| Age | Commit message (Collapse) | Author |
|---|
|
Semicolon is not required at the end of switch block. So, remove it.
Addresses coccinelle warning:
drivers/net/ethernet/chelsio/cxgb4/sge.c:2260:2-3: Unneeded semicolon
Fixes: 4846d5330daf ("cxgb4: add Tx and Rx path for ETHOFLD traffic")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The taprio qdisc allows to set mqprio setting but only once. In case
if mqprio settings are provided next time the error is returned as
it's not allowed to change traffic class mapping in-flignt and that
is normal. But if configuration is absolutely the same - no need to
return error. It allows to provide same command couple times,
changing only base time for instance, or changing only scheds maps,
but leaving mqprio setting w/o modification. It more corresponds the
message: "Changing the traffic mapping of a running schedule is not
supported", so reject mqprio if it's really changed.
Also corrected TC_BITMASK + 1 for consistency, as proposed.
Fixes: a3d43c0d56f1 ("taprio: Add support adding an admin schedule")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Vinicius Costa Gomes <vinicius.gomes@intel.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On the NXP LS1028A, there are 2 Ethernet links between the Felix switch
and the ENETC:
- eno2 <-> swp4, at 2.5G
- eno3 <-> swp5, at 1G
Only one of the above Ethernet port pairs can act as a DSA link for
tagging.
When adding initial support for the driver, it was tested only on the 1G
eno3 <-> swp5 interface, due to the necessity of using PHYLIB initially
(which treats fixed-link interfaces as emulated C22 PHYs, so it doesn't
support fixed-link speeds higher than 1G).
After making PHYLINK work, it appears that swp4 still can't act as CPU
port. So it looks like ocelot_set_cpu_port was being called for swp4,
but then it was called again for swp5, overwriting the CPU port assigned
in the DT.
It appears that when you call dsa_upstream_port for a port that is not
defined in the device tree (such as swp5 when using swp4 as CPU port),
its dp->cpu_dp pointer is not initialized by dsa_tree_setup_default_cpu,
and this trips up the following condition in dsa_upstream_port:
if (!cpu_dp)
return port;
So the moral of the story is: don't call dsa_upstream_port for a port
that is not defined in the device tree, and therefore its dsa_port
structure is not completely initialized (ds->num_ports is still 6).
Fixes: 56051948773e ("net: dsa: ocelot: add driver for Felix switch family")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bring back tls_sw_sendpage_locked. sk_msg redirection into a socket
with TLS_TX takes the following path:
tcp_bpf_sendmsg_redir
tcp_bpf_push_locked
tcp_bpf_push
kernel_sendpage_locked
sock->ops->sendpage_locked
Also update the flags test in tls_sw_sendpage_locked to allow flag
MSG_NO_SHARED_FRAGS. bpf_tcp_sendmsg sets this.
Link: https://lore.kernel.org/netdev/CA+FuTSdaAawmZ2N8nfDDKu3XLpXBbMtcCT0q4FntDD2gn8ASUw@mail.gmail.com/T/#t
Link: https://github.com/wdebruij/kerneltools/commits/icept.2
Fixes: 0608c69c9a80 ("bpf: sk_msg, sock{map|hash} redirect through ULP")
Fixes: f3de19af0f5b ("Revert \"net/tls: remove unused function tls_sw_sendpage_locked\"")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When relocating subprogram call, libbpf doesn't take into account
relo->text_off, which comes from symbol's value. This generally works fine for
subprograms implemented as static functions, but breaks for global functions.
