| Age | Commit message (Collapse) | Author |
|---|
|
This patch introduces a new module parameter for the KVM module; when it
is present, KVM attempts a bit of polling on every HLT before scheduling
itself out via kvm_vcpu_block.
This parameter helps a lot for latency-bound workloads---in particular
I tested it with O_DSYNC writes with a battery-backed disk in the host.
In this case, writes are fast (because the data doesn't have to go all
the way to the platters) but they cannot be merged by either the host or
the guest. KVM's performance here is usually around 30% of bare metal,
or 50% if you use cache=directsync or cache=writethrough (these
parameters avoid that the guest sends pointless flush requests, and
at the same time they are not slow because of the battery-backed cache).
The bad performance happens because on every halt the host CPU decides
to halt itself too. When the interrupt comes, the vCPU thread is then
migrated to a new physical CPU, and in general the latency is horrible
because the vCPU thread has to be scheduled back in.
With this patch performance reaches 60-65% of bare metal and, more
important, 99% of what you get if you use idle=poll in the guest. This
means that the tunable gets rid of this particular bottleneck, and more
work can be done to improve performance in the kernel or QEMU.
Of course there is some price to pay; every time an otherwise idle vCPUs
is interrupted by an interrupt, it will poll unnecessarily and thus
impose a little load on the host. The above results were obtained with
a mostly random value of the parameter (500000), and the load was around
1.5-2.5% CPU usage on one of the host's core for each idle guest vCPU.
The patch also adds a new stat, /sys/kernel/debug/kvm/halt_successful_poll,
that can be used to tune the parameter. It counts how many HLT
instructions received an interrupt during the polling period; each
successful poll avoids that Linux schedules the VCPU thread out and back
in, and may also avoid a likely trip to C1 and back for the physical CPU.
While the VM is idle, a Linux 4 VCPU VM halts around 10 times per second.
Of these halts, almost all are failed polls. During the benchmark,
instead, basically all halts end within the polling period, except a more
or less constant stream of 50 per second coming from vCPUs that are not
running the benchmark. The wasted time is thus very low. Things may
be slightly different for Windows VMs, which have a ~10 ms timer tick.
The effect is also visible on Marcelo's recently-introduced latency
test for the TSC deadline timer. Though of course a non-RT kernel has
awful latency bounds, the latency of the timer is around 8000-10000 clock
cycles compared to 20000-120000 without setting halt_poll_ns. For the TSC
deadline timer, thus, the effect is both a smaller average latency and
a smaller variance.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Use the new helper function to create sysfs entries in the card more
gracefully without races.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/drivers
Merge "Samsung CPUIdle updates for v3.20" from Kukjin Kim:
- adds coupled cpuidle support for exynos4210
: fix for Exynos platform PM code preparing it for the coupled
cpuidle support and adds coupled cpuidle AFTR mode on exynos4210
Note this is mostrly based on earlier cpuidle-exynos4210 driver
from Daniel Lezcano and Bart updated.
* tag 'samsung-cpuidle' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
cpuidle: exynos: add coupled cpuidle support for exynos4210
ARM: EXYNOS: apply S5P_CENTRAL_SEQ_OPTION fix only when necessary
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/dt
Merge "Samsung 4th DT updates for v3.20" from Kukjin Kim:
- For exynos4 SoCs
: add PPMU node
: add syscon phandle for video-phy node
- For exynos4415 SoC
: add mipi dsi and fimd device nodes
- For exynos3250-monk and exynos3250-rinato boards
: add PPMU node
- For exynos4412-trats2 board
: add maxim77693 fuel gauge and battery charger nodes
: fix regarding CLK_MOUT_CAMn parent and CLK_UART_ISP_SCLK clocks
: switch max77686 regulators to GPIO control
: add suspend configuration for max77686 regulators
: add PPMU node and sound nodes
* tag 'samsung-dt-4' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: dts: Add PPMU node for exynos4412-trats2
ARM: dts: Add PPMU node for exynos3250-monk and exynos3250-rinato
ARM: dts: Add PPMU dt node for exynos4 and exynos4210
ARM: dts: Add PPMU dt node for exynos3250
ARM: dts: add mipi dsi device node for exynos4415
ARM: dts: add fimd device node for exynos4415
ARM: dts: Add syscon phandle to the video-phy node for Exynos4
ARM: dts: Add sound nodes for exynos4412-trats2
ARM: dts: Fix CLK_MOUT_CAMn parent clocks assignment for exynos4412-trats2
ARM: dts: Fix CLK_UART_ISP_SCLK clock assignment in exynos4x12.dtsi
ARM: dts: Add max77693 charger node for exynos4412-trats2
ARM: dts: Switch max77686 regulators to GPIO control for exynos4412-trats2
ARM: dts: Add suspend configuration for max77686 regulators for exynos4412-trats2
ARM: dts: Add Maxim 77693 fuel gauge node for exynos4412-trats2
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
For assigning sysfs entries for a card device from the driver,
introduce a new helper function, snd_card_add_dev_attr(). In this
way, we can avoid the possible race between the device registration
and the sysfs addition / removal.
