| Age | Commit message (Collapse) | Author |
|---|
|
When EMLSR operation is enabled for an ML Station, EMLSR transition
timeout, padding delay and transition delay should be updated to
Firmware. Above parameters will be used by Firmware to do EMLSR operation
such as sending EML operation mode notification frame, initial control
frame etc.
Obtain above parameters from EML capabilities information present in
ieee80211_sta object and update the same to Firmware in peer assoc WMI
command sent for ML station.
MLO is not enabled in WCN7850 and hence this change is not applicable to
it as of now. This can be a leverage once it is enabled in future.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Ramasamy Kaliappan <quic_rkaliapp@quicinc.com>
Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250327051320.3253783-5-quic_ramess@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
The Linux client assumes that all filehandles are non-volatile for
renames within the same directory (otherwise sillyrename cannot work).
However, the existence of the Linux 'subtree_check' export option has
meant that nfs_rename() has always assumed it needs to flush writes
before attempting to rename.
Since NFSv4 does allow the client to query whether or not the server
exhibits this behaviour, and since knfsd does actually set the
appropriate flag when 'subtree_check' is enabled on an export, it
should be OK to optimise away the write flushing behaviour in the cases
where it is clearly not needed.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
|
|
If there isn't a valid layout, or the layout stateid has changed, the
cleanup after a layout return should clear out the old data.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
If there are still layout segments in the layout plh_return_lsegs list
after a layout return, we should be resetting the state to ensure they
eventually get returned as well.
Fixes: 68f744797edd ("pNFS: Do not free layout segments that are marked for return")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
`pr_cont()` unfortunately does not work here, as other parts of the
Linux kernel log between the two log lines:
[18445.295056] r8152-cfgselector 4-1.1.3: USB disconnect, device number 5
[18445.295112] OOM killer enabled.
[18445.295115] Restarting tasks ...
[18445.295185] usb 3-1: USB disconnect, device number 2
[18445.295193] usb 3-1.1: USB disconnect, device number 3
[18445.296262] usb 3-1.5: USB disconnect, device number 4
[18445.297017] done.
[18445.297029] random: crng reseeded on system resumption
`pr_cont()` also uses the default log level, normally warning, if the
corresponding log line is interrupted.
Therefore, replace the `pr_cont()`, and explicitly log it as a separate
line with log level info:
Restarting tasks: Starting
[…]
Restarting tasks: Done
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://patch.msgid.link/20250511174648.950430-1-pmenzel@molgen.mpg.de
[ rjw: Rebase on top of an earlier analogous change ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux
Merge cpupower utility update for 6.16 from Shuah Khan:
"Adds systemd service to run cpupower and changes binding's makefile
to use -lcpupower.
cpupower: add a systemd service to run cpupower
cpupower: do not write DESTDIR to cpupower.service
cpupower: do not call systemctl at install time
cpupower: do not install files to /etc/default/
cpupower: change binding's makefile to use -lcpupower"
* tag 'linux-cpupower-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux:
cpupower: do not install files to /etc/default/
cpupower: do not call systemctl at install time
cpupower: do not write DESTDIR to cpupower.service
cpupower: change binding's makefile to use -lcpupower
cpupower: add a systemd service to run cpupower
|
|
pm_runtime_put_autosuspend() schedules a hrtimer to expire
at "dev->power.timer_expires". If the hrtimer's callback,
pm_suspend_timer_fn(), observes that the current time equals
"dev->power.timer_expires", it unexpectedly bails out instead of
proceeding with runtime suspend.
pm_suspend_timer_fn():
if (expires > 0 && expires < ktime_get_mono_fast_ns()) {
dev->power.timer_expires = 0;
rpm_suspend(..)
}
Additionally, as ->timer_expires is not cleared, all the future auto
suspend requests will not schedule hrtimer to perform auto suspend.
rpm_suspend():
if ((rpmflags & RPM_AUTO) &&...) {
if (!(dev->power.timer_expires && ...) { <-- this will fail.
hrtimer_start_range_ns(&dev->power.suspend_timer,...);
}
}
Fix this by as well checking if current time reaches the set expiration.
