summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2020-01-16drm/amd/display: store lttpr mode with dpcdabdoulaye berthe
Make sure that lttpr_caps has the mode set to repeater. Signed-off-by: abdoulaye berthe <abdoulaye.berthe@amd.com> Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amd/display: Add double buffering to dcn20 OCSCNoah Abradjian
[Why] When rapidly adjusting colour properties (e.g. brightness), screen tearing was observed. This was due to overwritten values in OCSC registers. In dcn10, this issue had been fixed by implementing double buffering by alternating OCSC modes. [How] Alternate which OCSC registers are used by switching modes each time. This double buffers the CSC writes. Signed-off-by: Noah Abradjian <noah.abradjian@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amd/display: Soft reset DMUIF during DMUB resetNicholas Kazlauskas
[Why] We need to ensure that the DMUIF in MMHUBBUB is also in reset so we aren't generating requests while the DMCUB is in reset. [How] Set DMUIF_SOFT_RESET=1 on reset and DMUIF_SOFT_RESET=0 on reset release. Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amd/display: Read inst_fb data back during DMUB loadingNicholas Kazlauskas
[Why] The inst firmware isn't necessarily fully flushed to framebuffer memory and the DMCUB can hang due to invalid inst being parsed. [How] Like the fix to flush ringbuffer commands before updating the inbox write pointer we need to read back inst memory before writing the CW0 registers. Add a helper to read 64-byte chunks to avoid a large temporary buffer. Read the remaining leftover bytes if the inst_fb isn't fully aligned. Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amd/display: Flush framebuffer data before passing to DMCUBNicholas Kazlauskas
[Why] There's a data race that can occur between when we update the inbox write pointer vs when the memory for the command actually gets flushed from the map to the framebuffer. DMCUB can read stale or partially invalid data when this race occurs. [How] Before updating the write pointer we can read back all pending commands to ensure that we stall for the writes to be flushed to framebuffer. We don't need to worry about choosing HDP vs VM flush with this mechanism. Drop the dmub_srv_cmd_submit() while we're updating this to work correctly since nothing was actually using this API and the caller should be explicit about the API flow here - by doing this on execute we can give some extra time for the flush to finish while preparing other commands. We should try to avoid writing single commands because of this overhead. Signed-off-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amd/display: Adding forgotten hubbub funcMartin Leung
[why] While doing seamless boot I made some changes to dcn2 hubbub functions, missed a link [how] link hubbub1 func to hubbub2 usage. It has already been successfully linked in dcn1 and 3. Signed-off-by: Martin Leung <martin.leung@amd.com> Reviewed-by: Alvin Lee <Alvin.Lee2@amd.com> Acked-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amd/display: Disable secondary link for certain monitorsNikola Cornij
[why] If the specific monitor supports DSC, the secondary link should be disabled, and the other way around, too: if either that monitor or our ASIC doesn't support DSC, the secodary link should be enabled. [how] Add a monitor patch and disable secondary link if that monitor is detected and if ASIC supports DSC, or otherwise enable secondary link. Signed-off-by: Nikola Cornij <nikola.cornij@amd.com> Reviewed-by: Joshua Aberback <Joshua.Aberback@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amd/display: Fix 300Hz Freesync bugAlvin Lee
Needed to reprogram vblank_start in dml properly in order to get the correct dlg params to program VTG. Signed-off-by: Alvin Lee <alvin.lee2@amd.com> Reviewed-by: Martin Leung <Martin.Leung@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amd/display: fix chroma vp wa corner caseEric Yang
[Why] Previous implementation we may have residual chroma address offset if transition from wa enable -> wa disable. [How] Clear address offset cache when viewport updates. Also update the vp size check condition to account for rotation angle Signed-off-by: Eric Yang <Eric.Yang2@amd.com> Reviewed-by: Tony Cheng <Tony.Cheng@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amd/display: 3.2.65Aric Cyr
