summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2012-07-10HID: add support for 2012 MacBook Pro RetinaRyan Bourgeois
Add support for the 15'' MacBook Pro Retina. The keyboard is the same as recent models. The patch needs to be synchronized with the bcm5974 patch for the trackpad - as usual. Patch originally written by clipcarl (forums.opensuse.org). [rydberg@euromail.se: Amended mouse ignore lines] Signed-off-by: Ryan Bourgeois <bluedragonx@gmail.com> Signed-off-by: Henrik Rydberg <rydberg@euromail.se> Acked-by: Jiri Kosina <jkosina@suse.cz> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2012-07-10ASoC: arizona: Support variable FLL VCO multipliersMark Brown
Some Arizona chips have a higher frequency for the FLL VCO, support this in the common code. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-10ath9k_hw: remove debugging masks from AR_MCI_INTERRUPT_RX_MSG_DEFAULTRajkumar Manoharan
Remove the CONT_* and LNA_* messages from AR_MCI_INTERRUPT_RX_MSG_DEFAULT. Those MCI rx messages only meant for debugging purpose. Including them in default rx_msg series could raise huge amount of MCI interrupts when BT traffic is going on. And also it increases power consumption when WLAN is scanning. Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10brcmsmac: handle non PCI devices in the phy codeHauke Mehrtens
Some code in write_{radio,radio}_reg() should just be run if this is a pci based device. Add the condition again which was removed in commit: commit 821e4e93172e4f7d5ac1eade04665c3dc5049c4a Author: Roland Vossen <rvossen@broadcom.com> Date: Mon Aug 8 15:58:58 2011 +0200 staging: brcm80211: removed unused bus code from softmac Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10brcmsmac: fix read in write_phy_regHauke Mehrtens
This reverts a unintended change mad in commit. commit 4b006b11ca18995677c5f1cd03cc9c42fbe80693 Author: Arend van Spriel <arend@broadcom.com> Date: Thu Dec 8 15:06:54 2011 -0800 brcm80211: smac: use bcma functions for register access in phy code Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10brcmsmac: extend brcms_c_chipmatch() to also handle non PCIe devicesHauke Mehrtens
Now brcms_c_chipmatch() is also able to handle non PCI devices and also does some checking for SoC if they are supported by brcmsmac. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10brcmsmac: fix DMA on SoCsHauke Mehrtens
These extra offsets are only needed by PCIe devices and not when running on an SoC. This partly reverts commit: commit 821e4e93172e4f7d5ac1eade04665c3dc5049c4a Author: Roland Vossen <rvossen@broadcom.com> Date: Mon Aug 8 15:58:58 2011 +0200 staging: brcm80211: removed unused bus code from softmac Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10brcmsmac: extend xmtfifo_sz arrayHauke Mehrtens
The xmtfifo_sz array contains the queue sizes for the different core revs. This array missed the sizes for the core rev 17 and 28. This patch extends the array to also include these sizes and adds a warning if no queue size is stored in the array for the given core rev. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10brcmsmac: add some workarounds for other chips againHauke Mehrtens
This adds some workarounds for the BCM4716, BCM47162, BCM5357 to the phy code again. This patch reverts parts of the following patch. commit c2c724977f95135f397fe0cb45f3c041d26b91e1 Author: Arend van Spriel <arend@broadcom.com> Date: Wed Jun 29 16:46:35 2011 -0700 staging: brcm80211: remove unsupported chipset code from brcmsmac phy The BCM4716 is working for me with an other firmware and I am working on adding support for the other chips. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10brcmsmac: add a conditions for core rev 17 againHauke Mehrtens
This reverts some changes made in this commit: commit 7234592364e2efe8b4ac1040c99b1d7ef01cf502 Author: Roland Vossen <rvossen@broadcom.com> Date: Mon Feb 14 12:16:45 2011 +0100 staging: brcm80211: removal of inactive d11 code The bcm4716 has a rev 17 wireless core and this condition is needed. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10brcmsmac: remove some unnessessacry casts and void pointerHauke Mehrtens
Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10brcmsmac: use chip and package id constants from bcmaHauke Mehrtens
