| Age | Commit message (Collapse) | Author |
|---|
|
The Broadcom Vulcan ARM64 processor uses the same I2C controller
present on the Broadcom XLP9xx/5xx MIPS processor family.
Updated the Kconfig by adding ARCH_VULCAN option.
Signed-off-by: Tanmay Jagdale <tanmay.jagdale@broadcom.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Enable the I2C core for this SoC.
Signed-off-by: Yakir Yang <ykk@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
DTK-1651 is a display pen-only tablet
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
mvebu fixes for 4.6 (part 1)
- fix USB adress register for Linksys Armada 388 based boards
- fix build warning in mvebu-mbus
* tag 'mvebu-fixes-4.6-1' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: Correct unit address for linksys
bus: mvebu-mbus: use %pa to print phys_addr_t
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The website handhelds.org has been down for a long time and is
likely never coming back online.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
ARM: pxa: fixes for v4.6
There is only a single fix for dma requestor lines initial
setup, triggered by dmaengine previous fix.
* tag 'pxa-fixes-v4.6' of https://github.com/rjarzmik/linux:
ARM: pxa: fix the number of DMA requestor lines
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps against v4.6-rc1. Mostly minor fixes for the newer
SoCs with few board fixes and a fix for a long time hwmod bug:
- Fix cpsw_emac0 link type for baltos-ir5221
- Fix interrupt type for TWD
- Fix edma memcpy channel allocation for am43x
- Fix am43x-epos sycntimer32k by using the correct assigned clock
- Fix interconnect barrier for dra7
- Fix a long time hwmod bug for updating sysconfig register properly
- Fix flakey booting on dm814x where USB reset needs a delay
And there is one minor change that is not strictly a fix, but is
good to have for proper hardware detection:
- Detect dra7 silicon revision 2.0 properly
* tag 'omap-for-v4.6/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am335x-baltos-ir5221: fix cpsw_emac0 link type
ARM: OMAP: Correct interrupt type for ARM TWD
ARM: DRA722: Add ID detect for Silicon Rev 2.0
ARM: dts: am43xx: fix edma memcpy channel allocation
ARM: dts: AM43x-epos: Fix clk parent for synctimer
ARM: OMAP2: Fix up interconnect barrier initialization for DRA7
ARM: OMAP2+: hwmod: Fix updating of sysconfig register
ARM: OMAP2+: Use srst_udelay for USB on dm814x
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch fixes condition whether the specified address ranges
overlap each other.
Fixes: 4b7f48d395a7 ("bus: uniphier-system-bus: add UniPhier System Bus driver")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
My intention was to ioremap a 4-byte register. Coincidentally enough,
sizeof(SZ_4) equals to SZ_4, but this code is weird anyway.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Check whether the DPLL is even enabled before readoing out the dividers
and trying to derive port_clock on CHV. We already did this on VLV.
Also remove the comment "MIPI" comment from the VLV code since we call
this function whenever the pipe is enabled.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-9-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
pgm_ratios in stored as a register value in pipe config, so let's dump
this one as hex as well.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-15-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
Use the proper refclock frequency (100MHz) when reading out the
current DSI clock on CHV.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-13-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
On VLV at least, the BIOS may leave the DSI PLL enabled in some wonky
state where it just refuses to lock. Simply disabling the PLL before
reconfiguring it is not enough to fix it, but power gating the PLL
prior to reconfiguring does work.
This happens on BYT FFRD8 when booting with HDMI connected so the DSI
display will not be lit up by the BIOS.
Also we can remove the code for BXT that disables the PLL before
enabling it again.
v2: s/vlv/intel/ since BXT made thing generic
v3: Remove the BXT disable PLL before enable trick
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-11-git-send-email-ville.syrjala@linux.intel.com
Acked-by: Jani Nikula <jani.nikula@intel.com>
|
|
All the values in the DSI PLL LFSR seed table fit into 9bits, so change
the type to u16 from u32 to save a bit of space.
drivers/gpu/drm/i915/i915.ko:
-.rodata 90824
+.rodata 90760
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458052809-23426-10-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
This patch fixes the issue introduced by the ext4 crypto fix in a same manner.
For F2FS, however, we flush the pending IOs and wait for a while to acquire free
memory.
