| Age | Commit message (Collapse) | Author |
|---|
|
Add the missing HID supplies to avoid relying on other consumers to keep
them on.
This also avoids the following warnings on boot:
i2c_hid_of 0-0010: supply vdd not found, using dummy regulator
i2c_hid_of 0-0010: supply vddl not found, using dummy regulator
i2c_hid_of 1-0015: supply vdd not found, using dummy regulator
i2c_hid_of 1-0015: supply vddl not found, using dummy regulator
i2c_hid_of 1-003a: supply vdd not found, using dummy regulator
i2c_hid_of 1-003a: supply vddl not found, using dummy regulator
Note that VREG_MISC_3P3 is also used for things like the fingerprint
reader which are not yet fully described so mark the regulator as always
on for now.
Fixes: d7e03cce0400 ("arm64: dts: qcom: x1e80100-crd: Enable more support")
Reviewed-by: Abel Vesa <abel.vesa@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Link: https://lore.kernel.org/r/20241029075258.19642-1-johan+linaro@kernel.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add dmas and dma-names properties in spi nodes of stm32mp251.dtsi to
enable DMA support.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add dmas and dma-names properties in i2c nodes of stm32mp251.dtsi to
enable DMA support.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add dmas and dma-names properties in u(s)art nodes of stm32mp251.dtsi to
enable DMA support.
RX channel requires to prevent pack/unpack feature of DMA to avoid losing
bytes when interrupting RX transfer, as it uses a cyclic buffer.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Update the device-tree stm32mp251.dtsi by adding the Random Number
Generator(RNG) node.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Be default, R511 iand D19 are not populated on our phyBOARD-Electra.
This resistor and diode connect VCC_3V3_SW with VBAT and permanently
charge the RTC battery.
Enable trickle charge to charge the battery through the RTC.
Signed-off-by: Daniel Schultz <d.schultz@phytec.de>
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240911124251.702590-3-w.egorov@phytec.de
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Enable RTC on stm32mp257f-ev1 board.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add compatible, clock, and interrupt properties of STM32 RTC on
stm32mp25x SOCs.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add support of WLAN/BT Murata Type 1DX module:
- usart2 is used for Bluetooth interface
- sdmmc2 is used for WLAN (sdio) interface
Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add support of WLAN/BT Murata Type 1DX module:
- usart2 is used for Bluetooth interface
- sdmmc2 is used for WLAN (sdio) interface
Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
On stm32mp135f-dk board, WLAN/BT module LPO_IN pin is wired to
RTC OUT2_RMP pin.
Provide a pinctrl configuration to enable LSCO on OUT2_RMP.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
On stm32mp157c-dk2 board, WLAN/BT module LPO_IN pin is wired to
RTC OUT2_RMP pin.
Provide a pinctrl configuration to enable LSCO on OUT2_RMP.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Declare pin for LSCO in stm32-pinctrl provider node to reserve this pin
for RTC OUT2_RMP, in stm32mp13-pinctrl.dtsi.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Declare pin for LSCO in stm32-pinctrl provider node to reserve this pin
for RTC OUT2_RMP, in stm32mp15-pinctrl.dtsi.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
DHCOR SoM DT
The STM32MP13xx DHCOR SoM is populated with M24256E EEPROM which has
Additional Write lockable page at separate I2C address. Describe the
page in DT to make it available.
Note that the WLP page on this device is hardware write-protected by
R37 which pulls the nWC signal high to VDD_3V3_1V8 power rail.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
As most other board Miix uses board-id = 0xff, so define calibration
variant to distinguish it from other devices with the same chip_id.
qmi chip_id 0x30214 chip_family 0x4001 board_id 0xff soc_id 0x40010002
Cc: Kalle Valo <kvalo@kernel.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/r/20240723-miix630-support-v2-5-7d98f6047a17@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Let resin device generate the VolumeDown key.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/r/20240723-miix630-support-v2-4-7d98f6047a17@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Add gpio-keys device, responsible for a single button: Volume Up.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/r/20240723-miix630-support-v2-3-7d98f6047a17@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
Enable two other DSP instances on this platofm, aDSP and SLPI.
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/r/20240723-miix630-support-v2-2-7d98f6047a17@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
There is no point in keeping touchscreen disabled, enable corresponding
i2c-hid device.
