| Age | Commit message (Collapse) | Author |
|---|
|
The GPIO block for ls2080a platform has little endian registers,
the GPIO driver needs this property to read/write registers by
right interface.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
The GPIO block on different QorIQ chips could have registers in different
endianess. Define the property to specify which endian is used by the
hardware.
Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
Add the "little-endian" property to fix the issue that eSDHC
is not working and dumping out "mmc0: Controller never released
inhibit bit(s)." error messages constantly.
Fixes: 5461597f6ce0 ("dts/ls2080a: Update DTSI to add support of various peripherals")
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kevin Hilman <khilman@linaro.org>
|
|
Some USB device / host controller combinations seem to have problems
with Link Power Management. For example, Steinar found that his xHCI
controller wouldn't handle bandwidth calculations correctly for two
video cards simultaneously when LPM was enabled, even though the bus
had plenty of bandwidth available.
This patch introduces a new quirk flag for devices that should remain
disabled for LPM, and creates quirk entries for Steinar's devices.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Steinar H. Gunderson <sgunderson@bigfoot.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
According to USB 2 specs ports need to signal resume for at least 20ms,
in practice even longer, before moving to U0 state.
Both host and devices can initiate resume.
On device initiated resume, a port status interrupt with the port in resume
state in issued. The interrupt handler tags a resume_done[port]
timestamp with current time + USB_RESUME_TIMEOUT, and kick roothub timer.
Root hub timer requests for port status, finds the port in resume state,
checks if resume_done[port] timestamp passed, and set port to U0 state.
On host initiated resume, current code sets the port to resume state,
sleep 20ms, and finally sets the port to U0 state. This should also
be changed to work in a similar way as the device initiated resume, with
timestamp tagging, but that is not yet tested and will be a separate
fix later.
There are a few issues with this approach
1. A host initiated resume will also generate a resume event. The event
handler will find the port in resume state, believe it's a device
initiated resume, and act accordingly.
2. A port status request might cut the resume signalling short if a
get_port_status request is handled during the host resume signalling.
The port will be found in resume state. The timestamp is not set leading
to time_after_eq(jiffies, timestamp) returning true, as timestamp = 0.
get_port_status will proceed with moving the port to U0.
3. If an error, or anything else happens to the port during device
initiated resume signalling it will leave all the device resume
parameters hanging uncleared, preventing further suspend, returning
-EBUSY, and cause the pm thread to busyloop trying to enter suspend.
Fix this by using the existing resuming_ports bitfield to indicate that
resume signalling timing is taken care of.
Check if the resume_done[port] is set before using it for timestamp
comparison, and also clear out any resume signalling related variables
if port is not in U0 or Resume state
This issue was discovered when a PM thread busylooped, trying to runtime
suspend the xhci USB 2 roothub on a Dell XPS
Cc: stable <stable@vger.kernel.org>
Reported-by: Daniel J Blueman <daniel@quora.org>
Tested-by: Daniel J Blueman <daniel@quora.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Even if dev->driver is null because we are being removed,
it is safer to not leave device locked.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Reviewed-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Reviewed-by: Vishal Verma <vishal.l.verma@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
The Atmel maxtouch DT binding documents that the compatible string for
the device is "atmel,maxtouch" and the I2C core always reports a module
alias of the form i2c:alias where alias is the compatible string model:
$ grep MODALIAS /sys/devices/platform/12e00000.i2c/i2c-8/8-004b/uevent
MODALIAS=i2c:maxtouch
But there isn't maxtouch entry in the I2C device ID table so when the
i2c:maxtouch MODALIAS uevent is reported, kmod is not able to match the
alias with a module to load:
$ modinfo atmel_mxt_ts | grep alias
alias: of:N*T*Catmel,maxtouch
alias: i2c:mXT224
alias: i2c:atmel_mxt_tp
alias: i2c:atmel_mxt_ts
alias: i2c:qt602240_ts
So add the maxtouch entry to the I2C device ID table to allow the module
to be autoloaded when the device is registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
KASAN found that our additional element processing scripts drop off
the end of the VPD page into unallocated space. The reason is that
not every element has additional information but our traversal
routines think they do, leading to them expecting far more additional
information than is present. Fix this by adding a gate to the
traversal routine so that it only processes elements that are expected
to have additional information (list is in SES-2 section 6.1.13.1:
Additional Element Status diagnostic page overview)
Reported-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Tested-by: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Five stable fixes:
- Two DM btree bufio buffer leak fixes that resolve reported BUG_ONs
during DM thinp metadata close's dm_bufio_client_destroy().
