| Age | Commit message (Collapse) | Author |
|---|
|
Short story: Exception handlers used by some copy_to_user() and
copy_from_user() functions do not diligently clean up floating point
register usage, and this can result in a user process seeing invalid
values in floating point registers. This sometimes makes the process
fail.
Long story: Several cpu-specific (NG4, NG2, U1, U3) memcpy functions
use floating point registers and VIS alignaddr/faligndata to
accelerate data copying when source and dest addresses don't align
well. Linux uses a lazy scheme for saving floating point registers; It
is not done upon entering the kernel since it's a very expensive
operation. Rather, it is done only when needed. If the kernel ends up
not using FP regs during the course of some trap or system call, then
it can return to user space without saving or restoring them.
The various memcpy functions begin their FP code with VISEntry (or a
variation thereof), which saves the FP regs. They conclude their FP
code with VISExit (or a variation) which essentially marks the FP regs
"clean", ie, they contain no unsaved values. fprs.FPRS_FEF is turned
off so that a lazy restore will be triggered when/if the user process
accesses floating point regs again.
The bug is that the user copy variants of memcpy, copy_from_user() and
copy_to_user(), employ an exception handling mechanism to detect faults
when accessing user space addresses, and when this handler is invoked,
an immediate return from the function is forced, and VISExit is not
executed, thus leaving the fprs register in an indeterminate state,
but often with fprs.FPRS_FEF set and one or more dirty bits. This
results in a return to user space with invalid values in the FP regs,
and since fprs.FPRS_FEF is on, no lazy restore occurs.
This bug affects copy_to_user() and copy_from_user() for NG4, NG2,
U3, and U1. All are fixed by using a new exception handler for those
loads and stores that are done during the time between VISEnter and
VISExit.
n.b. In NG4memcpy, the problematic code can be triggered by a copy
size greater than 128 bytes and an unaligned source address. This bug
is known to be the cause of random user process memory corruptions
while perf is running with the callgraph option (ie, perf record -g).
This occurs because perf uses copy_from_user() to read user stacks,
and may fault when it follows a stack frame pointer off to an
invalid page. Validation checks on the stack address just obscure
the underlying problem.
Signed-off-by: Rob Gardner <rob.gardner@oracle.com>
Signed-off-by: Dave Aldridge <david.j.aldridge@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There have been several reports of random processes being killed with
a bus error or segfault during userspace stack walking in perf. One
of the root causes of this problem is an asynchronous modification to
thread_info fault_address and fault_code, which stems from a perf
counter interrupt arriving during kernel processing of a "benign"
fault, such as a TSB miss. Since perf_callchain_user() invokes
copy_from_user() to read user stacks, a fault is not only possible,
but probable. Validity checks on the stack address merely cover up the
problem and reduce its frequency.
The solution here is to save and restore fault_address and fault_code
in perf_callchain_user() so that the benign fault handler is not
disturbed by a perf interrupt.
Signed-off-by: Rob Gardner <rob.gardner@oracle.com>
Signed-off-by: Dave Aldridge <david.j.aldridge@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When an interrupt (such as a perf counter interrupt) is delivered
while executing in user space, the trap entry code puts ASI_AIUS in
%asi so that copy_from_user() and copy_to_user() will access the
correct memory. But if a perf counter interrupt is delivered while the
cpu is already executing in kernel space, then the trap entry code
will put ASI_P in %asi, and this will prevent copy_from_user() from
reading any useful stack data in either of the perf_callchain_user_X
functions, and thus no user callgraph data will be collected for this
sample period. An additional problem is that a fault is guaranteed
to occur, and though it will be silently covered up, it wastes time
and could perturb state.
In perf_callchain_user(), we ensure that %asi contains ASI_AIUS
because we know for a fact that the subsequent calls to
copy_from_user() are intended to read the user's stack.
[ Use get_fs()/set_fs() -DaveM ]
Signed-off-by: Rob Gardner <rob.gardner@oracle.com>
Signed-off-by: Dave Aldridge <david.j.aldridge@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 28a1f53 delays setting %pil to avoid potential
hardirq stack overflow in the common rtrap_irq path.
Setting %pil also needs to be delayed in the rtrap_nmi
path for the same reason.
Signed-off-by: Rob Gardner <rob.gardner@oracle.com>
Signed-off-by: Dave Aldridge <david.j.aldridge@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add ADI (Application Data Integrity) capability to cpu capabilities list.
ADI capability allows virtual addresses to be encoded with a tag in
bits 63-60. This tag serves as an access control key for the regions
of virtual address with ADI enabled and a key set on them. Hypervisor
encodes this capability as "adp" in "hwcap-list" property in machine
description.
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Constifies sunhv_ops structures in tty's serial
driver since they are not modified after their
initialization.