Co-developed-by: Patrick Daly <quic_pdaly@quicinc.com>
Signed-off-by: Patrick Daly <quic_pdaly@quicinc.com>
Signed-off-by: Charan Teja Kalla <quic_charante@quicinc.com>
Link: https://patch.msgid.link/20250515064125.1211561-1-quic_charante@quicinc.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Since dynamic VLAN traffic is software encrypted and encapsulated,
mac80211 handles the duplication on each link for MLO dynamic VLAN
multicast.
Currently in ath12k_mac_op_tx(), all multicast frames are duplicated
and are assigned a mcbc_gsn. This is causing dynamic VLAN multicast
traffic to be dropped in hardware.
Prevent dynamic VLAN multicast traffic from being duplicated again in
the driver. Check if incoming packet is a dynamic VLAN packet and
avoid defaulting to multicast conditional.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Muna Sinada <muna.sinada@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250424221404.1262597-1-muna.sinada@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, TCL performs the TX address search for each entry during
transmission, which may lead to packet delays.
To mitigate this issue, enable AST index-based address search during
transmission in station mode. This AST index-based search is not
enabled in AP mode due to the complexity involved in fetching peer
information.
Implement changes to retrieve the offset of ast_idx/ast_hash values
from the PEER_MAP3 event, update the vdev search type to ADDRX, and
enable AST lookup in the bank configuration.
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Thiraviyam Mariyappan <quic_tmariyap@quicinc.com>
Signed-off-by: Nithyanantham Paramasivam <nithyanantham.paramasivam@oss.qualcomm.com>
Reviewed-by: Mahendran P <quic_mahep@quicinc.com>
Link: https://patch.msgid.link/20250422094255.131226-1-nithyanantham.paramasivam@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Enable monitor mode for WCN7850.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-14-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
In ath12k_dp_mon_rx_merg_msdus(), will set packet offset to 8. This is a
right value for QCN9274.
But WCN7850 use different hardware rings for monitor mode because it
doesn't have RX MON component. So the packet offset is different. With
current offset, upper-layer application will failed to parse the payload
correctly.
Should use different value for those who don't have RX MON component.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-13-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Some monitor parameters are only initialized for QCN9274, but WCN7850
also needs them, so initialize them for WCN7850 as well.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-12-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
WCN7850 uses error dst ring as mon dest ring. Each time hardware
receives a packet, will fill the payload into mon dest ring.
The mon dest ring may store many MSDUs, which belonged to different
MPDUs. Need to retrieve MSDUs based on the PPDU ID, only processing the
MSDUs with same PPDU ID each time.
The PPDU ID is used in cycles, the difference between the PPDU IDs
of the two rings must be checked. If the status PPDU ID minus the
dest PPDU ID is greater than 20000, it is considered a wrap-around
case.
After reaping the mon dest ring, should prepare packet and deliver it to
mac80211 when status PPDU ID is equal to dest PPDU ID. Then start to
process next PPDU if exists.
But if dest PPDU ID > status PPDU ID, should hold on to mon dest ring
processing. If it exceeds 16 consecutive times, status PPDU ID will be
forcibly set to dest PPDU ID to avoid backpressure issue.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-11-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, ath12k_dp_rx_link_desc_return() takes struct
hal_reo_dest_ring as its second input. This struct is converted to
struct hal_wbm_release_ring and passed into
ath12k_hal_rx_msdu_link_desc_set(), where it is converted again.
This double conversion is both strange and inefficient.
In ath12k_hal_rx_msdu_link_desc_set(), only buf_addr_info is actually
used. To simplify the code and improve readability, directly passes
buf_addr_info when calling ath12k_dp_rx_link_desc_return().
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-10-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, HAL_RX_MSDU_PKT_LENGTH_GET uses u32_get_bits to obtain the
MSDU length from the MSDU description.
This is not right. Because all halphy descriptions are little endian.
So use le32_get_bits for HAL_RX_MSDU_PKT_LENGTH_GET.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-9-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
WCN7850 uses monitor status ring to store status buffer. Status buffer
contains many TLVs such as MPDU START/END. From these TLVs, can get
necessary information about related payload, such as PPDU ID.
Add helper function to reap status buffer from monitor status ring so
that can parse TLVs later by ath12k_dp_mon_parse_rx_dest().