- A DM thinp range discard fix to handle discarding a partially
mapped range.
- A DM thinp metadata snapshot fix to make sure the btree roots saved
in the metadata snapshot are the most current.
- A DM space map metadata refcounting fix that improves both DM thinp
and DM cache metadata"
* tag 'dm-4.4-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm btree: fix bufio buffer leaks in dm_btree_del() error path
dm space map metadata: fix ref counting bug when bootstrapping a new space map
dm thin metadata: fix bug when taking a metadata snapshot
dm thin metadata: fix bug in dm_thin_remove_range()
dm btree: fix leak of bufio-backed block in btree_split_sibling error path
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse fixes from Miklos Szeredi:
"Two bugfixes, both bound for -stable"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: break infinite loop in fuse_fill_write_pages()
cuse: fix memory leak
|
|
Pull drm fixes from Dave Airlie:
"Not too much this time.
- One nouveau workaround extended to a few more GPUs
- Some amdgpu big endian fixes, and a regression fixer
- Some vmwgfx fixes
- One ttm locking fix
- One vgaarb fix"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
vgaarb: fix signal handling in vga_get()
radeon: Fix VCE IB test on Big-Endian systems
radeon: Fix VCE ring test for Big-Endian systems
radeon/cik: Fix GFX IB test on Big-Endian
drm/amdgpu: fix the lost duplicates checking
drm/nouveau/pmu: remove whitelist for PGOB-exit WAR, enable by default
drm/vmwgfx: Implement the cursor_set2 callback v2
drm/vmwgfx: fix a warning message
drm/ttm: Fixed a read/write lock imbalance
|
|
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Alban Bedel <albeu@free.fr>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The pinctrl of rk3228 is much the same as rk3288's, but
without pmu.
Signed-off-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In paging_init, we allocate the zero page, memset it to zero and then
point TTBR0 to it in order to avoid speculative fetches through the
identity mapping.
In order to guarantee that the freshly zeroed page is indeed visible to
the page table walker, we need to execute a dsb instruction prior to
writing the TTBR.
Cc: <stable@vger.kernel.org> # v3.14+, for older kernels need to drop the 'ishst'
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
It's not immediately obvious which hardware errata are worked around in
the Linux kernel for an arbitrary kernel tree, so add a file to keep
track of what we're working around.
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
We drop __cpu_setup in .text.init, which ends up being part of .text.
The .text.init section was a legacy section name which has been unused
elsewhere for a long time.
The ".text.init" name is misleading if read as a synonym for
".init.text". Any CPU may execute __cpu_setup before turning the MMU on,
so it should simply live in .text.
Remove the pointless section assignment. This will leave __cpu_setup in
the .text section.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
External inputs to the vgic from time to time need to poke into the
state of a virtual interrupt, the prime example is the architected timer
code.
Since the IRQ's active state can be represented in two places; the LR or
the distributor, we first loop over the LRs but if not active in the LRs
we just return if *any* IRQ is active on the VCPU in question.
This is of course bogus, as we should check if the specific IRQ in
quesiton is active on the distributor instead.
Reported-by: Eric Auger <eric.auger@linaro.org>
Acked-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Knights Landing does not come with register that could be used to fetch
DIMM width. However the value is fixed for this architecture so it can
be hardcoded.
Signed-off-by: Hubert Chrzaniuk <hubert.chrzaniuk@intel.com>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: lukasz.anaczkowski@intel.com
Link: http://lkml.kernel.org/r/1449840082-18673-1-git-send-email-hubert.chrzaniuk@intel.com
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
Hide the EDAC workqueue pointer in a separate compilation unit and add
accessors for the workqueue manipulations needed.
Remove edac_pci_reset_delay_period() which wasn't used by anything. It
seems it got added without a user with
91b99041c1d5 ("drivers/edac: updated PCI monitoring")
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
They're not used anywhere else.
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
It cannot fail now. We either load EDAC core after having successfully
initialized edac_subsys or we don't.