Detected and found using Coccinelle.
Suggested-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Aya Mahfouz <mahfouz.saif.elyazal@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove deprecated module parameters, and mark one parameter as
deprecated.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CLIP is always enabled and hardware uses 2 TID entries instead of 4 for
IPv6 in CLIP mode.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the original code, if we succeeded on the last iteration through the
loop then we still returned failure.
Fixes: 389e4e04ad2d ('qlcnic: fix a timeout loop')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a signedness bug here so the loop will never exit.
Fixes: 8bfcbbbcabe0 ('pinctrl: nsp: add gpio-a driver support for Broadcom NSP SoC')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into devel
Exynos-specific drivers for 4.5:
1. Add a pinctrl driver for Exynos5410.
|
|
NCM buffer sizes are negotiated with the device independently of
the network device MTU. The RX buffers are allocated by the
usbnet framework based on the rx_urb_size value set by cdc_ncm. A
single RX buffer can hold a number of MTU sized packets.
The default usbnet change_mtu ndo only modifies rx_urb_size if it
is equal to hard_mtu. And the cdc_ncm driver will set rx_urb_size
and hard_mtu independently of each other, based on dwNtbInMaxSize
and dwNtbOutMaxSize respectively. It was therefore assumed that
usbnet_change_mtu() would never touch rx_urb_size. This failed to
consider the case where dwNtbInMaxSize and dwNtbOutMaxSize happens
to be equal.
Fix by implementing an NCM specific change_mtu ndo, modifying the
netdev MTU without touching the buffer size settings.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hariprasad Shenai says:
====================
Update support for T6 adapters
This patch changes updates the various code changes related to
register, stats and hardware related changes for T6 family of
adapters.
This patch series has been created against net-next tree and includes
patches on cxgb4 and cxgb4vf driver.
We have included all the maintainers of respective drivers. Kindly review
the change and let us know in case of any review comments.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SGE context congestion map changed from 4 to 8 priority per port
in T6 as there are only 2 channels.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In T6, MPS classification has a 512 deep TCAM to do the match lookup.
Each entry has 80x2b sets containing 48 bit MAC address, port number,
VLAN Valid/ID, VNI, lookup type (outer or inner packet header).
[71:48] bit locations are overloaded for outer vs. inner lookup types.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Updating Congestion Channel/Priority Map in Congestion Manager Context
for T6. In T6 port 0 is mapped to channel 0 and port 1 is mapped to
channel 1. For 2 port T4/T5 adapter, port 0 is mapped to channel 0,1 and
port 1 is mapped to channel 2,3
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ingress padding boundary values got changed for T6.
T5: 0=32B 1=64B 2=128B 3=256B 4=512B 5=1024B 6=2048B 7=4096B
T6: 0=8B 1=16B 2=32B 3=64B 4=128B 5=128B 6=256B 7=512B
Updating the driver to set the correct boundary values in SGE_CONTROL to
32B.
Also, need to take care of this fl alignment change when calculating the
next packet offset.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Updated pm_stats code to display input FIFO wait (index 5) and read
latency (index 7) counters for T6 adapters
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the needed_headroom field for the geneve device is left
to the default value.
This patch set it to space required for basic geneve encapsulation,
so that we can avoid the skb head re-allocation on xmit.
This give a 6% speedup for unsegment traffic on geneve tunnel.
v1 -> v2:
- add ETH_HLEN for the lower device to the needed headroom
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
kobj_to_dev has been defined in linux/device.h, so I replace to_dev
with it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
to_dev is not used anymore so drop it.
Signed-off-by: Geliang Tang <geliangtang@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The 6320 family of switch chips has a second bank for statistics, but
is missing three statistics in the port registers. Generalise and
extend the code:
* adding a field to the statistics table indicating the bank/register
set where each statistics is.
* add a function indicating if an individual statistics
is available on this device
* calculate at run time the sset_count.
* return strings based on the available statistics of the device
* return statistics based on the available statistics of the device
* Add support for reading from the second bank.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Bert Kenward says:
====================
sfc: additional virtual function support
This introduces the client side of a mechanism to defer authorisation of
operations, for example multicast subscription. Although primarily aimed at
SRIOV VFs this can also apply to unprivileged PFs.
Also handle reboot ordering corner cases better and reduce the level of some
logging.
v2: remove #ifdef DEBUG around new WARN_ON in mcdi.c.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Depending on configuration the NIC may return errors for unprivileged
functions and/or VFs. Where these are expected and handled, reduce the
level of any output.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running in an unprivileged function we expect some MC commands
to fail with permission errors. To avoid log spew downgrade these to
debug only.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are situations - mostly reset related - where our view of the
filter table differs from the hardware. In this case we may try and
remove filters that aren't actually installed. This isn't that
interesting in most situations, so downgrade the logging.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For unprivileged functions operations can be authorised by an admin
function. Extra steps are introduced to the MCDI protocol in this
situation - the initial response from the MCDI tells us that the
operation has been deferred, and we must retry when told. We then
receive an event telling us to retry.
