| Age | Commit message (Collapse) | Author |
|---|
|
This patches fixes few issues in mv88e6390x_port_set_cmode().
1. When entering the function the old cmode may be 0, in this case
mv88e6390x_serdes_get_lane() returns -ENODEV. As result we bail
out and have no chance to set a new mode. Therefore deal properly
with -ENODEV.
2. Once we have disabled power and irq, let's set the cached cmode to 0.
This reflects the actual status and is cleaner if we bail out with an
error in the following function calls.
3. The cached cmode is used by mv88e6390x_serdes_get_lane(),
mv88e6390_serdes_power_lane() and mv88e6390_serdes_irq_enable().
Currently we set the cached mode to the new one at the very end of
the function only, means until then we use the old one what may be
wrong.
4. When calling mv88e6390_serdes_irq_enable() we use the lane value
belonging to the old cmode. Get the lane belonging to the new cmode
before calling this function.
It's hard to provide a good "Fixes" tag because quite a few smaller
changes have been done to the code in question recently.
Fixes: d235c48b40d3 ("net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On the D3 SoC the LVDS PHY must be enabled in the same register write
that enables the LVDS output. Skip writing the LVEN bit independently
on that platform, it will be set by the write that sets LVRES.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
|
|
The D3 and E3 SoCs have different pixel clock frequency limits for the
LVDS encoder than the other SoCs in the Gen3 family. Adjust the mode
fixup implementation accordingly.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
|
|
The rcar_du_crtc functions have a heavy reliance on the rcar_du_group
structure, in many cases just to access the DU device context.
To better separate the groups out of the CRTC handling code, give the
rcar_du_crtc its own pointer to the device and remove the indirection
through the group pointers.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
The PLL parameters are computed by looping over the range of acceptable
M, N and E values, and selecting the combination that produces the
output frequency closest to the target. The internal frequency
constraints are taken into account by restricting the tested values for
the PLL parameters, reducing the search space. The target frequency,
however, is only taken into account when computing the post-PLL divider,
which can result in a 0 value for the divider when the PLL output
frequency being tested is lower than half of the target frequency.
Subsequent loops will produce a better set of PLL parameters, but for
some of the iterations this can result in a division by 0.
Fix it by clamping the divider value. We could instead restrict the E
values being tested in the inner loop, but that would require additional
calculation that would likely be less efficient as the E parameter can
only take three different values.
Fixes: c25c01361199 ("drm: rcar-du: lvds: D3/E3 support")
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
|
|
drm_framebuffer.h makes use of a pointer to struct drm_format_info but
doesn't include drm_fourcc.h (neither directly nor indirectly).
Forward-declare the structure.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
|
|
The CRTC suspend and resume functions have been replaced, but the
prototypes were not removed.
Remove the redundant definitions.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
The rcar_du_crtc_mode_valid() and rcar_du_crtc_get_crc_sources()
functions are accessed only through a function pointer table.
Convert the function definitions to be static to the module.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
The drm_crtc_state documentation contains a subtle misspelling of the
word subtle. Correct it.
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
|
|
The R-Car DU driver assumes that a bridge is always connected to the DU
output. This is valid for the LVDS and HDMI outputs, but the DPAD
outputs can be connected directly to a panel, in which case no bridge is
available.
To support this use case, detect whether the entities connected to the
DU DPAD outputs are encoders or panels based on the number of ports of
their DT node, and retrieve the corresponding type of DRM objects. For
panels, additionally create panel bridge instances.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Tested-by: Kevin Key <kevin.key@gentex.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
|
|
No need to update current profile mode if the new profile mode
does not take effect in fact.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Kent Russell <kent.russell@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Currently only top pipe gets output tf programmed. This change
makes all odm head pipes get output tf programmed.
Signed-off-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nikola Cornij <Nikola.Cornij@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Create a functions to return swizzle types for dml
Signed-off-by: Joshua Aberback <joshua.aberback@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Reviewed-by: Nevenko Stupar <Nevenko.Stupar@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Aric Cyr <Aric.Cyr@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
pass SDP splitting when setting stream attributes for future use
Signed-off-by: Nikola Cornij <nikola.cornij@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Create dccg_init and init_clocks for future use
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
set_display_requirement, dcn1_pplib_apply_display_requirements
are no longer used and should be removed.