The driver can pass a new attribute group to add freely. This has to
be called before snd_card_register().
Currently, up to two extra groups can be added. More than that, it'll
return an error.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
While commit 7e36ef8205ff ("IB/core: Temporarily disable
ex_query_device uverb") is correct as it makes the extended
QUERY_DEVICE uverb (which came as part of commit 5a77abf9a97a
("IB/core: Add support for extended query device caps") and commit
860f10a799c8 ("IB/core: Add flags for on demand paging support")) not
available to userspace, it doesn't address the initial issue regarding
ib_copy_to_udata() [1][2].
Additionally, further discussions around this new uverb seems to
conclude it would require a different data structure than the one
currently described in <rdma/ib_user_verbs.h> [3].
Both of these issues require a revert of the changes, so this patch
partially reverts commit 8cdd312cfed7 ("IB/mlx5: Implement the ODP
capability query verb") and commit 860f10a799c8 ("IB/core: Add flags
for on demand paging support") and fully reverts commit 5a77abf9a97a
("IB/core: Add support for extended query device caps").
[1] "Re: [PATCH v3 06/17] IB/core: Add support for extended query device caps"
http://mid.gmane.org/1418733236.2779.26.camel@opteya.com
[2] "Re: [PATCH] IB/core: Temporarily disable ex_query_device uverb"
http://mid.gmane.org/1423067503.3030.83.camel@opteya.com
[3] "RE: [PATCH v1 1/5] IB/uverbs: ex_query_device: answer must not depend on request's comp_mask"
http://mid.gmane.org/2807E5FD2F6FDA4886F6618EAC48510E0CC12C30@CRSMSX101.amr.corp.intel.com
Cc: Eli Cohen <eli@mellanox.com>
Cc: Haggai Eran <haggaie@mellanox.com>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Cc: Sagi Grimberg <sagig@mellanox.com>
Cc: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Yann Droneaud <ydroneaud@opteya.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung into next/defconfig
Merge "Samsung exynos_defconfig updates for v3.20" from Kukjin Kim:
- Enable CONFIG_LOCKUP_DETECTOR
: to detect hard lockup and soft lockup
- Enable PMIC and MUIC
: for battery charger, fuel-gauge, regulators
- Enable CONFIG_FHANDLE
: this is required by systemd
* tag 'samsung-defconfig' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung:
ARM: exynos_defconfig: Enable CONFIG_FHANDLE
ARM: exynos_defconfig: Enable PMIC and MUIC drivers for Gears and Trats2
ARM: exynos_defconfig: Enable CONFIG_LOCKUP_DETECTOR
ARM: exynos_defconfig: Enable LM90 driver
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Merge "ARM: mvebu: DT changes for v3.20 (round 2)" from Gregory CLEMENT:
Relicense all Armada dts{i} files under dual license of GPLv2+ and
X11. This should make it easier to reuse these files with other
operating systems and boot loaders.
* tag 'mvebu-dt-3.20-3' of git://git.infradead.org/linux-mvebu: (27 commits)
ARM: mvebu: armada-xp-synology-ds414: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-openblocks-ax3-4: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-netgear-rn2120: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-mv78460: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-mv78260: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-mv78230: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-matrix: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-lenovo-ix4-300d: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-gp: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-db: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-xp-axpwifiap: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-38x: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-388-rd: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-385: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-388-db: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-380: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-375: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-375-db: Relicense the device tree under GPLv2+/X11
ARM: mvebu: armada-370-xp: Relicense the device tree under GPLv2+/X11
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
with the patchset to add CSR atlas7 support, the below stuff
has no user now:
SIRFSOC_VA
sirfsoc_map_lluart
sirfsoc_map_scu
the related patches missed to drop them.