Signed-off-by: Aric Cyr <aric.cyr@amd.com> Reviewed-by: Aric Cyr <Aric.Cyr@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amd/display: Clear state after exiting fixed active VRR stateAmanda Liu
[why] Upon exiting a fixed active VRR state, the state isn't cleared. This leads to the variable VRR range to be calculated incorrectly. [how] Set fixed active state to false when updating vrr params Signed-off-by: Amanda Liu <amanda.liu@amd.com> Reviewed-by: Anthony Koo <Anthony.Koo@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Acked-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amd/include: Add OCSC registersRodrigo Siqueira
Add registers for handling Post Gamma Color Blending (OCSC), which is useful for conversion from RGB->YUV for HDMI. Reviewed-by: Leo Li <sunpeng.li@amd.com> Acked-by: Harry Wentland <harry.wentland@amd.com> Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/scheduler: fix documentation by replacing rq_list with sched_listNirmoy Das
This also replaces old artifacts with a correct one in drm_sched_entity_init() declaration Signed-off-by: Nirmoy Das <nirmoy.das@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu: add arcturus to gpu recovery check code pathHawking Zhang
support check if dirver should try gpu recovery for arcturus Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Reviewed-by: Guchun Chen <guchun.chen@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu: check if driver should try recovery in ras recovery pathHawking Zhang
To allow the flexibilty for user to disable gpu recovery in RAS recovery path by module parameter amdgpu_gpu_recovery Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com> Reviewed-by: Guchun Chen <guchun.chen@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amd/powerplay: a quick fix for the deadlock issue belowEvan Quan
NFO: task ocltst:2028 blocked for more than 120 seconds. Tainted: G OE 5.0.0-37-generic #40~18.04.1-Ubuntu echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. cltst D 0 2028 2026 0x00000000 all Trace: __schedule+0x2c0/0x870 schedule+0x2c/0x70 schedule_preempt_disabled+0xe/0x10 __mutex_lock.isra.9+0x26d/0x4e0 __mutex_lock_slowpath+0x13/0x20 ? __mutex_lock_slowpath+0x13/0x20 mutex_lock+0x2f/0x40 amdgpu_dpm_set_powergating_by_smu+0x64/0xe0 [amdgpu] gfx_v8_0_enable_gfx_static_mg_power_gating+0x3c/0x70 [amdgpu] gfx_v8_0_set_powergating_state+0x66/0x260 [amdgpu] amdgpu_device_ip_set_powergating_state+0x62/0xb0 [amdgpu] pp_dpm_force_performance_level+0xe7/0x100 [amdgpu] amdgpu_set_dpm_forced_performance_level+0x129/0x330 [amdgpu] Fixes: a64c9e15e624 ("drm/amd/powerplay: cleanup the interfaces for powergate setting through SMU") Signed-off-by: Evan Quan <evan.quan@amd.com> Reported-by: Rui Teng <Rui.Teng@amd.com> Acked-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu: only set cp active field for kiq queueHuang Rui
The mec ucode will set the CP_HQD_ACTIVE bit while the queue is mapped by MAP_QUEUES packet. So we only need set cp active field for kiq queue. Signed-off-by: Huang Rui <ray.huang@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdkfd: Add a message when SW scheduler is usedYong Zhao
SW scheduler is previously called non HW scheduler, or non HWS. This message is useful when triaging issues from dmesg. Signed-off-by: Yong Zhao <Yong.Zhao@amd.com> Acked-by: Huang Rui <ray.huang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu/pm: clean up return typesAlex Deucher
count is size_t so don't use negative values. Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/scheduler: improve job distribution with multiple queuesNirmoy Das
This patch uses score based logic to select a new rq for better loadbalance between multiple rq/scheds instead of num_jobs. Below are test results after running amdgpu_test from mesa drm Before this patch: sched_name num of many times it got scheduled ========= ================================== sdma0 314 sdma1 32 comp_1.0.0 56 comp_1.0.1 0 comp_1.1.0 0 comp_1.1.1 0 comp_1.2.0 0 comp_1.2.1 0 comp_1.3.0 0 comp_1.3.1 0 After this patch: sched_name num of many times it got scheduled ========= ================================== sdma0 216 sdma1 185 comp_1.0.0 39 comp_1.0.1 9 comp_1.1.0 12 comp_1.1.1 0 comp_1.2.0 12 comp_1.2.1 0 comp_1.3.0 12 comp_1.3.1 0 Signed-off-by: Nirmoy Das <nirmoy.das@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu/vcn2.5: implement indirect DPG SRAM modeJames Zhu