Note that this provides only the functionality for the unprivileged
functions, not the handling of the administrative side.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After reboot the vswitch configuration from the PF may not be
complete before the VF attempts to restore filters. In that
case we see NO_EVB_PORT errors from the MC. Retry up to a time
limit or until a different result is seen.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Marc Haber reported we don't honor interface indexes when we receive link
local router addresses in router advertisements. Luckily the non-strict
version of ipv6_chk_addr already does the correct job here, so we can
simply use it to lighten the checks and use those addresses by default
without any configuration change.
Link: <http://permalink.gmane.org/gmane.linux.network/391348>
Reported-by: Marc Haber <mh+netdev@zugschlus.de>
Cc: Marc Haber <mh+netdev@zugschlus.de>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "domain" variable needs to be signed for the error handling to work.
Fixes: 8def31034d03 (cpufreq: arm_big_little: add SCPI interface driver)
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
After hooking up system call, userfaultfd selftest was successful for
both 32 and 64 bit version of test.
Signed-off-by: Mike Kravetz <mike.kravetz@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The file tracing_enable is obsolete and does not exist anymore. Replace
the comment that references it with the proper tracing_on file.
Link: http://lkml.kernel.org/r/1450787141-45544-1-git-send-email-chuhu@redhat.com
Signed-off-by: Chuyu Hu <chuhu@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
There is no need to worry about module and __init text disappearing
case, because that ftrace has a module notifier that is called when
a module is being unloaded and before the text goes away and this
code grabs the ftrace_lock mutex and removes the module functions
from the ftrace list, such that it will no longer do any
modifications to that module's text, the update to make functions
be traced or not is done under the ftrace_lock mutex as well.
And by now, __init section codes should not been modified
by ftrace, because it is black listed in recordmcount.c and
ignored by ftrace.
Link: http://lkml.kernel.org/r/1449367378-29430-3-git-send-email-huawei.libin@huawei.com
Cc: linux-metag@vger.kernel.org
Acked-by: James Hogan <james.hogan@imgtec.com>
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Li Bin <huawei.libin@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
There is no need to worry about module and __init text disappearing
case, because that ftrace has a module notifier that is called when
a module is being unloaded and before the text goes away and this
code grabs the ftrace_lock mutex and removes the module functions
from the ftrace list, such that it will no longer do any
modifications to that module's text, the update to make functions
be traced or not is done under the ftrace_lock mutex as well.
And by now, __init section codes should not been modified
by ftrace, because it is black listed in recordmcount.c and
ignored by ftrace.
Link: http://lkml.kernel.org/r/1449367378-29430-5-git-send-email-huawei.libin@huawei.com
Cc: linux-sh@vger.kernel.org
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Li Bin <huawei.libin@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
There is no need to worry about module and __init text disappearing
case, because that ftrace has a module notifier that is called when
a module is being unloaded and before the text goes away and this
code grabs the ftrace_lock mutex and removes the module functions
from the ftrace list, such that it will no longer do any
modifications to that module's text, the update to make functions
be traced or not is done under the ftrace_lock mutex as well.
And by now, __init section codes should not been modified
by ftrace, because it is black listed in recordmcount.c and
ignored by ftrace.
Link: http://lkml.kernel.org/r/1449214067-12177-2-git-send-email-huawei.libin@huawei.com
Cc: linux-ia64@vger.kernel.org
Acked-by: Tony Luck <tony.luck@intel.com>
Suggested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Li Bin <huawei.libin@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
The start and end variables were only used when ftrace_module_init() was
split up into multiple functions. No need to keep them around after the
merger.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Simple cleanup. No need for two functions here.
The whole work can simply be done inside 'ftrace_module_init'.
Link: http://lkml.kernel.org/r/1449067197-5718-1-git-send-email-abelvesa@linux.com
Signed-off-by: Abel Vesa <abelvesa@linux.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
TRACE_EVENT_FN can't be used in some circumstances
like invoking trace functions from offlined CPU due
to RCU usage.
This patch adds the TRACE_EVENT_FN_COND macro
to make such trace points conditional.
Link: http://lkml.kernel.org/r/1450124286-4822-1-git-send-email-kda@linux-powerpc.org
Signed-off-by: Denis Kirjanov <kda@linux-powerpc.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
commit 5ac48378414d ("tracing: Use trace_seq_used() and seq_buf_used()
instead of len") changed the tracing code to use trace_seq_used() and
seq_buf_used() instead of using the seq_buf len directly to avoid
overflow issues, but missed a spot in seq_buf_to_user() that makes use
of s->len.
