| Age | Commit message (Collapse) | Author |
|---|
|
used by sg list
When using the commands below to write some data to a virtio-scsi LUN of the
QEMU guest(32-bit) with 1G physical memory(qemu -m 1024), the qemu will crash.
# sudo mkfs.ext4 /dev/sdb (/dev/sdb is the virtio-scsi LUN.)
# sudo mount /dev/sdb /mnt
# dd if=/dev/zero of=/mnt/file bs=1M count=1024
In current implementation, sg_set_buf is called to add buffers to sg list which
is put into the virtqueue eventually. But if there are some HighMem pages in
table->sgl you can not get virtual address by sg_virt. So, sg_virt(sg_elem) may
return NULL value. This will cause QEMU exit when virtqueue_map_sg is called
in QEMU because an invalid GPA is passed by virtqueue.
Two solutions are discussed here:
http://lkml.indiana.edu/hypermail/linux/kernel/1207.3/00675.html
Finally, value assignment approach was adopted because:
Value assignment creates a well-formed scatterlist, because the termination
marker in source sg_list has been set in blk_rq_map_sg(). The last entry of the
source sg_list is just copied to the the last entry in destination list. Note
that, for now, virtio_ring does not care about the form of the scatterlist and
simply processes the first out_num + in_num consecutive elements of the sg[]
array.
I have tested the patch on my workstation. QEMU would not crash any more.
Cc: <stable@vger.kernel.org> # 3.4: 4fe74b1: [SCSI] virtio-scsi: SCSI driver
Signed-off-by: Wang Sen <senwang@linux.vnet.ibm.com>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
|
|
The code currently always selects turbo mode for PCA9665, no matter which
clock frequency is configured. This is because it compares the clock frequency
against constants reflecting (boundary / 100). Compare against real boundary
frequencies to fix the problem.
Signed-off-by: Thomas Kavanagh <tkavanagh@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
|
|
Guide people to where their patches can be found these days.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
|
|
Peer link which is blocked using the "iw mesh0 station
set <MAC addr> plink_action block" is previously not able
to re-open using "iw mesh0 station set <MAC addr>
plink_action open". This patch is intended to solve this.
If the station plink state remains at OPN_SNT once open,
try block and open again should solve this problem.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Make the function acquire the necessary mutex itself
to simplify the callers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Currently, mac80211 uses the power constraint IE, and reduces
the regulatory max TX power by it. This can cause issues if
the AP is advertising a large power constraint value matching
a high TX power in its country IE, for example in this case:
...
Country: US Environment: Indoor/Outdoor
...
Channels [157 - 157] @ 30 dBm
...
Power constraint: 13 dB
...
What happened here is that our local regulatory TX power is
15 dBm, and gets reduced by 13 dB so we end up with only
2 dBm effective TX power, which is way too low.
Instead, handle the country IE/power constraint IE combined
and restrict our TX power to the max of the regulatory power
and the maximum power advertised by the AP, in this case
17 dBm (= 30 dBm - 13 dB).
Also print a message when this happens to let the user know
and help us debug issues with it.
Reported-by: Carl A. Cook <CACook@quantum-equities.com>
Tested-by: Carl A. Cook <CACook@quantum-equities.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
We noticed a plymouth bug on Fedora 18, and I then
noticed this stupid thinko, fixing it fixed the problem
with plymouth.
Cc: stable@vger.kernel.org
Acked-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
|
|
Avoid the construction of a malformed DMA request sent to
the DMA controller.
Log message is for debug only because this condition is unlikely to
append and may only trigger at driver development time.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Stable <stable@vger.kernel.org> [2.6.31+]
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
s/dma_memcpy/slave_sg/ and it is sg length that we are
talking about.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Stable <stable@vger.kernel.org> [2.6.31+]
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
|
|
into drm-fixes
Alex writes:
This is the current set of radeon fixes for 3.6. Two small fixes:
- fix the fence issues introduced in 3.5 with 64-bit fences
- PLL fix for multiple DP heads
* 'drm-fixes-3.6' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: make 64bit fences more robust v3
drm/radeon: rework pll selection (v3)
|
|
This patch adds on the fixes done in commits 89dd86db78e0 ("mlx4_core:
Allow large mlx4_buddy bitmaps") and 3de819e6b642 ("mlx4_core: Fix
integer overflow issues around MTT table") so that memory registration
of up to 8TB (log_num_mtt=31) finally works.
