| Age | Commit message (Collapse) | Author |
|---|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into fixes
Pull "Allwinner fixes for 4.15" from Chen-Yu Tsai:
First, one fix that adds proper regulator references for the EMAC
external PHYs on A64 boards. The EMAC bindings were developed for 4.13,
but reverted at the last minute. They were finalized and brought back
for 4.15. However in the time between, regulator support for the A64
boards was merged. When EMAC device tree changes were reintroduced,
this was not taken into account.
Second, a patch that adds OF based modalias uevent for RSB slave devices.
This has been missing since the introduction of RSB, and recently with
PMIC regulator support introduced for the A64, has been seen affecting
distributions, which have the all-important PMIC mfd drivers built as
modules, which then don't get loaded.
Other minor cleanups include final conversion of raw indices to CCU
binding macros for sun[4567]i HDMI, cleanup of dummy regulators on the
A64 SOPINE, a SD card detection polarity fix for the Orange Pi Zero
Plus2, and adding a missing compatible for the PMIC on the TBS A711
tablet.
* tag 'sunxi-fixes-for-4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/sunxi/linux:
ARM: dts: sun8i: a711: Reinstate the PMIC compatible
arm64: dts: orange-pi-zero-plus2: fix sdcard detect
arm64: allwinner: a64-sopine: Fix to use dcdc1 regulator instead of vcc3v3
ARM: dts: sunxi: Convert to CCU index macros for HDMI controller
sunxi-rsb: Include OF based modalias in device uevent
arm64: allwinner: a64: add Ethernet PHY regulator for several boards
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
Pull "Renesas ARM Based SoC Fixes for v4.15" from Simon Horman:
Vladimir Zapolskiy says:
The present change is a bug fix for AVB link iteratively up/down.
Steps to reproduce:
- start AVB TX stream (Using aplay via MSE),
- disconnect+reconnect the eth cable,
- after a reconnection the eth connection goes iteratively up/down
without user interaction,
- this may heal after some seconds or even stay for minutes.
As the documentation specifies, the "renesas,no-ether-link" option
should be used when a board does not provide a proper AVB_LINK signal.
There is no need for this option enabled on RCAR H3/M3 Salvator-X/XS
and ULCB starter kits since the AVB_LINK is correctly handled by HW.
Choosing to keep or remove the "renesas,no-ether-link" option will
have impact on the code flow in the following ways:
- keeping this option enabled may lead to unexpected behavior since
the RX & TX are enabled/disabled directly from adjust_link function
without any HW interrogation,
- removing this option, the RX & TX will only be enabled/disabled after
HW interrogation. The HW check is made through the LMON pin in PSR
register which specifies AVB_LINK signal value (0 - at low level;
1 - at high level).
In conclusion, the change is also a safety improvement because it
removes the "renesas,no-ether-link" option leading to a proper way
of detecting the link state based on HW interrogation and not on
software heuristic.
Note that DTS files for V3M Starter Kit, Draak and Eagle boards
contain the same property, the files are untouched due to unavailable
schematics to verify if the fix applies to these boards as well.
* tag 'renesas-fixes-for-v4.15' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
arm64: dts: renesas: ulcb: Remove renesas, no-ether-link property
arm64: dts: renesas: salvator-x: Remove renesas, no-ether-link property
|
|
In the function l2cap_parse_conf_rsp and in the function
l2cap_parse_conf_req the following variable is declared without
initialization:
struct l2cap_conf_efs efs;
In addition, when parsing input configuration parameters in both of
these functions, the switch case for handling EFS elements may skip the
memcpy call that will write to the efs variable:
...
case L2CAP_CONF_EFS:
if (olen == sizeof(efs))
memcpy(&efs, (void *)val, olen);
...
The olen in the above if is attacker controlled, and regardless of that
if, in both of these functions the efs variable would eventually be
added to the outgoing configuration request that is being built:
l2cap_add_conf_opt(&ptr, L2CAP_CONF_EFS, sizeof(efs), (unsigned long) &efs);
So by sending a configuration request, or response, that contains an
L2CAP_CONF_EFS element, but with an element length that is not
sizeof(efs) - the memcpy to the uninitialized efs variable can be
avoided, and the uninitialized variable would be returned to the
attacker (16 bytes).
