| Age | Commit message (Collapse) | Author |
|---|
|
When a hardware reset is triggered, all registers are reset, so all
queues are forced to stop in hardware interface. However, mac80211
will not automatically stop the queue. If we don't manually stop the
beacon queue, the queue will be deadlocked and unable to start again.
This patch fixes the issue where Apple devices cannot connect to the
AP after calling ieee80211_restart_hw().
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/TYAP286MB031530EB6D98DCE4DF20766CBCA4A@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM
|
|
rt2800 has a lot of registers to control the RTS enable/disable
status for different rates. And the driver control them via
rt2800_set_rts_threshold(). When RTS was disabled in user
interface, this function won't be called at all. This means that
the RTS is still 'on' for CCK and OFDM rates. So we'd better to
disable them by default because it should be like this. The RTS
for HT20 and HT40 is already default off so we don't need to
touch them. If we toggle the RTS status, these register bits
will be enable/disable again by rt2800_set_rts_threshold().
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/TYAP286MB03155DDB953155B7A2DE849ABCA4A@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM
|
|
When I tried to fix the watchdog of rt2800, I found that sometimes
the watchdog can not reset the hung device. This is because the
queue is not completely stuck, it just becomes very slow. The MTK
vendor driver for the new chip MT7603/MT7612 has a DMA busy watchdog
to detect device hangs by checking DMA busy status. This watchdog
implementation is something similar to it. To reduce unnecessary
reset, we can check the INT_SOURCE_CSR register together as I found
that when the radio hung, the RX/TX coherent interrupt will always
stuck at triggered state.
The 'watchdog' module parameter has been extended to control all
watchdogs(0=disabled, 1=hang watchdog, 2=DMA watchdog, 3=both). This
new watchdog function is a slight schedule and it won't affect the
transmission speed. So we can turn on it by default. Due to the
INT_SOURCE_CSR register is invalid on rt2800 USB NICs, the DMA busy
watchdog will be automatically disabled for them.
Tested on MT7620 and RT5350.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Acked-by: Stanislaw Gruszka <stf_xl@wp.pl>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/TYAP286MB0315D7462CE08A119A99DE34BCA4A@TYAP286MB0315.JPNP286.PROD.OUTLOOK.COM
|
|
The broadcast packets will be filtered in the FIF_ALLMULTI flag in
the original code, which causes beacon packets to be filtered out
and disconnection. Therefore, we fix it.
Fixes: e3037485c68e ("rtw88: new Realtek 802.11ac driver")
Signed-off-by: Chih-Kang Chang <gary.chang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231103020851.102238-1-pkshih@realtek.com
|
|
Since 'ieee80211_txq_get_depth()' allows NULL for 2nd and
3rd arguments, simplify '__rtw_tx_work()' by dropping unused
'byte_cnt'. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231102115606.69838-1-dmantipov@yandex.ru
|
|
content
To notify firmware TDMA timeslot assignment, append TDMA parameters when
sending policy H2C firmware command. However, compiler warns we do memcpy()
data to val[] field of TLV struct. To avoid this, assign the struct value
with simple '=' instead. Compile tested only.