This patch depends on addin the chip IDs to bcma done in this commit in my pending patch series for bcma. Author: Hauke Mehrtens <hauke@hauke-m.de> Date: Sun Jun 3 18:17:57 2012 +0200 bcma: add constants for chip ids Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10brcmsmac: use core id constants from bcmaHauke Mehrtens
This patch depends on adding the IDs to bcma done in this commit in my pending patch series for bcma. Author: Hauke Mehrtens <hauke@hauke-m.de> Date: Sun Jun 3 18:17:57 2012 +0200 bcma: add constants for chip ids Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10brcmsmac: remove some redundant chip common workaroundsHauke Mehrtens
The removed workarounds are already performed in bcma_pmu_workarounds() and bcma_core_chipcommon_init() This patch depends on the completion of the workarounds in bcma done in this commit in my pending patch series for bcma. Author: Hauke Mehrtens <hauke@hauke-m.de> Date: Mon Jun 4 00:20:26 2012 +0200 bcma: complete workaround for BCMA43224 and BCM4313 Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10brcmsmac: remove si_pmu_spuravoid_pllupdate()Hauke Mehrtens
si_pmu_spuravoid_pllupdate() is now replaced by bcma_pmu_spuravoid_pllupdate() which does the same thing, but supports more chips. This function is in my pending patch series for bcma. Author: Hauke Mehrtens <hauke@hauke-m.de> Date: Mon Jun 4 01:31:32 2012 +0200 bcma: add bcma_pmu_spuravoid_pllupdate() Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10brcmsmac: remove si_pmu_init() and si_pmu_res_init()Hauke Mehrtens
This is already done by bcma_pmu_init() and bcma_pmu_resources_init() in bcma. Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10brcmsmac: remove ai_findcore()Hauke Mehrtens
bcma also stores a pointer to the chipcommon core in its struct, brcmsmac should use it and not search for the core by its own. Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10brcmsmac: use container_of instead of castHauke Mehrtens
Now "struct si_pub pub" does not have to be the first member in struct si_info any more, if it is the resulting code after compilation should be the same. Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10brcmsmac: remove ai_get_buscore{type,rev}()Hauke Mehrtens
These two functions are not used any more. Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10brcmsmac: remove PCI_FORCEHT() macroHauke Mehrtens
The BCM4716 is a SoC and does not have a PCI client interface, so this condition is never true. Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10brcmsmac: remove PCIE() macroHauke Mehrtens
Instead of checking if there is a PCIe core on the bus, better check if hosttype is PCIe. In the original submission to staging PCIE() checked, if the bustype is PCI and the buscore is a PCIe core. Now we assume that all cores bcma supports are PCIe based, so we just have to check if the bustype is PCI. The old code bcmsmac currently uses searches for a PCIe core on the bus and if there is one assumes that this is the buscore, which is wrong. Some SoCs have a PCIe core operating in host mode and this is not the bus core. The old code also caused a null pointer in ai_get_buscoretype() and ai_get_buscorerev() if buscore was not set because there was no PCIe core on the bus. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Arend van Spriel <arend@broadcom.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10iwmc3200wifi: remove driver for unavailable hardwareJohn W. Linville
This hardware never became available to normal humans. Leaving this driver imposes unwelcome maintenance costs for no clear benefit. Signed-off-by: John W. Linville <linville@tuxdriver.com> Acked-by: Samuel Ortiz <sameo@linux.intel.com>
2012-07-10regulator: tps65910: correct init value of n_voltagesLaxman Dewangan
Recent change in the core driver to get the maximum voltage is based on the (n_voltages -1) steps of voltage. For the tps65910, the (n_voltages -1)th step voltage is calculated based on the callback function list_voltage. This function direct maps the datasheet and adjust the first few steps for initial voltage as per datasheet, and hence initialize the n_voltages based on datasheet. Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com> Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
