| Age | Commit message (Collapse) | Author |
|---|
|
By removing the PCI device reference from the structure and passing it
as parameters to the interested functions, we can make quark_pci_info
const.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the VF NIC is opened, the synthetic NIC's carrier state is set to
off. This tells the host to transitions data path to the VF device. But
if startup script or user manipulates the admin state of the netvsc
device directly for example:
# ifconfig eth0 down
# ifconfig eth0 up
Then the carrier state of the synthetic NIC would be on, even though the
data path was still over the VF NIC. This patch sets the carrier state
of synthetic NIC with consideration of the related VF state.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We simply use rndis_device->link_state in the netdev_dbg. The variable,
link_state from struct netvsc_device_info, is not used anywhere else.
Signed-off-by: Haiyang Zhang <haiyangz@microsoft.com>
Reviewed-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This structure member is hidden behind CONFIG_SYSFS, and we
get a build error when that is disabled:
drivers/net/hyperv/netvsc_drv.c: In function 'netvsc_set_channels':
drivers/net/hyperv/netvsc_drv.c:754:49: error: 'struct net_device' has no member named 'num_rx_queues'; did you mean 'num_tx_queues'?
drivers/net/hyperv/netvsc_drv.c: In function 'netvsc_set_rxfh':
drivers/net/hyperv/netvsc_drv.c:1181:25: error: 'struct net_device' has no member named 'num_rx_queues'; did you mean 'num_tx_queues'?
As the value is only set once to the argument of alloc_netdev_mq(),
we can compare against that constant directly.
Fixes: ff4a44199012 ("netvsc: allow get/set of RSS indirection table")
Fixes: 2b01888d1b45 ("netvsc: allow more flexible setting of number of channels")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The per netns loopback_dev->ip6_ptr is unregistered and set to
NULL when its mtu is set to smaller than IPV6_MIN_MTU, this
leads to that we could set rt->rt6i_idev NULL after a
rt6_uncached_list_flush_dev() and then crash after another
call.
In this case we should just bring its inet6_dev down, rather
than unregistering it, at least prior to commit 176c39af29bc
("netns: fix addrconf_ifdown kernel panic") we always
override the case for loopback.
Thanks a lot to Andrey for finding a reliable reproducer.
Fixes: 176c39af29bc ("netns: fix addrconf_ifdown kernel panic")
Reported-by: Andrey Konovalov <andreyknvl@google.com>
Cc: Andrey Konovalov <andreyknvl@google.com>
Cc: Daniel Lezcano <dlezcano@fr.ibm.com>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tracex5_kern.c build failed with the following error message:
../samples/bpf/tracex5_kern.c:12:10: fatal error: 'syscall_nrs.h' file not found
#include "syscall_nrs.h"
The generated file syscall_nrs.h is put in build/samples/bpf directory,
but this directory is not in include path, hence build failed.
The fix is to add $(obj) into the clang compilation path.
Signed-off-by: Yonghong Song <yhs@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Sowmini Varadhan says:
====================
rds: tcp: fixes
Patch1 is a bug fix for correct reconnect when a connection
is restarted. Patch 2 accelerates cleanup by setting linger
to 1 and sending a RST to the peer.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If we are unloading the rds_tcp module, we can set linger to 1
and drop pending packets to accelerate reconnect. The peer will
end up resetting the connection based on new generation numbers
of the new incarnation, so hanging on to unsent TCP packets via
linger is mostly pointless in this case.
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Jenny Xu <jenny.x.xu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RDS handshake ping probe added by commit 5916e2c1554f
("RDS: TCP: Enable multipath RDS for TCP") is sent from rds_sendmsg()
before the first data packet is sent to a peer. If the conversation
is not bidirectional (i.e., one side is always passive and never
invokes rds_sendmsg()) and the passive side restarts its rds_tcp
module, a new HS ping probe needs to be sent, so that the number
of paths can be re-established.
This patch achieves that by sending a HS ping probe from
rds_tcp_accept_one() when c_npaths is 0 (i.e., we have not done
a handshake probe with this peer yet).
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Tested-by: Jenny Xu <jenny.x.xu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The update to ibmvnic_init to allow an EAGAIN return code broke
the calling of ibmvnic_init from ibmvnic_probe. The code now
will return from this point in the probe routine if anything
other than EAGAIN is returned. The check should be to see if rc
is non-zero and not equal to EAGAIN.