Taking a simplified test_pkt_access.c as an example:
__attribute__ ((noinline))
static int test_pkt_access_subprog1(volatile struct __sk_buff *skb)
{
return skb->len * 2;
}
__attribute__ ((noinline))
static int test_pkt_access_subprog2(int val, volatile struct __sk_buff *skb)
{
return skb->len + val;
}
SEC("classifier/test_pkt_access")
int test_pkt_access(struct __sk_buff *skb)
{
if (test_pkt_access_subprog1(skb) != skb->len * 2)
return TC_ACT_SHOT;
if (test_pkt_access_subprog2(2, skb) != skb->len + 2)
return TC_ACT_SHOT;
return TC_ACT_UNSPEC;
}
When compiled, we get two relocations, pointing to '.text' symbol. .text has
st_value set to 0 (it points to the beginning of .text section):
0000000000000008 000000050000000a R_BPF_64_32 0000000000000000 .text
0000000000000040 000000050000000a R_BPF_64_32 0000000000000000 .text
test_pkt_access_subprog1 and test_pkt_access_subprog2 offsets (targets of two
calls) are encoded within call instruction's imm32 part as -1 and 2,
respectively:
0000000000000000 test_pkt_access_subprog1:
0: 61 10 00 00 00 00 00 00 r0 = *(u32 *)(r1 + 0)
1: 64 00 00 00 01 00 00 00 w0 <<= 1
2: 95 00 00 00 00 00 00 00 exit
0000000000000018 test_pkt_access_subprog2:
3: 61 10 00 00 00 00 00 00 r0 = *(u32 *)(r1 + 0)
4: 04 00 00 00 02 00 00 00 w0 += 2
5: 95 00 00 00 00 00 00 00 exit
0000000000000000 test_pkt_access:
0: bf 16 00 00 00 00 00 00 r6 = r1
===> 1: 85 10 00 00 ff ff ff ff call -1
2: bc 01 00 00 00 00 00 00 w1 = w0
3: b4 00 00 00 02 00 00 00 w0 = 2
4: 61 62 00 00 00 00 00 00 r2 = *(u32 *)(r6 + 0)
5: 64 02 00 00 01 00 00 00 w2 <<= 1
6: 5e 21 08 00 00 00 00 00 if w1 != w2 goto +8 <LBB0_3>
7: bf 61 00 00 00 00 00 00 r1 = r6
===> 8: 85 10 00 00 02 00 00 00 call 2
9: bc 01 00 00 00 00 00 00 w1 = w0
10: 61 62 00 00 00 00 00 00 r2 = *(u32 *)(r6 + 0)
11: 04 02 00 00 02 00 00 00 w2 += 2
12: b4 00 00 00 ff ff ff ff w0 = -1
13: 1e 21 01 00 00 00 00 00 if w1 == w2 goto +1 <LBB0_3>
14: b4 00 00 00 02 00 00 00 w0 = 2
0000000000000078 LBB0_3:
15: 95 00 00 00 00 00 00 00 exit
Now, if we compile example with global functions, the setup changes.
Relocations are now against specifically test_pkt_access_subprog1 and
test_pkt_access_subprog2 symbols, with test_pkt_access_subprog2 pointing 24
bytes into its respective section (.text), i.e., 3 instructions in:
0000000000000008 000000070000000a R_BPF_64_32 0000000000000000 test_pkt_access_subprog1
0000000000000048 000000080000000a R_BPF_64_32 0000000000000018 test_pkt_access_subprog2
Calls instructions now encode offsets relative to function symbols and are both
set ot -1:
0000000000000000 test_pkt_access_subprog1:
0: 61 10 00 00 00 00 00 00 r0 = *(u32 *)(r1 + 0)
1: 64 00 00 00 01 00 00 00 w0 <<= 1
2: 95 00 00 00 00 00 00 00 exit
0000000000000018 test_pkt_access_subprog2:
3: 61 20 00 00 00 00 00 00 r0 = *(u32 *)(r2 + 0)
4: 0c 10 00 00 00 00 00 00 w0 += w1
5: 95 00 00 00 00 00 00 00 exit
0000000000000000 test_pkt_access:
0: bf 16 00 00 00 00 00 00 r6 = r1
===> 1: 85 10 00 00 ff ff ff ff call -1
2: bc 01 00 00 00 00 00 00 w1 = w0
3: b4 00 00 00 02 00 00 00 w0 = 2
4: 61 62 00 00 00 00 00 00 r2 = *(u32 *)(r6 + 0)
5: 64 02 00 00 01 00 00 00 w2 <<= 1
6: 5e 21 09 00 00 00 00 00 if w1 != w2 goto +9 <LBB2_3>
7: b4 01 00 00 02 00 00 00 w1 = 2
8: bf 62 00 00 00 00 00 00 r2 = r6
===> 9: 85 10 00 00 ff ff ff ff call -1
10: bc 01 00 00 00 00 00 00 w1 = w0
11: 61 62 00 00 00 00 00 00 r2 = *(u32 *)(r6 + 0)
12: 04 02 00 00 02 00 00 00 w2 += 2
13: b4 00 00 00 ff ff ff ff w0 = -1
14: 1e 21 01 00 00 00 00 00 if w1 == w2 goto +1 <LBB2_3>
15: b4 00 00 00 02 00 00 00 w0 = 2
0000000000000080 LBB2_3:
16: 95 00 00 00 00 00 00 00 exit
Thus the right formula to calculate target call offset after relocation should
take into account relocation's target symbol value (offset within section),
call instruction's imm32 offset, and (subtracting, to get relative instruction
offset) instruction index of call instruction itself. All that is shifted by
number of instructions in main program, given all sub-programs are copied over
after main program.