2012-07-10wlcore: fix a couple small memory leaksDan Carpenter
We should free "chunk" here before returning the error code. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-07-10wlcore: determine AP extra rates correctlyArik Nemtsov
Don't use the ht_mode module parameter for determining AP supported rates. We can rely on channel type, since HT40 won't be enabled if our HT cap doesn't support it. Enable MIMO only if there enough antennas, and rely on per-peer rate limitation to prevent IOPs. Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-07-10wlcore: check ssid length against the correct elementEliad Peller
commit 587cc28 ("wlcore: compare ssid_len before comparing ssids") introduced a new bug - the ssid length from the request struct was compared against the ssid length of another request, instead the one of the cmd. This might cause the sched scan request to fail (with -EINVAL) in many cases. Signed-off-by: Eliad Peller <eliad@wizery.com>
2012-07-10wl12xx/wl18xx: use a dynamic PS timeout of 1.5secArik Nemtsov
It seems some parties have bad user experience when smaller values are used. This should have little implications for power consumption, since traffic is bursty in nature. Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-07-10wlcore: define number of supported bands internallyArik Nemtsov
Avoid using the IEEE80211_NUM_BANDS constant for arrays sizes etc, as this can contain bands unsupported by the driver (e.g. 60Ghz). Use an internal constant to determine the number of bands. Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-07-10wlcore: don't set SDIO_FAILED flag when driver state is offArik Nemtsov
If some IO read/write fails while the FW is not loaded, a recovery will not take place. This means the SDIO_FAILED flag will stay in place forever and prevent further read/writes. This can happen if a check for STATE_OFF was forgotten in some routine. Take this opportunity to rename the flag to IO_FAILED, since we support other buses as well. Reported-by: Ido Yariv <ido@wizery.com> Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-07-10wlcore: change the wait for event mechanismYoni Divinsky
wlcore needs to wait for certain events for example for roc complete event. Usually the events are received from the FW very fast, therefore wlcore can poll with a short delay and if after a second the event was not received yet poll with a long (1-5 msec) delay. This implementation is similar to the sending of commands to the FW. Empirically the change reduced the wait for roc event from ~10-40msec to 100s of usecs. [replace udelay/msleep with usleep_range - Arik] Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com> Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-07-10wlcore: Prevent processing of work items during op_stopIdo Yariv
The interrupt line is disabled in op_stop using disable_irq. Since pending interrupts are synchronized, the mutex has to be released before disabling the interrupt to avoid a deadlock with the interrupt handler. In addition, the internal state of the driver is only set to 'off' after the interrupt is disabled. Otherwise, if an interrupt fires after the state is set but before the interrupt line is disabled, the interrupt handler will not be able to acknowledge the interrupt resulting in an interrupt storm. The driver's operations might be called during recovery. If these acquire the mutex after it was released by op_stop, but before the driver's state is changed, they may queue new work items instead of just failing. This is especially problematic in the case of scans, in which a new scan may be scheduled after all scan requests were cancelled. Signed-off-by: Ido Yariv <ido@wizery.com> Signed-off-by: Arik Nemtsov <arik@wizery.com>
2012-07-10wlcore: implement .flush callbackEliad Peller
implement the .flush() callback by simply calling wl1271_tx_flush(). Signed-off-by: Eliad Peller <eliad@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-07-10wl12xx/wlcore: increase FW filename versionLuciano Coelho