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/defconfig
Merge "ARM: Keystone soc config updates for 3.20" from Santosh Shilimkar:
Keystone DEVTMPFS config update for 3.20
* tag 'keystone-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
ARM: config: add DEVTMPFS option by default to keystone config
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/drivers
Merge "soc: ti: Keystone Navigator SOC driver updates for 3.20" from Santosh
Shilimkar:
Keystone Navigator SOC driver updates for 3.20
- Makefile tweak so that knav_qmss and knav_dma can be made loadable
modules without depedency issues.
- Few more exports to support ARM allmodconfig.
- Marking knav_range_setup_acc_irq() local function as static.
* tag 'drivers-soc-ti' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
soc: ti: knav_qmss_queue: change knav_range_setup_acc_irq to static
soc: ti: knav_qmss_queue: makefile tweak to build as dynamic module
soc: ti: knav_qmss_queue: export API calls for use by user driver
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Now that we can specify which PMU variant we're likely to deal with, do
so in the omap board code. This will allow us to split the ARMv6, ARMv7,
and XScale PMU drivers.
The unnecessary include of asm/pmu.h is also removed.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Now that we can specify which PMU variant we're likely to deal with, do
so in the shmobile board code. This will allow us to split the ARMv6,
ARMv7, and XScale PMU drivers
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Now that we can specify which PMU variant we're likely to deal with, do
so in the iop board code. This will allow us to split the ARMv6, ARMv7,
and XScale PMU drivers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Now that we can specify which PMU variant we're likely to deal with, do
so in the pxa board code. This will allow us to split the ARMv6, ARMv7,
and XScale PMU drivers.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Daniel Mack <daniel@zonque.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Cc: Olof Johansson <olof@lixom.net>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Now that we can specify which PMU variant we're likely to deal with, do
so in the realview board code. This will allow us to split the ARMv6,
ARMv7, and XScale PMU drivers.
The Realview EB may be used with ARMv6 or ARMv7 CPUs, but luckily
there's only a single ARMv7 CPU, so we can match that explicitly to
determine whether or not we have an ARMv7 PMU.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Olof Johansson <olof@lixom.net>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Merge "omap device tree changes for v3.20, part 3" from Tony Lindgren:
Device tree related chages for omaps to fix dm816x syscon,
fix various devices for gta04, and add USB nodes for am57xx
and dra7.
* tag 'omap-for-v3.20/dt-pt3-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am57xx-beagle-x15: Fix USB2 mode
ARM: dts: am57xx-beagle-x15: Add extcon nodes for USB
ARM: dts: dra72-evm: Add extcon nodes for USB
ARM: dts: dra7-evm: Add extcon nodes for USB
ARM: dts: Fix dm816x pinctrl and syscon so they are children of SCM
ARM: dts: omap3-gta04: Disable keypad
ARM: dts: omap3-gta04: only power DSS when necessary.
ARM: dts: omap3-gta04: add gyroscope
ARM: dts: omap3-gta04: enable power-off for wifi card.
ARM: dts: omap3-gta04: add comments about gpios
ARM: dts: omap3-gta04: Add ramp value for twl4030 audio
ARM: dts: omap3-gta04: Enable power-off using twl4030
ARM: dts: omap3-gta04: Fix a GPIO line for bma180 node
ARM: dts: omap3-gta04: Enable twl audio vibra support
ARM: dts: omap3-gta04: Enable mcbps2 necessary for audio
ARM: dts: omap3-gta04: Fix audio node malformatting
ARM: dts: omap3-gta04: Fix backup-battery charging in devicetree file.
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt
Merge "ARM: rockchip: third (and last) batch of dts updates for 3.20" from
Heiko Stübner:
Change are regulator nodes for the cpu and gpu regulators on the act8846
variant of the rk3288-evb and the setting of a clock for the watchdog.
Also the lcd and hdmi controllers on both the firefly and the evb get
enabled and let us now boot into fbcon console sucessfully.
* tag 'v3.20-rockchip-dts3' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
ARM: dts: rockchip: move the hdmi ddc-i2c-bus property to the actual boards
ARM: dts: rockchip: enable vops and hdmi output on rk3288-firefly and -evb
ARM: dts: rockchip: housekeeping off i2c0 on rk3288-evb boards
ARM: dts: rockchip: add cpu and gpu regulators to rk3288-evb-act8846
ARM: dts: rockchip: add rk3288 watchdog clock
clk: rockchip: add id for watchdog pclk on rk3288
clk: rockchip: add clock IDs for the PVTM clocks
clk: rockchip: add clock ID for usbphy480m_src
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
http://github.com/broadcom/stblinux into next/fixes-non-critical
Merge "Fix git repositories for Broadcom SoCs (v3.20)" from Florian Fianelli:
This pull request fixes the github.com/broadcom URLs which had one too many
"git." in front of all git repositories.