rtw89/coex.c: In function '_append_tdma':
drivers/net/wireless/realtek/rtw89/coex.c:1585:17:
warning: writing 8 bytes into a region of size 0 [-Wstringop-overflow=]
1585 | memcpy(&v3->tdma, &dm->tdma, sizeof(v3->tdma));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
In file included from drivers/net/wireless/realtek/rtw89/coex.h:8,
from drivers/net/wireless/realtek/rtw89/coex.c:5:
drivers/net/wireless/realtek/rtw89/core.h:2703:37:
note: at offset [5714, 71249] into destination object 'ver' of size 8
2703 | const struct rtw89_btc_ver *ver;
| ^~~
drivers/net/wireless/realtek/rtw89/coex.c:1579:17:
warning: writing 8 bytes into a region of size 0 [-Wstringop-overflow=]
1579 | memcpy(v, &dm->tdma, sizeof(*v));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/realtek/rtw89/core.h:2703:37:
note: at offset [5710, 71245] into destination object 'ver' of size 8
2703 | const struct rtw89_btc_ver *ver;
| ^~~
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202310301908.Wrj0diqe-lkp@intel.com/
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231102003716.25815-1-pkshih@realtek.com
|
|
For normal use, we do additional settings than mac_pre_init, such as
more TX/RX DMA channels, interrupt mitigation and etc.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231101072149.21997-6-pkshih@realtek.com
|
|
PCI LTR (Latency Tolerance Reporting) is a capability to yield expected
power consumption, and we configure the parameters according to design.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231101072149.21997-5-pkshih@realtek.com
|
|
Call this function when doing MAC initialization at probe stage. It does
partial initial registers only, because we only need basic ability to
download firmware. The function to clear index is the sub-function,
so set its pointer as well.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231101072149.21997-4-pkshih@realtek.com
|
|
clear PCI ring index
Use gen_def pointer to call three WiFi 6 specific functions, and add _ax
suffix to them. Then, we will implement functions for WiFi 7 chips later.
The mac_{pre,post}_init are used to initialize PCI during doing MAC
initialization, and clear PCI ring index to make index consistent between
driver, firmware and hardware.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231101072149.21997-3-pkshih@realtek.com
|
|
In order to reuse PCI initial and configuration flows, add struct
rtw89_pci_gen_def to abstract the differences between WiFi 6/7 generations.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231101072149.21997-2-pkshih@realtek.com
|
|
Simplify 'wilc_scan()' assuming 'struct wilc_priv *' is the only data
passed to '(*scan_result)()' callback and thus avoid typeless 'void *'
pointers in related code, including 'struct wilc_user_scan_req'.
Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231031171330.70399-2-dmantipov@yandex.ru
|
|
Remove set but otherwise unused 'ch' member of 'struct wilc_conn_info'
and avoid typeless 'void *' pointers in '(*conn_result)()' callback.
Likewise for 'wilc_parse_join_bss_param()'. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231031171330.70399-1-dmantipov@yandex.ru
|
|
Check for if the usb_alloc_urb() failed.
Fixes: 68d57a07bfe5 ("wireless: add plfxlc driver for pureLiFi X, XL, XC devices")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/e8d4a19a-f251-4101-a89b-607345e938cb@moroto.mountain
|
|
Wireless RNDIS USB is a new-style CFG80211 driver for 802.11b and
802.11g USB hardware from around 2004 to 2006. This makes it more modern
than any of the others, but Kalle already classified it as "legacy"
in commit 298e50ad8eb8f ("wifi: move raycs, wl3501 and rndis_wlan to
legacy directory").
Jussi Kivilinna worked on this driver between 2008 and 2012, and it has
only seen cosmetic updates after that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
|
|
Planet WL3501 is another PCMCIA driver for pre-802.11b interfaces
(2Mbit/s) with incomplete CFG80211 support.
This was marked as orphaned in 2017 but has been unmaintained
for a long time before that.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
|
|
Aviator/Raytheon is an early PCMCIA driver, apparently predating 802.11b
and only supporting wireless extensions.
The driver has been orphaned since 2010 and only seen cosmetic updates
long before than. Jean Tourrilhes pointed out in a 2005 changelog that
he tested a change on actual hardware, which was apparently already
noteworthy back then.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
|
|
Orinoco is a PIO-only ISA/PCMCIA 802.11b device with extra bus interface
connections for PCI/Cardbus/mini-PCI and a few pre-2002 Apple PowerMac
variants. It supports both wireless extensions and CFG80211, but I could
not tell if it requires using both.
This device used to be one of the most common ones 20 years ago, but
has been orphaned for most of the time since then, and the conversion
to cfg80211 has stalled in 2010.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
|
|
This is a wireless extensions style driver for 802.11b USB dongles,
with partial support for cfg80211 interfaces.