This issue has been assigned CVE-2017-1000410
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Ben Seri <ben@armis.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jberg/mac80211
Johannes Berg says:
====================
Two fixes:
* drop mesh frames appearing to be from ourselves
* check another netlink attribute for existence
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the OSS emulation plugin builder where the frame size is parsed in
the plugin chain, some places miss the possible errors returned from
the plugin src_ or dst_frames callback.
This patch papers over such places.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This patch adds the missing CAN_ERR_CRTL to cf->can_id in case of
CAN_STATE_ERROR_WARNING or CAN_STATE_ERROR_PASSIVE
Signed-off-by: Martin Lederhilger <m.lederhilger@ds-automotion.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The flexcan_start_xmit() function compares the frame length with data
register length to write frame content into data[0] and data[1]
register. Data register length is 4 bytes and frame maximum length is 8
bytes.
Fix the check that compares frame length with 3. Because the register
length is 4.
Signed-off-by: Luu An Phu <phu.luuan@nxp.com>
Reviewed-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The "set_bittiming" callback treats a positive return value as error!
For that reason "can_changelink()" will quit silently after setting
the bittiming values without processing ctrlmode, restart-ms, etc.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Picking up the patch from Serhey Popovych (commit 191cdb3822e5df6b3c8,
"veth: Be more robust on network device creation when no attributes").
When the peer name attribute is not provided the former implementation tries
to register the given device name twice ... which leads to -EEXIST.
If only one device name is given apply an automatic generated and valid name
for the peer.
Cc: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Models such as BCM5395/97/98 and BCM53125/24/53115 and compatible require that
we turn on managed mode to actually act on Broadcom tags, otherwise they just
pass them through on ingress (host -> switch) and don't insert them in egress
(switch -> host). Turning on managed mode is simple, but requires us to
properly support ARL misses on multicast addresses which is a much more
involved set of changes not suitable for a bug fix for this release.
Reported-by: Jochen Friedrich <jochen@scram.de>
Fixes: 7edc58d614d4 ("net: dsa: b53: Turn on Broadcom tags")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds the ELV ALC 8xxx Battery Charging device
to the list of USB IDs of drivers/usb/serial/cp210x.c
Signed-off-by: Christian Holl <cyborgx1@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
If there are multiple mesh stations with the same MAC address,
they will both get confused and start throwing warnings.
Obviously in this case nothing can actually work anyway, so just
drop frames that look like they're from ourselves early on.
Reported-by: Gui Iribarren <gui@altermundi.net>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
nl80211_nan_add_func() does not check if the required attribute
NL80211_NAN_FUNC_FOLLOW_UP_DEST is present when processing
NL80211_CMD_ADD_NAN_FUNCTION request. This request can be issued
by users with CAP_NET_ADMIN privilege and may result in NULL dereference
and a system crash. Add a check for the required attribute presence.
Signed-off-by: Hao Chen <flank3rsky@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
Display WA #1183 was recently added to workaround
"Failures when enabling DPLL0 with eDP link rate 2.16
or 4.32 GHz and CD clock frequency 308.57 or 617.14 MHz
(CDCLK_CTL CD Frequency Select 10b or 11b) used in this
enabling or in previous enabling."
This workaround was designed to minimize the impact only
to save the bad case with that link rates. But HW engineers
indicated that it should be safe to apply broadly, although
they were expecting the DPLL0 link rate to be unchanged on
runtime.
We need to cover 2 cases: when we are in fact enabling DPLL0
and when we are just changing the frequency with small
differences.
This is based on previous patch by Rodrigo Vivi with suggestions
from Ville Syrjälä.