Fixes: c9af28fdd4492 ("ext4 crypto: don't let data integrity writebacks fail with ENOMEM")
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
|
This patch synced with the below two ext4 crypto fixes together.
In 4.6-rc1, f2fs newly introduced accessing f_path.dentry which crashes
overlayfs. To fix, now we need to use file_dentry() to access that field.
Fixes: c0a37d487884 ("ext4: use file_dentry()")
Fixes: 9dd78d8c9a7b ("ext4: use dget_parent() in ext4_file_open()")
Cc: Miklos Szeredi <mszeredi@redhat.com>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
|
This patch updates fscrypto along with the below ext4 crypto change.
Fixes: 3d43bcfef5f0 ("ext4 crypto: use dget_parent() in ext4_d_revalidate()")
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Jaegeuk Kim <jaegeuk@kernel.org>
|
|
Enable the unclaimd register detection stuff on vlv/chv since we've now
fixed the known problems during suspend.
This reverts commit c81eeea6c14b212016104f4256c65f93ad230a86.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-11-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
|
|
DPINVGTT lives inside the disp2d power well so we can't frob it unless
we know the power well is active. Let's this stuff into
vlv_display_irq_reset() which is only called at the right times so that
we don't get unclaimed register access errors.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94164
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-10-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
|
|
The registers frobbed by vlv_init_display_clock_gating() libve inside
the disp2d power well, so frobbing them while the power well is down
results in unclaimed register access warning (and of course the values
won't stick). Let's do this setup after we know the power well is
enabled.
It's also worth noting that DSPCLK_GATE_D and CBR1_VLV lose their state
when the power well goes down, but fortunately the values we've been
writing are actually the reset defaults.
MI_ARB_VLV actually retains its value even if the power well was turned
off, we just can't access it while the power well is down.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94164
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-9-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
|
|
We expect vlv_display_irq_reset() to have been called prior to
vlv_display_irq_postinstall() so let's WARN if that isn't the case.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-8-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
|
|
Replace the hand rolled IMR/IER setup in vlv_display_irq_postinstall()
with GEN5_IRQ_INIT(). Also rename the iir_mask to enable_mask to avoid
consusion since we no longer deal with IIR here.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-7-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
|
|
For a bit of extra paranoia make sure the display irqs are all cleared
before we enabled them when turning on the power well. This should
really be the case already since the power well was off which resets
everything.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-6-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
|
|
Reshuffle the code a bit to move the vlv/chv display irq functions away
from the main irq hooks, next to the other sub (de,gt,etc.) hooks.
v2: Rebased due to changes in vlv_display_irq_reset()
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1460476604-2035-1-git-send-email-ville.syrjala@linux.intel.com
|
|
During runtime PM we'll be reinitializing interrupt support from the
ground up. However since the display power well will be off at that
time, well end up with a ton of unclaimed register accesses from the
display irq setup. Since we turned off the power well already before
runtime suspend, we've flagged display irqs as disabled during runtime
PM transitions. So we can just check that flag to see if we should do
skip display irqs during irq setup.
During driver load display irqs will be flagged as enabled since we've
turned on the power well already, however the power well code will have
skipped the display irq setup since irq support as a whole wasn't yet
enabled when the power well was enabled. So we'll want to do the display
irq setup in that case.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94164
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
|
|
The vlv/chv display irq setup was a bit of mess after I ran out of steam
when working on it last. Fix it up so that we just have a _reset() and
_postinstall() hooks for the display irqs, and use those consistently.
v2: Clear out pipestat_irq_mask[] and PIPE_FIFO_UNDERRUN_STATUS in
vlv_display_irq_reset() (Imre)
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1460476574-1921-1-git-send-email-ville.syrjala@linux.intel.com
|
|
No clue what this is supposed to achieve. I think it's been there since
the very beginning, so presumably some kind of kludge for very early
silicon. Let's just throw it out.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460382992-28728-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Imre Deak <imre.deak@intel.com>
|
|
The underruns we were seeing when enabling eDP port A on ILK seem to
have been caused by prematurely clearing the LP1+ watermark values when
disabling LP1+ watermarks. Now that the watermarks are handled
properly, we can rip out the underrun suppression around the port A
enable.