04F3:2608 Touchscreen as /devices/platform/soc@0/c179000.i2c/i2c-0/0-0010/0018:04F3:2608.0001/input/input1
04F3:2608 as /devices/platform/soc@0/c179000.i2c/i2c-0/0-0010/0018:04F3:2608.0001/input/input2
04F3:2608 as /devices/platform/soc@0/c179000.i2c/i2c-0/0-0010/0018:04F3:2608.0001/input/input3
04F3:2608 Stylus as /devices/platform/soc@0/c179000.i2c/i2c-0/0-0010/0018:04F3:2608.0001/input/input4
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Jeffrey Hugo <quic_jhugo@quicinc.com>
Link: https://lore.kernel.org/r/20240723-miix630-support-v2-1-7d98f6047a17@linaro.org
Signed-off-by: Bjorn Andersson <andersson@kernel.org>
|
|
The IWDG2 is capable of generating pre-timeout interrupt, which can be used
to wake the system up from suspend to mem. Add the EXTI interrupt mapping
and mark the IWDG2 as wake up source.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The AM64x SoCs of the TI K3 family have a Cortex M4F core in the MCU
domain. This core can be used by non safety applications as a remote
processor. When used as a remote processor with virtio/rpmessage IPC,
two carveout reserved memory nodes are needed. The first region is used
as a DMA pool for the rproc device, and the second region will furnish
the static carveout regions for the firmware memory.
The current carveout addresses and sizes are defined statically for
each rproc device. The M4F processor does not have an MMU, and as such
requires the exact memory used by the firmware to be set-aside.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240911124251.702590-2-w.egorov@phytec.de
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The AM62x SoCs of the TI K3 family have a Cortex M4F core in the MCU
domain. This core can be used by non safety applications as a remote
processor. When used as a remote processor with virtio/rpmessage IPC,
two carveout reserved memory nodes are needed. The first region is used
as a DMA pool for the rproc device, and the second region will furnish
the static carveout regions for the firmware memory.
The current carveout addresses and sizes are defined statically for
each rproc device. The M4F processor does not have an MMU, and as such
requires the exact memory used by the firmware to be set-aside.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Link: https://lore.kernel.org/r/20240911124251.702590-1-w.egorov@phytec.de
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The DTS code coding style expects exactly one space before '{'
character.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20240905154440.424488-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Corrected the indentation for the audio card node in the phyBOARD-Lyra.
Signed-off-by: John Ma <jma@phytec.com>
Link: https://lore.kernel.org/r/20240926184849.3341986-1-jma@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
nodes
The bus-width property was moved to k3-am64-main.dtsi.
See commit 0ae3113a46a6 ("arm64: dts: ti: k3-am6*: Fix bus-width property
in MMC nodes")
Signed-off-by: John Ma <jma@phytec.com>
Link: https://lore.kernel.org/r/20240926184918.3342719-2-jma@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The bus-width property was moved to k3-am64-main.dtsi.
See commit 0ae3113a46a6 ("arm64: dts: ti: k3-am6*: Fix bus-width property
in MMC nodes")
Signed-off-by: John Ma <jma@phytec.com>
Link: https://lore.kernel.org/r/20240926184918.3342719-1-jma@phytec.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add overlay to enable the PCIe0 instance of PCIe on AM642-EVM in
Endpoint mode of operation.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20240930103413.3085689-1-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add overlay to enable the PCIE1 instance of PCIe on J7200-EVM in
Endpoint mode of operation.
Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Link: https://lore.kernel.org/r/20241001093426.3401765-1-s-vadapalli@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Update itap/itap values according to device datasheet [0].
Now that we have fixed timing issues for am62x [1], lets
change the otap/itap values back according to the device
datasheet.
[0] https://www.ti.com/lit/ds/symlink/am625.pdf
[1] https://lore.kernel.org/linux-mmc/20240913185403.1339115-1-jm@ti.com/
Signed-off-by: Judith Mendez <jm@ti.com>
Reviewed-by: Bhavya Kapoor <b-kapoor@ti.com>
Link: https://lore.kernel.org/r/20240924195335.546900-1-jm@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add pinmux for PWM functionality of MikroBUS PWM pin and enable the pwm
controller.
Signed-off-by: Ayush Singh <ayush@beagleboard.org>
Link: https://lore.kernel.org/r/20241016-beagleplay-pwm-v1-1-245ae88859bc@beagleboard.org
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The power switch used to power the SD card interface might have
more than 2ms turn-on time, increase the startup delay to 20ms to
prevent failures.
Fixes: 316b80246b16 ("arm64: dts: ti: add verdin am62")
Cc: stable@vger.kernel.org
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20241024130628.49650-1-francesco@dolcini.it
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Fix Verdin AM62 on-SOM ADC compatible. Currently the hardware is not
correctly described in the DT, use the correct TI TLA2024 compatible that
matches what is assembled on the board.
The "ti,tla2024" compatible was introduced in Linux v5.19 and Verdin AM62
support was introduced in Linux v6.5.
The new DTB will not work on kernel older than v5.19, but this seems
unlikely to happen. U-Boot does not use the ADC node and a known Android 14
out-of-tree port uses a Linux Kernel 6.1.
With that said, despite this being a breaking change, it seems fair to
to not expect any regression because of it.