Without this fix, the vNIC driver can return 0 (success) from
its probe routine due to ibmvnic_init returning zero, but before
completing the probe process and registering with the netdev layer.
Fixes: 6a2fb0e99f9c (ibmvnic: driver initialization for kdump/kexec)
Signed-off-by: Nathan Fontenot <nfont@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Thomas Falcon says:
====================
ibmvnic: Correct long-term-mapped buffer error handling
This patch set fixes the error-handling of long-term-mapped buffers
during adapter initialization and reset. The first patch fixes a bug
in an incorrectly defined descriptor that was keeping the return
codes from the VIO server from being properly checked. The second patch
fixes and cleans up the error-handling implementation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch stores the return code of the REQUEST_MAP_RSP sub-CRQ command
in the private data structure, where it can be later checked during
device open or a reset.
In the case of a reset, the mapping request to the vNIC Server may fail,
especially in the case of a partition migration. The driver attempts to
handle this by re-allocating the buffer and re-sending the mapping request.
The original error handling implementation was removed. The separate
function handling the REQUEST_MAP response message was also removed,
since it is now simple enough to be handled in the ibmvnic_handle_crq
function.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reserved area should be eight bytes in length instead of four.
As a result, the return codes in the REQUEST_MAP_RSP descriptors
were not being properly handled.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vladislav Yasevich says:
====================
macvlan: Fix some issues with changing mac addresses
There are some issues in macvlan wrt to changing it's mac address.
* An error is returned in the specified address is the same as an already
assigned address.
* In passthru mode, the mac address of the macvlan device doesn't change.
* After changing the mac address of a passthru macvlan and then removing it,
the mac address of the physical device remains changed.
This patch series attempts to resolve these issues.
V2: Address a small issue in p4 where we save the address from the lowerdev
(from girish.moodalbail@oracle.com)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Passthru macvlans directly change the mac address of the lower
level device. That's OK, but after the macvlan is deleted,
the lower device is left with changed address and one needs to
reboot to bring back the origina HW addresses.
This scenario is actually quite common with passthru macvtap devices.
This patch attempts to solve this, by storing the mac address
of the lower device in macvlan_port structure and keeping track of
it through the changes.
After this patch, any changes to the lower device mac address
done trough the macvlan device, will be reverted back. Any
changs done directly to the lower device mac address will be kept.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert the port passthru boolean into flags with accesor functions.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a lower device of the passthru macvlan changes it's address,
passthru macvlan is supposed to change it's own address as well.
However, that doesn't happen correctly because the check in
macvlan_addr_busy() will catch the fact that the lower level
(port) mac address is the same as the address we are trying to
assign to the macvlan, and return an error. As a reasult,
the address of the passthru macvlan device is never changed.
The same thing happens when the user attempts to change the
mac address of the passthru macvlan.
The simple solution appers to be to not check against
the lower device in case of passthru macvlan device, since
the 2 addresses are _supposed_ to be the same.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The user currently gets an EBUSY error when attempting to set
the mac address on a macvlan device to the same value.
This should really be a no-op as nothing changes. Catch
the condition and return early.
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a flag to indicate if a queue is rate-limited. Test the flag in
NAPI poll handler and avoid rescheduling the queue if true, otherwise
we risk locking up the host. The rescheduling will be done in the
timer callback function.
Reported-by: Jean-Louis Dupond <jean-louis@dupond.be>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Tested-by: Jean-Louis Dupond <jean-louis@dupond.be>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are number of problems with configuration peer
network device in absence of IFLA_VETH_PEER attributes
where attributes for main network device shared with
peer.
First it is not feasible to configure both network
devices with same MAC address since this makes
communication in such configuration problematic.
This case can be reproduced with following sequence:
# ip link add address 02:11:22:33:44:55 type veth
# ip li sh
...
26: veth0@veth1: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc \
noop state DOWN mode DEFAULT qlen 1000
link/ether 00:11:22:33:44:55 brd ff:ff:ff:ff:ff:ff
27: veth1@veth0: <BROADCAST,MULTICAST,M-DOWN> mtu 1500 qdisc \
noop state DOWN mode DEFAULT qlen 1000
link/ether 00:11:22:33:44:55 brd ff:ff:ff:ff:ff:ff
Second it is not possible to register both main and
peer network devices with same name, that happens
when name for main interface is given with IFLA_IFNAME
and same attribute reused for peer.