Convert few selftests relying on bpf-to-bpf calls to use global functions
instead of static ones.
Fixes: 48cca7e44f9f ("libbpf: add support for bpf_call")
Reported-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Yonghong Song <yhs@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191119224447.3781271-1-andriin@fb.com
|
|
In afs_wait_for_call_to_complete(), rather than immediately aborting an
operation if a signal occurs, the code attempts to wait for it to
complete, using a schedule timeout of 2*RTT (or min 2 jiffies) and a
check that we're still receiving relevant packets from the server before
we consider aborting the call. We may even ping the server to check on
the status of the call.
However, there's a missing timeout reset in the event that we do
actually get a packet to process, such that if we then get a couple of
short stalls, we then time out when progress is actually being made.
Fix this by resetting the timeout any time we get something to process.
If it's the failure of the call then the call state will get changed and
we'll exit the loop shortly thereafter.
A symptom of this is data fetches and stores failing with EINTR when
they really shouldn't.
Fixes: bc5e3a546d55 ("rxrpc: Use MSG_WAITALL to tell sendmsg() to temporarily ignore signals")
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Marc Dionne <marc.dionne@auristor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Drivers use different fields to report the number of channels, so take
the maximum of all data channels (rx, tx, combined) when determining the
size of the xsk map. The current code used only 'combined' which was set
to 0 in some drivers e.g. mlx4.
Tested: compiled and run xdpsock -q 3 -r -S on mlx4
Signed-off-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/bpf/20191119001951.92930-1-lrizzo@google.com
|
|
The previous commit had a bug where the last page in the memory range
could not be synced. This change fixes the behavior so that all the
required pages are synced.
Fixes: 9cfeeb576d49 ("gve: Fixes DMA synchronization")
Signed-off-by: Adi Suresh <adisuresh@google.com>
Reviewed-by: Catherine Sullivan <csully@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For our current users we don't expect pool objects to be writable from
the gpu.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Fixes: 4f7af1948abc ("drm/i915: Support ro ppgtt mapped cmdparser shadow buffers")
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20191119150154.18249-1-matthew.auld@intel.com
(cherry picked from commit d18580b08b92ec4105eb0ede2d676e8b1f5a66c3)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
LDO9 and LDO10 were listed with the same enable bits.
That looks insane and there are no provisions in the code for handling such
a special case. Also other out-of-tree drivers use a separate bit to
enable it.
Example:
https://github.com/brunotl/kernel-kobo-mx6sl-ntx/blob/master/drivers/regulator/ricoh619-regulator.c
So it seems to be clearly a bug.
I cannot fully check it on my board without schematics and just discovered
this during code analysis for another problem.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Link: https://lore.kernel.org/r/20191113182643.23885-1-andreas@kemnade.info
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit 1d4639567d97 ("mdio_bus: Fix PTR_ERR applied after initialization
to constant") accidentally changed a check from -ENOTSUPP to -ENOSYS,
causing failures if reset controller support is not enabled. E.g. on
r7s72100/rskrza1:
sh-eth e8203000.ethernet: MDIO init failed: -524
sh-eth: probe of e8203000.ethernet failed with error -524
Seen on r8a7740/armadillo, r7s72100/rskrza1, and r7s9210/rza2mevb.