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
... and use the accessor instead.
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
This was really dumb - reference counting for the main EDAC sysfs
object. While we could've simply registered it as the first thing in the
module init path and then hand it around to what needs it.
Do that and rip out all the code around it, thus simplifying the whole
handling significantly.
Move the edac_subsys node back to edac_module.c.
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
EDAC workqueue destruction is really fragile. We cancel delayed work
but if it is still running and requeues itself, we still go ahead and
destroy the workqueue and the queued work explodes when workqueue core
attempts to run it.
Make the destruction more robust by switching op_state to offline so
that requeuing stops. Cancel any pending work *synchronously* too.
EDAC i7core: Driver loaded.
general protection fault: 0000 [#1] SMP
CPU 12
Modules linked in:
Supported: Yes
Pid: 0, comm: kworker/0:1 Tainted: G IE 3.0.101-0-default #1 HP ProLiant DL380 G7
RIP: 0010:[<ffffffff8107dcd7>] [<ffffffff8107dcd7>] __queue_work+0x17/0x3f0
< ... regs ...>
Process kworker/0:1 (pid: 0, threadinfo ffff88019def6000, task ffff88019def4600)
Stack:
...
Call Trace:
call_timer_fn
run_timer_softirq
__do_softirq
call_softirq
do_softirq
irq_exit
smp_apic_timer_interrupt
apic_timer_interrupt
intel_idle
cpuidle_idle_call
cpu_idle
Code: ...
RIP __queue_work
RSP <...>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: <stable@vger.kernel.org>
|
|
I get the splat below when modprobing/rmmoding EDAC drivers. It happens
because bus->name is invalid after bus_unregister() has run. The Code: section
below corresponds to:
.loc 1 1108 0
movq 672(%rbx), %rax # mci_1(D)->bus, mci_1(D)->bus
.loc 1 1109 0
popq %rbx #
.loc 1 1108 0
movq (%rax), %rdi # _7->name,
jmp kfree #
and %rax has some funky stuff 2030203020312030 which looks a lot like
something walked over it.
Fix that by saving the name ptr before doing stuff to string it points to.
general protection fault: 0000 [#1] SMP
Modules linked in: ...
CPU: 4 PID: 10318 Comm: modprobe Tainted: G I EN 3.12.51-11-default+ #48
Hardware name: HP ProLiant DL380 G7, BIOS P67 05/05/2011
task: ffff880311320280 ti: ffff88030da3e000 task.ti: ffff88030da3e000
RIP: 0010:[<ffffffffa019da92>] [<ffffffffa019da92>] edac_unregister_sysfs+0x22/0x30 [edac_core]
RSP: 0018:ffff88030da3fe28 EFLAGS: 00010292
RAX: 2030203020312030 RBX: ffff880311b4e000 RCX: 000000000000095c
RDX: 0000000000000001 RSI: ffff880327bb9600 RDI: 0000000000000286
RBP: ffff880311b4e750 R08: 0000000000000000 R09: ffffffff81296110
R10: 0000000000000400 R11: 0000000000000000 R12: ffff88030ba1ac68
R13: 0000000000000001 R14: 00000000011b02f0 R15: 0000000000000000
FS: 00007fc9bf8f5700(0000) GS:ffff8801a7c40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 0000000000403c90 CR3: 000000019ebdf000 CR4: 00000000000007e0
Stack:
Call Trace:
i7core_unregister_mci.isra.9
i7core_remove
pci_device_remove
__device_release_driver
driver_detach
bus_remove_driver
pci_unregister_driver
i7core_exit
SyS_delete_module
system_call_fastpath
0x7fc9bf426536
Code: 2e 0f 1f 84 00 00 00 00 00 66 66 66 66 90 53 48 89 fb e8 52 2a 1f e1 48 8b bb a0 02 00 00 e8 46 59 1f e1 48 8b 83 a0 02 00 00 5b <48> 8b 38 e9 26 9a fe e0 66 0f 1f 44 00 00 66 66 66 66 90 48 8b
RIP [<ffffffffa019da92>] edac_unregister_sysfs+0x22/0x30 [edac_core]
RSP <ffff88030da3fe28>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: <stable@vger.kernel.org> # v3.6..