Cc: Arthur J Runyan <arthur.j.runyan@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20171204232210.4958-1-lucas.demarchi@intel.com
(cherry picked from commit 53421c2fe99ce16838639ad89d772d914a119a49)
[ Lucas: Backport to 4.15 adding back variable that has been removed on
commits not meant to be backported ]
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180102201837.6812-1-lucas.demarchi@intel.com
|
|
The global array clashes with a newly added symbol of the same name:
drivers/staging/ccree/cc_debugfs.o:(.data+0x0): multiple definition of `debug_regs'
drivers/mmc/host/s3cmci.o:(.data+0x70): first defined here
We should fix both, this one addresses the s3cmci driver by removing
the symbol from the global namespace. While at it, this separates
the declaration from the type definition and makes the variable const.
Fixes: 9bdd203b4dc8 ("s3cmci: add debugfs support for examining driver and hardware state")
Fixes: b3ec9a6736f2 ("staging: ccree: staging: ccree: replace sysfs by debugfs interface")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
A shadow page table entry needs to be cleared after being set as
post-sync. This patch fixes the recent error reported in Win7-32 test.
Fixes: 2707e4446688 ("drm/i915/gvt: vGPU graphics memory virtualization")
Signed-off-by: Zhi Wang <zhi.a.wang@intel.com>
CC: Stable <stable@vger.kernel.org>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
|
|
Make sure that the initiator port GUID is stored in ch->ini_guid.
Note: when initiating a connection sgid and dgid members in struct
sa_path_rec represent the source and destination GIDs. When accepting
a connection however sgid represents the destination GID and dgid the
source GID.
Fixes: commit 2bce1a6d2209 ("IB/srpt: Accept GUIDs as port names")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
With the SRP protocol all RDMA operations are initiated by the target.
Since no RDMA operations are initiated by the initiator, do not grant
the initiator permission to submit RDMA reads or writes to the target.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 page table isolation fixes from Thomas Gleixner:
"A couple of urgent fixes for PTI:
- Fix a PTE mismatch between user and kernel visible mapping of the
cpu entry area (differs vs. the GLB bit) and causes a TLB mismatch
MCE on older AMD K8 machines
- Fix the misplaced CR3 switch in the SYSCALL compat entry code which
causes access to unmapped kernel memory resulting in double faults.
- Fix the section mismatch of the cpu_tss_rw percpu storage caused by
using a different mechanism for declaration and definition.
- Two fixes for dumpstack which help to decode entry stack issues
better
- Enable PTI by default in Kconfig. We should have done that earlier,
but it slipped through the cracks.
- Exclude AMD from the PTI enforcement. Not necessarily a fix, but if
AMD is so confident that they are not affected, then we should not
burden users with the overhead"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/process: Define cpu_tss_rw in same section as declaration
x86/pti: Switch to kernel CR3 at early in entry_SYSCALL_compat()
x86/dumpstack: Print registers for first stack frame
x86/dumpstack: Fix partial register dumps
x86/pti: Make sure the user/kernel PTEs match
x86/cpu, x86/pti: Do not enable PTI on AMD processors
x86/pti: Enable PTI by default
|
|
We were calling enable_irq on bind, where it was already enabled previously
by the IRQ helper. Additionally, dev->irq is not set correctly until after
postinstall and so was always zero here, triggering a warning in 4.15.
Fix both by moving the enable to the power management resume path, where we
know there was a previous disable invocation during suspend.
Fixes: 253696ccd613 ("drm/vc4: Account for interrupts in flight")
Signed-off-by: Stefan Schake <stschake@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Link: https://patchwork.freedesktop.org/patch/msgid/1514563543-32511-1-git-send-email-stschake@gmail.com
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Eric Anholt <eric@anholt.net>
|
|
cpu_tss_rw is declared with DECLARE_PER_CPU_PAGE_ALIGNED
but then defined with DEFINE_PER_CPU_SHARED_ALIGNED
leading to section mismatch warnings.
Use DEFINE_PER_CPU_PAGE_ALIGNED consistently. This is necessary because
it's mapped to the cpu entry area and must be page aligned.