This case can be reproduced with following sequence:
# ip link add dev veth1a type veth
RTNETLINK answers: File exists
To fix both of the cases check if corresponding netlink
attributes are taken from peer_tb when valid or
name based on rtnl ops kind and random address is used.
Signed-off-by: Serhey Popovych <serhe.popovych@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
cpsw driver tries to get macid for am43xx SoCs using the compatible
ti,am4372. But not all variants of am43x uses this complatible like
epos evm uses ti,am438x. So use a generic compatible ti,am43 to get
macid for all am43 based platforms.
Reviewed-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently in both ipv4 and ipv6 code path, the ack packet received when
sk at TCP_NEW_SYN_RECV state is not filtered by socket filter or cgroup
filter since it is handled from tcp_child_process and never reaches the
tcp_filter inside tcp_v4_rcv or tcp_v6_rcv. Adding a tcp_filter hooks
here can make sure all the ingress tcp packet can be correctly filtered.
Signed-off-by: Chenbo Feng <fengc@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The memcpy annotation triggers for a fixed-length buffer copy:
In file included from /git/arm-soc/arch/arm64/include/asm/processor.h:30:0,
from /git/arm-soc/arch/arm64/include/asm/spinlock.h:21,
from /git/arm-soc/include/linux/spinlock.h:87,
from /git/arm-soc/include/linux/seqlock.h:35,
from /git/arm-soc/include/linux/time.h:5,
from /git/arm-soc/include/linux/stat.h:21,
from /git/arm-soc/include/linux/module.h:10,
from /git/arm-soc/drivers/net/phy/smsc.c:20:
In function 'memcpy',
inlined from 'smsc_get_strings' at /git/arm-soc/drivers/net/phy/smsc.c:166:3:
/git/arm-soc/include/linux/string.h:309:4: error: call to '__read_overflow2' declared with attribute error: detected read beyond size of object passed as 2nd parameter
Using strncpy instead of memcpy should do the right thing here.
Fixes: 030a89028db0 ("net: phy: smsc: Implement PHY statistics")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 242d3a49a2a1 ("ipv6: reorder ip6_route_dev_notifier after ipv6_dev_notf")
I assumed NETDEV_REGISTER and NETDEV_UNREGISTER are paired,
unfortunately, as reported by jeffy, netdev_wait_allrefs()
could rebroadcast NETDEV_UNREGISTER event until all refs are
gone.
We have to add an additional check to avoid this corner case.
For netdev_wait_allrefs() dev->reg_state is NETREG_UNREGISTERED,
for dev_change_net_namespace(), dev->reg_state is
NETREG_REGISTERED. So check for dev->reg_state != NETREG_UNREGISTERED.
Fixes: 242d3a49a2a1 ("ipv6: reorder ip6_route_dev_notifier after ipv6_dev_notf")
Reported-by: jeffy <jeffy.chen@rock-chips.com>
Cc: David Ahern <dsahern@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The commit ("net/phy: micrel: Add workaround for bad autoneg") fixes an
autoneg failure case by resetting the hardware. This turns off
intterupts. Things will work themselves out if the phy polls, as it will
figure out it's state during a poll. However if the phy uses only
intterupts, the phy will stall, since interrupts are off. This patch
fixes the issue by calling config_intr after resetting the phy.
Fixes: d2fd719bcb0e ("net/phy: micrel: Add workaround for bad autoneg ")
Signed-off-by: Zach Brown <zach.brown@ni.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use Mellanox device ID definitions in the driver's mlx5 ID table so tools
such as 'grep' and 'cscope' can be used to help find correlated material
(such as INTx Masking quirks: d76d2fe05fd PCI: Convert Mellanox broken
INTx quirks to be for listed devices only).
No functional change intended.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only compile-tested - I don't have the hardware.
>From code inspection, octeon_pci_write_core_mem() appears to be safe wrt
unaligned source. In any case, u8 fbuf[] was not guaranteed to be aligned
anyway.