Fixes: 7a623c039075 ("edac: rewrite the sysfs code to use struct device")
|
|
Originally the mpc85xx-pci-edac driver bound directly to the PCI
controller node.
Commit
905e75c46dba ("powerpc/fsl-pci: Unify pci/pcie initialization code")
turned the PCI controller code into a platform device. Since we can't
have two drivers binding to the same device, the EDAC code was changed
to be called into as a library-style submodule. However, this doesn't
work if the EDAC driver is built as a module.
Commit
8d8fcba6d1ea ("EDAC: Rip out the edac_subsys reference counting")
exposed another problem with this approach -- mpc85xx_pci_err_probe()
was being called in the same early boot phase that the PCI controller
is initialized, rather than in the device_initcall phase that the EDAC
layer expects. This caused a crash on boot.
To fix this, the PCI controller code now creates a child platform device
specifically for EDAC, which the mpc85xx-pci-edac driver binds to.
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Daniel Axtens <dja@axtens.net>
Cc: Doug Thompson <dougthompson@xmission.com>
Cc: Jia Hongtao <B38951@freescale.com>
Cc: Jiri Kosina <jkosina@suse.com>
Cc: Kim Phillips <kim.phillips@freescale.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Rob Herring <robh@kernel.org>
Link: http://lkml.kernel.org/r/1449774432-18593-1-git-send-email-scottwood@freescale.com
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
Currently the BUG_ON() checks do not give enough information about the
PTEs being set. This patch changes BUG_ON to WARN_ONCE and dumps the
values of the old and new PTEs. In addition, the checks are only made if
the new PTE entry is valid.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Ming Lei <tom.leiming@gmail.com>
Cc: Will Deacon <will.deacon@arm.com>
|
|
This file does not contain any modular related function calls. So get
rid of module.h since it drags in a lot of other headers and adds to
the preprocessing load. It does export some symbols though, so we'll
need to ensure it has export.h present instead.
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-crypto@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Fix i386-randconfig-x004-12092241.
PCI_IOV needs to be selected when VFs are enabled
Reported-by: <fengguang.wu@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When many threads submit multiple requests they get blocked until all
responses are processed, which prevents them from submitting more requests
even though there is space on the rings.
To fix this we need to decrement the inflight counter early to in the callback.
Signed-off-by: Harvijay Saini <harvijayx.saini@intel.com>
Signed-off-by: Tadeusz Struk <tadeusz.struk@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Fix numerous spelling error in include/crypto/akcipher.h
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Linux on Vybrid used several different L2 latencies so far, none
of them seem to be the right ones. According to the application note
AN4947 ("Understanding Vybrid Architecture"), the tag portion runs
on CPU clock and is inside the L2 cache controller, whereas the data
portion is stored in the external SRAM running on platform clock.
Hence it is likely that the correct value requires a higher data
latency then tag latency.
These are the values which have been used so far:
- The mainline values:
arm,data-latency = <1 1 1>;
arm,tag-latency = <2 2 2>;
Those values have lead to problems on higher clocks. They look
like a poor translation from the reset values (missing +1 offset
and a mix up between tag/latency values).
- The Linux 3.0 (SoC vendor BSP) values (converted to DT notation):
arm,data-latency = <4 2 3>
arm,tag-latency = <4 2 3>
The cache initialization function along with the value matches the
i.MX6 code from the same kernel, so it seems that those values have
just been copied.
- The Colibri values:
arm,data-latency = <2 1 2>;
arm,tag-latency = <3 2 3>;
Those were a mix between the values of the Linux 3.0 based BSP and
the mainline values above.
- The SoC Reset values (converted to DT notation):
arm,data-latency = <3 3 3>;
arm,tag-latency = <2 2 2>;
So far there is no official statement on what the correct values are.
See also the related Freescale community thread:
https://community.freescale.com/message/579785#579785
For now, the reset values seem to be the best bet. Remove all other
"bogus" values and use the reset value on vf610.dtsi level.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Cc: <stable@vger.kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There are so many test cases use stack allocated 'struct machine'.
Including:
test__hists_link
test__hists_filter
test__mmap_thread_lookup
test__thread_mg_share
test__hists_output
test__hists_cumulate
Also, in non-test code (for example, machine__new_host()) there are
code use 'malloc()' to alloc struct machine.