It fixes integer overflows in a few mlx4_table_yyy routines in icm.c
by using a u64 intermediate variable, and int/uint issues that caused
table indexes to become nagive by setting some variables to be u32
instead of int. These problems cause crashes when a user attempted to
register > 512GB of RAM.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
Commit 0090def("ACPI: Add interface to register/unregister device
to/from power resources") used resource_lock to protect the devices list
that relies on power resource. It caused a mutex dead lock, as below
acpi_power_on ---> lock resource_lock
__acpi_power_on
acpi_power_on_device
acpi_power_get_inferred_state
acpi_power_get_list_state ---> lock resource_lock
This patch adds a new mutex "devices_lock" to protect the devices list
and calls acpi_power_on_device in acpi_power_on, instead of
__acpi_power_on, after the resource_lock is released.
[rjw: Changed data type of a boolean variable to bool.]
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
It turns out that there are ACPI BIOSes defining device objects with
_PSx and without either _PSC or _PRx. For devices corresponding to
those ACPI objetcs __acpi_bus_get_power() returns ACPI_STATE_UNKNOWN
and their initial power states are regarded as unknown as a result.
If such a device is a parent of another power-manageable device, the
child cannot be put into a low-power state through ACPI, because
__acpi_bus_set_power() refuses to change power states of devices
whose parents' power states are unknown.
To work around this problem, observe that the ACPI power state of
a device cannot be higher-power (lower-number) than the power state
of its parent. Thus, if the device's _PSC method or the
configuration of its power resources indicates that the device is
in D0, the device's parent has to be in D0 as well. Consequently,
if the parent's power state is unknown when we've just learned that
its child's power state is D0, we can safely set the parent's
power.state field to ACPI_STATE_D0.
Tested-by: Aaron Lu <aaron.lu@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
|
|
If vlan option is being specified in the pktgen and packet size
being requested is less than 46 bytes, despite being illogical
request, pktgen should not crash the kernel.
BUG: unable to handle kernel paging request at ffff88021fb82000
Process kpktgend_0 (pid: 1184, threadinfo ffff880215f1a000, task ffff880218544530)
Call Trace:
[<ffffffffa0637cd2>] ? pktgen_finalize_skb+0x222/0x300 [pktgen]
[<ffffffff814f0084>] ? build_skb+0x34/0x1c0
[<ffffffffa0639b11>] pktgen_thread_worker+0x5d1/0x1790 [pktgen]
[<ffffffffa03ffb10>] ? igb_xmit_frame_ring+0xa30/0xa30 [igb]
[<ffffffff8107ba20>] ? wake_up_bit+0x40/0x40
[<ffffffff8107ba20>] ? wake_up_bit+0x40/0x40
[<ffffffffa0639540>] ? spin+0x240/0x240 [pktgen]
[<ffffffff8107b4e3>] kthread+0x93/0xa0
[<ffffffff81615de4>] kernel_thread_helper+0x4/0x10
[<ffffffff8107b450>] ? flush_kthread_worker+0x80/0x80
[<ffffffff81615de0>] ? gs_change+0x13/0x13
The root cause of why pktgen is not able to handle this case is due
to comparison of signed (datalen) and unsigned data (sizeof), which
eventually passes a huge number to skb_put().
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove useless kfree() and clean up code related to the removal.
The semantic patch that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r exists@
position p1,p2;
expression x;
@@
if (x@p1 == NULL) { ... kfree@p2(x); ... return ...; }
@unchanged exists@
position r.p1,r.p2;
expression e <= r.x,x,e1;
iterator I;
statement S;
@@
if (x@p1 == NULL) { ... when != I(x,...) S
when != e = e1
when != e += e1
when != e -= e1
when != ++e
when != --e
when != e++
when != e--
when != &e
kfree@p2(x); ... return ...; }
@ok depends on unchanged exists@
position any r.p1;
position r.p2;
expression x;
@@
... when != true x@p1 == NULL
kfree@p2(x);
@depends on !ok && unchanged@
position r.p2;
expression x;
@@
*kfree@p2(x);
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
geting route info does not write rt->rt6i_table, so replace
write lock with read lock
Suggested-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Li RongQing <roy.qing.li@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We kmemdup() templates, so they can be const.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The acpi_evalf() function modifies four bytes of data but in
fan_get_status() we pass a pointer to u8. I have modified the
function to use type checking now.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
Fix a device reference count leakage issue in function
eeepc_rfkill_hotplug().