We still need to worry about the underruns on FDI when enabling
the eDP PLL. But as Bspec tells us, we can avoid that by a vblank
wait on the pipe driving FDI just prior to enabling the eDP PLL.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459536799-18109-4-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
|
|
to 2 pipes
Once again ILK is unhappy if we clear out the LP1+ watermark levels
outright, and instead we must disable the levels we don't want while
still leaving the actual programmed watermark levels intact.
Fixes underruns on the already enabled pipe when programming watermarks
while enabling the second pipe.
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Matt Roper <matthew.d.roper@intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=93787
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459536799-18109-3-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
|
|
Take a bigger hammer to the underrun suppression on ILK. Instead of
trying to suppress them at specific points in the modeset sequence just
silence them across the entire sequence. This gets rid of some underruns
at least on my ILK. Note that this changes SNB and IVB to follow the
same approach just to keep the code less convoluted. The difference is
that on those platforms we won't suppress CPU underruns for port A since
it doesn't seem to be necessary.
My ILK has port A eDP and two PCH HDMI ports, so I can't be sure this is
as effective on other PCH port types. Perhaps we still need some of
Daniel's extra vblank waits [2]?
I've still been able to trigger an underrun on the other pipe, but
fixing that perhaps needs the LP1+ disable trick I implemented here [1]
which never got merged.
A few details which hamper stress testing on my ILK are that sometimes
the PCH transcoder gets messed up and refuses to shut down, and sometimes
even the panel power sequencer apparently gets stuck on the always on
position.
[1] https://lists.freedesktop.org/archives/intel-gfx/2014-March/041317.html
[2] https://lists.freedesktop.org/archives/intel-gfx/2016-January/086397.html
v2: Add a note that we also get underruns when enabling PCH ports
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1459536799-18109-2-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Patrik Jakobsson <patrik.jakobsson@linux.intel.com>
|
|
Commit 254d4d111ee1 ("drm/exynos: Add dependency for G2D in Kconfig") made
the DRM_EXYNOS_G2D symbol to only be selectable if the s5p-g2d V4L2 driver
is not enabled, since both use the same HW IP block.
But added the dependency as depends on !VIDEO_SAMSUNG_S5P_G2D which isn't
correct since Kconfig expressions are not boolean but tristate. So it will
only evaluate to 'n' if VIDEO_SAMSUNG_S5P_G2D=y but it will evaluate to m
if VIDEO_SAMSUNG_S5P_G2D=m.
This means that both the V4L2 and DRM drivers can be enabled if the former
is enabled as a module, which is not what we want.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Rather than blindly waking up all forcewake domains on command
submission, we can teach each engine what is (or are) the correct
one to take.
On platforms with multiple forcewake domains like VLV, CHV, SKL
and BXT, this has the potential of lowering the GPU and CPU
power use and submission latency.
To implement it we add a function named
intel_uncore_forcewake_for_reg whose purpose is to query which
forcewake domains need to be taken to read or write a specific
register with raw mmio accessors.
These enables the execlists engine setup to query which
forcewake domains are relevant per engine on the currently
running platform.
v2:
* Kerneldoc.
* Split from intel_uncore.c macro extraction, WARN_ON,
no warns on old platforms. (Chris Wilson)
v3:
* Single domain per engine, mention all registers,
bi-directional function and a new name, fix handling
of gen6 and gen7 writes. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460468251-14069-1-git-send-email-tvrtko.ursulin@linux.intel.com
|
|
Chris Wilson points out that we can remove them from the array
since they are always written to with raw accessors.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
Knowledge of which register per platform belonds in which
forcewake domain was embedded in the MMIO accessors themselves.
Extract it into standalone macros so they can be used from
new code in the following patches.
This causes GCC to compile some of the MMIO accessors slightly
differently and grows the code a tiny amount. But none of the
growth is on the fast-path so it does not matter hugely.