These are dangerous operations, cause some tests fail or hung in
machines__exit(). For example, in
machines__exit ->
machine__destroy_kernel_maps ->
map_groups__remove ->
maps__remove ->
pthread_rwlock_wrlock
a incorrectly initialized lock causes unintended behavior.
This patch memset(0) that structure in machine__init() to ensure all
fields in 'struct machine' are initialized to zero.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1449541544-67621-17-git-send-email-wangnan0@huawei.com
[ Use memset, see 'man bzero' ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Useful for getting stack traces for hardware breakpoint events.
Test result:
Before this patch:
# ~/perf record -g -e mem:0x600980 ./sample
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.011 MB perf.data (12 samples) ]
# ~/perf script
# ~/perf script -F comm,tid,pid,time,event,ip,sym,dso
sample 22520/22520 97457.836294: mem:0x600980:
5a4ad8 __clear_user (/lib/modules/4.3.0-rc4+/build/vmlinux)
...
3f41ba sys_execve (/lib/modules/4.3.0-rc4+/build/vmlinux)
979395 return_from_execve (/lib/modules/4.3.0-rc4+/build/vmlinux)
7f1b59719cf7 [unknown] ([unknown])
sample 22520/22520 97457.836648: mem:0x600980:
532 main (/home/w00229757/DataBreakpoints/sample)
21bd5 __libc_start_main (/tmp/oxygen_root-root/lib64/libc-2.18.so)
...
After this patch:
# ~/perf script
sample 22520 97457.836294: mem:0x600980:
5a4ad8 __clear_user (/lib/modules/4.3.0-rc4+/build/vmlinux)
...
3f41ba sys_execve (/lib/modules/4.3.0-rc4+/build/vmlinux)
979395 return_from_execve (/lib/modules/4.3.0-rc4+/build/vmlinux)
7f1b59719cf7 [unknown] ([unknown])
sample 22520 97457.836648: mem:0x600980:
532 main (/home/w00229757/DataBreakpoints/sample)
21bd5 __libc_start_main (/tmp/oxygen_root-root/lib64/libc-2.18.so)
Committer note:
So, further testing, lets do it for a kernel global variable,
tcp_hashinfo:
# grep -w tcp_hashinfo /proc/kallsyms
ffffffff8202fc00 B tcp_hashinfo
#
Note: allow specifying mem:tcp_hashinfo:
# perf record -g -e mem:0xffffffff81c65ac0 -a
^C[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.790 MB perf.data ]
#
# perf evlist
mem:0xffffffff8202fc00
# perf evlist -v
mem:0xffffffff8202fc00: type: 5, size: 112, { sample_period, sample_freq }: 1, sample_type: IP|TID|TIME|CALLCHAIN|CPU, disabled: 1, inherit: 1, mmap: 1, comm: 1, task: 1, sample_id_all: 1, exclude_guest: 1, mmap2: 1, comm_exec: 1, bp_type: 3, { bp_addr, config1 }: 0xffffffff8202fc00, { bp_len, config2 }: 0x4
#
Then, after this patch:
# perf script
swapper 0 [000] 171036.986988: mem:0xffffffff8202fc00:
8a0fb5 __inet_lookup_established (/lib/modules/4.3.0+/build/vmlinux)
8bc09d tcp_v4_early_demux (/lib/modules/4.3.0+/build/vmlinux)
896def ip_rcv_finish (/lib/modules/4.3.0+/build/vmlinux)
8976c2 ip_rcv (/lib/modules/4.3.0+/build/vmlinux)
855eba __netif_receive_skb_core (/lib/modules/4.3.0+/build/vmlinux)
8565d8 __netif_receive_skb (/lib/modules/4.3.0+/build/vmlinux)
8572a8 process_backlog (/lib/modules/4.3.0+/build/vmlinux)
856b11 net_rx_action (/lib/modules/4.3.0+/build/vmlinux)
2a284b __do_softirq (/lib/modules/4.3.0+/build/vmlinux)
2a2ba3 irq_exit (/lib/modules/4.3.0+/build/vmlinux)
96b7a4 do_IRQ (/lib/modules/4.3.0+/build/vmlinux)
969807 ret_from_intr (/lib/modules/4.3.0+/build/vmlinux)
804c27 cpuidle_enter (/lib/modules/4.3.0+/build/vmlinux)
2ded22 call_cpuidle (/lib/modules/4.3.0+/build/vmlinux)
2defb6 cpu_startup_entry (/lib/modules/4.3.0+/build/vmlinux)
95d5bc rest_init (/lib/modules/4.3.0+/build/vmlinux)
1163ffa start_kernel ([kernel.vmlinux].init.text)
11634d7 x86_64_start_reservations ([kernel.vmlinux].init.text)
1163623 x86_64_start_kernel ([kernel.vmlinux].init.text)