Signed-off-by: Fatemeh Darbehani <fatemeh.darbehani@amd.com>
Reviewed-by: Hersen Wu <hersenxs.wu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[WHY]
The resource constructor currently needs num_virtual_links from
init_data but will need access to other items provided by DM.
[HOW]
Pass init_data into DCN create_resource_pool functions.
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Hersen Wu <hersenxs.wu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
When you have a SST branch device the driver, Even no sink device connected,
it also send HPD with a valid EDID. Driver will config it to DP sink.
Therefore, there're two displays in display setting.
DPCD 0x05, DFP_PRESENT = 1 (branch device),
DFP_TYPE = 00 (Display Port)
[How]
Driver determine DPCD 0x05 DFP_PRESENT = 1(branch) as an active dongle
And check DFP count.
Signed-off-by: Hugo Hu <hugo.hu@amd.com>
Reviewed-by: Hugo Hu <Hugo.Hu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
program default output gamma if no user specific gamma
parameters passed.
Signed-off-by: hersen wu <hersenxs.wu@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[why]
existing logic finds "first free pipe from 5 -> 0" to split
this will cause certain sequences to require DC to move
an MPCC from one tree to another, which is unsupported
this leads to blackscreen
to mitigate this problem, we will always try to acquire the
"preferred" pipe, and each pipe has a unique preferred pipe
this means we avoid most of the scenarios where
pipe splitting leads to moving MPCC from one tree
to another
Signed-off-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Tony Cheng <Tony.Cheng@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Instead of skipping the root PD while processing the relocated list just never
put it on the list in the first place.
This avoids walking the list all together when the root PD is the only entry
and so also avoids trying to submit a zero sized IB to the SDMA.
Signed-off-by: Christian König <christian.koenig@amd.com>
Tested-by: Michel Dänzer <michel.daenzer@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It is redundant with the job pointer.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Clean that up further and also fix another case where the BO
wasn't kmapped for CPU based updates.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Driver vote low to high pstate switch whenever there is an outstanding
XGMI mapping request. Driver vote high to low pstate when all the
outstanding XGMI mapping is terminated.
Signed-off-by: shaoyunl <shaoyun.liu@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
And remove the existing code when it is unused.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
As the cleanup jobs performed in pre_fini may still need these
buffers. NULL pointer dereference will be triggered without them.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Large piece of codes share one error prompt. That
is not friendly for debugging.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The error return value should be correctly reflected.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
"error" was not correctly spelled.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
there is ras_control node which can do its job.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Add helpes to transalte the two enums. And it will catch bugs
easily.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
better to use macro.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
ras context might be NULL, so move con->h_data after check !con
also fix sizeof wrong type while at it.
Signed-off-by: xinhui pan <xinhui.pan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
VBIOS will not post pixel rate > 340MHz.
If driver set pixel rate > 340MHz and do restart bottom, VBIOS can't
post HDMI monitor due to monitor is stay in HDMI2.0 state.
[How]
Program Scrambling_Enable and TMDS_Bit_Clock_Ratio when disable stream.
Signed-off-by: Paul Hsieh <paul.hsieh@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Acked-by: Harry Wentland <Harry.Wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
If DAL requires to force MCLK high, the FCLK will be
forced to high also.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Avoid left shift overflow.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It's OK to have this feature bit with old SMU firmwares.
But the feature should be disabled on them.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
use pcie_bandwidth_available to get real link state
to update pcie table.
v2: fix incorrect initialized return value
v3: expand the fetching method about the link width to all asics.
Signed-off-by: Chengming Gui <Jack.Gui@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
No change to functionality. Simply make transport event messages a little
clearer, and rework CRQ format enums such that we have separate enums for
INIT messages and XPORT events.
