a separate patch (patch 3 of this set)
as suggested by Kirill
- consolidated dev and ipv6_chk_addr_and_flags call into 1 if (Kirill)
- added a temp variable for gw type (Kirill)
v3
- set skip_dev_check in ipv6_chk_addr based on dev == NULL (per
comment from Ido)
v2
- handle 2 variations of route spec with sane error path
- add test cases
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add series of tests for valid and invalid nexthop specs for IPv6.
$ TEST=fib_nexthop_test ./fib_tests.sh
...
IPv6 nexthop tests
TEST: Directly connected nexthop, unicast address [ OK ]
TEST: Directly connected nexthop, unicast address with device [ OK ]
TEST: Gateway is linklocal address [ OK ]
TEST: Gateway is linklocal address, no device [ OK ]
TEST: Gateway can not be local unicast address [ OK ]
TEST: Gateway can not be local unicast address, with device [ OK ]
TEST: Gateway can not be a local linklocal address [ OK ]
TEST: Gateway can be local address in a VRF [ OK ]
TEST: Gateway can be local address in a VRF, with device [ OK ]
TEST: Gateway can be local linklocal address in a VRF [ OK ]
TEST: Redirect to VRF lookup [ OK ]
TEST: VRF route, gateway can be local address in default VRF [ OK ]
TEST: VRF route, gateway can not be a local address [ OK ]
TEST: VRF route, gateway can not be a local addr with device [ OK ]
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow a user to run just a specific fib test by setting the TEST
environment variable.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace 'ip -netns testns' with the alias IP. Shortens the line lengths
and makes running the commands manually a bit easier.
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lookup the L3 master device for the passed in device. Only consider
addresses on netdev's with the same master device. If the device is
not enslaved or is NULL, then the l3mdev is NULL which means only
devices not enslaved (ie, in the default domain) are considered.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ipv6_chk_addr_and_flags determines if an address is a local address and
optionally if it is an address on a specific device. For example, it is
called by ip6_route_info_create to determine if a given gateway address
is a local address. The address check currently does not consider L3
domains and as a result does not allow a route to be added in one VRF
if the nexthop points to an address in a second VRF. e.g.,
$ ip route add 2001:db8:1::/64 vrf r2 via 2001:db8:102::23
Error: Invalid gateway address.
where 2001:db8:102::23 is an address on an interface in vrf r1.
ipv6_chk_addr_and_flags needs to allow callers to always pass in a device
with a separate argument to not limit the address to the specific device.
The device is used used to determine the L3 domain of interest.
To that end add an argument to skip the device check and update callers
to always pass a device where possible and use the new argument to mean
any address in the domain.
Update a handful of users of ipv6_chk_addr with a NULL dev argument. This
patch handles the change to these callers without adding the domain check.
ip6_validate_gw needs to handle 2 cases - one where the device is given
as part of the nexthop spec and the other where the device is resolved.
There is at least 1 VRF case where deferring the check to only after
the route lookup has resolved the device fails with an unintuitive error
"RTNETLINK answers: No route to host" as opposed to the preferred
"Error: Gateway can not be a local address." The 'no route to host'
error is because of the fallback to a full lookup. The check is done
twice to avoid this error.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move gateway validation code from ip6_route_info_create into
ip6_validate_gw. Code move plus adjustments to handle the potential
reset of dev and idev and to make checkpatch happy.
Signed-off-by: David Ahern <dsahern@gmail.com>
Reviewed-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need for complex checking between the last consumed index
and current consumed index, a simple subtraction will do.
This also eliminates the possibility of a permanent transmit queue stall
under the following conditions:
- one CPU bursts ring->size worth of traffic (up to 256 buffers), to the
point where we run out of free descriptors, so we stop the transmit
queue at the end of bcm_sysport_xmit()
- because of our locking, we have the transmit process disable
interrupts which means we can be blocking the TX reclamation process
- when TX reclamation finally runs, we will be computing the difference
between ring->c_index (last consumed index by SW) and what the HW
reports through its register
- this register is masked with (ring->size - 1) = 0xff, which will lead
to stripping the upper bits of the index (register is 16-bits wide)
- we will be computing last_tx_cn as 0, which means there is no work to
be done, and we never wake-up the transmit queue, leaving it
permanently disabled
A practical example is e.g: ring->c_index aka last_c_index = 12, we
pushed 256 entries, HW consumer index = 268, we mask it with 0xff = 12,
so last_tx_cn == 0, nothing happens.