Affected sizes before:
00000000000026f0 00000000000001a5 t gen6_read16
0000000000002390 00000000000001a5 t gen6_read32
00000000000028a0 00000000000001a5 t gen6_read64
00000000000061d0 000000000000019e t gen8_write16
0000000000006510 000000000000019d t gen8_write32
0000000000006370 000000000000019d t gen8_write64
00000000000021f0 000000000000019d t gen8_write8
Affected sizes after:
0000000000002840 00000000000001aa t gen6_read16
00000000000024e0 00000000000001a9 t gen6_read32
00000000000029f0 00000000000001a9 t gen6_read64
0000000000004f20 00000000000001b5 t gen8_write16
0000000000004ba0 00000000000001b4 t gen8_write32
00000000000050e0 00000000000001b4 t gen8_write64
0000000000004d60 00000000000001b4 t gen8_write8
Other MMIO accessors are not affected in size.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
The "ret = regmap_write()" assignment was missing so this error message
is never printed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
We accidentally return success instead of a negative error code here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Commit 1feafd3afd294b03dbbedb8e8f94e0c4db526f10 ("drm/exynos: add
exynos5420 support for fimd") add support for Exynos 5420 SoC, but it
broke enabling display clock feature because of incorrect condition
check. This patch fixes it, so display is working again on platforms
requiring display clock control (i.e. Exynos5250-based SNOW platform).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Fbdev code should be compiled only if CONFIG_DRM_FBDEV_EMULATION option
is enabled. The patch fixes exynos-drm code trying to manipulate
fbdev data which is not initialized in case CONFIG_DRM_FBDEV_EMULATION
is disabled.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
exynos_plane_mode_set should use adjusted_mode from the same atomic state as
plane state. Otherwise it will result in incorrect behavior in case
crtc mode changes.
The patch fixes bug with black console framebuffer in case of command mode
panels.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
gcc-6 warns about a pointless loop in exynos_drm_subdrv_open:
drivers/gpu/drm/exynos/exynos_drm_core.c: In function 'exynos_drm_subdrv_open':
drivers/gpu/drm/exynos/exynos_drm_core.c:104:199: error: self-comparison always evaluates to false [-Werror=tautological-compare]
list_for_each_entry_reverse(subdrv, &subdrv->list, list) {
Here, the list_for_each_entry_reverse immediately terminates because
the subdrv pointer is compared to itself as the loop end condition.
If we were to take the current subdrv pointer as the start of the
list (as we would do if list_for_each_entry_reverse() was not a macro),
we would iterate backwards over the &exynos_drm_subdrv_list anchor,
which would be even worse.
Instead, we need to use list_for_each_entry_continue_reverse()
to go back over each subdrv that was successfully opened until
the first entry.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
A non-privileged user can create a netlink socket with the same port_id as
used by an existing open nl80211 netlink socket (e.g. as used by a hostapd
process) with a different protocol number.
Closing this socket will then lead to the notification going to nl80211's
socket release notification handler, and possibly cause an action such as
removing a virtual interface.
Fix this issue by checking that the netlink protocol is NETLINK_GENERIC.
Since generic netlink has no notifier chain of its own, we can't fix the
problem more generically.
Fixes: 026331c4d9b5 ("cfg80211/mac80211: allow registering for and sending action frames")
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Ivanov <dima@ubnt.com>
[rewrite commit message]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
On platforms with multiple forcewake domains it seems more efficient
to request all desired ones and then to wait for acks to avoid
needlessly serializing on each domain.
v2: Rebase.
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1460045074-1006-1-git-send-email-tvrtko.ursulin@linux.intel.com
|
|
As the vast majority of users do not use the domain id variable,
we can eliminate it from the iterator and also change the latter
using the same principle as was recently done for for_each_engine.
For a couple of callers which do need the domain mask, store it
in the domain array (which already has the domain id), then both
can be retrieved thence.
Result is clearer code and smaller generated binary, especially
in the tight fw get/put loops. Also, relationship between domain
id and mask is no longer assumed in the macro.
v2: Improve grammar in the commit message and rename the
iterator to for_each_fw_domain_masked for consistency.
(Dave Gordon)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
|
|
Because it is based on jiffies, current implementation releases the
forcewake at any time between straight away and between 1ms and 10ms,
depending on the kernel configuration (CONFIG_HZ).
This is probably not what has been desired, since the dynamics of keeping
parts of the GPU awake should not be correlated with this kernel
configuration parameter.
Change the auto-release mechanism to use hrtimers and set the timeout to
1ms with a 1ms of slack. This should make the GPU power consistent
across kernel configs, and timer slack should enable some timer coalescing
where multiple force-wake domains exist, or with unrelated timers.