Implement indirect DPG SRAM mode for vcn2.5 Signed-off-by: James Zhu <James.Zhu@amd.com> Reviewed-by: Leo Liu <leo.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu/vcn2.5: add dpg pause modeJames Zhu
Add dpg pause mode support for vcn2.5 Signed-off-by: James Zhu <James.Zhu@amd.com> Reviewed-by: Leo Liu <leo.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu/vcn2.5: add DPG mode start and stopJames Zhu
Add DPG mode start and stop functions for vcn2.5 v2: Correct firmware ucode index in vcn_v2_5_mc_resume_dpg_mode Signed-off-by: James Zhu <James.Zhu@amd.com> Reviewed-by: Leo Liu <leo.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu/vcn: move macro from vcn2.0 to share amdgpu_vcn (v2)James Zhu
Move macro from vcn2.0 to amdgpu_vcn to share with vcn2.5 v2: squash in macro fix Signed-off-by: James Zhu <James.Zhu@amd.com> Reviewed-by: Leo Liu <leo.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu/vcn: support multiple instance direct SRAM read and write (v2)James Zhu
Add multiple instance direct SRAM read and write support for vcn2.5 v2: squash in indexing fix Signed-off-by: James Zhu <James.Zhu@amd.com> Reviewed-by: Leo Liu <leo.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu/vcn: support multiple-instance dpg pause modeJames Zhu
Add multiple-instance dpg pause mode support for VCN2.5 Signed-off-by: James Zhu <James.Zhu@amd.com> Reviewed-by: Leo Liu <leo.liu@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu/sriov skip the update of SMU_TABLE_ACTIVITY_MONITOR_COEFFJack Zhang
There's no need to dump ACTIVITY_MONITOR_COEFF under VF. Therefore, Skip the update of SMU_TABLE_ACTIVITY_MONITOR_COEFF under SRIOV VF. Signed-off-by: Jack Zhang <Jack.Zhang1@amd.com> Reviewed-by: Evan Quan <evan.quan@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu: fix modprobe failure of the secondary GPU when GDDR6 training ↵Tianci.Yin
enabled(V5) [why] In dual GPUs scenario, stolen_size is assigned to zero on the secondary GPU, since there is no pre-OS console using that memory. Then the bottom region of VRAM was allocated as GTT, unfortunately a small region of bottom VRAM was encroached by UMC firmware during GDDR6 BIST training, this cause page fault. [how] Forcing stolen_size to 3MB, then the bottom region of VRAM was allocated as stolen memory, GTT corruption avoid. Reviewed-by: Christian König <christian.koenig@amd.com> Reviewed-by: Feifei Xu <Feifei.Xu@amd.com> Signed-off-by: Tianci.Yin <tianci.yin@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu/gfx10: update gfx golden settings for navi14Tianci.Yin
remove registers: mmSPI_CONFIG_CNTL add registers: mmSPI_CONFIG_CNTL_1 Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Tianci.Yin <tianci.yin@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu/gfx10: update gfx golden settingsTianci.Yin
remove registers: mmSPI_CONFIG_CNTL add registers: mmSPI_CONFIG_CNTL_1 Reviewed-by: Alex Deucher <alexander.deucher@amd.com> Signed-off-by: Tianci.Yin <tianci.yin@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu: check rlc_g firmware pointer is valid before using itshaoyunl
In SRIOV, rlc_g firmware is loaded by host, guest driver won't load it which will cause the rlc_fw pointer is null Signed-off-by: shaoyunl <shaoyun.liu@amd.com> Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu: drop amdgpu_job.ownerChristian König
Entirely unused. Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu: error out on entity with no run queueNirmoy Das
Disabled HW IP's entity initialized with NULL rq. We should not process any submit request from userspace for a disabled HW IP. Signed-off-by: Nirmoy Das <nirmoy.das@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdkfd: use map_queues for hiq on gfx v10 as wellHuang Rui
To align with gfx v9, we use the map_queues packet to load hiq MQD. Signed-off-by: Huang Rui <ray.huang@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdkfd: use kiq to load the mqd of hiq queue for gfx v9 (v6)Aaron Liu