Fixes: 80105befdb4b ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Brad Mouring says:
====================
net: macb: Introduce phy-handle DT functionality
Consider the situation where a macb netdev is connected through
a phydev that sits on a mii bus other than the one provided to
this particular netdev. This situation is what this patchset aims
to accomplish through the existing phy-handle optional binding.
This optional binding (as described in the ethernet DT bindings doc)
directs the netdev to the phydev to use. This is precisely the
situation this patchset aims to solve, so it makes sense to introduce
the functionality to this driver (where the physical layout discussed
was encountered).
The devicetree snippet would look something like this:
...
ethernet@feedf00d {
...
phy-handle = <&phy0> // the first netdev is physically wired to phy0
...
phy0: phy@0 {
...
reg = <0x0> // MDIO address 0
...
}
phy1: phy@1 {
...
reg = <0x1> // MDIO address 1
...
}
...
}
ethernet@deadbeef {
...
phy-handle = <&phy1> // tells the driver to use phy1 on the
// first mac's mdio bus (it's wired thusly)
...
}
...
The work done to add the phy_node in the first place (dacdbb4dfc1a1:
"net: macb: add fixed-link node support") will consume the
device_node (if found).
v2: Reorganization of mii probe/init functions, suggested by Andrew Lunn
v3: Moved some of the bus init code back into init (erroneously moved to probe)
some style issues, and an unintialized variable warning addressed.
v4: Add Reviewed-by: tags
Skip fallback code if phy-handle phandle is found
v5: Cleanup formatting issues
Fix compile failure introduced in 1/4 "net: macb: Reorganize macb_mii
bringup"
Fix typo in "Documentation: macb: Document phy-handle binding"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Document the existence of the optional binding, directing to the
general ethernet document that describes this binding.
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This optional binding (as described in the ethernet DT bindings doc)
directs the netdev to the phydev to use. This is useful for a phy
chip that has >1 phy in it, and two netdevs are using the same phy
chip (i.e. the second mac's phy lives on the first mac's MDIO bus)
The devicetree snippet would look something like this:
ethernet@feedf00d {
...
phy-handle = <&phy0> // the first netdev is physically wired to phy0
...
phy0: phy@0 {
...
reg = <0x0> // MDIO address 0
...
}
phy1: phy@1 {
...
reg = <0x1> // MDIO address 1
...
}
...
}
ethernet@deadbeef {
...
phy-handle = <&phy1> // tells the driver to use phy1 on the
// first mac's mdio bus (it's wired thusly)
...
}
The work done to add the phy_node in the first place (dacdbb4dfc1a1:
"net: macb: add fixed-link node support") will consume the
device_node (if found).
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In phy_device's general probe, this device will already be set for
phy register polling, rendering this code redundant.
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The macb mii setup (mii_probe() and mii_init()) previously was
somewhat interspersed, likely a result of organic growth and hacking.
This change moves mii bus registration into mii_init and probing the
bus for devices into mii_probe.
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Need to lock lower socket in order to provide mutual exclusion
with kcm_unattach.
v2: Add Reported-by for syzbot
Fixes: ab7ac4eb9832e32a09f4e804 ("kcm: Kernel Connection Multiplexor module")
Reported-by: syzbot+ea75c0ffcd353d32515f064aaebefc5279e6161e@syzkaller.appspotmail.com
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The packet_mmap documentation had links to no longer existing web
sites; replace with other site which has similar example.
Support for packet mmap has been in mainline versions of libpcap
for several years.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When perf_group_dettach() is called on a group leader, it updates each
sibling's group_leader field to point to that sibling, effectively
upgrading each siblnig to a group leader. After perf_group_detach has
completed, the caller may free the leader event.
We only remove siblings from the group leader's sibling_list when the
leader has a non-empty group_node. This was fine prior to commit:
8343aae66167df67 ("perf/core: Remove perf_event::group_entry")
... as the sibling's sibling_list would be empty. However, now that we
use the sibling_list field as both the list head and the list entry,
this leaves each sibling with a non-empty sibling list, including the
stale leader event.