For GlBench/T-Rex this decreases the number of forcewake releases from
~480 to ~300 per second, and for a heavy combined OGL/OCL test from
~670 to ~360 (HZ=1000 kernel).
Even though this reduction can be attributed to the average release period
extending from 0-1ms to 1-2ms, as discussed above, it will make the
forcewake timeout consistent for different CONFIG_HZ values.
Real life measurements with the above workload has shown that, with this
patch, both manage to auto-release the forcewake between 2-4 times per
10ms, even though the number of forcewake gets is dramatically different.
T-Rex requests between 5-10 explicit gets and 5-10 implict gets in each
10ms period, while the OGL/OCL test requests 250 and 380 times in the same
period.
The two data points together suggest that the nature of the forwake
accesses is bursty and that further changes and potential timeout
extensions, or moving the start of timeout from the first to the last
automatic forcewake grab, should be carefully measured for power and
performance effects.
v2:
* Commit spelling. (Dave Gordon)
* More discussion on numbers in the commit. (Chris Wilson)
Signed-off-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
|
|
No need to confuse userspace like this.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459331485-28376-8-git-send-email-daniel.vetter@ffwll.ch
|
|
Only really needed for fbdev emulation at 8bpp. And bochs doesn't do
that. And either way bochs only does 32bit rgb, so this is all pretty
much wasted dead code.
The only consideration is that we need to not set up any gamma size
either.
Cc: Gerd Hoffmann <kraxel@redhat.com>
Cc: Dave Airlie <airlied@redhat.com>
Reviewed-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1459331485-28376-5-git-send-email-daniel.vetter@ffwll.ch
|
|
__drm_atomic_helper_plane_destroy_state calls
drm_framebuffer_unreference, which means that if drm_framebuffer_free
is called before plane->destroy freed memory will be accessed.
A similar case happens for the blob list, which was freed before the
crtc state was, resulting in the unreference_blob from crtc_destroy_state
pointing to garbage memory causing another opportunity for a GPF.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1458657734-21866-1-git-send-email-maarten.lankhorst@linux.intel.com
|
|
We've had problems on several occasions with using the panel type
from the VBT block 40. Usually it seems to be 2, which often
doesn't give us the correct timings for the panel. After some
more digging I found a way to get a panel type via the OpRegion
SWSCI GBDA "Get Panel Details" method. Let's try to use it.
The spec has this to say about the output:
"Bits [15:8] - Panel Type
Bits contain the panel type user setting from CMOS
00h = Not Valid, use default Panel Type & Timings from VBT
01h - 0Fh = Panel Number"
Another version of the spec lists the valid range as 1-16, which makes
more sense since VBT supports 16 panels. Based on actual results
from Rob's G45, 1-16 is what we need to accept.
The other bits in the output don't look relevant for the problem at
hand.
The input is specified as:
"Bits [31:4] - Reserved
Reserved (must be zero)
Bits [3:0] - Panel Number
These bits contain the sequential index of Panel, starting at 0 and
counting upwards from the first integrated Internal Flat-Panel Display
Encoder present, and then from the first external Display Encoder
(e.g., S/DVO-B then S/DVO-C) which supports Internal Flat-Panels.
0h - 0Fh = Panel number"
For now I've just hardcoded the input panel number as 0. That would seem
like a decent choise for LVDS. Not so sure about eDP when port != A.
v2: Accept values 1-16
Filter out bogus results in opregion code (Jani)
Add debug logging for all the different branches (Jani)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rob Kramer <rob@solution-space.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=94825
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1460359431-11003-1-git-send-email-ville.syrjala@linux.intel.com
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Rob Kramer <rob@solution-space.com>
|
|
Store the extracted panel_type under dev_priv.vbt instead of keeping
around a static variable for it.
Cc: Rob Kramer <rob@solution-space.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
|
|
VBT can only contain 16 panel entries, indexed with the panel_type.
To play it safe we should reject panel_type > 0xf, so that we don't
read past the valid data.
v2: Add debug logging (Jani)
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rob Kramer <rob@solution-space.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com> (v1)
Link: http://patchwork.freedesktop.org/patch/msgid/1460359329-10817-1-git-send-email-ville.syrjala@linux.intel.com
|