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: Felix Manlunas <felix.manlunas@cavium.com>
CC: Prasad Kanneganti <prasad.kanneganti@cavium.com>
CC: Derek Chickles <derek.chickles@cavium.com>
CC: David Miller <davem@davemloft.net>
CC: netdev@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Acked-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TF is handled a bit differently for syscall and sysret, compared
to the other instructions: TF is checked after the instruction completes,
so that the OS can disable #DB at a syscall by adding TF to FMASK.
When the sysret is executed the #DB is taken "as if" the syscall insn
just completed.
KVM emulates syscall so that it can trap 32-bit syscall on Intel processors.
Fix the behavior, otherwise you could get #DB on a user stack which is not
nice. This does not affect Linux guests, as they use an IST or task gate
for #DB.
This fixes CVE-2017-7518.
Cc: stable@vger.kernel.org
Reported-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvms390/linux
KVM: s390: fix shadow table handling for nested guests
Some odd-ball cases (real-space designation ASCEs) are handled wrong
for the shadow page tables. Fix it.
|
|
ath.git patches for 4.13. Major changes:
wil6210
* add low level RF sector interface via nl80211 vendor commands
* add module parameter ftm_mode to load separate firmware for factory
testing
* support devices with different PCIe bar size
* add support for PCIe D3hot in system suspend
* remove ioctl interface which should not be in a wireless driver
ath10k
* go back to using dma_alloc_coherent() for firmware scratch memory
* add per chain RSSI reporting
|
|
The offending commit pushed fwd the field by two bits but
didn't increment the offset, fix that. Currently, no damage
was done b/c this is just a field name, but lets have it right.
Fixes: f32f5bd2eb7e ('net/mlx5: Configure cache line size for start and end padding')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This callback further invokes the mlxfw module to flash the new
firmware file to the device.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This callback further invokes the mlxfw module to flash the new
firmware file to the device.
As the firmware flash process takes about 20 seconds and ethtool
takes the rtnl lock during the flash_device callback, we release
the rtnl lock at the beginning of the flash process and take it
again before leaving the callback.
This way, rtnl is not held during the process. To make sure the
device does not get deleted while being flashed, we take a
reference to it before releasing rtnl lock.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add mlx5 implementation for the ones defined by the mlxfw
shared module to be used while flashing the device firmware.
The callbacks do their job through the MCQI, MCC and MCDA registers.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
To be used by the mlx5 callbacks exposed to the mlxfw module.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Enhance MCAM to allow the driver to query which access regs are
supported. For now, expose the regs needed for FW flashing.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
MCC (Management Component Control) allows to control a firmware
component update.
MCDA (Management Component Data Access) allows to read and write
a firmware component.
MCQI (Management Component Query Information) allows to query
information about firmware components.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Yotam Gigi <yotamg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
There are upcoming NIC (mlx5) use-cases where people want to avoid
building the mlxfw module, allow for that. The mlxsw module is
untouched and keeps selecting mlxfw.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Yotam Gigi <yotamg@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
For environments where flow-based ipv6 router is offloaded.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Use a macro for the static mapping between the enumeration of field
supported by the firmware for header re-write to the corresponding
network header field. This improves the readability of the code and
doesn't change any functionality.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Enable offloading of TC matching on ip ttl / hop-limit
As matching on ttl is supported only by newer HW brands (ConnectX-5),
we should do capability check before attempting to offload that.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The code section for offloading matches on ip tos (L3) should come
before and not after the one that deals with tcp/udp (L4) matches.
Otherwise, we might come up with wrong min-inline requirement, when
one attempts to match on both L3 and L4.
Fixes: fd7da28b280d ('net/mlx5e: Offload TC matching on ip tos / traffic-class')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Introduce a Page-Reuse mechanism in non-Striding RQ RX datapath.
A WQE (RX descriptor) buffer is a page, that in most cases was fully
wasted on a packet that is much smaller, requiring a new page for
the next round.
In this patch, we implement a page-reuse mechanism, that resembles a
`SW Striding RQ`.
We allow the WQE to reuse its allocated page as much as it could,
until the page is fully consumed. In each round, the WQE is capable
of receiving packet of maximal size (MTU). Yet, upon the reception of
a packet, the WQE knows the actual packet size, and consumes the exact
amount of memory needed to build a linear SKB. Then, it updates the
buffer pointer within the page accordingly, for the next round.
