| Age | Commit message (Collapse) | Author |
|---|
|
Add du node to r8a7744 SoC DT. Boards that want to enable the DU
need to specify the output topology.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
When commit 022bccb840b7 ("dts: arm64/sdm845: Add WCN3990 WLAN module
device node") was posted upstream no clocks were specified. However,
when the pack was picked into the Chrome OS kernel tree (allegedly
directly from the mailing list post) it had clock properties.
I presume that the clock should be there, so let's add it.
Fixes: 022bccb840b7 ("dts: arm64/sdm845: Add WCN3990 WLAN module device node")
Tested-by: Sibi Sankar <sibis@codeaurora.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
[bjorn: Add also the required iommus property]
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Add the clock measure device to the g12a SoC family
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Add the clock measure device to the axg SoC family
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Update I2C Device node compatible string to be appropriate.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Update I2C device node compatible string to be appropriate.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Change the SDMMC clock source to support a maximum frequency of 200 MHz
on Tegra194.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add CQE Support for Tegra186 and Tegra194 SDMMC4 controller
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add SDMMC initial pad offsets used by auto calibration process.
Add SDMMC fixed drive strengths for Tegra210, Tegra186 and
Tegra194 which are used when calibration timeouts.
Fixed drive strengths are based on Pre SI Analysis of the pads.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra Combined UART is the proper primary serial port on P2888,
so use it.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add nodes required for communication through the Tegra Combined UART.
This includes the AON HSP instance, addition of shared interrupts
for the TOP0 HSP instance, and finally the TCU node itself. Also
mark the HSP instances as compatible to tegra194-hsp, as the hardware
is not identical but is compatible to tegra186-hsp.
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Enable DFLL clock for Smaug board.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add CPU power rail regulator for Smaug board.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Enable DFLL clock for Jetson TX1 platform.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add pinmux for PWM-based DFLL support.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add CPU clocks for Tegra210.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add essential DFLL clock properties for Tegra210.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The GTA04 has a w2sg0004 or w2sg0084 gps chip. Not detectable
which one is mounted so use the compatibility entry for w2sg0004
for all which will work for both.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Required for completeness sake to be able to specify
a regulator for devices having a non-optional regulator
property. It corresponds to the "3V3" net in the
schematics.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There is one button and a notifier for incoming phone
calls/text messages for which we should wakeup from
suspend.
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
There's no need to use an external link when the file is already here.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Update binding document for MT7622 BPI-R64 and MT7629 reference board.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
As we fallback to use "mediatek,mt7623" for MT7623a, remove unused
root node property "mediatek,mt7623a" in the document.
Signed-off-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
On the Bananapi M3 and Cubietruck Plus, the DC input jacks are wired to
the ACIN pins, which is represented by the AC power supply. Both boards
have connectors for LiPo batteries, which are represented by the battery
power supply.
The H8 Homlet is a set-top box design. The DC input jack is wired to the
ACIN pins, but there are no battery connectors.
Enable these power supplies in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The Cubieboard4 has a Realtek RTL8211E ethernet PHY which uses RGMII to
talk to the MAC. The PHY is powered by 2 regulators: cldo1 for the PHY's
core logic and gpio1-ldo for I/O. The latter also powers the SoC side
pins. As there is no binding to model a second regulator supply for the
PHY, it is omitted. It is however properly modeled for the PIO.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The A80 Optimus has a Realtek RTL8211E ethernet PHY which uses RGMII to
talk to the MAC. The PHY is powered by 2 regulators: cldo1 for the PHY's
core logic and gpio1-ldo for I/O. The latter also powers the SoC side
pins. As there is no binding to model a second regulator supply for the
PHY, it is omitted. It is however properly modeled for the PIO.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The GMAC (gigabit ethernet controller) supports RGMII to connect to
the ethernet PHY, for gigabit network speeds.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The A80 has the same GMAC found on the A31 SoC.
Add a device node, and an alias for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The A80 has the same DWMAC hardware as on earlier Allwinner SoCs. The
accompanying GMAC clock register has been moved into the "System
Control" area.
Add a clock node for it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The Cubieboard 4 has the PMIC providing voltage to all the pin-bank
supply rails from its various regulator outputs. All pin-banks that
have supply rails are accounted for. PN pin-bank does not have a
supply rail.
Also remove any "regulator-always-on" properties from regulators that
were only marked to provide pin-bank power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The A80 Optimus has the PMIC providing voltage to all the pin-bank
supply rails from its various regulator outputs. All pin-banks that
have supply rails are accounted for. PN pin-bank does not have a
supply rail.
Also remove any "regulator-always-on" properties from regulators that
were only marked to provide pin-bank power.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The DC1SW output from the AXP809 is unused. Unused regulators should
still be listed so as to be considered to be fully constrained.