[mkp: typo]
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Status and error codes are returned in big endian from the VIOS. The values
are translated into a human readable format when logged, but the values are
also logged. This patch byte swaps those values so that they are consistent
between BE and LE platforms.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The VIOS uses the SCSI_ERROR class to report PRLI failures. These errors
are indicated with the combination of a IBMVFC_FC_SCSI_ERROR return status
and 0x8000 error code. Add these codes to cmd_status[] with appropriate
human readable error message.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The text of messages logged with ibmvfc_log_error() always contain the term
"failed". In the case of cancelled commands during EH they are reported
back by the VIOS using error codes. This can be confusing to somebody
looking at these log messages as to whether a command was successfully
cancelled. The following real log message for example it is unclear if the
transaction was actaully cancelled.
<6>sd 0:0:1:1: Cancelling outstanding commands.
<3>sd 0:0:1:1: [sde] Command (28) failed: transaction cancelled (2:6) flags: 0 fcp_rsp: 0, resid=0, scsi_status: 0
Remove prefixing of "failed" to all error logged messages. The
ibmvfc_log_error() function translates the returned error/status codes to a
human readable message already.
Signed-off-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
If an incoming ELS of type RSCN contains more than one element, zfcp
suboptimally causes repeated erp trigger NOP trace records for each
previously failed port. These could be ports that went away. It loops over
each RSCN element, and for each of those in an inner loop over all
zfcp_ports.
The trigger to recover failed ports should be just the reception of some
RSCN, no matter how many elements it has. So we can loop over failed ports
separately, and only then loop over each RSCN element to handle the
non-failed ports.
The call chain was:
zfcp_fc_incoming_rscn
for (i = 1; i < no_entries; i++)
_zfcp_fc_incoming_rscn
list_for_each_entry(port, &adapter->port_list, list)
if (masked port->d_id match) zfcp_fc_test_link
if (!port->d_id) zfcp_erp_port_reopen "fcrscn1" <===
In order the reduce the "flooding" of the REC trace area in such cases, we
factor out handling the failed ports to be outside of the entries loop:
zfcp_fc_incoming_rscn
if (no_entries > 1) <===
list_for_each_entry(port, &adapter->port_list, list) <===
if (!port->d_id) zfcp_erp_port_reopen "fcrscn1" <===
for (i = 1; i < no_entries; i++)
_zfcp_fc_incoming_rscn
list_for_each_entry(port, &adapter->port_list, list)
if (masked port->d_id match) zfcp_fc_test_link
Abbreviated example trace records before this code change:
Tag : fcrscn1
WWPN : 0x500507630310d327
ERP want : 0x02
ERP need : 0x02
Tag : fcrscn1
WWPN : 0x500507630310d327
ERP want : 0x02
ERP need : 0x00 NOP => superfluous trace record
The last trace entry repeats if there are more than 2 RSCN elements.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Suppose more than one non-NPIV FCP device is active on the same channel.
Send I/O to storage and have some of the pending I/O run into a SCSI
command timeout, e.g. due to bit errors on the fibre. Now the error
situation stops. However, we saw FCP requests continue to timeout in the
channel. The abort will be successful, but the subsequent TUR fails.
Scsi_eh starts. The LUN reset fails. The target reset fails. The host
reset only did an FCP device recovery. However, for non-NPIV FCP devices,
this does not close and reopen ports on the SAN-side if other non-NPIV FCP
device(s) share the same open ports.
In order to resolve the continuing FCP request timeouts, we need to
explicitly close and reopen ports on the SAN-side.
This was missing since the beginning of zfcp in v2.6.0 history commit
ea127f975424 ("[PATCH] s390 (7/7): zfcp host adapter.").
Note: The FSF requests for forced port reopen could run into FSF request
timeouts due to other reasons. This would trigger an internal FCP device
recovery. Pending forced port reopen recoveries would get dismissed. So
some ports might not get fully reopened during this host reset handler.