[ tglx: Massaged changelog a bit ]
Fixes: 1a935bc3d4ea ("x86/entry: Move SYSENTER_stack to the beginning of struct tss_struct")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: thomas.lendacky@amd.com
Cc: Borislav Petkov <bpetkov@suse.de>
Cc: tklauser@distanz.ch
Cc: minipli@googlemail.com
Cc: me@kylehuey.com
Cc: namit@vmware.com
Cc: luto@kernel.org
Cc: jpoimboe@redhat.com
Cc: tj@kernel.org
Cc: cl@linux.com
Cc: bp@suse.de
Cc: thgarnie@google.com
Cc: kirill.shutemov@linux.intel.com
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20180103203954.183360-1-ndesaulniers@google.com
|
|
The preparation for PTI which added CR3 switching to the entry code
misplaced the CR3 switch in entry_SYSCALL_compat().
With PTI enabled the entry code tries to access a per cpu variable after
switching to kernel GS. This fails because that variable is not mapped to
user space. This results in a double fault and in the worst case a kernel
crash.
Move the switch ahead of the access and clobber RSP which has been saved
already.
Fixes: 8a09317b895f ("x86/mm/pti: Prepare the x86/entry assembly code for entry/exit CR3 switching")
Reported-by: Lars Wendler <wendler.lars@web.de>
Reported-by: Laura Abbott <labbott@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Borislav Betkov <bp@alien8.de>
Cc: Andy Lutomirski <luto@kernel.org>,
Cc: Dave Hansen <dave.hansen@linux.intel.com>,
Cc: Peter Zijlstra <peterz@infradead.org>,
Cc: Greg KH <gregkh@linuxfoundation.org>, ,
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>,
Cc: Juergen Gross <jgross@suse.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1801031949200.1957@nanos
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace
Pull pid allocation bug fix from Eric Biederman:
"The replacement of the pid hash table and the pid bitmap with an idr
resulted in an implementation that now fails more often in low memory
situations. Allowing fuzzers to observe bad behavior from a memory
allocation failure during pid allocation.
This is a small change to fix this by making the kernel more robust in
the case of error. The non-error paths are left alone so the only
danger is to the already broken error path. I have manually injected
errors and verified that this new error handling works"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace:
pid: Handle failure to allocate the first pid in a pid namespace
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs
Pull afs/fscache fixes from David Howells:
- Fix the default return of fscache_maybe_release_page() when a cache
isn't in use - it prevents a filesystem from releasing pages. This
can cause a system to OOM.
- Fix a potential uninitialised variable in AFS.
- Fix AFS unlink's handling of the nlink count. It needs to use the
nlink manipulation functions so that inode structs of deleted inodes
actually get scheduled for destruction.
- Fix error handling in afs_write_end() so that the page gets unlocked
and put if we can't fill the unwritten portion.
* 'afs-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs:
afs: Fix missing error handling in afs_write_end()
afs: Fix unlink
afs: Potential uninitialized variable in afs_extract_data()
fscache: Fix the default for fscache_maybe_release_page()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security
Pull capabilities fix from James Morris.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/linux-security:
capabilities: fix buffer overread on very short xattr
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-01-03
This series contains fixes for i40e and i40evf.
Amritha removes the UDP support for big buffer cloud filters since it is
not supported and having UDP enabled is a bug.
Alex fixes a bug in the __i40e_chk_linearize() which did not take into
account large (16K or larger) fragments that are split over 2 descriptors,
which could result in a transmit hang.
Jake fixes an issue where a devices own MAC address could be removed from
the unicast address list, so force a check on every address sync to ensure
removal does not happen.
Jiri Pirko fixes the return value when a filter configuration is not
supported, do not return "invalid" but return "not supported" so that
the core can react correctly.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A few spots in 3c59x missed calls to dma_mapping_error checks, casuing
WARN_ONS to trigger. Clean those up. While we're at it, refactor the
refill code a bit so that if skb allocation or dma mapping fails, we
recycle the existing buffer. This prevents holes in the rx ring, and
makes for much simpler logic
Note: This is compile only tested. Ted, if you could run this and
confirm that it continues to work properly, I would appreciate it, as I
currently don't have access to this hardware
Signed-off-by: Neil Horman <nhorman@redhat.com>
CC: Steffen Klassert <klassert@mathematik.tu-chemnitz.de>
CC: "David S. Miller" <davem@davemloft.net>
Reported-by: tedheadster@gmail.com
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a logical revert of commit e37fdb785a5f ("exec: Use secureexec
for setting dumpability")
This weakens dumpability back to checking only for uid/gid changes in
current (which is useless), but userspace depends on dumpability not
being tied to secureexec.