As these are all external dongles, there are probably few users that
have not yet replaced them with cheap 802.11n devices that work better.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
|
|
HostAP is an ISA/PCMCIA style 802.11b driver supporting only
wireless extensions, and some custom ioctls (already removed).
Some devices include a legacy PCI bridge but no DMA.
The driver was marked obsolete in 2016 and is highly unlikely
to still have any users.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
|
|
Cisco Aironet is an 802.11b PCMCIA and mini-PCI with limited support
for Cardbus DMA and for CFG80211.
Both PCMCIA and WEXT are deprecated, and there is little chance
that anyone is still using this driver, so remove it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
|
|
Atmel at76c502/at76c504/at76c506 is a PIO-only (PCMCIA, mini-PCI
and Cardbus) 802.11b driver with incomplete CFG80211 support.
Both PCMCIA and WEXT are deprecated, and there is little chance
that anyone is still using this driver, so remove it.
The related at76c50x USB driver uses MAC80211 and remains.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
|
|
With all the other PCMCIA WLAN adapters gone from the kernel, this is now
the last remaining device with this interface, but as far as I can tell,
all the actual libertas users were actually using either SDIO or USB.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
|
|
PHY status IEs is used to have more information about received packets,
such as RSSI and EVM. For each PHY IE type, it has different predefined
PHY IE length, and the length are changed, so add them for WiFi 7 chips
accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231027015059.10032-5-pkshih@realtek.com
|
|
For WiFi 7 chips, some fields and predefined length are changed, so
add them accordingly.
The mac_id field is used to identify peer that send a packet, and we can
use it to know RSSI and traffic from the peer. For WiFi 7 chips,
RXWD.mac_id of PPDU status packet is not set by hardware. Instead, we
should fill it by rxinfo_user[].mac_id of PPDU status content.
Also, filter out invalid reports to prevent warning messages keep showing.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231027015059.10032-4-pkshih@realtek.com
|
|
Different chip can support different max user in one PPDU report.
So, we now configure it in chip info.
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231027015059.10032-3-pkshih@realtek.com
|
|
The new chips change hardware design to shrink entry size of address
CAM from 0x40 to 0x20, so make this change accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231027015059.10032-2-pkshih@realtek.com
|
|
strncpy() is deprecated for use on NUL-terminated destination strings
[1] and as such we should prefer more robust and less ambiguous string
interfaces.
`extra` is clearly supposed to be NUL-terminated which is evident by the
manual NUL-byte assignment as well as its immediate usage with strlen().
Moreover, let's NUL-pad since there is deliberate effort (48 instances)
made elsewhere to zero-out buffers in these getters and setters:
6050 | memset(local->config.nodeName, 0, sizeof(local->config.nodeName));
6130 | memset(local->config.rates, 0, 8);
6139 | memset(local->config.rates, 0, 8);
6414 | memset(key.key, 0, MAX_KEY_SIZE);
6497 | memset(extra, 0, 16);
(to be clear, strncpy also NUL-padded -- we are matching that behavior)
Considering the above, a suitable replacement is `strscpy_pad` due to
the fact that it guarantees both NUL-termination and NUL-padding on the
destination buffer.
We can also replace the hard-coded size of "16" to IW_ESSID_MAX_SIZE
because this function is a wext handler.
In wext-core.c we have:
static const struct iw_ioctl_description standard_ioctl[] = {
...