Signed-off-by: João Paulo Gonçalves <joao.goncalves@toradex.com>
Link: https://lore.kernel.org/r/20241015113334.246110-1-jpaulo.silvagoncalves@gmail.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Add on-SOM TPM device to the device tree file.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20241018170436.80010-1-francesco@dolcini.it
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The clock IDs for multiple MCSPI instances across wakeup domain
in J721s2 are incorrect when compared with documentation [1]. Fix the
clock IDs to their appropriate values.
[1]https://software-dl.ti.com/tisci/esd/latest/5_soc_doc/j721s2/clocks.html
Fixes: 04d7cb647b85 ("arm64: dts: ti: k3-j721s2: Add MCSPI nodes")
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
Link: https://lore.kernel.org/r/20241023104532.3438851-4-a-dutta@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The clock IDs for multiple MCSPI instances across wakeup domain
in J721e are incorrect when compared with documentation [1]. Fix
the clock ids to their appropriate values.
[1]https://software-dl.ti.com/tisci/esd/latest/5_soc_doc/j721e/clocks.html
Fixes: 76aa309f9fa7 ("arm64: dts: ti: k3-j721e: Add MCSPI nodes")
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
Link: https://lore.kernel.org/r/20241023104532.3438851-3-a-dutta@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The clock IDs for multiple MCSPI instances across wakeup as
well as main domain in J7200 are incorrect when compared with
documentation [1]. This results in kernel crashes when the said
instances are enabled. Fix the clock ids to their appropriate
values.
[1]https://software-dl.ti.com/tisci/esd/latest/5_soc_doc/j7200/clocks.html
Fixes: 8f6c475f4ca7 ("arm64: dts: ti: k3-j7200: Add MCSPI nodes")
Signed-off-by: Anurag Dutta <a-dutta@ti.com>
Reviewed-by: Aniket Limaye <a-limaye@ti.com>
Link: https://lore.kernel.org/r/20241023104532.3438851-2-a-dutta@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Commit 0d0a0b441346 ("arm64: dts: ti: k3-j7200: fix main pinmux
range") split the main_pmx0 into two nodes: main_pmx0 and main_pmx1
due to a non-addressable region, but incorrectly represented the
ranges. As a result, the memory map for the pinctrl is incorrect. Fix
this by introducing the correct ranges.
The ranges are taken from the J7200 TRM [1] (Table 5-695. CTRL_MMR0
Registers).
Padconfig starting addresses and ranges:
- 0 to 66: 0x11c000, 0x10c
- 68: 0x11c110, 0x004
- 71 to 73: 0x11c11c, 0x00c
- 89 to 90: 0x11c164, 0x008
The datasheet [2] doesn't contain PADCONFIG63 (Table 6-106. Pin
Multiplexing), but the pin is necessary for enabling the MMC1 CLKLP
pad loopback and should be included in the pinmux register map.
Due to the change in pinmux node addresses, change the pinmux node for
the USB0_DRVVBUS pin to main_pmx2. The offset has not changed since the
new main_pmx2 node has the same base address and range as the original
main_pmx1 node. All other pinmuxing done within J7200 dts or dtso files
only uses main_pmx0 which has not changed.
[1] https://www.ti.com/lit/pdf/spruiu1
[2] https://www.ti.com/lit/gpn/dra821u
Fixes: 0d0a0b441346 ("arm64: dts: ti: k3-j7200: fix main pinmux range")
Signed-off-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Jared McArthur <j-mcarthur@ti.com>
Reviewed-by: Vaishnav Achath <vaishnav.a@ti.com>
Link: https://lore.kernel.org/r/20240926102533.398139-1-a-limaye@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Adds bootph-* properties to the leaf nodes to enable bootloaders to
utilise them.
Following adds bootph-* to:
- pmic regulator for enabling AVS Support
- main_uart0, mcu_uart0(DM), wkup_uart0(TIFS) for Traces
- mmc0, mmc1, usb0, ospi0, hbmc for enabling various bootmodes.
Reviewed-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Link: https://lore.kernel.org/r/20241024-b4-upstream-bootph-all-v6-12-2af90e3a4fe7@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Adds bootph-* properties to the leaf nodes to enable bootloaders to
utilise them.
Following adds bootph-* to:
- main_uart0, mcu_uart0(DM), wkup_uart0(TIFS) for Traces
- mmc1, usb0, usb1, ospi0 for enabling various bootmodes.
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Link: https://lore.kernel.org/r/20241024-b4-upstream-bootph-all-v6-11-2af90e3a4fe7@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Adds bootph-* properties to the leaf nodes to enable bootloaders to
utilise them.
Following adds bootph-* to:
- main_uart0, mcu_uart0(DM), wkup_uart0(TIFS) for Traces
- mmc0, mmc1, usb0, ospi0, ospi1, hbmc for enabling various bootmodes.