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1449541544-67621-16-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Add hexadecimal u32 to base data type, which is useful for raw output
because raw data is u32 aligned.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Alexei Starovoitov <ast@kernel.org>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1449541544-67621-12-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
minor change, indenting is one tab out.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This patch is derived from
commit 6301566e0b2d ("ath9k: export HW random number generator"),
We evaluated the entropy of the ADC data on QCA9531, QCA9561, QCA955x,
and AR9340, and it has sufficient quality random data (at least 10 bits
and up to 22 bits of min-entropy for a 32-bit value). We conservatively
assume the min-entropy is 10 bits out of 32 bits. Thus, ATH9K_RNG_BUF_SIZE
is set to 320 (u32) i.e., 1.25 kilobytes of data is inserted to fill up
the pool as soon as the entropy counter becomes 896/4096 (set by random.c).
Since ADC was not designed to be a dedicated HW RNG, we do not want to bind
it to /dev/hwrng framework directly. This patch feeds the entropy directly
from the WiFi driver to the input pool. The ADC register output is only
used as a seed for the Linux entropy pool. No conditioning is needed,
since all the conditioning is performed by the pool itself.
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
When rx stopped, AR_RX_FILTER should be cleared, but in
ath9k_hw_setrxfilter(), ATH9K_RX_FILTER_CONTROL_WRAPPER will always
be set for ar9462/ar9565.
Fix this by moving the code in ath9k_hw_setrxfilter() to
ath_calcrxfilter().
Signed-off-by: Miaoqing Pan <miaoqing@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This gives a user a chance to know why a firmware load
is failing.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
My previous patch incorrectly reported the antenna
for 2x2 devices. It should be a mask instead of
a numeric count. This patch fixes that.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The maximum chunks used by the function is
(SPI_AGGR_BUFFER_SIZE / WSPI_MAX_CHUNK_SIZE + 1).
The original commands array had space for
(SPI_AGGR_BUFFER_SIZE / WSPI_MAX_CHUNK_SIZE) commands.
When the last chunk is used (len > 4 * WSPI_MAX_CHUNK_SIZE), the last
command is stored outside the bounds of the commands array.
Oops 5 (page fault) is generated during current wl1271 firmware load
attempt:
root@debian-armhf:~# ifconfig wlan0 up
[ 294.312399] Unable to handle kernel paging request at virtual address
00203fc4
[ 294.320173] pgd = de528000
[ 294.323028] [00203fc4] *pgd=00000000
[ 294.326916] Internal error: Oops: 5 [#1] SMP ARM
[ 294.331789] Modules linked in: bnep rfcomm bluetooth ipv6 arc4 wl12xx
wlcore mac80211 musb_dsps cfg80211 musb_hdrc usbcore usb_common
wlcore_spi omap_rng rng_core musb_am335x omap_wdt cpufreq_dt thermal_sys
hwmon
[ 294.351838] CPU: 0 PID: 1827 Comm: ifconfig Not tainted
4.2.0-00002-g3e9ad27-dirty #78
[ 294.360154] Hardware name: Generic AM33XX (Flattened Device Tree)
[ 294.366557] task: dc9d6d40 ti: de550000 task.ti: de550000
[ 294.372236] PC is at __spi_validate+0xa8/0x2ac
[ 294.376902] LR is at __spi_sync+0x78/0x210
[ 294.381200] pc : [<c049c760>] lr : [<c049ebe0>] psr: 60000013
[ 294.381200] sp : de551998 ip : de5519d8 fp : 00200000
[ 294.393242] r10: de551c8c r9 : de5519d8 r8 : de3a9000
[ 294.398730] r7 : de3a9258 r6 : de3a9400 r5 : de551a48 r4 :
00203fbc
[ 294.405577] r3 : 00000000 r2 : 00000000 r1 : 00000000 r0 :
de3a9000
[ 294.412420] Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM
Segment user
[ 294.419918] Control: 10c5387d Table: 9e528019 DAC: 00000015
[ 294.425954] Process ifconfig (pid: 1827, stack limit = 0xde550218)
[ 294.432437] Stack: (0xde551998 to 0xde552000)
...