Fixes: aa4a27bc819e ("ARM: dts: sun9i: a80-optimus: Add AXP809 PMIC device node and regulators")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
This adds dt-binding documentation of cpu for Mediatek MT8183.
Signed-off-by: Erin Lo <erin.lo@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Fix apb, cbus, hiu and periph regions which are not aligned
with the documentation and the information provided by Amlogic
Fixes: 9c8c52f7cb4f ("arm64: dts: meson-g12a: add initial g12a s905d2 SoC DT support")
Cc: Jianxin Pan <jianxin.pan@amlogic.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The USB controllers need to be associated with their respective IOMMU
bank, so define this on the dwc3 nodes.
Also add dma-ranges to the qcom-dwc3 nodes to make the bus' DMA mask
propagate to the dwc3 controller instances.
Fixes: 4429e57567bb ("arm64: dts: sdm845: Add node for arm,mmu-500")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
With apps_smmu initializing the SMMU we must specify iommus property for
the sdhc controller.
Fixes: 4429e57567bb ("arm64: dts: sdm845: Add node for arm,mmu-500")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
Since all cpus in the big and little clusters, respectively, are in the
same frequency domain, use all of them for mitigation in the
cooling-map. We end up with two cooling devices - one each for the big
and little clusters.
Signed-off-by: Amit Kucheria <amit.kucheria@linaro.org>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
The databook clearly states that the MSI IRQ (msi_ctrl_int) is a level
triggered interrupt.
The msi_ctrl_int will be high for as long as any MSI status bit is set,
thus the IRQ type should be set to IRQ_TYPE_LEVEL_HIGH, causing the
IRQ handler to keep getting called, as long as any MSI status bit is set.
A git grep shows that ipq4019 is the only SoC using snps,dw-pcie that has
configured this IRQ incorrectly.
Not having the correct IRQ type defined will cause us to lose interrupts,
which in turn causes timeouts in the PCIe endpoint drivers.
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
The apcs node has #clock-cells = <0>, which means that those who
references it should specify 0 arguments.
The apcs reference in the cpu node incorrectly specifies an argument,
remove this bogus argument.
Fixes: 65afdf458360 ("arm64: dts: qcom: msm8916: Add CPU frequency scaling support")
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Amit Kucheria <amit.kucheria@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
The cpu_lp clock property is only needed when the CPUfreq driver
supports CPU cluster switching. But it was not a design for this driver
and it didn't handle that as well. So removing this property.
Cc: devicetree@vger.kernel.org
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Tegra124 cpufreq driver works only with DFLL clock, which is a
hardware-based frequency/voltage controller. The driver doesn't need to
control the regulator itself. Hence remove that.
Cc: devicetree@vger.kernel.org
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add Tegra210 support for DFLL clock.
Cc: devicetree@vger.kernel.org
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Add new properties to configure the DFLL PWM regulator support.
Cc: devicetree@vger.kernel.org
Signed-off-by: Peter De Schrijver <pdeschrijver@nvidia.com>
Signed-off-by: Joseph Lo <josephl@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Starting with commit 8947e396a829 ("Documentation: dt: mtd: replace
"nor-jedec" binding with "jedec, spi-nor"") we have "jedec,spi-nor"
binding indicating support for JEDEC identification.
Use it for all flashes that are supposed to support READ ID op according
to the datasheets.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The Libre Computer ALL-H3-CC H5 is one of the few boards that can have
its eMMC run at HS-DDR speed mode. Mark it as such.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
On these A64 devices, the DC input jacks are wired to the ACIN pins of
the PMIC, which is represented by the AC power supply. With the
exception of the Nanopi A64, all devices include LiPo batteries or have
connectors for them, which are represented by the battery power supply.
Enable these power supplies in the device tree.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Ensure the PCIe endpoint card reset that is toggled by the PCIe
controller itself is muxed correctly on the EspressoBin.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
One pin can be muxed as PCIe endpoint card reset.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
On Marvell Armada 3700 SoCs there are two USB2 UTMI PHYs. They are
both very similar but only one has OTG/charging capabilities.
Because there are USB host registers and PHY registers mixed in a
single area, a system controller is also created and referenced from
both the USB host node and the PHY node.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The specification splits the USB2 memory region into three sections:
1/ 0xD005E000-0xD005EFFF: USB2 Host Controller Registers
2/ 0xD005F000-0xD005F7FF: USB2 UTMI PHY Registers
3/ 0xD005F800-0xD005FFFF: USB2 Host Miscellaneous Registers
Section 1/ belongs to the USB2 node but section 2/ belongs to the UTMI
PHY node. Section 3/ can be accessed by both the USB controller and
the PHY because of the miscaellaneous nature of the registers inside
so a specific node will be created to cover the area and a handle to
it will be added in both the USB controller and the PHY node.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