Cleaned up the code a bit as well per suggestion of Steve Rostedt.
Link: http://lkml.kernel.org/r/1447703848-2951-1-git-send-email-jsnitsel@redhat.com
Signed-off-by: Jerry Snitselaar <jsnitsel@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
This bpf_verifier_ops structure is never modified, like the other
bpf_verifier_ops structures, so declare it as const.
Done with the help of Coccinelle.
Link: http://lkml.kernel.org/r/1449855359-13724-1-git-send-email-Julia.Lawall@lip6.fr
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Jiri Olsa noted that the change to replace the control_ops did not update
the trampoline for when running perf on a single CPU and with CONFIG_PREEMPT
disabled (where dynamic ops, like perf, can use trampolines directly). The
result was that perf function could be called when RCU is not watching as
well as not handle the ftrace_local_disable().
Modify the ftrace_ops_get_func() to also check the RCU and PER_CPU ops flags
and use the recursive function if they are set. The recursive function is
modified to check those flags and execute the appropriate checks if they are
set.
Link: http://lkml.kernel.org/r/20151201134213.GA14155@krava.brq.redhat.com
Reported-by: Jiri Olsa <jolsa@redhat.com>
Patch-fixed-up-by: Jiri Olsa <jolsa@redhat.com>
Tested-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
Currently perf has its own list function within the ftrace infrastructure
that seems to be used only to allow for it to have per-cpu disabling as well
as a check to make sure that it's not called while RCU is not watching. It
uses something called the "control_ops" which is used to iterate over ops
under it with the control_list_func().
The problem is that this control_ops and control_list_func unnecessarily
complicates the code. By replacing FTRACE_OPS_FL_CONTROL with two new flags
(FTRACE_OPS_FL_RCU and FTRACE_OPS_FL_PER_CPU) we can remove all the code
that is special with the control ops and add the needed checks within the
generic ftrace_list_func().
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
When showing all tramps registered to a ftrace record in the file
enabled_functions, it exits the loop with ops == NULL. But then it is
suppose to show the function on the ops->trampoline and
add_trampoline_func() is called with the given ops. But because ops is now
NULL (to exit the loop), it always shows the static trampoline instead of
the one that is really registered to the record.
The call to add_trampoline_func() that shows the trampoline for the given
ops needs to be called at every iteration.
Fixes: 39daa7b9e895 "ftrace: Show all tramps registered to a record on ftrace_bug()"
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
s/ARCH_SUPPORT_FTARCE_OPS/ARCH_SUPPORTS_FTRACE_OPS/
Link: http://lkml.kernel.org/r/1448879016-8659-1-git-send-email-huawei.libin@huawei.com
Signed-off-by: Li Bin <huawei.libin@huawei.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"This shouldn't be a nightmare before Christmas: just a handful small
device-specific fixes for various ASoC and HD-audio drivers. Most of
them are stable fixes"
* tag 'sound-4.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Fix silent headphone output on MacPro 4,1 (v2)
ASoC: fsl_sai: fix no frame clk in master mode
ALSA: hda - Set SKL+ hda controller power at freeze() and thaw()
ASoC: sgtl5000: fix VAG power up timing
ASoC: rockchip: spdif: Set transmit data level to 16 samples
ASoC: wm8974: set cache type for regmap
ASoC: es8328: Fix shifts for mixer switches
ASoC: davinci-mcasp: Fix XDATA check in mcasp_start_tx
ASoC: es8328: Fix deemphasis values
|
|
git://anongit.freedesktop.org/drm-intel
Pull i915 drm fixes from Jani Nikula:
"Here's a batch of i915 fixes all around. It may be slightly bigger
than one would hope for at this stage, but they've all been through
testing in our -next before being picked up for v4.4. Also, I missed
Dave's fixes pull earlier today just because I wanted an extra testing
round on this. So I'm fairly confident.
Wishing you all the things it is customary to wish this time of the
year"
* tag 'drm-intel-fixes-2015-12-23' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Correct max delay for HDMI hotplug live status checking
drm/i915: mdelay(10) considered harmful
drm/i915: Kill intel_crtc->cursor_bo
drm/i915: Workaround CHV pipe C cursor fail
drm/i915: Only spin whilst waiting on the current request
drm/i915: Limit the busy wait on requests to 5us not 10ms!
drm/i915: Break busywaiting for requests on pending signals
drm/i915: Disable primary plane if we fail to reconstruct BIOS fb (v2)
drm/i915: Set the map-and-fenceable flag for preallocated objects
drm/i915: Drop the broken cursor base==0 special casing
|