https://bugzilla.redhat.com/show_bug.cgi?id=1528633
Reported-by: Tom Horsley <horsley1953@gmail.com>
Fixes: e37fdb785a5f ("exec: Use secureexec for setting dumpability")
Cc: stable@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Netanel Belgazal says:
====================
bug fixes for ENA Ethernet driver
Changes from V1:
Revome incorrect "ena: invoke netif_carrier_off() only after netdev
registered" patch
This patchset contains 2 bug fixes:
* handle rare race condition during MSI-X initialization
* fix error processing in ena_down()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ENA admin command queue errors are not handled as part of ena_down().
As a result, in case of error admin queue transitions to non-running
state and aborts all subsequent commands including those coming from
ena_up(). Reset scheduled by the driver from the timer service
context would not proceed due to sharing rtnl with ena_up()/ena_down()
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Under certain conditions MSI-X interrupt might arrive right after it
was unmasked in ena_up(). There is a chance it would be processed by
the driver before device ENA_FLAG_DEV_UP flag is set. In such a case
the interrupt is ignored.
ENA device operates in auto-masked mode, therefore ignoring
interrupt leaves it masked for good.
Moving unmask of interrupt to be the last step in ena_up().
Signed-off-by: Netanel Belgazal <netanel@amazon.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 96ac18f14a5a ("cxgb4: Add support for new flash parts")
removed initialization of adapter->params.sf_fw_start causing issues
while flashing firmware to card. We no longer need sf_fw_start
in adapter->params as we already have macros defined for FW flash
addresses.
Fixes: 96ac18f14a5a ("cxgb4: Add support for new flash parts")
Signed-off-by: Arjun Vynipadath <arjun@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When filter configuration is not supported, drivers should return
-EOPNOTSUPP so the core can react correctly.
Fixes: 2f4b411a3d67 ("i40e: Enable cloud filters via tc-flower")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In some circumstances, such as with bridging, it is possible that the
stack will add a devices own MAC address to its unicast address list.
If, later, the stack deletes this address, then the i40e driver will
receive a request to remove this address.
The driver stores its current MAC address as part of the MAC/VLAN hash
array, since it is convenient and matches exactly how the hardware
expects to be told which traffic to receive.
This causes a problem, since for more devices, the MAC address is stored
separately, and requests to delete a unicast address should not have the
ability to remove the filter for the MAC address.
Fix this by forcing a check on every address sync to ensure we do not
remove the device address.
There is a very narrow possibility of a race between .set_mac and
.set_rx_mode, if we don't change netdev->dev_addr before updating our
internal MAC list in .set_mac. This might be possible if .set_rx_mode is
going to remove MAC "XYZ" from the list, at the same time as .set_mac
changes our dev_addr to MAC "XYZ", we might possibly queue a delete,
then an add in .set_mac, then queue a delete in .set_rx_mode's
dev_uc_sync and then update netdev->dev_addr. We can avoid this by
moving the copy into dev_addr prior to the changes to the MAC filter
list.
A similar race on the other side does not cause problems, as if we're
changing our MAC form A to B, and we race with .set_rx_mode, it could
queue a delete from A, we'd update our address, and allow the delete.
This seems like a race, but in reality we're about to queue a delete of
A anyways, so it would not cause any issues.
A race in the initialization code is unlikely because the netdevice has
not yet been fully initialized and the stack should not be adding or
removing addresses yet.
Note that we don't (yet) need similar code for the VF driver because it
does not make use of __dev_uc_sync and __dev_mc_sync, but instead roles
its own method for handling updates to the MAC/VLAN list, which already
has code to protect against removal of the hardware address.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
linearize
The original code for __i40e_chk_linearize didn't take into account the
fact that if a fragment is 16K in size or larger it has to be split over 2
descriptors and the smaller of those 2 descriptors will be on the trailing
edge of the transmit. As a result we can get into situations where we didn't
catch requests that could result in a Tx hang.