* tag 'arm-soc/for-3.20/maintainer' of http://github.com/broadcom/stblinux:
MAINTAINERS: fix git repositories for Broadcom SoCs
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91 into next/soc
Merge "at91: cleanup/soc for 3.20 #4" from Nicolas Ferre:
Fourth cleanup/soc batch for 3.20:
- merge all the at91sam9 code and remove the empty SoC-specific files
- remove the at91_boot_soc that is now useless in a DT context
- move the sram code in PM code as it's now only used there
- some file + function name changes after this big cleanup
* tag 'at91-soc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
ARM: at91/trivial: unify functions and machine names
ARM: at91: remove at91_dt_initialize and machine init_early()
ARM: at91: change board files into SoC files
ARM: at91: remove at91_boot_soc
ARM: at91: move alternative initial mapping to board-dt-sama5.c
ARM: at91: merge all SOC_AT91SAM9xxx
ARM: at91: at91rm9200: set idle and restart from rm9200_dt_device_init()
ARM: at91: board-dt-sama5: add phy_fixup to override NAND_Tree
ARM: at91/dt: sam9263: Add missing clocks to lcdc node
ARM: at91: sama5d3: dt: correct the sound route
ARM: at91/dt: sama5d4: fix the timer reg length
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* Add support for beamforming
* Enable stuck queue detection for iwlmvm
* A few fixes for EBS scan
* Fixes for various failure paths
* Improvements for TDLS Offchannel
|
|
The functions brcmu_pkt_buf_free_skb() and usb_free_urb() test whether
their argument is NULL and then return immediately. Thus the test around
the call is not needed.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The kfree() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The relay_close() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
detection
The functions kfree() and release_firmware() were called in a few cases
by the cw1200_load_firmware_cw1200() function during error handling even if
the passed variables contained still a null pointer.
Corresponding implementation details could be improved by adjustments for
jump targets.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The release_firmware() function tests whether its argument is NULL and then
returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is only an API consolidation and should make things more readable
it replaces var * HZ / 1000 by msecs_to_jiffies(var).
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This is only an API consolidation to make things more readable.
Instances of HZ / CONST are replaced by appropriate msecs_to_jiffies().
Signed-off-by: Nicholas Mc Guire <hofrat@osadl.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Sometimes while CPU have some load and ath5k doing the wireless
interface reset the whole WiSoC completely freezes. Set of tests shows
that using atomic delay function while we wait interface reset helps to
avoid such freezes.
The easiest way to reproduce this issue: create a station interface,
start continous scan with wpa_supplicant and load CPU by something. Or
just create multiple station interfaces and put them all in continous
scan.
This patch partially reverts the commit 1846ac3dbec0 ("ath5k: Use
usleep_range where possible"), which replaces initial udelay()
by usleep_range().
I do not know actual source of this issue, but all looks like that HW
freeze is caused by transaction on internal SoC bus, while wireless
block is in reset state.
Also I should note that I do not know how many chips are affected, but I
did not see this issue with chips, other than AR5312.
CC: Jiri Slaby <jirislaby@gmail.com>
CC: Nick Kossifidis <mickflemm@gmail.com>
CC: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Fixes: 1846ac3dbec0 ("ath5k: Use usleep_range where possible")
Reported-by: Christophe Prevotaux <c.prevotaux@rural-networks.com>
Tested-by: Christophe Prevotaux <c.prevotaux@rural-networks.com>
Tested-by: Eric Bree <ebree@nltinc.com>
Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Set the transmit rate for the keep-alive frames
as 1M/CCK when the current channel is in the
2GHz band.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Chips in the AR9003 family have a second TSF, which
needs to be cleared when putting the card to
sleep.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Setting the required configuration in the PCIE
WorkAround register needs to be done after all the
WoW parameters have been set.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This patch addresses several issues with the
ath9k_hw_wow_enable() routine:
* The usage of set/clr variables is removed. Writing
the required values to registers is cleaner.
* The shift value of 28 for the contention window field
in AR_WOW_PATTERN is incorrect, change it to 27.