[ 294.883613] [<c049c760>] (__spi_validate) from [<c049ebe0>]
(__spi_sync+0x78/0x210)
[ 294.891670] [<c049ebe0>] (__spi_sync) from [<bf036598>]
(wl12xx_spi_raw_write+0xfc/0x148 [wlcore_spi])
[ 294.901661] [<bf036598>] (wl12xx_spi_raw_write [wlcore_spi]) from
[<bf21c694>] (wlcore_boot_upload_firmware+0x1ec/0x458 [wlcore])
[ 294.914038] [<bf21c694>] (wlcore_boot_upload_firmware [wlcore]) from
[<bf24532c>] (wl12xx_boot+0xc10/0xfac [wl12xx])
[ 294.925161] [<bf24532c>] (wl12xx_boot [wl12xx]) from [<bf20d5cc>]
(wl1271_op_add_interface+0x5b0/0x910 [wlcore])
[ 294.936364] [<bf20d5cc>] (wl1271_op_add_interface [wlcore]) from
[<bf15c4ac>] (ieee80211_do_open+0x44c/0xf7c [mac80211])
[ 294.947963] [<bf15c4ac>] (ieee80211_do_open [mac80211]) from
[<c0537978>] (__dev_open+0xa8/0x110)
[ 294.957307] [<c0537978>] (__dev_open) from [<c0537bf8>]
(__dev_change_flags+0x88/0x148)
[ 294.965713] [<c0537bf8>] (__dev_change_flags) from [<c0537cd0>]
(dev_change_flags+0x18/0x48)
[ 294.974576] [<c0537cd0>] (dev_change_flags) from [<c05a55a0>]
(devinet_ioctl+0x6b4/0x7d0)
[ 294.983191] [<c05a55a0>] (devinet_ioctl) from [<c0517040>]
(sock_ioctl+0x1e4/0x2bc)
[ 294.991244] [<c0517040>] (sock_ioctl) from [<c017d378>]
(do_vfs_ioctl+0x420/0x6b0)
[ 294.999208] [<c017d378>] (do_vfs_ioctl) from [<c017d674>]
(SyS_ioctl+0x6c/0x7c)
[ 295.006880] [<c017d674>] (SyS_ioctl) from [<c000f4c0>]
(ret_fast_syscall+0x0/0x54)
[ 295.014835] Code: e1550004 e2444034 0a00007d e5953018 (e5942008)
[ 295.021544] ---[ end trace 66ed188198f4e24e ]---
Signed-off-by: Uri Mashiach <uri.mashiach@compulab.co.il>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: stable@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Namhyung Kim pointed out a potential problem in original code that it
fetches names of maps from section header string table, which is used
to store section names.
Original code doesn't cause error because of a LLVM behavior that, it
combines shstrtab into strtab. For example:
$ echo 'int func() {return 0;}' | x86_64-oe-linux-clang -x c -o temp.o -c -
$ readelf -h ./temp.o
ELF Header:
Magic: 7f 45 4c 46 02 01 01 03 00 00 00 00 00 00 00 00
...
Section header string table index: 1
$ readelf -S ./temp.o
There are 10 section headers, starting at offset 0x288:
Section Headers:
[Nr] Name Type Address Offset
Size EntSize Flags Link Info Align
[ 0] NULL 0000000000000000 00000000
0000000000000000 0000000000000000 0 0 0
[ 1] .strtab STRTAB 0000000000000000 00000230
0000000000000051 0000000000000000 0 0 1
...