Fixes: 1d4639567d97 ("mdio_bus: Fix PTR_ERR applied after initialization to constant")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: YueHaibing <yuehaibing@huawei.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Before returning NULL, put the sock first.
Cc: stable@vger.kernel.org
Fixes: cf1b2326b734 ("nbd: verify socket is supported during setup")
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Sun Ke <sunke32@huawei.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Both init functions have a stray "return NULL" at the end which is never
reached so drop them.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191119125837.47619-1-mika.westerberg@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When we hot unplug a virtserialport and then try to hot plug again,
it fails:
(qemu) chardev-add socket,id=serial0,path=/tmp/serial0,server,nowait
(qemu) device_add virtserialport,bus=virtio-serial0.0,nr=2,\
chardev=serial0,id=serial0,name=serial0
(qemu) device_del serial0
(qemu) device_add virtserialport,bus=virtio-serial0.0,nr=2,\
chardev=serial0,id=serial0,name=serial0
kernel error:
virtio-ports vport2p2: Error allocating inbufs
qemu error:
virtio-serial-bus: Guest failure in adding port 2 for device \
virtio-serial0.0
This happens because buffers for the in_vq are allocated when the port is
added but are not released when the port is unplugged.
They are only released when virtconsole is removed (see a7a69ec0d8e4)
To avoid the problem and to be symmetric, we could allocate all the buffers
in init_vqs() as they are released in remove_vqs(), but it sounds like
a waste of memory.
Rather than that, this patch changes add_port() logic to ignore ENOSPC
error in fill_queue(), which means queue has already been filled.
Fixes: a7a69ec0d8e4 ("virtio_console: free buffers after reset")
Cc: mst@redhat.com
Cc: stable@vger.kernel.org
Signed-off-by: Laurent Vivier <lvivier@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Commit 780bc7903a32 ("virtio_ring: Support DMA APIs") makes
virtqueue_add() return -EIO when we fail to map our I/O buffers. This is
a very realistic scenario for guests with encrypted memory, as swiotlb
may run out of space, depending on it's size and the I/O load.
The virtio-blk driver interprets -EIO form virtqueue_add() as an IO
error, despite the fact that swiotlb full is in absence of bugs a
recoverable condition.
Let us change the return code to -ENOMEM, and make the block layer
recover form these failures when virtio-blk encounters the condition
described above.
Cc: stable@vger.kernel.org
Fixes: 780bc7903a32 ("virtio_ring: Support DMA APIs")
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Tested-by: Michael Mueller <mimu@linux.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
We used to take a lock in amp_physical_cfm() but then we moved it to
the caller function. Unfortunately the unlock on this error path was
overlooked so it leads to a double unlock.
Fixes: a514b17fab51 ("Bluetooth: Refactor locking in amp_physical_cfm")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add the device ID for the WiFi/BT/FM combo chip BCM4334 (rev B0).
The chip seems to use 43:34:b0:00:00:00 as default address,
so add it to the list of default addresses and leave it up
to the user to configure a valid one.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Ilya Leoshkevich says:
====================
This patch series introduces usage of relative long jumps and loads in
order to lift 64/512k size limits on JITed BPF programs on s390.
Patch 1 introduces long relative branches.
Patch 2 changes the way literal pool is arranged in order to be
compatible with long relative loads.
Patch 3 changes the way literal pool base register is loaded for large
programs.
Patch 4 replaces regular loads with long relative loads where they are
totally superior.
Patch 5 introduces long relative loads as an alternative way to load
constants in large programs. Regular loads are kept and still used for
small programs.
Patch 6 removes the size limit check.