If perf_group_detach() is subsequently called on a sibling, it will
appear to be a group leader, and we'll walk the sibling_list,
potentially dereferencing these stale events. In 0day testing, this has
been observed to result in kernel panics.
Let's avoid this by always removing siblings from the sibling list when
we promote them to leaders.
Fixes: 8343aae66167df67 ("perf/core: Remove perf_event::group_entry")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: vincent.weaver@maine.edu
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: torvalds@linux-foundation.org
Cc: Alexey Budankov <alexey.budankov@linux.intel.com>
Cc: valery.cherepennikov@intel.com
Cc: linux-tip-commits@vger.kernel.org
Cc: eranian@google.com
Cc: acme@redhat.com
Cc: alexander.shishkin@linux.intel.com
Cc: davidcc@google.com
Cc: kan.liang@intel.com
Cc: Dmitry.Prohorov@intel.com
Cc: Jiri Olsa <jolsa@redhat.com>
Link: https://lkml.kernel.org/r/20180316131741.3svgr64yibc6vsid@lakrids.cambridge.arm.com
|
|
Mark noticed that the change to sibling_list changed some iteration
semantics; because previously we used group_list as list entry,
sibling events would always have an empty sibling_list.
But because we now use sibling_list for both list head and list entry,
siblings will report as having siblings.
Fix this with a custom for_each_sibling_event() iterator.
Fixes: 8343aae66167 ("perf/core: Remove perf_event::group_entry")
Reported-by: Mark Rutland <mark.rutland@arm.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: vincent.weaver@maine.edu
Cc: alexander.shishkin@linux.intel.com
Cc: torvalds@linux-foundation.org
Cc: alexey.budankov@linux.intel.com
Cc: valery.cherepennikov@intel.com
Cc: eranian@google.com
Cc: acme@redhat.com
Cc: linux-tip-commits@vger.kernel.org
Cc: davidcc@google.com
Cc: kan.liang@intel.com
Cc: Dmitry.Prohorov@intel.com
Cc: jolsa@redhat.com
Link: https://lkml.kernel.org/r/20180315170129.GX4043@hirez.programming.kicks-ass.net
|
|
Device drivers use get_device_system_crosststamp() to produce precise
system/device cross-timestamps. The PHC clock and ALSA interfaces, for
example, make the cross-timestamps available to user applications. On
Intel platforms, get_device_system_crosststamp() requires a TSC value
derived from ART (Always Running Timer) to compute the monotonic raw and
realtime system timestamps.
Starting with Intel Goldmont platforms, the PCIe root complex supports the
PTM time sync protocol. PTM requires all timestamps to be in units of
nanoseconds. The Intel root complex hardware propagates system time derived
from ART in units of nanoseconds performing the conversion as follows:
ART_NS = ART * 1e9 / <crystal frequency>
When user software requests a cross-timestamp, the system timestamps
(generally read from device registers) must be converted to TSC by the
driver software as follows:
TSC = ART_NS * TSC_KHZ / 1e6
This is valid when CPU feature flag X86_FEATURE_TSC_KNOWN_FREQ is set
indicating that tsc_khz is derived from CPUID[15H]. Drivers should check
whether this flag is set before conversion to TSC is attempted.
Suggested-by: Christopher S. Hall <christopher.s.hall@intel.com>
Signed-off-by: Rajvi Jingar <rajvi.jingar@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: peterz@infradead.org
Link: https://lkml.kernel.org/r/1520530116-4925-1-git-send-email-rajvi.jingar@intel.com
|
|
Toshiaki Makita says:
====================
Fix vlan untag and insertion for bridge and vlan with reorder_hdr off
As Brandon Carpenter reported[1], sending non-vlan-offloaded packets from
bridge devices ends up with corrupted packets. He narrowed down this problem
and found that the root cause is in skb_reorder_vlan_header().
While I was working on fixing this problem, I found that the function does
not work properly for double tagged packets with reorder_hdr off as well.
Patch 1 fixes these 2 problems in skb_reorder_vlan_header().