This patch takes care of that by subtracting the length of all but the
trailing edge of the stale fragment before we test for sum. By doing this
we can guarantee that we have all cases covered, including the case of a
fragment that spans multiple descriptors. We don't need to worry about
checking the inner portions of this since 12K is the maximum aligned DMA
size and that is larger than any MSS will ever be since the MTU limit for
jumbos is something on the order of 9K.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fugang Duan says:
====================
net: fec: clean up in the cases of probe error
The simple patches just clean up in the cases of probe error like restore dev_id and
handle the defer probe when regulator is still not ready.
v2:
* Fabio Estevam's comment to suggest split v1 to separate patches.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Defer probe if regulator is not ready. E.g. some regulator is fixed
regulator controlled by i2c expander gpio, the i2c device may be probed
after the driver, then it should handle the case of defer probe error.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The static variable dev_id always plus one before netdev registerred.
It should restore the dev_id value in the cases of probe error.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since UDP based filters are not supported via big buffer cloud
filters, remove UDP support. Also change a few return types to
indicate unsupported vs invalid configuration.
Signed-off-by: Amritha Nambiar <amritha.nambiar@intel.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Fix indentation of reserved_flags2 field in vxlanhdr_gpe.
Fixes: e1e5314de08b ("vxlan: implement GPE")
Signed-off-by: William Tu <u9012063@gmail.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
syzbot noticed a NULL pointer dereference panic in sctp_stream_free()
which was caused by an incomplete error handling in sctp_stream_init().
By not clearing stream->outcnt, it made a for() in sctp_stream_free()
think that it had elements to free, but not, leading to the panic.
As suggested by Xin Long, this patch also simplifies the error path by
moving it to the only if() that uses it.
See-also: https://www.spinics.net/lists/netdev/msg473756.html
See-also: https://www.spinics.net/lists/netdev/msg465024.html
Reported-by: syzbot <syzkaller@googlegroups.com>
Fixes: f952be79cebd ("sctp: introduce struct sctp_stream_out_ext")
Signed-off-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2018-01-02
This series contains fixes for e1000 and e1000e.
Tushar Dave adds a check to the driver so that it won't attempt to disable a
device that is already disabled for e1000.
Benjamin Poirier provides a fix to e1000e, where a previous commit that
Benjamin submitted changed the meaning of the return value for
"check_for_link" for copper media and not all the instances were properly
updated. Benjamin fixes the remaining instances that needed the change.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When args->nr_local is 0, nr_pages gets also 0 due some size
calculation via rds_rm_size(), which is later used to allocate
pages for DMA, this bug produces a heap Out-Of-Bound write access
to a specific memory region.
Signed-off-by: Mohamed Ghannam <simo.ghannam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
libc-compat.h aims to prevent symbol collisions between uapi and libc
headers for each supported libc. This requires continuous coordination
between them.
The goal of this commit is to improve the situation for libcs (such as
musl) which are not yet supported and/or do not wish to be explicitly
supported, while not affecting supported libcs. More precisely, with
this commit, unsupported libcs can request the suppression of any
specific uapi definition by defining the correspondings _UAPI_DEF_*
macro as 0. This can fix symbol collisions for them, as long as the
libc headers are included before the uapi headers. Inclusion in the
other order is outside the scope of this commit.
All infrastructure in order to enable this fallback for unsupported
libcs is already in place, except that libc-compat.h unconditionally
defines all _UAPI_DEF_* macros to 1 for all unsupported libcs so that
any previous definitions are ignored. In order to fix this, this commit
merely makes these definitions conditional.
This commit together with the musl libc commit
http://git.musl-libc.org/cgit/musl/commit/?id=04983f2272382af92eb8f8838964ff944fbb8258
fixes for example the following compiler errors when <linux/in6.h> is
included after musl's <netinet/in.h>:
./linux/in6.h:32:8: error: redefinition of 'struct in6_addr'
./linux/in6.h:49:8: error: redefinition of 'struct sockaddr_in6'
./linux/in6.h:59:8: error: redefinition of 'struct ipv6_mreq'
The comments referencing glibc are still correct, but this file is not
only used for glibc any more.