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Link: https://lore.kernel.org/r/20241024-b4-upstream-bootph-all-v6-10-2af90e3a4fe7@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Adds bootph-* properties to the leaf nodes to enable bootloaders to
utilise them.
Following adds bootph-* to:
- main_uart8, mcu_uart0(DM), wkup_uart0(TIFS) for Traces
- mmc1, ospi0 for enabling various bootmodes.
- eeprom for board detection
Reviewed-by: Udit Kumar <u-kumar1@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Link: https://lore.kernel.org/r/20241024-b4-upstream-bootph-all-v6-9-2af90e3a4fe7@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Adds bootph-* properties to the leaf nodes to enable bootloaders to
utilise them.
Following adds bootph-* to:
- pmic regulator for enabling AVS Support
- main_uart8, mcu_uart0(DM), wkup_uart0(TIFS) for Traces
- mmc0, mmc1, usb0, ospi0, ospi1 for enabling various bootmodes.
Reviewed-by: Andrew Davis <afd@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Link: https://lore.kernel.org/r/20241024-b4-upstream-bootph-all-v6-8-2af90e3a4fe7@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Adding bootph properties on leaf nodes imply that they are applicable to
the parent nodes as well. Bootloaders can derive the parent nodes when
bootph is available in the leaf nodes.
Remove the bootph-* properties from parent nodes as they are redundant.
Reviewed-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Link: https://lore.kernel.org/r/20241024-b4-upstream-bootph-all-v6-7-2af90e3a4fe7@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Adds bootph-* properties to the leaf nodes to enable bootloaders to
utilise them.
Following adds bootph-* to
- System controller nodes that allow controlling power domain, clocks, etc.
- secure_proxy_sa3/secure_proxy_main mboxes for communication with
System Controller
- mcu_ringacc/mcu_udmap for DMA to SMS
- chipid for detection soc information.
- mcu_timer0 for bootloader tick-timer.
- hbmc_mux for enabling Hyperflash support
- ESM nodes for enabling ESM support.
- wkup_vtm for enabling Adaptive voltage scaling(AVS) support
Reviewed-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Link: https://lore.kernel.org/r/20241024-b4-upstream-bootph-all-v6-6-2af90e3a4fe7@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Adds bootph-* properties to the leaf nodes to enable bootloaders to
utilise them.
Following adds bootph-* to
- System controller nodes that allow controlling power domain, clocks, etc.
- secure_proxy_sa3/secure_proxy_main mboxes for communication with
System Controller
- mcu_ringacc/mcu_udmap for DMA to SMS
- chipid for detection soc information.
- mcu_timer0 for bootloader tick-timer.
- hbmc_mux for enabling Hyperflash support
- ESM nodes for enabling ESM support.
- wkup_vtm for enabling Adaptive voltage scaling(AVS) support
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Link: https://lore.kernel.org/r/20241024-b4-upstream-bootph-all-v6-5-2af90e3a4fe7@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Adds bootph-* properties to the leaf nodes to enable bootloaders to
utilise them.
Following adds bootph-* to
- System controller nodes that allow controlling power domain, clocks, etc.
- secure_proxy_sa3/secure_proxy_main mboxes for communication with
System Controller
- mcu_ringacc/mcu_udmap for DMA to SMS
- chipid for detection soc information.
- mcu_timer0 for bootloader tick-timer.
- wkup_vtm for enabling Adaptive voltage scaling(AVS) support
Reviewed-by: Andrew Davis <afd@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Link: https://lore.kernel.org/r/20241024-b4-upstream-bootph-all-v6-4-2af90e3a4fe7@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
The following nodes are being used in the bootloaders. Adds bootph-*
properties to the leaf nodes to enable bootloaders to utilise them.
Following adds bootph-* to
- secure_proxy_sa3/secure_proxy_main mboxes for communication with
System Controller
- wkup_vtm for enabling Adaptive voltage scaling(AVS) support
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Link: https://lore.kernel.org/r/20241024-b4-upstream-bootph-all-v6-3-2af90e3a4fe7@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
Adding bootph properties on leaf nodes imply that they are applicable to
the parent nodes as well. Bootloaders can derive the parent nodes when
bootph is available in the leaf nodes.
Remove the bootph-* properties from parent nodes as they are redundant.
Reviewed-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Link: https://lore.kernel.org/r/20241024-b4-upstream-bootph-all-v6-2-2af90e3a4fe7@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
|
mcu_timer0
Bootloader are using mcu_timer0 instead of mcu_timer1. Adds bootph to
mcu_timer0 instead of mcu_timer1.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Link: https://lore.kernel.org/r/20241024-b4-upstream-bootph-all-v6-1-2af90e3a4fe7@ti.com
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
|