And it turned out that fixing skb_reorder_vlan_header() is not sufficient
to receive double tagged packets with reorder_hdr off while I was testing the
fix. Vlan tags got out of order when vlan devices with reorder_hdr disabled
were stacked. Patch 2 fixes this problem.
[1] https://www.spinics.net/lists/linux-ethernet-bridging/msg07039.html
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With reorder header off, received packets are untagged in skb_vlan_untag()
called from within __netif_receive_skb_core(), and later the tag will be
inserted back in vlan_do_receive().
This caused out of order vlan headers when we create a vlan device on top
of another vlan device, because vlan_do_receive() inserts a tag as the
outermost vlan tag. E.g. the outer tag is first removed in skb_vlan_untag()
and inserted back in vlan_do_receive(), then the inner tag is next removed
and inserted back as the outermost tag.
This patch fixes the behaviour by inserting the inner tag at the right
position.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When we have a bridge with vlan_filtering on and a vlan device on top of
it, packets would be corrupted in skb_vlan_untag() called from
br_dev_xmit().
The problem sits in skb_reorder_vlan_header() used in skb_vlan_untag(),
which makes use of skb->mac_len. In this function mac_len is meant for
handling rx path with vlan devices with reorder_header disabled, but in
tx path mac_len is typically 0 and cannot be used, which is the problem
in this case.
The current code even does not properly handle rx path (skb_vlan_untag()
called from __netif_receive_skb_core()) with reorder_header off actually.
In rx path single tag case, it works as follows:
- Before skb_reorder_vlan_header()
mac_header data
v v
+-------------------+-------------+------+----
| ETH | VLAN | ETH |
| ADDRS | TPID | TCI | TYPE |
+-------------------+-------------+------+----
<-------- mac_len --------->
<------------->
to be removed
- After skb_reorder_vlan_header()
mac_header data
v v
+-------------------+------+----
| ETH | ETH |
| ADDRS | TYPE |
+-------------------+------+----
<-------- mac_len --------->
This is ok, but in rx double tag case, it corrupts packets:
- Before skb_reorder_vlan_header()
mac_header data
v v
+-------------------+-------------+-------------+------+----
| ETH | VLAN | VLAN | ETH |
| ADDRS | TPID | TCI | TPID | TCI | TYPE |
+-------------------+-------------+-------------+------+----
<--------------- mac_len ---------------->
<------------->
should be removed
<--------------------------->
actually will be removed
- After skb_reorder_vlan_header()
mac_header data
v v
+-------------------+------+----
| ETH | ETH |
| ADDRS | TYPE |
+-------------------+------+----
<--------------- mac_len ---------------->
So, two of vlan tags are both removed while only inner one should be
removed and mac_header (and mac_len) is broken.
skb_vlan_untag() is meant for removing the vlan header at (skb->data - 2),
so use skb->data and skb->mac_header to calculate the right offset.
Reported-by: Brandon Carpenter <brandon.carpenter@cypherpath.com>
Fixes: a6e18ff11170 ("vlan: Fix untag operations of stacked vlans with REORDER_HEADER off")
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit d11790941dd3 ("enic: Add vxlan offload support for IPv6 pkts")
added vxlan offload support for IPv6 pkts. Required change in
enic_udp_tunnel_del was not made. This creates a bug where once user
adds IPv6 tunnel, hw offload for that cannot be deleted.
This patch removes check for IP proto in tunnel delete path. Driver need
not check for IP proto since same UDP port cannot be used to create two
tunnels.
Fixes: d11790941dd3 ("enic: Add vxlan offload support for IPv6 pkts")
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 3c181c12c431fe33b669410d663beb9cceefcd1b.
The offending patch was merged in 4.16-rc4 and was promptly applied to
stable kernels 4.14.25 and 4.15.8.
The patch causes a corruption in several superblock items on big-endian
machines because of messed up endianity conversions. The damage is
manually repairable. A filesystem cannot be mounted again after it has
been unmounted once.
We do a full revert and not a fixup so stable can pick that patch ASAP.
Fixes: 3c181c12c431 ("btrfs: use proper endianness accessors for super_copy")
Link: https://lkml.kernel.org/r/1521139304@msgid.manchmal.in-ulm.de
CC: stable@vger.kernel.org # 4.14+
Reported-by: Christoph Biedl <linux-kernel.bfrz@manchmal.in-ulm.de>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
The variable 'len' is being initialized with a value that is never
read and it is re-assigned later, hence the initialization is redundant
and can be removed.