Signed-off-by: Jiang Liu <jiang.liu@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
MODULE_PARM_DESC for wlan_status is further in the same file
Signed-off-by: Maxim A. Nikulin <M.A.Nikulin@gmail.com>
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
Resolves-bug: https://bugzilla.kernel.org/show_bug.cgi?id=24222
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
Signed-off-by: Corentin Chary <corentin.chary@gmail.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
This function fails to add the start address of the gmux I/O range to
the requested port address and thus writes to the wrong location.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
Study of Apple's binary driver revealed that the GMUX_READ_PORT should
be written between calls to gmux_index_wait_ready and
gmux_index_wait_complete (i.e., the new index protocol must be
followed). If this is not done correctly, the indexed
gmux device only partially accepts writes which lead to problems
concerning GPU switching. Special thanks to Seth Forshee who helped
greatly with identifying unnecessary changes.
Signed-off-by: Bernhard Froemel <froemel@vmars.tuwien.ac.at>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
This patch extracts and displays version information from the indexed
gmux device as it is also done for the classic gmux device.
Signed-off-by: Bernhard Froemel <froemel@vmars.tuwien.ac.at>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
|
|
Commit a334872224a67b614dc888460377862621f3dac7 added afex support but lacked
several logical changes. This lack can cause afex to crash, and also
have a slight effect on other flows (i.e., driver always assumes the Tx ring
has less available buffers than what it actually has).
This patch adds the missing segments, fixing said issues.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Barak Witkowski <barak@broadcom.com>
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under traffic, there are several registers that when read (e.g., via
'ethtool -d') may cause the chip to stall.
This patch corrects the registers read in such flows.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch propagates users' requested flow-control into the link layer,
which will later be used to advertise this flow-control for auto-negotiation
(until now these values were ignored).
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prior to this fix, the driver reported the chip's active duplex state
is always 'full', even if using half-duplex mode.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Prevent updating the xmac PFC configuration when using a link speed
slower than 10G -the umac block is responsible for 1G or slower connections,
therefore it is possible the xmac block is reset when connection is slower.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
FW needs the driver statistics for management. Current logic is broken
in that the function that gathers the port statistics does not copy
its own statistics to a place where the FW can use it.
This patch causes every function that can pass statistics to the FW to
do so.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During traffic when DCB is enabled, it is possible for multiple instances
of statistics queries to be sent to the chip - this may cause the FW to assert.
This patch prevents the sending of an additional instance of statistics query
while the previous query hasn't completed.
Signed-off-by: Dmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Compare bits up to the source address's prefix length only to
allows DNS load balancing to continue to be used as a tie breaker.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added labels for site-local addresses (fec0::/10) and 6bone testing
addresses (3ffe::/16) in order to depreference them.
Note that the RFC introduced new rows for Teredo, ULA and 6to4 addresses
in the default policy table. Some of them have different labels from ours.
For backward compatibility, we do not change the "default" labels.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The scsi netlink code confuses the netlink port id with a process id,
going so far as to read NETLINK_CREDS(skb)->pid instead of the correct
NETLINK_CB(skb).pid. Fortunately it does not matter because nothing
registers to respond to scsi netlink requests.
The only interesting use of the scsi_netlink interface is
fc_host_post_vendor_event which sends a netlink multicast message.
Since nothing registers to handle scsi netlink messages kill all of the
registration logic, while retaining the same error handling behavior
preserving the userspace visible behavior and removing all of the
confused code that thought a netlink port id was a process id.
This was tested with a kernel allyesconfig build which had no problems.
Cc: James Bottomley <James.Bottomley@parallels.com>
Cc: James Smart <James.Smart@Emulex.Com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace the current (inefficient) for-loop with memcpy, to copy priomap.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The update_netdev_tables() function appears to be unnecessary, since the
write_update_netdev_table() function will adjust the priomaps as and when
required anyway. So drop the usage of update_netdev_tables() entirely.
Signed-off-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only increase the higher 32bits if we really detect a wrap around.
v2: instead of increasing the higher 32bits just use the higher
32bits from the last emitted fence.
v3: also use last emitted fence value as upper limit.
The intention of this patch is to make fences as robust as
they where before introducing 64bit fences. This is
necessary because on older systems it looks like the fence
value gets corrupted on initialization.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=51344
Should also fix:
https://bugs.freedesktop.org/show_bug.cgi?id=54129
https://bugs.freedesktop.org/show_bug.cgi?id=54662
https://bugzilla.redhat.com/show_bug.cgi?id=846505
https://bugzilla.redhat.com/show_bug.cgi?id=845639
3.5 needs a separate patch due to changes in the
fence code. Will send that out separately.