Signed-off-by: Felix Janda <felix.janda@posteo.de>
Reviewed-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the stack dump code, if the frame after the starting pt_regs is also
a regs frame, the registers don't get printed. Fix that.
Reported-by: Andy Lutomirski <luto@amacapital.net>
Tested-by: Alexander Tsoy <alexander@tsoy.me>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toralf Förster <toralf.foerster@gmx.de>
Cc: stable@vger.kernel.org
Fixes: 3b3fa11bc700 ("x86/dumpstack: Print any pt_regs found on the stack")
Link: http://lkml.kernel.org/r/396f84491d2f0ef64eda4217a2165f5712f6a115.1514736742.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The show_regs_safe() logic is wrong. When there's an iret stack frame,
it prints the entire pt_regs -- most of which is random stack data --
instead of just the five registers at the end.
show_regs_safe() is also poorly named: the on_stack() checks aren't for
safety. Rename the function to show_regs_if_on_stack() and add a
comment to explain why the checks are needed.
These issues were introduced with the "partial register dump" feature of
the following commit:
b02fcf9ba121 ("x86/unwinder: Handle stack overflows more gracefully")
That patch had gone through a few iterations of development, and the
above issues were artifacts from a previous iteration of the patch where
'regs' pointed directly to the iret frame rather than to the (partially
empty) pt_regs.
Tested-by: Alexander Tsoy <alexander@tsoy.me>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Toralf Förster <toralf.foerster@gmx.de>
Cc: stable@vger.kernel.org
Fixes: b02fcf9ba121 ("x86/unwinder: Handle stack overflows more gracefully")
Link: http://lkml.kernel.org/r/5b05b8b344f59db2d3d50dbdeba92d60f2304c54.1514736742.git.jpoimboe@redhat.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Meelis reported that his K8 Athlon64 emits MCE warnings when PTI is
enabled:
[Hardware Error]: Error Addr: 0x0000ffff81e000e0
[Hardware Error]: MC1 Error: L1 TLB multimatch.
[Hardware Error]: cache level: L1, tx: INSN
The address is in the entry area, which is mapped into kernel _AND_ user
space. That's special because we switch CR3 while we are executing
there.
User mapping:
0xffffffff81e00000-0xffffffff82000000 2M ro PSE GLB x pmd
Kernel mapping:
0xffffffff81000000-0xffffffff82000000 16M ro PSE x pmd
So the K8 is complaining that the TLB entries differ. They differ in the
GLB bit.
Drop the GLB bit when installing the user shared mapping.
Fixes: 6dc72c3cbca0 ("x86/mm/pti: Share entry text PMD")
Reported-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Meelis Roos <mroos@linux.ee>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/alpine.DEB.2.20.1801031407180.1957@nanos
|
|
AMD processors are not subject to the types of attacks that the kernel
page table isolation feature protects against. The AMD microarchitecture
does not allow memory references, including speculative references, that
access higher privileged data when running in a lesser privileged mode
when that access would result in a page fault.
Disable page table isolation by default on AMD processors by not setting
the X86_BUG_CPU_INSECURE feature, which controls whether X86_FEATURE_PTI
is set.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Borislav Petkov <bp@suse.de>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20171227054354.20369.94587.stgit@tlendack-t1.amdoffice.net
|
|
This really want's to be enabled by default. Users who know what they are
doing can disable it either in the config or on the kernel command line.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
|
|
The msm/kms driver should work even if there is no GPU device specified
in DT. Currently, we get a NULL dereference crash in adreno_load_gpu
since the driver assumes that priv->gpu_pdev is non-NULL.
Perform an additional check on priv->gpu_pdev before trying to retrieve
the msm_gpu pointer from it.
v2: Incorporate Jordan's comments:
- Simplify the check to share the same error message.
- Use dev_err_once() to avoid an error message every time we open the
drm device fd.
Fixes: eec874ce5ff1 (drm/msm/adreno: load gpu at probe/bind time)
Signed-off-by: Archit Taneja <architt@codeaurora.org>
Acked-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@gmail.com>
|
