| Age | Commit message (Collapse) | Author |
|---|
|
The GPIO core provides a handy GPIO_LOOKUP() macro to populate a struct
gpiod_lookup array without having to spell out attribute names (but
still avoid breakage when attributes within the struct are rearranged
or added).
The axp288_adc.c driver uses a similar macro to populate a struct
iio_map array. Make it available to others.
Cc: Jacob Pan <jacob.jun.pan@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-fixes
Second batch of fixes intended for 4.15.
* One fix in rate-scaling;
* One fix for the TX queue hang detection for AP/GO modes;
* Fix the TX queue hang timeout used in monitor interfaces;
* Fix packet injection;
* Remove a wrong error message when dumping PCI registers;
* Fix race condition with RF-kill;
|
|
The platform_get_irq() function returns negative if an error occurs.
zero or positive number on success. platform_get_irq() error checking
for zero is not correct.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
The I2C device ID table entries have the .driver_data field set, but they
are not used in the driver so weren't set in the OF device table entries.
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Update the doc as the SAR ADC modules doesn't require "sana" clock.
Singed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The "sana" clock is not used at SAR ADC module in Amlogic Meson SoC,
it is irrelevant for the SAR ADC.
Signed-off-by: Xingyu Chen <xingyu.chen@amlogic.com>
Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The ADC driver can trigger on either the timer or the lptim
trigger, but it only uses a Kconfig 'select' statement
to ensure that the first of the two is present. When the lptim
trigger is enabled as a loadable module, and the adc driver
is built-in, we now get a link error:
drivers/iio/adc/stm32-adc.o: In function `stm32_adc_get_trig_extsel':
stm32-adc.c:(.text+0x4e0): undefined reference to `is_stm32_lptim_trigger'
We could use a second 'select' statement and always have both
trigger drivers enabled when the adc driver is, but it seems that
the lptimer trigger was intentionally left optional, so it seems
better to keep it that way.
This adds a hack to use 'IS_REACHABLE()' rather than 'IS_ENABLED()',
which avoids the link error, but instead leads to the lptimer trigger
not being used in the broken configuration. I've added a runtime
warning for this case to help users figure out what they did wrong
if this should ever be done by accident.
Fixes: f0b638a7f6db ("iio: adc: stm32: add support for lptimer triggers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
As per ABI temperature should be in milli Celsius after scaling,
not Celsius
Note on stable cc. This driver is breaking the standard IIO
ABI. (JC)
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Fix build errors in kernel-doc notation. Symbols that end in '_'
have a special meaning, but adding a '*' makes them OK.
../drivers/iio/industrialio-core.c:635: ERROR: Unknown target name: "iio_val".
../drivers/iio/industrialio-core.c:642: ERROR: Unknown target name: "iio_val".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The Meson GXBB and newer SoCs have a few more registers than the older
Meson8 and Meson8b SoCs.
Use a separate regmap config to limit the older SoCs to the DELTA_10
register.
Fixes: 6c76ed31cd05 ("iio: adc: meson-saradc: add Meson8b SoC compatibility")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Meson8 and Meson8b do not have the MESON_SAR_ADC_REG11 register. The
bandgap setting for these SoCs is configured in the
MESON_SAR_ADC_DELTA_10 register instead.
Make the driver aware of this difference and use the correct bandgap
register depending on the SoC.
This has worked fine on Meson8 and Meson8b because the bootloader is
already initializing the bandgap setting.
Fixes: 6c76ed31cd05 ("iio: adc: meson-saradc: add Meson8b SoC compatibility")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Meson8 and Meson8b SoCs use the the SAR ADC gate clock provided by the
MESON_SAR_ADC_REG3 register within the SAR ADC register area.
According to the datasheet (and the existing MESON_SAR_ADC_REG3_CLK_EN
definition) the gate is on bit 30.
The fls() function returns the last set bit, which is "bit index + 1"
(fls(MESON_SAR_ADC_REG3_CLK_EN) returns 31). Fix this by switching to
__ffs() which returns the first set bit, which is bit 30 in our case.
This off by one error results in the ADC not being usable on devices
where the bootloader did not enable the clock.
Fixes: 3adbf3427330 ("iio: adc: add a driver for the SAR ADC found in Amlogic Meson SoCs")
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The commit 0f0796509c07
("iio: remove gpio interrupt probing from drivers that use a single interrupt")
removed custom IRQ assignment for the drivers which are enumerated via
ACPI or OF. Unfortunately, some ACPI tables have IRQ line defined as
GpioIo() resource and thus automatic IRQ allocation will fail.
Partially revert the commit 0f0796509c07 to restore original behaviour.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Function platform_get_irq_byname() returns a negative error code on
failure, and a zero or positive number on success. However, in function
cpcap_adc_probe(), positive IRQ numbers are also taken as error cases.
Use "if (ddata->irq < 0)" instead of "if (!ddata->irq)" to validate the
return value of platform_get_irq_byname().