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Now that jump and long displacement ranges are no longer a problem,
remove the limit on JITed image size. In practice it's still limited by
2G, but with verifier allowing "only" 1M instructions, it's not an
issue.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191118180340.68373-7-iii@linux.ibm.com
|
|
If literal pool grows past 524287 mark, it's no longer possible to use
long displacement to reference literal pool entries. In JIT setting
maintaining multiple literal pool registers is next to impossible, since
we operate on one instruction at a time.
Therefore, fall back to loading literal pool entry using PC-relative
addressing, and then using a register-register form of the following
machine instruction.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191118180340.68373-6-iii@linux.ibm.com
|
|
lg and lgrl have the same performance characteristics, but the former
requires a base register and is subject to long displacement range
limits, while the latter does not. Therefore, lgrl is totally superior
to lg and should be used instead whenever possible.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191118180340.68373-5-iii@linux.ibm.com
|
|
Currently literal pool register is loaded using basr, which makes it
point not to the beginning of the literal pool, but rather to the next
instruction. In case JITed code is larger than 512k, this renders
literal pool register absolutely useless due to long displacement range
restrictions.
The solution is to use larl to make literal pool register point to the
very beginning of the literal pool. This makes it always possible to
address 512k worth of literal pool entries using long displacement.
However, for short programs, in which the entire literal pool is covered
by basr-generated base, it is still beneficial to use basr, since it is
4 bytes shorter than larl.
Detect situations when basr-generated base does not cover the entire
literal pool, and in such cases use larl instead.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191118180340.68373-4-iii@linux.ibm.com
|
|
When literal pool size exceeds 512k, it's no longer possible to
reference all the entries in it using a single base register and long
displacement. Therefore, PC-relative lgfrl and lgrl instructions need to
be used.
Unfortunately, they require their arguments to be aligned to 4- and
8-byte boundaries respectively. This generates certain overhead due to
necessary padding bytes. Grouping 4- and 8-byte entries together reduces
the maximum overhead to 6 bytes (2 for aligning 4-byte entries and 4 for
aligning 8-byte entries).
While in theory it is possible to detect whether or not alignment is
needed by comparing the literal pool size with 512k, in practice this
leads to having two ways of emitting constants, making the code more
complicated.
Prefer code simplicity over trivial size saving, and always group and
align literal pool entries.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191118180340.68373-3-iii@linux.ibm.com
|
|
Currently maximum JITed code size is limited to 64k, because JIT can
emit only relative short branches, whose range is limited by 64k in both
directions.
Teach JIT to use relative long branches. There are no compare+branch
relative long instructions, so using relative long branches consumes
more space due to having to having to emit an explicit comparison
instruction. Therefore do this only when relative short branch is not
enough.
Signed-off-by: Ilya Leoshkevich <iii@linux.ibm.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191118180340.68373-2-iii@linux.ibm.com
|
|
The error return path on when bpf_fentry_test* tests fail does not
kfree 'data'. Fix this by adding the missing kfree.
Addresses-Coverity: ("Resource leak")
Fixes: faeb2dce084a ("bpf: Add kernel test functions for fentry testing")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20191118114059.37287-1-colin.king@canonical.com
|
|
When CONFIG_RESET_CONTROLLER is disabled, the
devm_reset_control_get_exclusive function returns -ENOTSUPP. This is not
handled in subsequent check and then the mdio device fails to probe.
When CONFIG_RESET_CONTROLLER is enabled, its code checks in OF for reset
device, and since it is not present, returns -ENOENT. -ENOENT is handled.
Add -ENOTSUPP also.
This happened to me when upgrading kernel on Turris Omnia. You either
have to enable CONFIG_RESET_CONTROLLER or use this patch.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Fixes: 71dd6c0dff51b ("net: phy: add support for reset-controller")
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit eec4844fae7c ("proc/sysctl: add shared variables for range
check") did:
- .extra2 = &two,
+ .extra2 = SYSCTL_ONE,
here, which doesn't seem to be intentional, given the changelog.
This patch restores it to the previous, as the value of 2 still makes
sense (used in fib_multipath_hash()).