Cleans up clang warning:
net/rxrpc/recvmsg.c:275:15: warning: Value stored to 'len' during its
initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid all the sizeof(drm_color_lut) business by using
drm_color_lut_size() to convert the blob length into
number of LUT entries.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180223192506.29992-6-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Now that blob->data is void* again we don't need to cast it.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180223192506.29992-5-ville.syrjala@linux.intel.com
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Provide a small helper to convert the blob length in bytes
to the number of LUT entries.
v2: Add kerneldoc (Daniel)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180315152338.7248-1-ville.syrjala@linux.intel.com
|
|
While we want to potentially support multiple different gamma/degamma
LUT sizes we can (and should) at least check that the blob length
is a multiple of the LUT entry size.
v2: s/expected_size_mod/expected_elem_size/ (Daniel)
Add kernel doc (Daniel)
v3: s/we/were/ typo in the docs
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20180315152241.7113-1-ville.syrjala@linux.intel.com
|
|
Now that blob->data is void* again we don't need the casts anymore.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180223192506.29992-2-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
Using a flexible array for the blob data was a mistake by me. It
forces all users of the blob data to cast blob->data to something
else. void* is clearly superior so let's go back to the original
scheme.
Not a clean revert as the code has moved.
This reverts commit d63f5e6bf6f2a1573ea39c9937cdf5ab0b3a4b77.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180223192506.29992-1-ville.syrjala@linux.intel.com
Reviewed-by: Shashank Sharma <shashank.sharma@intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
When using device passthrough with SME active, the MMIO range that is
mapped for the device should not be mapped encrypted. Add a check in
set_spte() to insure that a page is not mapped encrypted if that page
is a device MMIO page as indicated by kvm_is_mmio_pfn().
Cc: <stable@vger.kernel.org> # 4.14.x-
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Testing brcmfmac with more recent firmwares resulted in AP interfaces
not working in some specific setups. Debugging resulted in discovering
support for IAPP in Broadcom's firmwares.
Older firmwares were only generating 802.11f frames. Newer ones like:
1) 10.10 (TOB) (r663589)
2) 10.10.122.20 (r683106)
for 4366b1 and 4366c0 respectively seem to also /respect/ 802.11f frames
in the Tx path by performing a STA disassociation.
This obsoleted standard and its implementation is something that:
1) Most people don't need / want to use
2) Can allow local DoS attacks
3) Breaks AP interfaces in some specific bridge setups
To solve issues it can cause this commit modifies brcmfmac to drop IAPP
packets. If affects:
1) Rx path: driver won't be sending these unwanted packets up.
2) Tx path: driver will reject packets that would trigger STA
disassociation perfromed by a firmware (possible local DoS attack).
It appears there are some Broadcom's clients/users who care about this
feature despite the drawbacks. They can switch it on using a new module
param.
This change results in only two more comparisons (check for module param
and check for Ethernet packet length) for 99.9% of packets. Its overhead
should be very minimal.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
Third batch of iwlwifi fixes intended for 4.16:
* Fix an issue with the multicast queue;
* Fix IGTK handling;
* Fix some missing return value checks;
* Add support for a HW workaround for issues on some platforms;
|
|
Arnd Bergman reports:
"""
The conditional spinlock confuses gcc into thinking the 'flags' value
might contain uninitialized data:
drivers/gpu/drm/i915/i915_pmu.c: In function '__i915_pmu_event_read':
arch/x86/include/asm/paravirt_types.h:573:3: error: 'flags' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The code is correct, but it's easy to see how the compiler gets confused
here. This avoids the problem by pulling the lock outside of the function
into its only caller.
"""
On deeper look it seems this is caused by paravirt spinlocks
implementation when CONFIG_PARAVIRT_DEBUG is set, which by being
complicated, manages to convince gcc locked parameter can be changed
externally (impossible).
Work around it by removing the conditional locking parameters altogether.
(It was never the most elegant code anyway.)