There is an issue that CP will check the HIQ queue to be configured and mapped with KIQ ring, otherwise, it will be unable to read back the secure buffer while the gfxoff is enabled even with trusted IP blocks. v1 -> v2: - Fix to remove surplus set_resources packets. - Fill the whole configuration in MQD. - Change the author as Aaron because he addressed the key point of this issue. - Add kiq ring lock. v2 -> v3: - Free the lock while in error return case. - Remove the programming only needed by the queue is unmapped. v3 -> v4: - Remove doorbell programming because it's used for restarting queue. - Remove CP scheduler programming because map_queue packet will handle this. v4 -> v5: - Remove cp_hqd_active because mec ucode will enable it while use map_queues. - Revise goto out_unlock. - Correct the right doorbell offset for HIQ that kfd driver assigned in the packet. v5 -> v6: - Merge Arcturus fix into this patch because it will get oops in Arcturus platform. Reported-by: Lisa Saturday <Lisa.Saturday@amd.com> Signed-off-by: Aaron Liu <aaron.liu@amd.com> Signed-off-by: Huang Rui <ray.huang@amd.com> Reviewed-and-Tested-by: Aaron Liu <aaron.liu@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu: flush TLB functions removal from kfd2kgd interfaceAlex Sierra
[Why] kfd2kgd interface will be deprecated. This removal only covers TLB invalidation for now. They have been replaced in amdgpu_amdkfd API. [How] TLB invalidate functions removed from the different amdkfd_gfx_v* versions. Signed-off-by: Alex Sierra <alex.sierra@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu: GPU TLB flush API moved to amdgpu_amdkfdAlex Sierra
[Why] TLB flush method has been deprecated using kfd2kgd interface. This implementation is now on the amdgpu_amdkfd API. [How] TLB flush functions now implemented in amdgpu_amdkfd. Signed-off-by: Alex Sierra <alex.sierra@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu: export function to flush TLB via pasidAlex Sierra
This can be used directly from amdgpu and amdkfd to invalidate TLB through pasid. It supports gmc v7, v8, v9 and v10. Signed-off-by: Alex Sierra <alex.sierra@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu: replace kcq enable/disable functions on gfx_v9Alex Sierra
[Why] There are HW-indpendent functions that enables and disables kcq. These functions use the kiq_pm4_funcs implementation. [How] Local kcq enable and disable functions removed and replace it by the generic kcq enable under amdgpu_gfx Signed-off-by: Alex Sierra <alex.sierra@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu: implement tlbs invalidate on gfx9 gfx10Alex Sierra
tlbs invalidate pointer function added to kiq_pm4_funcs struct. This way, tlb flush can be done through kiq member. TLBs invalidatation implemented for gfx9 and gfx10. Signed-off-by: Alex Sierra <alex.sierra@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu: kiq pm4 function implementation for gfx_v9Alex Sierra
Functions implemented from kiq_pm4_funcs struct members for gfx_v9 version. Signed-off-by: Alex Sierra <alex.sierra@amd.com> Acked-by: Christian König <christian.koenig@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16drm/amdgpu: Avoid reclaim fs while eviction lockAlex Sierra
[Why] Avoid reclaim filesystem while eviction lock is held called from MMU notifier. [How] Setting PF_MEMALLOC_NOFS flags while eviction mutex is locked. Using memalloc_nofs_save / memalloc_nofs_restore API. Signed-off-by: Alex Sierra <alex.sierra@amd.com> Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com> Reviewed-by: Christian König <christian.koenig@amd.com> Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
2020-01-16Merge tag 'tag-chrome-platform-fixes-for-v5.5-rc7' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux Pull chrome platform fix from Benson Leung: "One fix in the wilco_ec keyboard backlight driver to allow the EC driver to continue loading in the absence of a backlight module" * tag 'tag-chrome-platform-fixes-for-v5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/chrome-platform/linux: platform/chrome: wilco_ec: Fix keyboard backlight probing
2020-01-16USB: serial: option: add support for Quectel RM500Q in QDL modeReinhard Speyerer