Fixes: eec4844fae7c ("proc/sysctl: add shared variables for range check")
Cc: Matteo Croce <mcroce@redhat.com>
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: Matteo Croce <mcroce@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the case where the call to phy_interface_is_rgmii returns zero
the variable ret is left uninitialized and this is returned at
the end of the function dp83869_configure_rgmii. Fix this by
returning 0 instead of the uninitialized value in ret.
Addresses-Coverity: ("Uninitialized scalar variable")
Fixes: 01db923e8377 ("net: phy: dp83869: Add TI dp83869 phy")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver forgets to disable the regulator in remove like what is done
in probe failure.
Add the missed call to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
LWTUNNEL_IP_OPT_ERSPAN_VER is u8 type, and nla_put_u8 should have
been used instead of nla_put_u32(). This is a copy-paste error.
Fixes: b0a21810bd5e ("lwtunnel: add options setting and dumping for erspan")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
XDP_TX rings should not be limited by max_num_tx_rings_p_up.
To make sure total number of TX rings never exceed MAX_TX_RINGS,
add similar check in mlx4_en_alloc_tx_queue_per_tc(), where
a new value is assigned for num_up.
Fixes: 7e1dc5e926d5 ("net/mlx4_en: Limit the number of TX rings")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
info->options_len is 'u8' type, and when opts_len with a value >
IP_TUNNEL_OPTS_MAX, 'info->options_len = opts_len' will cast int
to u8 and set a wrong value to info->options_len.
Kernel crashed in my test when doing:
# opts="0102:80:00800022"
# for i in {1..99}; do opts="$opts,0102:80:00800022"; done
# ip link add name geneve0 type geneve dstport 0 external
# tc qdisc add dev eth0 ingress
# tc filter add dev eth0 protocol ip parent ffff: \
flower indev eth0 ip_proto udp action tunnel_key \
set src_ip 10.0.99.192 dst_ip 10.0.99.193 \
dst_port 6081 id 11 geneve_opts $opts \
action mirred egress redirect dev geneve0
So we should do the similar check as cls_flower does, return error
when opts_len > IP_TUNNEL_OPTS_MAX in tunnel_key_copy_opts().
Fixes: 0ed5269f9e41 ("net/sched: add tunnel option support to act_tunnel_key")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Simon Horman <simon.horman@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Michael Chan says:
====================
bnxt_en: Updates.
This series has the firmware interface update that changes the aRFS/ntuple
interface on 57500 chips. The 2nd patch adds a counter and improves
the hardware buffer error handling on the 57500 chips. The rest of the
series is mainly enhancements on error recovery and firmware reset.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is especially beneficial during the NVRAM related firmware
commands that have longer timeouts. If the BNXT_STATE_FW_FATAL_COND
flag gets set while waiting for firmware response, abort and return
error.
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During loss of heartbeat, log this warning message.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For NVM params that are not supported in the current NVM
configuration, return the error as -EOPNOTSUPP.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Report health status update to devlink health reporter, once
reset is completed.
Cc: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Linux driver is capable of being the master function to handle
resets, so we set the flag to let firmware know. Some other
drivers, such as DPDK, is not capable and will not set the flag.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If firmware supports hot reset, extend ETHTOOL_RESET to support
hot reset driver which does not require a driver reload after
ETHTOOL_RESET. The driver will go through the same coordinated
reset sequence as a firmware initiated fatal/non-fatal reset.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the larger HWRM_COREDUMP_TIMEOUT value for coredump related
data response from the firmware. These commands take longer than
normal commands.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When hardware reports RX buffer errors, the latest 57500 chips do not
require reset. The packet is discarded by the hardware and the
ring will continue to operate.
Also, add an rx_buf_errors counter for this type of error. It can help
the user to identify if the aggregation ring is too small.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The aRFS ring table interface has changed for the 57500 chips. Updating
it accordingly so it will work with the latest production firmware.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ido Schimmel says:
====================
selftests: Add ethtool and scale tests
This patch set adds generic ethtool tests and a mlxsw-specific router
scale test for Spectrum-2.