[IW_IOCTL_IDX(SIOCGIWNICKN)] = {
.header_type = IW_HEADER_TYPE_POINT,
.token_size = 1,
.max_tokens = IW_ESSID_MAX_SIZE,
},
So the buffer size is (strangely) IW_ESSID_MAX_SIZE
Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings [1]
Link: https://github.com/KSPP/linux/issues/90
Cc: linux-hardening@vger.kernel.org
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Jeff Johnson <quic_jjohnson@quicinc.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231026-strncpy-drivers-net-wireless-cisco-airo-c-v2-1-413427249e47@google.com
|
|
Ensure 'sdio_release_host()' is always issued on return
from 'wilc_sdio_cmd53()'. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231026141016.71407-2-dmantipov@yandex.ru
|
|
For 'struct wilc_remain_ch', drop set but otherwise unused 'duration'
field and adjust 'expired' callback assuming that the only data passed
to it is 'struct wilc_vif *', thus making 'wilc_remain_on_channel()'
a bit simpler as well. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231026141016.71407-1-dmantipov@yandex.ru
|
|
The register to enable/disable PCI DMA IO has many variants, so define
and use a field to control it accordingly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231026120049.9187-5-pkshih@realtek.com
|
|
To make hardware efficient to determine if RX ring is full, introduce new
design that checks if reading and writing indices are equal. Comparing
to old design, initial indices of both reading and writing indices are 0
that means empty, and hardware checks full by "writing index + 1 ==
reading index". The "+1" has extra cost for hardware, so new design is
to avoid this.
Take ring size is 256 as an example, the initial reading and writing
indices are 255 and 0 respectively; the initial values mean empty. If two
indices are the same, for example 5 and 5, it means ring is full.
wp rp used_cnt state
255 0 0 initial (ring is empty)
255 1 1 receive 1st packet
255 2 2 receive 2nd packet
0 2 1 driver read 1st packet
1 2 0 driver read 2nd packet (ring is empty)
:
5 5 255 ring is full
Note: 'rp' is hardware writing index
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231026120049.9187-4-pkshih@realtek.com
|
|
PCI rings are used to DMA TX/RX packets. The address of WiFi 7 chips are
different from previous ones, so add them according to hardware design.
Another difference is that driver doesn't need to configure BD (buffer
descriptor) RAM table, which is used by hardware to fetch BD ahead before
fetching whole TX data.
A TX ring contains numbers of TX BD (e.g. 512):
TX BD (buffer descriptor; continual memory)
+---+---+---+---+ +---+
| | | | | ... | |
+-|-+---+---+---+ +---+
|
| point to TX WD (WiFi descriptor; metadata of a skb data)
v
+------+
| |
| |
+-|----+
|
| point to a skb data
v
+------+
| |
| |
+------+
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231026120049.9187-3-pkshih@realtek.com
|
|
8922AE is a PCIE 802.11be wireless adapter with PID 0x8922. We add basic
configurations including PCI DMA mode, PCI parameters, register address to
control TX/RX rings and etc.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231026120049.9187-2-pkshih@realtek.com
|
|
Since 'rtw89_core_tx_kick_off_and_wait()' assumes timeout
(actually RTW89_ROC_TX_TIMEOUT) in milliseconds, I suppose
that RTW89_ROC_IDLE_TIMEOUT is in milliseconds as well. If
so, 'msecs_to_jiffies()' should be used in a call to
'ieee80211_queue_delayed_work()' from 'rtw89_roc_end()'.
Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231024143137.30393-1-dmantipov@yandex.ru
|
|
For rtl8192ee, change 'rtl92ee_dm_dynamic_primary_cca_ckeck()'
to 'rtl92ee_dm_dynamic_primary_cca_check()' and so adjust
'rtl92ee_dm_watchdog()' as well. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231023091722.52509-3-dmantipov@yandex.ru
|
|
Remove unused and read by otherwise unused 'h2c_box_num',
'rfpienable', 'reserve_0', 'reserve_1', 'iqk_in_progress',
'apk_done' and 'hw_rof_enable' fields of 'struct rtl_phy',
adjust related code. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231023091722.52509-2-dmantipov@yandex.ru
|
|
Remove unused and set but otherwise unused 'bbrf_ready', 'external_pa',
'pa_mode', 'rx_tag', 'rts_en', 'wow_enable' and 'wow_enabled' fields
of 'struct rtl_hal', adjust related code. Compile tested only.
Signed-off-by: Dmitry Antipov <dmantipov@yandex.ru>
Acked-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231023091722.52509-1-dmantipov@yandex.ru
|
|
Let's move away from using strncpy and instead use the more obvious
interface for this context.