We have some API changes and new features in the new firmwares that are not compatible with older drivers. Increase the version of the FW filenames for wl12xx to 5. Additionally, remove the duplicate definitions from wlcore_i.h and remove the MODULE_FIRMWARE macro calls from the SDIO and SPI modules, since they're irrelevant there. Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-07-10wlcore: add probe request templates for sched and one-shot scansYoni Divinsky
The driver configures the firmware template for probe requests during the scan process. If the same template is used for one-shot and sched scans they will override each other when running scans simultaneously. This fix works only on firmwares later than X.3.9.2.112 for single role and X.3.9.2.23 for multi-role. [Some cleaning-up and renaming of the quirk to something smaller -- Luca.] Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-07-10wlcore: always clear recovery flag during recovery_workArik Nemtsov
If recovery is called when the FW is off, we should clear the recovery flag. Otherwise we risk booting the driver in permanent pending-recovery state. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-07-10wlcore: avoid debug prints during intended FW recoveryArik Nemtsov
Don't read the FW panic log or print other debug data when recovery is intended (i.e. FW type switch). This takes valuable time and can be confusing to the user. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-07-10wlcore: remove recover cmd from testmodeArik Nemtsov
This command is buggy (doesn't take the mutex) and unused. Instead, the "start_recovery" file is used for the same purpose. Remove the code but keep the command constant to avoid breaking the testmode ABI. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-07-10wlcore: don't stop tx queue via watermark if already stoppedArik Nemtsov
If a Tx queue is currently stopped because of our Tx watermark flow control, don't stop it again. This causes a warning to appear. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-07-10wlcore/wl12xx/wl18xx: check min FW versionArik Nemtsov
Refuse to boot if the FW version is too old. The minimum version is set per chip, with the option of setting it per PG in the future. When boot fails because of an old FW, display a helpful message. Signed-off-by: Arik Nemtsov <arik@wizery.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-07-10wlcore: enable sched scan while connectedVictor Goldenshtein
New wl12xx firmware supports scheduled scans also while connected. Stop blocking sched scan requests when connected and add a quirk to block in hardware that don't support it (currently wl18xx doesn't). This requires FW version 6/7.3.10.2.112 for single-role and 6/7.5.6.0.25 for multi-role. Signed-off-by: Victor Goldenshtein <victorg@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com>
2012-07-10udf: Improve table length check to avoid possible overflowJan Kara
When a partition table length is corrupted to be close to 1 << 32, the check for its length may overflow on 32-bit systems and we will think the length is valid. Later on the kernel can crash trying to read beyond end of buffer. Fix the check to avoid possible overflow. CC: stable@vger.kernel.org Reported-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Jan Kara <jack@suse.cz>
2012-07-10Merge branch 'devel-omap5' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/newsoc From Tony Lindgren <tony@atomide.com>: This branch contains minimal support for omap5 to boot to a console without clock framework support. This branch depends on omap-cleanup-part2-for-v3.6. * 'devel-omap5' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: Kconfig update to support additional GPIOs in OMAP5 ARM: OMAP5: Add the build support arm/dts: OMAP5: Add omap5 dts files ARM: OMAP5: board-generic: Add device tree support ARM: omap2+: board-generic: clean up the irq data from board file ARM: OMAP5: Add SMP support ARM: OMAP5: Add the WakeupGen IP updates ARM: OMAP5: l3: Add l3 error handler support for omap5 ARM: OMAP5: gpmc: Update gpmc_init() ARM: OMAP5: timer: Add clocksource, clockevent support ARM: OMAP5: Add minimal support for OMAP5430 SOC ARM: OMAP5: id: Add cpu id for ES versions ARM: OMAP: counter-32k: Select the CR register offset using the IP scheme ARM: OMAP2+: Move stubbed secure_sram_reserve function to a common.c and call it __weak Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-07-10Merge branch 'omap/cleanup2' into next/newsocArnd Bergmann