Patches #1-#2 from Danielle add the router scale test for Spectrum-2. It
re-uses the same test as Spectrum-1, but it is invoked with a different
scale, according to what it is queried from devlink-resource.
Patches #3-#5 from Amit are a re-work of the ethtool tests that were
posted in the past [1]. Patches #3-#4 add the necessary library
routines, whereas patch #5 adds the test itself. The test checks both
good and bad flows with autoneg on and off. The test plan it detailed in
the commit message.
Last time Andrew and Florian (copied) provided very useful feedback that
is incorporated in this set. Namely:
* Parse the value of the different link modes from
/usr/include/linux/ethtool.h
* Differentiate between supported and advertised speeds and use the
latter in autoneg tests
* Make the test generic and move it to net/forwarding/ instead of being
mlxsw-specific
[1] https://patchwork.ozlabs.org/cover/1112903/
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Check configurations and packets transference with different variations
of autoneg and speed.
Test plan:
1. Test force of same speed with autoneg off
2. Test force of different speeds with autoneg off (should fail)
3. One side is autoneg on and other side sets force of common speeds
4. One side is autoneg on and other side only advertises a subset of the
common speeds (one speed of the subset)
5. One side is autoneg on and other side only advertises a subset of the
common speeds. Check that highest speed is negotiated
6. Test autoneg on, but each side advertises different speeds (should
fail)
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a function that waits for device with maximum number of iterations.
It enables to limit the waiting and prevent infinite loop.
This will be used by the subsequent patch which will set two ports to
different speeds in order to make sure they cannot negotiate a link.
Waiting for all the setup is limited with 10 minutes for each device.
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Functions:
1. speeds_arr_get
The function returns an array of speed values from
/usr/include/linux/ethtool.h The array looks as follows:
[10baseT/Half] = 0,
[10baseT/Full] = 1,
...
2. ethtool_set:
params: cmd
The function runs ethtool by cmd (ethtool -s cmd) and checks if
there was an error in configuration
3. dev_speeds_get:
params: dev, with_mode (0 or 1), adver (0 or 1)
return value: Array of supported/Advertised link modes
with/without mode
* Example 1:
speeds_get swp1 0 0
return: 1000 10000 40000
* Example 2:
speeds_get swp1 1 1
return: 1000baseKX/Full 10000baseKR/Full 40000baseCR4/Full
4. common_speeds_get:
params: dev1, dev2, with_mode (0 or 1), adver (0 or 1)
return value: Array of common speeds of dev1 and dev2
* Example:
common_speeds_get swp1 swp2 0 0
return: 1000 10000
Assuming that swp1 supports 1000 10000 40000 and swp2 supports
1000 10000
Signed-off-by: Amit Cohen <amitc@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The scale test for Spectrum-2 should only be invoked for Spectrum-2.
Skip the test otherwise.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Same as for Spectrum-1, test the ability to add the maximum number of
routes possible to the switch.
Invoke the test from the 'resource_scale' wrapper script.
Signed-off-by: Danielle Ratson <danieller@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The helper mlxsw_sp_ipip_dev_ul_tb_id() determines the underlay VRF of a
GRE tunnel. For a tunnel without a bound device, it uses the same VRF that
the tunnel is in. However in Linux, a GRE tunnel without a bound device
uses the main VRF as the underlay. Fix the function accordingly.
mlxsw further assumed that moving a tunnel to a different VRF could cause
conflict in local tunnel endpoint address, which cannot be offloaded.
However, the only way that an underlay could be changed by moving the
tunnel device itself is if the tunnel device does not have a bound device.
But in that case the underlay is always the main VRF, so there is no
opportunity to introduce a conflict by moving such device. Thus this check
constitutes a dead code, and can be removed, which do.
Fixes: 6ddb7426a7d4 ("mlxsw: spectrum_router: Introduce loopback RIFs")
Signed-off-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case of errors in unlink_clip_vcc, the logging level is set to
pr_crit but failures in clip_setentry are handled by pr_err().
The patch changes the severity consistent across invocations.
Signed-off-by: Aditya Pakki <pakki001@umn.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