For wlc->pub->srom_ccode, we're just copying two bytes from ccode into
wlc->pub->srom_ccode with no expectation that srom_ccode be
NUL-terminated:
wlc->pub->srom_ccode is only used in regulatory_hint():
1193 | if (wl->pub->srom_ccode[0] &&
1194 | regulatory_hint(wl->wiphy, wl->pub->srom_ccode))
1195 | wiphy_err(wl->wiphy, "%s: regulatory hint failed\n", __func__);
We can see that only index 0 and index 1 are accessed.
3307 | int regulatory_hint(struct wiphy *wiphy, const char *alpha2)
3308 | {
... | ...
3322 | request->alpha2[0] = alpha2[0];
3323 | request->alpha2[1] = alpha2[1];
... | ...
3332 | }
Since this is just a simple byte copy with correct lengths, let's use
memcpy(). There should be no functional change.
In a similar boat, both wlc->country_default and
wlc->autocountry_default are just simple byte copies so let's use
memcpy. However, FWICT they aren't used anywhere. (they should be
used or removed -- not in scope of my patch, though).
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231017-strncpy-drivers-net-wireless-broadcom-brcm80211-brcmfmac-cfg80211-c-v3-2-af780d74ae38@google.com
|
|
Let's move away from using strncpy and instead favor a less ambiguous
and more robust interface.
For ifp->ndev->name, we expect ifp->ndev->name to be NUL-terminated based
on its use in format strings within core.c:
67 | char *brcmf_ifname(struct brcmf_if *ifp)
68 | {
69 | if (!ifp)
70 | return "<if_null>";
71 |
72 | if (ifp->ndev)
73 | return ifp->ndev->name;
74 |
75 | return "<if_none>";
76 | }
...
288 | static netdev_tx_t brcmf_netdev_start_xmit(struct sk_buff *skb,
289 | struct net_device *ndev) {
...
330 | brcmf_dbg(INFO, "%s: insufficient headroom (%d)\n",
331 | brcmf_ifname(ifp), head_delta);
...
336 | bphy_err(drvr, "%s: failed to expand headroom\n",
337 | brcmf_ifname(ifp));
For di->name, we expect di->name to be NUL-terminated based on its usage
with format strings:
| brcms_dbg_dma(di->core,
| "%s: DMA64 tx doesn't have AE set\n",
| di->name);
Looking at its allocation we can see that it is already zero-allocated
which means NUL-padding is not required:
| di = kzalloc(sizeof(struct dma_info), GFP_ATOMIC);
For wlc->modulecb[i].name, we expect each name in wlc->modulecb to be
NUL-terminated based on their usage with strcmp():
| if (!strcmp(wlc->modulecb[i].name, name) &&
NUL-padding is not required as wlc is zero-allocated in:
brcms_c_attach_malloc() ->
| wlc = kzalloc(sizeof(struct brcms_c_info), GFP_ATOMIC);
For all these cases, a suitable replacement is `strscpy` due to the fact
that it guarantees NUL-termination on the destination buffer without
unnecessarily NUL-padding.
Signed-off-by: Justin Stitt <justinstitt@google.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@kernel.org>
Link: https://lore.kernel.org/r/20231017-strncpy-drivers-net-wireless-broadcom-brcm80211-brcmfmac-cfg80211-c-v3-1-af780d74ae38@google.com
|
|
Messages submitted to the ML bounce (address not found error). In
fact, the ML was mistagged as person maintainer instead of mailing
list.
Remove the ML to keep Cc: lists a bit shorter and not to spam
everyone's inbox with postmaster notifications.
Signed-off-by: Bagas Sanjaya <bagasdotme@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20231025130332.67995-2-bagasdotme@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Jacob Keller says:
====================
Intel Wired LAN Driver Updates for 2023-10-25 (ice)
This series extends the ice driver with basic support for the E830 device
line. It does not include support for all device features, but enables basic
functionality to load and pass traffic.
Alice adds the 200G speed and PHY types supported by E830 hardware.