Slight penalty we now pay is an additional irqsave spin lock/unlock cycle
on the event enable path. But since enable is not a fast path, that is
preferrable to the alternative solution which was doing MMIO under irqsave
spinlock.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 1fe699e30113 ("drm/i915/pmu: Fix sleep under atomic in RC6 readout")
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: David Airlie <airlied@linux.ie>
Cc: intel-gfx@lists.freedesktop.org
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20180314080535.17490-1-tvrtko.ursulin@linux.intel.com
(cherry picked from commit ad055fb8e010e4ff37f66aeed1d380329bddce67)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
tasklet_kill() will spin waiting for the current tasklet to be executed.
However, if tasklet_disable() has been called, then the tasklet is never
executed but permanently put back onto the runlist until
tasklet_enable() is called. Ergo, we cannot use tasklet_kill() inside a
disable/enable pair. This is the case when we call set-wedge from inside
i915_reset(), and another request was submitted to us concurrent to the
reset.
Fixes: 963ddd63c314 ("drm/i915: Suspend submission tasklets around wedging")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307134226.25492-6-chris@chris-wilson.co.uk
(cherry picked from commit 68ad361285a9cc73b259f59adbaafde196c15987)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
Similar to the staging around handling of engine->submit_request, we
need to stop adding to the execlists->queue prior to calling
engine->cancel_requests. cancel_requests will move requests from the
queue onto the timeline, so if we add a request onto the queue after that
point, it will be lost.
Fixes: af7a8ffad9c5 ("drm/i915: Use rcu instead of stop_machine in set_wedged")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180307134226.25492-5-chris@chris-wilson.co.uk
(cherry picked from commit 47650db02dd52267953df81438c93cf8a0eb0e5e)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
We don't want to preserve the DDI A 4 lane bit on ICL.
Fixes: 3d2011cfa41f ("drm/i915/icl: remove port A/E lane sharing limitation.")
Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180306104155.3526-1-jani.nikula@intel.com
(cherry picked from commit 1e6aa7e55c28ecd842b8b4599e4273c2429ee061)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
|
|
Microblaze doesn't set CONFIG_NO_BOOTMEM and so memblock_virt_alloc()
doesn't work for CONFIG_HAVE_MEMBLOCK && !CONFIG_NO_BOOTMEM.
Similar change was already done by others architectures
"ARM: mm: Remove bootmem code and switch to NO_BOOTMEM"
(sha1: 84f452b1e8fc73ac0e31254c66e3e2260ce5263d)
or
"openrisc: Consolidate setup to use memblock instead of bootmem"
(sha1: 266c7fad157265bb54d17db1c9545f2aaa488643)
or
"parisc: Drop bootmem and switch to memblock"
(sha1: 4fe9e1d957e45ad8eba9885ee860a0e93d13a7c7)
or
"powerpc: Remove bootmem allocator"
(sha1: 10239733ee8617bac3f1c1769af43a88ed979324)
or
"s390/mm: Convert bootmem to memblock"
(sha1: 50be634507284eea38df78154d22615d21200b42)
or
"sparc64: Convert over to NO_BOOTMEM."
(sha1: 625d693e9784f988371e69c2b41a2172c0be6c11)
or
"xtensa: drop sysmem and switch to memblock"
(sha1: 0e46c1115f5816949220d62dd3ff04aa68e7ac6b)
Issue was introduced by:
"of/fdt: use memblock_virt_alloc for early alloc"
(sha1: 0fa1c579349fdd90173381712ad78aa99c09d38b)
Signed-off-by: Rob Herring <robh@kernel.org>
Tested-by: Alvaro Gamez Machado <alvaro.gamez@hazent.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
alloc_maybe_bootmem is unused, so remove it.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
The patch:
"microblaze: Setup proper dependency for optimized lib functions"
(sha1: 7b6ce52be3f86520524711a6f33f3866f9339694)
didn't setup all dependencies properly.
Optimized lib functions in C are also present for little endian
and optimized library functions in assembler are implemented only for
big endian version.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
|
|
In accordance with Intel's microcode revision guidance from March 6 MCU
rev 0xc2 is cleared on both Skylake H/S and Skylake Xeon E3 processors
that share CPUID 506E3.