However, subsequent I/O would trigger the above described escalation and
eventually all ports would be forced reopen to resolve any continuing FCP
request timeouts due to earlier bit errors.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: <stable@vger.kernel.org> #3.0+
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
An already deleted SCSI device can exist on the Scsi_Host and remain there
because something still holds a reference. A new SCSI device with the same
H:C:T:L and FCP device, target port WWPN, and FCP LUN can be created. When
we try to unblock an rport, we still find the deleted SCSI device and
return early because the zfcp_scsi_dev of that SCSI device is not
ZFCP_STATUS_COMMON_UNBLOCKED. Hence we miss to unblock the rport, even if
the new proper SCSI device would be in good state.
Therefore, skip deleted SCSI devices when iterating the sdevs of the shost.
[cf. __scsi_device_lookup{_by_target}() or scsi_device_get()]
The following abbreviated trace sequence can indicate such problem:
Area : REC
Tag : ersfs_3
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x40000000 not ZFCP_STATUS_COMMON_UNBLOCKED
Ready count : n not incremented yet
Running count : 0x00000000
ERP want : 0x01
ERP need : 0xc1 ZFCP_ERP_ACTION_NONE
Area : REC
Tag : ersfs_3
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x41000000
Ready count : n+1
Running count : 0x00000000
ERP want : 0x01
ERP need : 0x01
...
Area : REC
Level : 4 only with increased trace level
Tag : ertru_l
LUN : 0x4045400300000000
WWPN : 0x50050763031bd327
LUN status : 0x40000000
Request ID : 0x0000000000000000
ERP status : 0x01800000
ERP step : 0x1000
ERP action : 0x01
ERP count : 0x00
NOT followed by a trace record with tag "scpaddy"
for WWPN 0x50050763031bd327.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: 6f2ce1c6af37 ("scsi: zfcp: fix rport unblock race with LUN recovery")
Cc: <stable@vger.kernel.org> #2.6.32+
Reviewed-by: Jens Remus <jremus@linux.ibm.com>
Reviewed-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Commit a83da8a4509d ("scsi: sd: Optimal I/O size should be a multiple
of physical block size") split one conditional into several separate
statements in an effort to provide more accurate warning messages when
a device reports a nonsensical value. However, this reorganization
accidentally dropped the precondition of the reported value being
larger than zero. This lead to a warning getting emitted on devices
that do not report an optimal I/O size at all.
Remain silent if a device does not report an optimal I/O size.
Fixes: a83da8a4509d ("scsi: sd: Optimal I/O size should be a multiple of physical block size")
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: <stable@vger.kernel.org>
Reported-by: Hussam Al-Tayeb <ht990332@gmx.com>
Tested-by: Hussam Al-Tayeb <ht990332@gmx.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The scsi_end_request() function calls scsi_cmd_to_driver() indirectly and
hence needs the disk->private_data pointer. Avoid that that pointer is
cleared before all affected I/O requests have finished. This patch avoids
that the following crash occurs:
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
Call trace:
scsi_mq_uninit_cmd+0x1c/0x30
scsi_end_request+0x7c/0x1b8
scsi_io_completion+0x464/0x668
scsi_finish_command+0xbc/0x160
scsi_eh_flush_done_q+0x10c/0x170
sas_scsi_recover_host+0x84c/0xa98 [libsas]
scsi_error_handler+0x140/0x5b0
kthread+0x100/0x12c
ret_from_fork+0x10/0x18
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ming Lei <ming.lei@redhat.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Jason Yan <yanaijie@huawei.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Reported-by: Jason Yan <yanaijie@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Use dd to test a SCSI device:
1. echo "blocked" >/sys/block/sda/device/state
2. dd if=/dev/sda of=/mnt/t.log bs=1M count=10
3. echo "running" >/sys/block/sda/device/state
dd should finish this work after step 3, but it hangs.
After step2, the call chain is this:
blk_mq_dispatch_rq_list-->scsi_queue_rq-->prep_to_mq
prep_to_mq will return BLK_STS_RESOURCE, and scsi_queue_rq will
transition it to BLK_STS_DEV_RESOURCE which means that driver can
guarantee that IO dispatch will be triggered in future when the
resource is available. Need to follow the rule if we set the device
state to running.
[mkp: tweaked commit description and code comment as suggested by Bart]
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Reviewed-by: Ming Lei <ming.lei@redhat.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