$ readelf -p .strtab ./temp.o
String dump of section '.strtab':
[ 1] .text
[ 7] .comment
[ 10] .bss
[ 15] .note.GNU-stack
[ 25] .rela.eh_frame
[ 34] func
[ 39] .strtab
[ 41] .symtab
[ 49] .data
[ 4f] -
$ readelf -p .shstrtab ./temp.o
readelf: Warning: Section '.shstrtab' was not dumped because it does not exist!
Where, 'section header string table index' points to '.strtab', and
symbol names are also stored there.
However, in case of gcc:
$ echo 'int func() {return 0;}' | gcc -x c -o temp.o -c -
$ readelf -p .shstrtab ./temp.o
String dump of section '.shstrtab':
[ 1] .symtab
[ 9] .strtab
[ 11] .shstrtab
[ 1b] .text
[ 21] .data
[ 27] .bss
[ 2c] .comment
[ 35] .note.GNU-stack
[ 45] .rela.eh_frame
$ readelf -p .strtab ./temp.o
String dump of section '.strtab':
[ 1] func
They are separated sections.
Although original code doesn't cause error, we'd better use canonical
method for fetching symbol names to avoid potential behavior changing.
This patch learns from readelf's code, fetches string from sh_link
of .symbol section.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Reported-and-Acked-by: Namhyung Kim <namhyung@kernel.org>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1449541544-67621-3-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
All interface layer related to scheduled scan are moved in
fwil_types.h
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The pcie suspend and resume routines contain some error prints,
which should have been debug prints.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Got a hint on IRC that a 43242 dongle for LG smart TV's works with
brcmfmac:
> Hello - I recently got a LG AN-WF500 wireless dongle for LG's SmartTVs.
> From the information I gathered it uses a Broadcom chipset BCM43242.
> The device should have been supported by brcmfmac kernel driver if it used
> USB IDs 0a5c:bd1f.
> My device however identifies itself as "ID 043e:3101 LG Electronics USA, Inc.".
> I then tried adding the USB ID to the driver with
> "echo "043e 3101" > /sys/bus/usb/drivers/brcmfmac/new_id" and it just works.
> The kernel provides the following information.
> [15958.851291] usb 3-1.1.3: new high-speed USB device number 53 using ehci-pci
> [15958.946723] usb 3-1.1.3: New USB device found, idVendor=043e, idProduct=3101
> [15958.946728] usb 3-1.1.3: New USB device strings: Mfr=1, Product=4, SerialNumber=3
> [15958.946731] usb 3-1.1.3: Product: Composite Wireless Adapter
> [15958.946733] usb 3-1.1.3: Manufacturer: Broadcom
> [15958.946735] usb 3-1.1.3: SerialNumber: 28458
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
brcmf_msgbuf_ioctl_resp_wake() seems to be missing a memory barrier
which might cause the waker to not notice the waiter and miss sending a
wake_up as in the following figure.
brcmf_msgbuf_ioctl_resp_wake brcmf_msgbuf_ioctl_resp_wait
------------------------------------------------------------------------
if (waitqueue_active(&msgbuf->ioctl_resp_wait))
/* The CPU might reorder the test for
the waitqueue up here, before
prior writes complete */
/* wait_event_timeout */
/* __wait_event_timeout */
/* ___wait_event */
prepare_to_wait_event(&wq, &__wait,
state);
if (msgbuf->ctl_completed)
...
msgbuf->ctl_completed = true;
schedule_timeout(__ret))
------------------------------------------------------------------------
There are three other place in drivers/net/wireless/brcm80211/brcmfmac/
which have similar code. The attached patch removes the call to
waitqueue_active() leaving just wake_up() behind. This fixes the
problem because the call to spin_lock_irqsave() in wake_up() will be an
ACQUIRE operation.
I found this issue when I was looking through the linux source code
for places calling waitqueue_active() before wake_up*(), but without
preceding memory barriers, after sending a patch to fix a similar
issue in drivers/tty/n_tty.c (Details about the original issue can be
found here: https://lkml.org/lkml/2015/9/28/849).
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Kosuke Tatsukawa <tatsu@ab.jp.nec.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
IBSS got broken over time. Disconnect events should not be given
for IBSS mode and connect events for IBSS need to have channel
information.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The interface combinations are intended for use-case in which the driver
handles multiple interface concurrently. This means that the combinations
do not need to be checked when there is only a single interface active.
Reviewed-by: Hante Meuleman <meuleman@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