Signed-off-by: Alexander Sergeyev <sergeev917@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Jia Zhang <qianyue.zj@alibaba-inc.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Kyle Huey <me@kylehuey.com>
Cc: David Woodhouse <dwmw@amazon.co.uk>
Link: https://lkml.kernel.org/r/20180313193856.GA8580@localhost.localdomain
|
|
There are 2 Type-c PHYs in RK3399, but only one DP controller. Hence
only one PHY can connect to DP controller at one time, the other should
be disconnected. The GRF_SOC_CON26 register has a switch bit to do it,
set this bit means enable PHY 1, clear this bit means enable PHY 0.
If the board has 2 Type-C ports, the DP driver get the phy id from
devm_of_phy_get_by_index, and then control this switch according to
this id. But some others board only has one Type-C port, it may be PHY 0
or PHY 1. The dts node id can not tell us the correct PHY id. Hence move
this switch to PHY driver, the PHY driver can distinguish between PHY 0
and PHY 1, and then write the correct register bit.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
[The phy-changes are in the phy-tree now and the cdn-dp wasn't
enabled at all so far, so this change can go through drm-misc
alone without causing issues when testing drm-misc]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20180216120956.19034-6-enric.balletbo@collabora.com
|
|
Some devices use a shared clock which is very sensitive to variations
and cause trouble in some situations. We need to set a bit in the phy
configuration to indicate that to the FW. To make this generic, add a
extra_phy_config_flags element to the device configuration and OR it
into the phy_cfg before sending it to the firmware. And also create a
set of configurations for devices that use shared clocks and need this
extra bit to be set.
Fixes: c62446d2b028 ("iwlwifi: add new 9460 series PCI IDs")
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The earlier patch called the station add functions but didn't
assign their return value to the ret variable, so that the
checks for it were meaningless. Fix that.
Found by smatch:
.../mac80211.c:2560 iwl_mvm_start_ap_ibss() warn: we tested 'ret' before and it was 'false'
.../mac80211.c:2563 iwl_mvm_start_ap_ibss() warn: we tested 'ret' before and it was 'false'
Fixes: 3a89411cd31c ("iwlwifi: mvm: fix assert 0x2B00 on older FWs")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Currently when an IGTK is set for an AP, it is set as a regular key.
Since the cipher is set to CMAC, the STA_KEY_FLG_EXT flag is added to
the host command, which causes assert 0x253D on NICs that do not support
this.
Fixes: 85aeb58cec1a ("iwlwifi: mvm: Enable security on new TX API")
Signed-off-by: Beni Lev <beni.lev@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The tid being used for the queue (cab_queue) for the MCAST
station has been changed recently to be 0 (for BE).
The flush path still flushed only the special tid (15)
which means that the firmware wasn't flushing the right
queue and we could get a firmware crash upon remove
station if we had an MCAST packet on the ring.
The current code that flushes queues for a station only
differentiates between internal stations (stations that
aren't instantiated in mac80211, like the MCAST station)
and the non-internal ones.
Internal stations can be either: BCAST (beacons), MCAST
(for cab_queue), GENERAL_PURPOSE (p2p dev, and sniffer
injection). The internal stations can use different tids.
To make the code simpler, just flush all the tids always
and add the special internal tid (15) for internal
stations. The firmware will know how to handle this even
if we hadn't any queue mapped that that tid.
Fixes: e340c1a6ef4b ("iwlwifi: mvm: Correctly set the tid for mcast queue")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Tile was the only remaining architecture to implement alloc_remap(),
and since that is being removed, there is no point in keeping this
function.
Removing all callers simplifies the mem_map handling.
Reviewed-by: Pavel Tatashin <pasha.tatashin@oracle.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The CONFIG_MPU option was only defined on blackfin, and that architecture
is now being removed, so the respective code can be simplified.
A lot of other microcontrollers have an MPU, but I suspect that if we
want to bring that support back, we'd do it differently anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Hardwall is a tile specific feature, and with the removal of the
tile architecture, this has become dead code, so let's remove it.
Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
The port was added back in 2000 so it's no longer even a good source
of inspiration for newer ports (if it ever was)
The last SoC (ARTPEC-3) with a CRIS main CPU was launched in 2008.
Coupled with time and working developer board hardware being
in low supply, it's time to drop the port from Linux.
So long and thanks for all the fish!
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