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-8-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Monitor status ring interrupt is configured in previous patch. So add
handler function __ath12k_dp_mon_process_ring() for monitor mode.
Will implement detail processing in patch 7 and 10.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-7-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
The monitor mode design is:
1. Hardware captures packets on the air.
2. Hardware stores the packets into related rings.
3. When the ring buffer reaches the interrupt threshold, it triggers
the interrupt.
4. Reap and process the ring buffer in ath12k_dp_service_srng().
Here the interrupt thresholds are intr_timer_thres_us, low_threshold and
intr_batch_cntr_thres_entries. An interrupt will be triggered once:
1. Number of packets in the ring reaches intr_batch_cntr_thres_entries.
2. Number of packets in the ring reaches low_threshold(by timer).
3. Timer reaches intr_timer_thres_us.
So, add interrupt configuration for the mon status ring, then start
to process ring buffers when the interrupt arrives.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-6-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
For WCN7850, it doesn't have an RX MON component(RX MON dest ring and
RX MON buffer ring). So it can only reuse the mon status ring, RX
refill ring, and error dst ring for monitor mode.
Every time the hardware captures a packet, it will store status
information into the status ring and store the MSDU payload buffer
address into the error dst ring. When host reaps the MSDU payload and
consumes a buffer, it will replenish the RX refill ring to indicate a
new buffer.
The configuration of the error dst/RX ring already exists. But there is
no configuration for mon status ring. So add ring configuration for it.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-5-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, the hw_srng_config_template does not have a template for mon
status ring.
But srng config template is necessary during ring initialization. So add
a template for mon status ring.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-4-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
WCN7850 doesn't have RX MON component. So it's monitor mode design is
quite different from AP based chips like QCN9274, which have RX MON
component.
ath12k_dp_mon_parse_rx_dest_tlv() is such a specific function for AP based
chips.
So don't call this function for WCN7850.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-3-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently, error bitmap and decap format are parsed in
ath12k_dp_mon_parse_rx_dest_tlv(). Then stored into dp_rx_mon_mpdu_list.
ath12k_dp_mon_parse_rx_dest_tlv() and dp_rx_mon_mpdu_list are only used
by QCN9274.
For WCN7850, error bitmap and decap format are also needed. So need to
parse MSDU END TLV in ath12k_dp_mon_rx_parse_status_tlv(), this is the
common function for WCN7850 and QCN9274. Then store error bitmap and
decap format so that QCN9274 can fetch them when processing MSDU payload.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250421023444.1778-2-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
deletion
Currently, when ath12k performs the remove link interface operation, if
there is an ongoing scan operation on the arvif, ath12k may execute the
remove link interface operation multiple times on the same arvif. This
occurs because, during the remove link operation, if a scan operation is
present on the arvif, ath12k may receive a WMI_SCAN_EVENT_COMPLETED event
from the firmware. Upon receiving this event, ath12k will continue to
execute the ath12k_scan_vdev_clean_work() function, performing the remove
link interface operation on the same arvif again.
To address this issue, before executing the remove link interface
operation, ath12k needs to check if there is an ongoing scan operation on
the current arvif. If such an operation exists, it should be aborted.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com>
Tested-by: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418064008.7172-1-quic_lingbok@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
6 GHz
When station is connected to a 6 GHz AP, there are 2 ways to configure the
power limit to firmware. The first way is to send 2 WMI commands
WMI_PDEV_PARAM_TXPOWER_LIMIT2G/WMI_PDEV_PARAM_TXPOWER_LIMIT5G to firmware,
the second way is to send WMI_VDEV_SET_TPC_POWER_CMDID to firmware which
includes more parameters for power control.
When firmware advertises WMI_TLV_SERVICE_EXT_TPC_REG_SUPPORT, it supports
WMI_VDEV_SET_TPC_POWER_CMDID, ath12k uses it to send more parameters to
firmware. As chanctx is needed to extract necessary info for this command,
save it beforehand in ath12k_mac_op_assign_vif_chanctx().
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-15-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add the handler for WMI_VDEV_SET_TPC_POWER_CMDID, it is for 6 GHz band.