Dan extends the DDP package logic to support the E830 package segment.
Paul adds the basic registers and macros used by E830 hardware, and adds
support for handling variable length link status information from firmware.
Pawel removes some redundant zeroing of the PCI IDs list, and extends the
list to include the E830 device IDs.
====================
Link: https://lore.kernel.org/r/20231025214157.1222758-1-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As the previous patches provide support for E830 hardware, add E830
specific IDs to the PCI device ID table, so these devices can now be
probed by the kernel.
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231025214157.1222758-7-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove zeroing of the fields, as all the fields are in fact initialized
with zeros automatically
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231025214157.1222758-6-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for E830 DDP package segment. For the E830 package,
signature buffers will not be included inline in the configuration
buffers. Instead, the signature buffers will be located in a
signature segment.
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Co-developed-by: Paul Greenwalt <paul.greenwalt@intel.com>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231025214157.1222758-5-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The Get Link Status data length can vary with different versions of
ice_aqc_get_link_status_data. Add ice_get_link_status_datalen() to return
datalen for the specific ice_aqc_get_link_status_data version.
Add new link partner fields to ice_aqc_get_link_status_data; PHY type,
FEC, and flow control.
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Co-developed-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Signed-off-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231025214157.1222758-4-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add the support for 200G phy speeds and the mapping for their
advertisement in link. Add the new PHY type bits for AQ command, as
needed for 200G E830 controllers.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Co-developed-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Signed-off-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231025214157.1222758-3-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
E830 is the 200G NIC family which uses the ice driver.
Add specific E830 registers. Embed macros to use proper register based on
(hw)->mac_type & name those macros to [ORIGINAL]_BY_MAC(hw). Registers
only available on one of the macs will need to be explicitly referred to
as E800_NAME instead of just NAME. PTP is not yet supported.
Co-developed-by: Milena Olech <milena.olech@intel.com>
Signed-off-by: Milena Olech <milena.olech@intel.com>
Co-developed-by: Dan Nowlin <dan.nowlin@intel.com>
Signed-off-by: Dan Nowlin <dan.nowlin@intel.com>
Co-developed-by: Scott Taylor <scott.w.taylor@intel.com>
Signed-off-by: Scott Taylor <scott.w.taylor@intel.com>
Co-developed-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Signed-off-by: Pawel Chmielewski <pawel.chmielewski@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Paul Greenwalt <paul.greenwalt@intel.com>
Tested-by: Tony Brelinski <tony.brelinski@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20231025214157.1222758-2-jacob.e.keller@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next
Kalle Valo says:
====================
wireless-next patches for v6.7
The third, and most likely the last, features pull request for v6.7.
Fixes all over and only few small new features.
Major changes:
iwlwifi
- more Multi-Link Operation (MLO) work
ath12k
- QCN9274: mesh support
ath11k
- firmware-2.bin container file format support
* tag 'wireless-next-2023-10-26' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (155 commits)
wifi: ray_cs: Remove unnecessary (void*) conversions
Revert "wifi: ath11k: call ath11k_mac_fils_discovery() without condition"
wifi: ath12k: Introduce and use ath12k_sta_to_arsta()
wifi: ath12k: fix htt mlo-offset event locking
wifi: ath12k: fix dfs-radar and temperature event locking
wifi: ath11k: fix gtk offload status event locking
wifi: ath11k: fix htt pktlog locking
wifi: ath11k: fix dfs radar event locking
wifi: ath11k: fix temperature event locking
wifi: ath12k: rename the sc naming convention to ab
wifi: ath12k: rename the wmi_sc naming convention to wmi_ab
wifi: ath11k: add firmware-2.bin support
wifi: ath11k: qmi: refactor ath11k_qmi_m3_load()
wifi: rtw89: cleanup firmware elements parsing
wifi: rt2x00: rework MT7620 PA/LNA RF calibration
wifi: rt2x00: rework MT7620 channel config function
wifi: rt2x00: improve MT7620 register initialization
MAINTAINERS: wifi: rt2x00: drop Helmut Schaa
wifi: wlcore: main: replace deprecated strncpy with strscpy
wifi: wlcore: boot: replace deprecated strncpy with strscpy
...