Signed-off-by: Christian König <deathsimple@vodafone.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
For DP we can use the same PPLL for all active DP
encoders. Take advantage of that to prevent cases
where we may end up sharing a PPLL between DP and
non-DP which won't work. Also clean up the code
a bit.
v2: - fix missing pll_id assignment in crtc init
v3: - fix DP PPLL check
- document functions
- break in main encoder search loop after matching.
no need to keep checking additional encoders.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=54471
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This fixes a hang on suspend due to calling wdm_suspend on
the unregistered data interface. The hang should have been
a NULL pointer reference had it not been for a logic error
in the cdc_wdm code.
commit 230718bd net: qmi_wwan: bind to both control and data interface
changed qmi_wwan to use cdc_wdm as a subdriver for devices with
a two-interface QMI/wwan function. The commit failed to update
qmi_wwan_suspend and qmi_wwan_resume, which were written to handle
either a single combined interface function, or no subdriver at all.
The result was that we called into the subdriver both when the
control interface was suspended and when the data interface was
suspended. Calling the subdriver suspend function with an
unregistered interface is not supported and will make the
subdriver bug out.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
gred_dequeue() and gred_drop() do not seem to get called when the
queue is empty, meaning that we never start idling while in WRED
mode. And since qidlestart is not stored by gred_store_wred_set(),
we would never stop idling while in WRED mode if we ever started.
This messes up the average queue size calculation that influences
packet marking/dropping behavior.
Now, we start WRED mode idling as we are removing the last packet
from the queue. Also we now actually stop WRED mode idling when we
are enqueuing a packet.
Cc: Bruce Osler <brosler@cisco.com>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
q->vars.qavg is a Wlog scaled value, but q->backlog is not. In order
to pass q->vars.qavg as the backlog value, we need to un-scale it.
Additionally, the qave value returned via netlink should not be Wlog
scaled, so we need to un-scale the result of red_calc_qavg().
This caused artificially high values for "Average Queue" to be shown
by 'tc -s -d qdisc', but did not affect the actual operation of GRED.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each pair of DPs only needs to be compared once when searching for
a non-unique prio value.
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change various flows in the bnx2x driver which up until now flapped
the link - these flows now benefit from the link flap avoidance mechanism.
This includes the removal of the link reset made upon nic init, as it is
possible the link is already active at that time.
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Various flows in the bnx2x driver cause a link-flap - if the link
is up, it would be toggled down (after a mac/phy reset) and then
taken back up.
In many of these cases, there is no need to do cause such a flap,
as the associated flows should not actually affect the link.
This patch adds the 'Link Flap Avoidance' mechanism, which allows
the driver to better determine if a given flow requires a link change,
and thus minimize the number of link flaps caused by the driver.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Separate the interrupt setting part of each external PHY to a specific
function.
This allows calling the interrupt setting in case of link-flap avoidance,
since some link owners may not enable the interrupt on their own.
Signed-off-by: Yaniv Rosner <yaniv.rosner@broadcom.com>
Signed-off-by: Yuval Mintz <yuvalmin@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is a bad idea to hold a spinlock and call flush_work_sync.
Move the workqueue cleanup outside the spinlock and use cancel_work_sync,
on closing the channel this seems to be the more correct function.
Remove the never used and constant return value of mISDN_freebchannel.
Signed-off-by: Karsten Keil <keil@b1-systems.de>
Cc: <stable@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso says:
====================
The following patchset contains four Netfilter updates, mostly targeting
to fix issues added with IPv6 NAT, and one little IPVS update for net-next:
* Remove unneeded conditional free of skb in nfnetlink_queue, from
Wei Yongjun.
* One semantic path from coccinelle detected the use of list_del +
INIT_LIST_HEAD, instead of list_del_init, again from Wei Yongjun.
* Fix out-of-bound memory access in the NAT address selection, from
Florian Westphal. This was introduced with the IPv6 NAT patches.
* Two fixes for crashes that were introduced in the recently merged
IPv6 NAT support, from myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pablo Neira Ayuso say:
====================
The following patchset contains four updates for your net tree, they are:
* Fix crash on timewait sockets, since the TCP early demux was added,
in nfnetlink_log, from Eric Dumazet.
* Fix broken syslog log-level for xt_LOG and ebt_log since printk format was
converted from <.> to a 2 bytes pattern using ASCII SOH, from Joe Perches.
* Two security fixes for the TCP connection tracking targeting off-path attacks,
from Jozsef Kadlecsik. The problem was discovered by Jan Wrobel and it is
documented in: http://mixedbit.org/reflection_scan/reflection_scan.pdf.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