A subsequent patch will call this handler to send power parameters to
firmware.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-14-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Prepare the parameters which are needed for WMI command
WMI_VDEV_SET_TPC_POWER_CMDID. This helper will be used in a following
patch.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-13-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Save the max transmit power received in the vdev start response event from
firmware. A subsequent patch will use this to calculate the final power
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-12-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
The Transmit Power Envelope element conveys the local maximum transmit
power for various transmission bandwidths, this element is present in
various frames, e.g. beacon and probe response etc, transmitted by AP.
A station shall determine a local maximum transmit power from it.
So parse and save them for later use.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-11-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently the power spectral density (PSD) report from firmware is ignored.
Since it is needed by cfg80211, report it in struct ieee80211_reg_rule such
that cfg80211 can use it.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-10-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Once connection to AP established we know the exact power type, it is time
to update regulatory rules based on such info.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-9-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
There are two power types for 6 GHz regulatory, one is AP, another is
client. The client power type is used for station interface, and AP
power type is used for AP/mesh point interface.
When firmware boots up, WMI_REG_CHAN_LIST_CC_EXT_EVENTID is sent from
firmware at an early stage, the interface mode is not decided at this
point, then ath12k select reg rules of AP type as default.
After interface created, ath12k needs to update reg rules to the exact
power type matching the interface type.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-8-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently interface mode is determined each time a vdev is created.
In MLO scenario where there could be multiple vdevs this is just a
waste of time.
Move related logic into a new helper ath12k_mac_determine_vdev_type()
and call it once in ath12k_mac_op_add_interface().
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-7-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently we only build regdomain when channel list event is received.
That event is received when driver boots or when a new country code is
sent to firmware. At either time we may have no information about
interface mode or AP's power type, consequently WMI_REG_INDOOR_AP is
selected. In upcoming patches we will rebuild regdomain once those
information is available. For that purpose reg info has to be
stored/refreshed each time a new channel list event is received.
The stored reg info would be freed in ath12k_reg_free() when it is not
needed.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-6-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
The reg info is allocated in ath12k_reg_chan_list_event() but validated
in ath12k_reg_handle_chan_list(). Currently this is good since reg info
would be freed regardless of validation results. However in an upcoming
patch the reg info might need to be stored for later use if the result
is good. Since we can not tell the result from return value of
ath12k_reg_handle_chan_list(), we need to move validation out of it.
Add a new helper ath12k_reg_validate_reg_info() and call it in
ath12k_reg_chan_list_event(), based on the result we can choose to store
or free it in the following patch.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-5-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
For 6 GHz band, firmware offers 3 types of regulatory rules for AP
mode and 6 for station mode in WMI_REG_CHAN_LIST_CC_EXT_EVENTID event.
In ath12k_reg_build_regd() current code by default chooses
WMI_REG_INDOOR_AP type rules from AP mode reg list to build regdomain,
regardless of the interface mode and power type, hence is not correct.
Pass interface mode (wmi_vdev_type) and AP power type
(ieee80211_ap_reg_power) as new arguments to ath12k_reg_build_regd()
such that we can choose correct rules based on them. Currently
ath12k_reg_build_regd() is called only by ath12k_reg_chan_list_event()
when driver boots, at that time these two arguments are not determined
yet, hence by default pass WMI_VDEV_TYPE_UNSPEC and
IEEE80211_REG_UNSET_AP, this results in WMI_REG_INDOOR_AP being chosen
at last. In upcoming patches the rules would be updated when these two
arguments could be determined.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-4-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently we pass intersect flag to tell ath12k_reg_build_regd() whether
regulatory rulse are intersected. This flag is determined in
ath12k_reg_handle_chan_list() and has no other users.
Move related logic into ath12k_reg_build_regd() to make code clear. Also
relocate ath12k_reg_is_world_alpha() to avoid forward declaration, and
refine it for code simplicity.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-3-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
ath12k_reg_chan_list_event() is doing quite some work: allocate/free
reg_info, parse chan list event and store required info in reg_info,
process reg_info, build regd and queue work item for later processing
etc, which makes it hard to read.
Refactor this function:
1. extract reg_info processing and regd building into a new helper
ath12k_reg_handle_chan_list().
2. extract reg_info free into a new helper ath12k_reg_reset_reg_info().
Note the refactor also benefit some upcoming patches where these helpers
are getting called.