====================
Link: https://lore.kernel.org/r/20231026090411.B2426C433CB@smtp.kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next
Daniel Borkmann says:
====================
pull-request: bpf-next 2023-10-26
We've added 51 non-merge commits during the last 10 day(s) which contain
a total of 75 files changed, 5037 insertions(+), 200 deletions(-).
The main changes are:
1) Add open-coded task, css_task and css iterator support.
One of the use cases is customizable OOM victim selection via BPF,
from Chuyi Zhou.
2) Fix BPF verifier's iterator convergence logic to use exact states
comparison for convergence checks, from Eduard Zingerman,
Andrii Nakryiko and Alexei Starovoitov.
3) Add BPF programmable net device where bpf_mprog defines the logic
of its xmit routine. It can operate in L3 and L2 mode,
from Daniel Borkmann and Nikolay Aleksandrov.
4) Batch of fixes for BPF per-CPU kptr and re-enable unit_size checking
for global per-CPU allocator, from Hou Tao.
5) Fix libbpf which eagerly assumed that SHT_GNU_verdef ELF section
was going to be present whenever a binary has SHT_GNU_versym section,
from Andrii Nakryiko.
6) Fix BPF ringbuf correctness to fold smp_mb__before_atomic() into
atomic_set_release(), from Paul E. McKenney.
7) Add a warning if NAPI callback missed xdp_do_flush() under
CONFIG_DEBUG_NET which helps checking if drivers were missing
the former, from Sebastian Andrzej Siewior.
8) Fix missed RCU read-lock in bpf_task_under_cgroup() which was throwing
a warning under sleepable programs, from Yafang Shao.
9) Avoid unnecessary -EBUSY from htab_lock_bucket by disabling IRQ before
checking map_locked, from Song Liu.
10) Make BPF CI linked_list failure test more robust,
from Kumar Kartikeya Dwivedi.
11) Enable samples/bpf to be built as PIE in Fedora, from Viktor Malik.
12) Fix xsk starving when multiple xsk sockets were associated with
a single xsk_buff_pool, from Albert Huang.
13) Clarify the signed modulo implementation for the BPF ISA standardization
document that it uses truncated division, from Dave Thaler.
14) Improve BPF verifier's JEQ/JNE branch taken logic to also consider
signed bounds knowledge, from Andrii Nakryiko.
15) Add an option to XDP selftests to use multi-buffer AF_XDP
xdp_hw_metadata and mark used XDP programs as capable to use frags,
from Larysa Zaremba.
16) Fix bpftool's BTF dumper wrt printing a pointer value and another
one to fix struct_ops dump in an array, from Manu Bretelle.
* tag 'for-netdev' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (51 commits)
netkit: Remove explicit active/peer ptr initialization
selftests/bpf: Fix selftests broken by mitigations=off
samples/bpf: Allow building with custom bpftool
samples/bpf: Fix passing LDFLAGS to libbpf
samples/bpf: Allow building with custom CFLAGS/LDFLAGS
bpf: Add more WARN_ON_ONCE checks for mismatched alloc and free
selftests/bpf: Add selftests for netkit
selftests/bpf: Add netlink helper library
bpftool: Extend net dump with netkit progs
bpftool: Implement link show support for netkit
libbpf: Add link-based API for netkit
tools: Sync if_link uapi header
netkit, bpf: Add bpf programmable net device
bpf: Improve JEQ/JNE branch taken logic
bpf: Fold smp_mb__before_atomic() into atomic_set_release()
bpf: Fix unnecessary -EBUSY from htab_lock_bucket
xsk: Avoid starving the xsk further down the list
bpf: print full verifier states on infinite loop detection
selftests/bpf: test if state loops are detected in a tricky case
bpf: correct loop detection for iterators convergence
...
====================
Link: https://lore.kernel.org/r/20231026150509.2824-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