* Disabling Keep Alive needs to be done based on the
LINK_CHANGE option. This is done unconditionally now,
fix this.
* The workaround for the D1/D3 issue is required only
for AR9462.
* The bitfield for enabling pattern matching for packets
less than 256 bytes has expanded for new chips, handle
this accordingly.
* General cleanup.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Since the number of user patterns is higher for
newer chips, make sure that this is registered
during initialization.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Newer chips like WB222, WB335 support more than
8 user-configurable patterns. This patch adds
support for it by setting up the correct HW
registers.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This driver utilizes a FIFO buffer for RX descriptors. There are four places
in the code where it calculates the number of free slots. Several of those
locations do the calculation incorrectly. To fix these and to prevent future
mistakes, a common inline routine is created.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V3.18]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The hardware and firmware for the RTL8192EE utilize a FIFO list of
descriptors. There were some problems with the initial implementation.
The worst of these failed to detect that the FIFO was becoming full,
which led to the device needing to be power cycled. As this condition
is not relevant to most of the devices supported by rtlwifi, a callback
routine was added to detect this situation. This patch implements the
necessary changes in the pci handler, and the linkage into the appropriate
rtl8192ee routine.
Signed-off-by: Troy Tan <troy_tan@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@vger.kernel.org> [V3.18]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The Altera mailbox allows for interprocessor communication. It supports
only one channel and work as either sender or receiver.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
|
|
Before polling we just need to see if the TXDONE_BY_POLL bit
is set in txdone_method. There may be another bit (method)
specified as well, like TXDONE_BY_ACK.
Signed-off-by: Jassi Brar <jassisinghbrar@gmail.com>
|
|
In case of error, the function platform_create_bundle() returns
ERR_PTR() and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
|
|
The warning message when loading modules with a wrong signature has
two spaces in it:
"module verification failed: signature and/or required key missing"
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
parse_args call module parameters' .set handlers, which may use locks defined in the module.
So, these classes should be freed in case parse_args returns error(e.g. due to incorrect parameter passed).
Signed-off-by: Andrey Tsyvarev <tsyvarev@ispras.ru>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
These __ksymtab*/__kcrctab* sections currently have non-zero addresses.
Non-zero section addresses in a relocatable ELF confuse GDB and it ends
up not relocating all symbols when add-symbol-file is used on modules
which have exports. The kernel's module loader does not care about
these addresses, so let's just set them to zero.
Before:
$ readelf -S lib/notifier-error-inject.ko | grep 'Name\| __ksymtab_gpl'
[Nr] Name Type Addr Off Size ES Flg Lk Inf Al
[ 8] __ksymtab_gpl PROGBITS 0000000c 0001b4 000010 00 A 0 0 4
(gdb) add-symbol-file lib/notifier-error-inject.ko 0x500000 -s .bss 0x700000
add symbol table from file "lib/notifier-error-inject.ko" at
.text_addr = 0x500000
.bss_addr = 0x700000
(gdb) p ¬ifier_err_inject_dir
$3 = (struct dentry **) 0x0
After:
$ readelf -S lib/notifier-error-inject.ko | grep 'Name\| __ksymtab_gpl'
[Nr] Name Type Addr Off Size ES Flg Lk Inf Al
[ 8] __ksymtab_gpl PROGBITS 00000000 0001b4 000010 00 A 0 0 4
(gdb) add-symbol-file lib/notifier-error-inject.ko 0x500000 -s .bss 0x700000
add symbol table from file "lib/notifier-error-inject.ko" at
.text_addr = 0x500000
.bss_addr = 0x700000
(gdb) p ¬ifier_err_inject_dir
$3 = (struct dentry **) 0x700000
Signed-off-by: Rabin Vincent <rabin.vincent@axis.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
|
|
pnfs_layoutreturn_free_lseg_async() can also race with inode put in
the general case. We can now fix this, and also simplify the code.
Cc: Peng Tao <tao.peng@primarydata.com>
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>
|
|
In concat_read_oob both retlen and oobretlen should be updated.
concat_write_oob previously only (improperly) updated retlen.
Signed-off-by: Niklas Cassel <niklass@axis.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
The PPC_OF is a ppc specific option which is used to mean that the
firmware device tree access functions are available. Since all the
ppc platforms have a device tree, it is aways set to 'y' for ppc.
So it makes no sense to keep a such option in the current kernel.
Replace it with PPC.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