Add support for Quectel RM500Q in QDL mode. T: Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 24 Spd=480 MxCh= 0 D: Ver= 2.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=2c7c ProdID=0800 Rev= 0.00 S: Manufacturer=Qualcomm CDMA Technologies MSM S: Product=QUSB_BULK_SN:xxxxxxxx S: SerialNumber=xxxxxxxx C:* #Ifs= 1 Cfg#= 1 Atr=a0 MxPwr= 2mA I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=10 Driver=option E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms It is assumed that the ZLP flag required for other Qualcomm-based 5G devices also applies to Quectel RM500Q. Signed-off-by: Reinhard Speyerer <rspmn@arcor.de> Cc: stable <stable@vger.kernel.org> Signed-off-by: Johan Hovold <johan@kernel.org>
2020-01-16netfilter: nat: fix ICMP header corruption on ICMP errorsEyal Birger
Commit 8303b7e8f018 ("netfilter: nat: fix spurious connection timeouts") made nf_nat_icmp_reply_translation() use icmp_manip_pkt() as the l4 manipulation function for the outer packet on ICMP errors. However, icmp_manip_pkt() assumes the packet has an 'id' field which is not correct for all types of ICMP messages. This is not correct for ICMP error packets, and leads to bogus bytes being written the ICMP header, which can be wrongfully regarded as 'length' bytes by RFC 4884 compliant receivers. Fix by assigning the 'id' field only for ICMP messages that have this semantic. Reported-by: Shmulik Ladkani <shmulik.ladkani@gmail.com> Fixes: 8303b7e8f018 ("netfilter: nat: fix spurious connection timeouts") Signed-off-by: Eyal Birger <eyal.birger@gmail.com> Acked-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-01-16net: wan: lapbether.c: Use built-in RCU list checkingMadhuparna Bhowmik
The only callers of the function lapbeth_get_x25_dev() are lapbeth_rcv() and lapbeth_device_event(). lapbeth_rcv() uses rcu_read_lock() whereas lapbeth_device_event() is called with RTNL held (As mentioned in the comments). Therefore, pass lockdep_rtnl_is_held() as cond argument in list_for_each_entry_rcu(); Signed-off-by: Madhuparna Bhowmik <madhuparnabhowmik04@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-16netfilter: nf_tables: fix flowtable list del corruptionFlorian Westphal
syzbot reported following crash: list_del corruption, ffff88808c9bb000->prev is LIST_POISON2 (dead000000000122) [..] Call Trace: __list_del_entry include/linux/list.h:131 [inline] list_del_rcu include/linux/rculist.h:148 [inline] nf_tables_commit+0x1068/0x3b30 net/netfilter/nf_tables_api.c:7183 [..] The commit transaction list has: NFT_MSG_NEWTABLE NFT_MSG_NEWFLOWTABLE NFT_MSG_DELFLOWTABLE NFT_MSG_DELTABLE A missing generation check during DELTABLE processing causes it to queue the DELFLOWTABLE operation a second time, so we corrupt the list here: case NFT_MSG_DELFLOWTABLE: list_del_rcu(&nft_trans_flowtable(trans)->list); nf_tables_flowtable_notify(&trans->ctx, because we have two different DELFLOWTABLE transactions for the same flowtable. We then call list_del_rcu() twice for the same flowtable->list. The object handling seems to suffer from the same bug so add a generation check too and only queue delete transactions for flowtables/objects that are still active in the next generation. Reported-by: syzbot+37a6804945a3a13b1572@syzkaller.appspotmail.com Fixes: 3b49e2e94e6eb ("netfilter: nf_tables: add flow table netlink frontend") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-01-16netfilter: nf_tables: fix memory leak in nf_tables_parse_netdev_hooks()Dan Carpenter
Syzbot detected a leak in nf_tables_parse_netdev_hooks(). If the hook already exists, then the error handling doesn't free the newest "hook". Reported-by: syzbot+f9d4095107fc8749c69c@syzkaller.appspotmail.com Fixes: b75a3e8371bc ("netfilter: nf_tables: allow netdevice to be used only once per flowtable") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-01-16netfilter: nf_tables: remove WARN and add NLA_STRING upper limitsFlorian Westphal
This WARN can trigger because some of the names fed to the module autoload function can be of arbitrary length. Remove the WARN and add limits for all NLA_STRING attributes. Reported-by: syzbot+0e63ae76d117ae1c3a01@syzkaller.appspotmail.com Fixes: 452238e8d5ffd8 ("netfilter: nf_tables: add and use helper for module autoload") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
2020-01-16netfilter: nft_tunnel: ERSPAN_VERSION must not be nullFlorian Westphal
Fixes: af308b94a2a4a5 ("netfilter: nf_tables: add tunnel support") Signed-off-by: Florian Westphal <fw@strlen.de> Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
generated by cgit (git 2.34.1) at 2025-09-12 05:01:01 +0000