Feature is mutually exclusive with XDP (packet-per-page)
and LRO (session size is a power of two, needs unused page).
Performance tests:
iperf tcp tests show huge gain:
--------------------------------------------
num streams | BW before | BW after | ratio |
1 | 22.2 | 30.9 | 1.39x |
8 | 64.2 | 93.6 | 1.46x |
64 | 56.7 | 91.4 | 1.61x |
--------------------------------------------
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In the RX memory scheme of non Striding RQ, we use linear SKBs.
Keeping NET_IP_ALIGN in headroom can improve performance on some archs.
In addition, take this headroom into account when calculating the
LRO WQE size.
These are not needed in Striding RQ as they're done implicitly
within the non-linear SKB allocation.
Fixes: 1bfecfca565c ("net/mlx5e: Build RX SKB on demand")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Build the SKB over the receive packet instead of the
whole page. Getting the SKB's linear data and shared_info
closer improves locality.
In addition, this opens up the possibility to make use of
other parts of the page in the downstream page-reuse patch.
Fixes: 1bfecfca565c ("net/mlx5e: Build RX SKB on demand")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
NPU2 requires an extra explicit flush to an active GPU PID when
sending address translation shoot downs (ATSDs) to reliably flush the
GPU TLB. This patch adds just such a flush at the end of each sequence
of ATSDs.
We can safely use PID 0 which is always reserved and active on the
GPU. PID 0 is only used for init_mm which will never be a user mm on
the GPU. To enforce this we add a check in pnv_npu2_init_context()
just in case someone tries to use PID 0 on the GPU.
Signed-off-by: Alistair Popple <alistair@popple.id.au>
[mpe: Use true/false for bool literals]
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
For real-space designation asces the asce origin part is only a token.
The asce token origin must not be used to generate an effective
address for storage references. This however is erroneously done
within kvm_s390_shadow_tables().
Furthermore within the same function the wrong parts of virtual
addresses are used to generate a corresponding real address
(e.g. the region second index is used as region first index).
Both of the above can result in incorrect address translations. Only
for real space designations with a token origin of zero and addresses
below one megabyte the translation was correct.
Furthermore replace a "!asce.r" statement with a "!*fake" statement to
make it more obvious that a specific condition has nothing to do with
the architecture, but with the fake handling of real space designations.
Fixes: 3218f7094b6b ("s390/mm: support real-space for gmap shadows")
Cc: David Hildenbrand <david@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
Current DTLB load/store miss events (0x608/0x649) only counts 4K,2M and
4M page size.
Need to extend the events to support any page size (4K/2M/4M/1G).
The complete DTLB load/store miss events are:
DTLB_LOAD_MISSES.WALK_COMPLETED 0xe08
DTLB_STORE_MISSES.WALK_COMPLETED 0xe49
Signed-off-by: Kan Liang <Kan.liang@intel.com>
Cc: <stable@vger.kernel.org>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: eranian@google.com
Link: http://lkml.kernel.org/r/20170619142609.11058-1-kan.liang@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
The i2c-imx driver incorrectly uses readb()/writeb() to read and
write to the appropriate registers when performing a repeated start.
The appropriate imx_i2c_read_reg()/imx_i2c_write_reg() functions
should be used instead. Performing a repeated start results in
a kernel panic. The platform is imx.
Signed-off-by: Michail G Etairidis <m.etairidis@beck-ipc.com>
Fixes: ce1a78840ff7 ("i2c: imx: add DMA support for freescale i2c driver")
Fixes: 054b62d9f25c ("i2c: imx: fix the i2c bus hang issue when do repeat restart")
Acked-by: Fugang Duan <fugang.duan@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
IP6CB(skb)->nhoff is the offset of the nexthdr field in an IPv6
header, unless there are extension headers present, in which case
nhoff points to the nexthdr field of the last extension header.
In non-GRO code path, nhoff is set by ipv6_rcv before any XFRM code
is executed. Conversely, in GRO code path (when esp6_offload is loaded),
nhoff is not set. The following functions fail to read the correct value
and eventually the packet is dropped:
xfrm6_transport_finish
xfrm6_tunnel_input
xfrm6_rcv_tnl
Set nhoff to the proper offset of nexthdr in esp6_gro_receive.
Fixes: 7785bba299a8 ("esp: Add a software GRO codepath")
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