Also relocate these two helpers and the existing
ath12k_reg_is_world_alpha() to reg.c to reflect what they are doing.
And update fw to firmware while relocating.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-2-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
spin_lock/spin_unlock are used in ath12k_reg_chan_list_event
to acquire/release ab->base_lock. For now this is safe because
that function is only called in soft IRQ context.
But ath12k_reg_chan_list_event() will be called from process
context in an upcoming patch, and this can result in a deadlock
if ab->base_lock is acquired in process context and then soft
IRQ occurs on the same CPU and tries to acquire that lock.
Fix it by using spin_lock_bh and spin_unlock_bh instead.
Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3
Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250418-ath12k-6g-lp-vlp-v1-1-c869c86cad60@quicinc.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Currently mon reap timer is not used, and it is not needed anymore for
WCN7850.
So remove related code.
This change does not affect QCN9274, as the mon reap timer is not used
for QCN9274.
Signed-off-by: Kang Yang <kang.yang@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250416022011.1935-1-kang.yang@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
Add debugfs support to simulate firmware crash to test firmware restart.
Usage:
-----
echo assert > /sys/kernel/debug/ath12k/pci-0000\:58\:00.0/simulate_fw_crash
Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1
Signed-off-by: Dinesh Karthikeyan <quic_dinek@quicinc.com>
Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com>
Signed-off-by: Maharaja Kennadyrajan <maharaja.kennadyrajan@oss.qualcomm.com>
Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com>
Link: https://patch.msgid.link/20250417065237.2507613-1-maharaja.kennadyrajan@oss.qualcomm.com
Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
|
|
In an effort to move ARM64 away from the legacy MSI setup, convert the
Tegra PCIe driver to the MSI-parent infrastructure and let each device have
its own MSI domain.
[ tglx: Moved the struct out of the function call argument ]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250513172819.2216709-10-maz@kernel.org
|
|
In an effort to move ARM64 away from the legacy MSI setup, convert the
XGENE PCIe driver to the MSI-parent infrastructure and let each device have
its own MSI domain.
[ tglx: Moved the struct out of the function call argument ]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250513172819.2216709-9-maz@kernel.org
|
|
In an effort to move ARM64 away from the legacy MSI setup, convert the
Apple PCIe driver to the MSI-parent infrastructure and let each device have
its own MSI domain.
[ tglx: Moved the struct out of the function call argument ]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Link: https://lore.kernel.org/all/20250513172819.2216709-8-maz@kernel.org
|
|
Bad MSI implementations multiplex MSIs onto a single downstream interrupt,
meaning they have no concept of individual affinity.
The old MSI code did a reasonable job at this by honouring the
MSI_FLAG_NO_AFFINITY, but the new shiny device MSI code doesn't.
Teach it about the sad reality of existing hardware.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250513172819.2216709-7-maz@kernel.org
|
|
Switch the MVEBU family of interrupt chip drivers over to the common helper
function to create the interrupt domains.
[ tglx: Moved the struct out of the function call argument and fix up
the of_node_to_fwnode() instances ]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250513172819.2216709-5-maz@kernel.org
|
|
Switch the GIC family of interrupt chip drivers over to the common helper
function to create the interrupt domains.
[ tglx: Moved the struct out of the function call argument ]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250513172819.2216709-4-maz@kernel.org
|
|
Creating an irq domain that serves as an MSI parent requires
a substantial amount of esoteric boiler-plate code, some of
which is often provided twice (such as the bus token).
To make things a bit simpler for the unsuspecting MSI tinkerer,
provide a helper that does it for them, and serves as documentation
of what needs to be provided.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250513172819.2216709-3-maz@kernel.org
|
|
Move irq-msi-lib.h into include/linux/irqchip, making it available
to compilation units outside of drivers/irqchip.
This requires some churn in drivers to fetch it from the new location,
generated using this script:
git grep -l -w \"irq-msi-lib.h\" | \
xargs sed -i -e 's:"irq-msi-lib.h":\<linux/irqchip/irq-msi-lib.h\>:'
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250513172819.2216709-2-maz@kernel.org
|
|
Pick up the PCI changes to avoid conflicts.
|
|
Now that the file has been thrown through the mincer, finish the job and
consolidate the coding style.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