Dependency for omap/minimal-omap5
2012-07-10mac80211: fix read outside array boundsChristian Lamparter
ieee802_1d_to_ac is defined as a const int[8], but the tid parameter has a range from 0 to 15. Cc: stable@vger.kernel.org Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10NFC: Fix order of arguments to list_add_tail() when queueing HCP framesMathias Jeppsson
The HCP message should be added to transmit queue, not the other way around. Signed-off-by: Mathias Jeppsson <mathias.jeppsson@sonymobile.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10NFC: Fix empty HCI message list checkMathias Jeppsson
list_first_entry() will never return NULL. Instead use list_for_each_entry_safe() to iterate through the list. Signed-off-by: Mathias Jeppsson <mathias.jeppsson@sonymobile.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: John W. Linville <linville@tuxdriver.com>
2012-07-10Merge tag 'omap-devel-am33xx-data-for-v3.6' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/clk From Tony Lindgren <tony@atomide.com>: This branch adds clock data for am33xx. Note that eventually these will use the common clock framework, but those patches are not quite ready yet for omaps. This branch depends on omap-cleanup-part2-for-v3.6 branch. * tag 'omap-devel-am33xx-data-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: OMAP3+: clock33xx: Add AM33XX clock tree data ARM: OMAP3+: clock: Move common clksel_rate & clock data to common file Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2012-07-10Merge branch 'omap/cleanup2' into next/clkArnd Bergmann
Dependency for omap/am33xx-clk branch
2012-07-10of: mtd: nuke useless const qualifierArtem Bityutskiy
This patch does the following: -const int of_get_nand_ecc_mode(struct device_node *np) +int of_get_nand_ecc_mode(struct device_node *np) because: 1. it is probably just a typo? 2. it causes warnings like this when people assing the returned value to an 'int' variable: include/linux/of_mtd.h:14:18: warning: type qualifiers ignored on functi= on return type [-Wignored-qualifiers] Remove also the unnecessary "extern" qualifier to be consistent with other declarations in this file. Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: Rob Herring <rob.herring@calxeda.com>
2012-07-10Merge tag 'omap-cleanup-part2-for-v3.6' of ↵Arnd Bergmann
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup2 From Tony Lindgren <tony@atomide.com>: This branch contains more clean-up like changes and minor fixes for making it easier to support new omap SoCs, such as omap5 and am33xx. This branch has dependencies to earlier clean-up in omap-cleanup-for-v3.6 and omap-devel-dmtimer-for-v3.6 branches, and also depends on the omap-devel-am33xx-for-v3.6 branch, and are based on a merge of these branches. * tag 'omap-cleanup-part2-for-v3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: OMAP: sdrc: Fix the build break for OMAP4 only builds ARM: OMAP2+: dmtimer: cleanup fclk usage ARM: OMAP2+: Fix mismerge for omap_hwmod_get_main_clk() API ARM: OMAP2+: Remove unnecessary ifdef around __omap2_set_globals ARM: OMAP2+: am33xx: Change cpu_is_am33xx to soc_is_am33xx ARM: OMAP2+: am33xx: Make am33xx as a separate class ARM: OMAP2+: Move omap3 dpll ops to dpll3xxx.c ARM: OMAP2+: All OMAP2PLUS uses omap-device.o target so add one entry ARM: OMAP: dmtimer: use devm_ API and do some cleanup in probe() ARM: OMAP2+: hwmod code: add support to set dmadisable in hwmod framework ARM: OMAP2+: PRM/CM: Move the stubbed prm and cm functions to prcm.c file and make them __weak ARM: OMAP2+: hwmod: add omap_hwmod_get_main_clk() API ARM: OMAP3+: dpll: optimize noncore dpll locking logic ARM: OMAP3: control: add definition for CONTROL_CAMERA_PHY_CTRL ARM: OMAP2+: powerdomain code: Fix Wake-up power domain power status ARM: OMAP4: clockdomain/CM code: Update supported transition modes ARM: OMAP3/4: omap_hwmod: Add rstst_offs field to struct omap_hwmod_omap4_prcm ARM: OMAP2+: hwmod: Add new sysc_type3 into omap_hwmod required for am33xx Signed-off-by: Arnd Bergmann <arnd@arndb.de>
generated by cgit (git 2.34.1) at 2025-09-24 16:18:05 +0000