Signed-off-by: Pan Bian <bianpan2016@163.com>
Fixes: 25ec249632d50 ("iio: adc: cpcap: Add minimal support for CPCAP PMIC ADC")
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Pointer pdata is being assigned but it is never being used, hence
it is redundant and can be removed. Cleans up clang warning:
drivers/iio/accel/st_accel_core.c:952:3: warning: Value stored to 'pdata'
is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This adds an ACPI table to the driver and the ACPI ID of the sensor
on the tablet.
Signed-off-by: Luke Ross <luke@lukeross.name>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
add support for STMicroelectronics UVIS25 uv sensor
http://www.st.com/resource/en/datasheet/uvis25.pdf
- continuos mode support
- i2c support
- spi support
- trigger mode support
- system PM support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Michael Hennerich <Michael.Hennerich@analog.com>
Cc: Andreas Klinger <ak@it-klinger.de>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The ASPEED SoC must deassert a reset in order to use the ADC peripheral.
The device tree bindings are updated to document the resets phandle, and
the example is updated to match what is expected for both the reset and
clock phandle. Note that the bindings should have always had the reset
controller, as the hardware is unusable without it.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The Maxim MAX30105 part adds a third LED (green) and uses a multi-LED
measuring mode producing three measurements
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Current code assumes always 2 measurements (6 bytes) have to be copied,
prepare for more flexibility
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Move the programming of the mode setting from init() to
buffer_postenable()
Split out a separate function to
only update the power/shutdown bit
This changes permits to more easily implement different
modes of measurements in further patches
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Chip must not be in shutdown for reading temperature, so briefly leave
shutdown if buffer is not already running
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Signed-off-by: Peter Meerwald-Stalder <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Table 4 of the datasheet specifies the mode control, these are not
individual bits; add multi LED mode
Add multi-LED mode and fix MODE_MASK (3 bits wide, not 2)
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
STM32H7 ADC channels can be configured either as single ended or
differential with 'st,adc-channels' or 'st,adc-diff-channels'
(positive and negative input pair: <vinp vinn>, ...).
Differential channels have different offset and scale, from spec:
raw value = (full_scale / 2) * (1 + (vinp - vinn) / vref).
Add offset attribute.
Differential channels are selected by DIFSEL register. Negative
inputs must be added to pre-selected channels as well (PCSEL).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Remove const array that defines channels. Build channels definition
at probe time, when initializing channels (only for requested ones).
This will ease adding differential channels support.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
STM32H7 ADC channels may be configured either as single-ended or
differential.
Add 'st,adc-diff-channels' property to support differential channels.
Differential channels are defined as a pair of positive and negative
inputs: vinp & vinn.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Reducing shunt and bus voltage range improves the accuracy, so allow
altering the default settings.
Both settings are exposed as gain values. While for the shunt voltage
this is straightforward, the bus range settings of 32V (default) and 16V
are mapped to gain values of 1 resp. 2, to provide a uniform API to
userspace.
As the gain settings are incorporated into the raw values by the sensor
itself, adjusting of the scale attributes is not necessary.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
While the config uses the physical value corresponding to the LSB
for both the power and the bus voltage register, the shunt voltage is
specified as parts of 1 mV. Use the LSB physical value for all registers.
No functional change.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Lower bits of the INA219/220 bus voltage register are conversion
status flags, properly shift the value.
When reading via IIO buffer, the value is passed on unaltered,
shifting is the responsibility of the user.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Since i2c_unregister_device() became NULL-aware we may remove duplicate
NULL check.
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: linux-iio@vger.kernel.org
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
* Add a jump target so that a call of the function "mutex_unlock" is stored
only twice in this function implementation.
* Replace two calls by goto statements.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
* Add a jump target so that a call of the function "mutex_unlock" is stored
only twice in this function implementation.
* Replace two calls by goto statements.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add new ACPI ID for ak9911 as had been found on prototype board.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add new ACPI ID for sx9500 as had been found on prototype board.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Rename structs holding event configuration registers
to more appropriate names. This naming is consistent
with the event config register names given in the
mma845x and fxls8471 datasheets.
Signed-off-by: Harinath Nampally <harinath922@gmail.com>
Acked-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Rename time step look up struct to generic name
as the values in the look table are same for all
the other events like pulse, transient etc.
Signed-off-by: Harinath Nampally <harinath922@gmail.com>
Acked-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Driver for 20-bit ALS and UV B sensor with I2C interface exposing
the following API:
in_uvindex_input
in_illuminance_raw
in_illuminance_scale
in_illuminance_scale_available
in_intensity_uv_raw
in_intensity_uv_scale
in_intensity_uv_scale_available
integration_time
integration_time_available
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1397962
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Fix gcc warnings about variable 'ec_device' being set but not used
in these files:
common/cros_ec_sensors/cros_ec_sensors.c:194:25
light/cros_ec_light_prox.c:184:25
Signed-off-by: Paolo Cretaro <paolocretaro@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Need to acknowledge DRDY irq in direct mode/ software
triggered mode. Otherwise, on the next conversion, overrun
flag will be raised, which is not a correct state.
This doesn't affect the functionality, but will generate
possible incorrect overrun reports.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
